Users Guide

• fedgovacl : 0
• nlbclusteracl: 0
l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 0 to 8
in multiples of 2.
ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4. The range is
from 0 to 9 in multiples of 3, when ipv4udfenable is selected. If not enabled, it is in
multiples of 2.
ipv6acl number Enter the keyword ipv6acl and then the number of FP blocks for IPv6. The range is
from 0 to 9 in multiples of 3.
ipv4qos number Enter the keyword ipv4qos and then the number of FP blocks for IPv4. The range is
from 0 to 8 in multiples of 2.
l2qos number Enter the keyword l2qos and then the number of FP blocks for l2 qos. The range is from
0 to 8 in multiples of 2.
l2pt number Enter the keyword l2pt and then the number of FP blocks for l2 protocol tunnelling. The
range is from 0 to 8 in multiples of 2.
Ipmacacl number Enter the keyword ipmacacl and then the number of FP blocks for IP and MAC ACL.
The range is from 0 to 9.
etsaclnumber Enter the keyword etsacl and then the number of FP blocks for ETS ACL. The range is
from 0 to 9.
nlbclusteracl
number
Enter the keyword nlbclusteracl and then the number of FP blocks for nlbcluster
ACL. The range is from 0 to 9. By default, the value is 0 and it supports 8 NLB arp entries
reserved for internal functionality.
NOTE: When you recongure CAM allocation, use the nlbclusteracl
number command to change the number of NLB ARP entries. The range is
from 0 to 9.
The default value is 0. At the default value of 0, eight NLB ARP
entries are available for use. This platform supports up to 512 CAM entries.
Select 1 to congure 256 entries. Select 2 to congure 512 entries. Even
though you can perform CAM carving to allocate the maximum number of
NLB entries, Dell Networking recommends that you use a maximum of 64 NLB
ARP entries.
vman-qos Enter the keyword vman-qos and then the number of FP blocks for VMAN QoS. The
range is from 0 to 9.
Ipv4pbr number Enter the keyword ipv4pbr and then the number of FP blocks for ipv4pbr ACL. The
range is from 0 to 8.Each PBR entry is carved out in double wide mode. While carving,
specify only even groups for PBR.
Openow number Enter the keyword openflow and then the number of FP blocks for open ow (multiples
of 4). The range is from 0 to 9 in multiples of 3.
fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The
range is from 0 to 8 in multiples of 2.
l2acl number
ipv4acl number
ipv6acl number,
ipv4qos number
l2qos numberl2pt
number ipmacacl
number
{nlbclusteracl]
Allocate space to each CAM region.
Enter 4 or 8 for the number of OpenFlow FP blocks.
• 4: Creates 242 entries for use by the OpenFlow controller (256 total entries minus the
14 entries reserved for internal functionality)
• 8: Creates 498 entries for use by the OpenFlow controller (512 total entries minus the
14 entries reserved for internal functionality)
Content Addressable Memory (CAM) 407