Concept Guide

enterprises.6027.3.10.1.2.10.1.2.1.3 = "/CORE_DUMP_DIR/FTP_STK_MEMBER/
f10cp_vrrp_140522124357_Stk1.acore.gz"
enterprises.6027.3.10.1.2.10.1.2.2.1 =
"/CORE_DUMP_DIR/FTP_STK_MEMBER/f10cp_sysd_140617134445_Stk0.acore.gz"
enterprises.6027.3.10.1.2.10.1.3.1.1 = "Fri Mar 14 11:51:46 2014"
enterprises.6027.3.10.1.2.10.1.3.1.2 = "Fri Nov 8 08:11:16 2013"
enterprises.6027.3.10.1.2.10.1.3.1.3 = "Fri May 23 05:05:16 2014"
enterprises.6027.3.10.1.2.10.1.3.2.1 = "Tue Jun 17 14:19:26 2014"
enterprises.6027.3.10.1.2.10.1.4.1.1 = 0
enterprises.6027.3.10.1.2.10.1.4.1.2 = 1
enterprises.6027.3.10.1.2.10.1.4.1.3 = 1
enterprises.6027.3.10.1.2.10.1.4.2.1 = 0
enterprises.6027.3.10.1.2.10.1.5.1.1 = "flashmntr"
enterprises.6027.3.10.1.2.10.1.5.1.2 = "l2mgr"
enterprises.6027.3.10.1.2.10.1.5.1.3 = "vrrp" Hex: 76 72 72 70
enterprises.6027.3.10.1.2.10.1.5.2.1 = "sysd" Hex: 73 79 73 64
The output above displays that the software core les generated by the system.
MIB Support for CAM
Dell EMC Networking provides a method to retrieve the CAM usage information. The following table lists the related MIB objects:
Table 109. MIB Objects for CAM
MIB Object OID Description
camUsageL2Pip
eLine
1.3.6.1.4.1.6027.3.7.1.1.2.1.11 Contains information about the pipe line number of the
chip on the layer 2 switch where CAM is located.
camUsageL3Pip
eLine
1.3.6.1.4.1.6027.3.7.1.1.3.1.19 Contains information about the pipe line number of the
chip on the layer 3 switch where CAM is located.
camUsageL3Ing
QosUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.12.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 ingress QOS.
camUsageL3Ing
AclUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.16.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 ingress ACL.
camUsageL3Eg
rAclUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.18.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 egress ACL.
camUsageL2Ing
AclUsed
1.3.6.1.4.1.6027.3.7.1.1.2.1.4.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 2 ingress ACL.
camUsageL2Eg
rAclUsed
1.3.6.1.4.1.6027.3.7.1.1.2.1.10.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 2 egress ACL.
NOTE: The last three digits of these OIDs correspond to the stack-unit, port-pipe, and pipe-line respectively. The values
corresponding to these elds are incremented by one before being displayed in the snmp walk output. As a result, the stack-unit
number, the port-pipe number, and the pipe-line number starts from 2 instead of 1.
Viewing the CAM MIB
• To view the CAM MIB generated by the system, use the following commands.
snmpwalk -c public -v 2c 10.16.210.24 1.3.6.1.4.1.6027.3.7.1.1.3.1.12
SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.12.1.1.1 = INTEGER: 0
902
Simple Network Management Protocol (SNMP)