Reference Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S6000

Dell Command Line Reference Guide for the

S6000 System

9.5(0.0)

Summary of content (1510 pages)

PAGE 1
Dell Command Line Reference Guide for the S6000 System 9.5(0.
PAGE 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
PAGE 3
Contents 1 About this Guide......................................................................................................37 Objectives............................................................................................................................................ 37 Audience.............................................................................................................................................. 37 Conventions.............................................................
PAGE 4
Control and Monitoring....................................................................................... 80 cam-acl............................................................................................................................................... 80 clear line.............................................................................................................................................. 82 configure..............................................................................
PAGE 5
show software ifm.............................................................................................................................130 show system...................................................................................................................................... 132 show tech-support........................................................................................................................... 136 ssh-peer-stack-unit....................................................
PAGE 6
ip control-plane egress-filter...................................................................................................... 175 show ip accounting access-list...................................................................................................175 Standard IP ACL Commands.............................................................................................................177 deny.....................................................................................................
PAGE 7
continue...................................................................................................................................... 232 description...................................................................................................................................234 match as-path.............................................................................................................................234 match community..............................................................
PAGE 8
permit tcp (for Extended IP ACLs)....................................................................................................282 seq arp (for Extended MAC ACLs).................................................................................................... 283 seq ether-type (for Extended MAC ACLs)........................................................................................285 seq (for IP ACLs)............................................................................................
PAGE 9
BGP IPv4 Commands....................................................................................................................... 322 address-family.............................................................................................................................322 aggregate-address...................................................................................................................... 323 bgp add-path............................................................................
PAGE 10
neighbor advertisement-start.................................................................................................... 364 neighbor allowas-in....................................................................................................................364 neighbor default-originate......................................................................................................... 365 neighbor description....................................................................................
PAGE 11
show ip bgp paths community...................................................................................................422 show ip bgp peer-group.............................................................................................................423 show ip bgp regexp.................................................................................................................... 425 show ip bgp summary.........................................................................................
PAGE 12
dcb-output..................................................................................................................................464 dcb-policy output.......................................................................................................................465 clear ets counters....................................................................................................................... 466 show interface ets....................................................................
PAGE 13
show hardware layer3................................................................................................................. 510 show hardware stack-unit...........................................................................................................511 show hardware stack-unit buffer............................................................................................... 518 show hardware system-flow...................................................................................
PAGE 14
ip domain-name..........................................................................................................................547 ip domain-list.............................................................................................................................. 548 ip host..........................................................................................................................................549 clear host....................................................................
PAGE 15
disable............................................................................................................................................... 583 interface............................................................................................................................................ 584 member-vlan.................................................................................................................................... 585 mode...................................................
PAGE 16
ip igmp snooping fast-leave....................................................................................................... 623 ip igmp snooping flood.............................................................................................................. 623 ip igmp snooping last-member-query-interval........................................................................ 624 ip igmp snooping mrouter................................................................................................
PAGE 17
shutdown.................................................................................................................................... 684 speed (Management interface).................................................................................................. 685 stack-unit portmode.................................................................................................................. 686 switchport........................................................................................
PAGE 18
ip name-server.................................................................................................................................. 732 ip proxy-arp.......................................................................................................................................733 ip route.............................................................................................................................................. 733 ip source-route..........................................
PAGE 19
cam-acl............................................................................................................................................. 786 26 Intermediate System to Intermediate System (IS-IS)................................788 adjacency-check.............................................................................................................................. 788 advertise..................................................................................................................
PAGE 20
isis priority......................................................................................................................................... 824 is-type................................................................................................................................................825 log-adjacency-changes................................................................................................................... 826 lsp-gen-interval.............................................
PAGE 21
mac learning-limit...................................................................................................................... 866 mac learning-limit learn-limit-violation.................................................................................... 868 mac learning-limit mac-address-sticky.................................................................................... 869 mac learning-limit station-move-violation...........................................................................
PAGE 22
show lldp neighbors................................................................................................................... 907 show lldp statistics......................................................................................................................908 LLDP-MED Commands....................................................................................................................908 advertise med guest-voice.....................................................................
PAGE 23
msti....................................................................................................................................................944 name................................................................................................................................................. 945 protocol spanning-tree mstp...........................................................................................................946 revision........................................................
PAGE 24
graceful-restart role....................................................................................................................985 ip ospf auth-change-wait-time................................................................................................. 986 ip ospf authentication-key..........................................................................................................987 ip ospf cost............................................................................................
PAGE 25
timers spf...................................................................................................................................1043 timers throttle lsa all................................................................................................................. 1044 timers throttle lsa arrival........................................................................................................... 1045 35 Policy-based Routing (PBR)......................................................
PAGE 26
show running-config monitor session.......................................................................................... 1080 source (port monitoring)................................................................................................................ 1081 38 Private VLAN (PVLAN).....................................................................................1084 ip local-proxy-arp...........................................................................................................
PAGE 27
match ip dscp............................................................................................................................ 1120 match ip precedence.................................................................................................................1121 match mac access-group......................................................................................................... 1122 match mac dot1p....................................................................................
PAGE 28
auto-summary................................................................................................................................. 1161 clear ip rip........................................................................................................................................ 1162 debug ip rip......................................................................................................................................1162 default-information originate...............................
PAGE 29
43 Rapid Spanning Tree Protocol (RSTP)........................................................ 1205 bridge-priority.................................................................................................................................1205 debug spanning-tree rstp...............................................................................................................1206 description................................................................................................................
PAGE 30
timeout login response.............................................................................................................1246 username................................................................................................................................... 1247 RADIUS Commands........................................................................................................................1249 debug radius...............................................................................
PAGE 31
ip ssh connection-rate-limit.....................................................................................................1283 ip ssh hostbased-authentication..............................................................................................1284 ip ssh key-size........................................................................................................................... 1285 ip ssh password-authentication..........................................................................
PAGE 32
sflow collector................................................................................................................................. 1321 sflow enable (Global)...................................................................................................................... 1323 sflow enable (Interface).................................................................................................................. 1323 sflow extended-switch enable.............................................
PAGE 33
logging facility........................................................................................................................... 1367 logging history.......................................................................................................................... 1368 logging history size................................................................................................................... 1369 logging monitor....................................................................
PAGE 34
calendar set..................................................................................................................................... 1410 clock read-calendar........................................................................................................................ 1411 clock summer-time date................................................................................................................ 1412 clock summer-time recurring.................................................
PAGE 35
description...................................................................................................................................... 1448 ip vrf forwarding..............................................................................................................................1449 interface management................................................................................................................... 1450 maximum dynamic-routes..................................................
PAGE 36
fail-mode.........................................................................................................................................1482 vxlan-instance.................................................................................................................................1482 vxlan-instance (VAP)....................................................................................................................... 1483 max_backoff.........................................................
PAGE 37
About this Guide 1 This book provides information about the Dell Networking OS command line interface (CLI). This book also includes information about the protocols and features found in Dell S6000 platform.
PAGE 38
[X] Keywords and parameters within brackets are optional. x|y Keywords and parameters separated by a bar require you to choose one option. x||y Keywords and parameters separated by a double bar allows you to choose any or all of the options. Information Icons This book uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data.
PAGE 39
CLI Basics 2 This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Command Line When the system boots successfully, you are positioned on the command line in EXEC mode and not prompted to log in. You can access the commands through a serial console port or a Telnet session.
PAGE 40
When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a command mode there are several ways to access help. To obtain a list of keywords at any command mode: Type a ? at the prompt or after a keyword. There must always be a space before the ?.
PAGE 41
tacacs telnet tftp trace-group trace-list Dell(conf)#ip Interface configuration for TACACS+ Specify telnet options TFTP configuration commands Named trace-list Named trace-list When entering commands, you can take advantage of the following timesaving features: • The commands are not case-sensitive. • You can enter partial (truncated) command keywords. For example, you can enter interface teng 0/0 for the interface tengigabitethernet 0/0 command. • To complete keywords in commands, use the TAB key.
PAGE 42
Navigating the CLI Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with the hostname command. • CLI mode is the second part of the prompt and reflects the current CLI mode. For a list of the Dell Networking OS command modes, refer to the command mode list in the Accessing the Command Line section.
PAGE 43
show run | grep ethernet does not return the previous search result because it only searches for instances containing a noncapitalized “ethernet” show run | grep Ethernet ignore-case returns instances containing both “Ethernet” and “ethernet” no-more does not paginate the display output save copies the output to a file for future use Displaying All Output To display the output all at once (not one screen at a time), use the no-more option after the pipe.
PAGE 44
Based on whether VRF feature is identified as supported in the Feature Configuration file, configuration command feature vrf becomes available for usage. This command will be stored in running-configuration and will precede all other VRF-related configurations. NOTE: The MXL and Z9000 platforms currently do not support VRF. These platforms support only the management and default VRFs, which are available by default. As a result, the feature vrf command is not available for these platforms.
PAGE 45
Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms. Example Dell#show feature Feature State -----------------------------VRF enabled Command Modes To navigate and launch various CLI modes, use specific commands. Navigation to these modes is described in the following sections. BGP ADDRESS-FAMILY Mode To enable or configure IPv4 for BGP, use BGP ADDRESS-FAMILY mode.
PAGE 46
CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP). To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command. The prompt changes to include (conf-controlcpuqos). You can return to CONFIGURATION mode by using the exit command. DHCP Mode To enable and configure Dynamic Host Configuration Protocol (DHCP), use DHCP mode.
PAGE 47
1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include (conf-mgmt-eis). You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode. This mode allows you to view settings and enter EXEC Privilege mode, which is used to configure the device.
PAGE 48
To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. The prompt changes to include the designated interface and slot/port number.
PAGE 49
To enter ISIS ADDRESS-FAMILY mode: 1. Verify that you are logged in to ROUTER ISIS mode. 2. Enter the command address-family ipv6 unicast. The prompt changes to include (confrouter_isis-af_ipv6). LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information, refer to Link Layer Discovery Protocol (LLDP). To enter LLDP mode: 1. To enable LLDP globally, verify that you are logged in to CONFIGURATION mode.
PAGE 50
To enter MONITOR SESSION mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the monitor session command then the session ID. The prompt changes to include (confmon-sess-sessionID). MULTIPLE SPANNING TREE (MSTP) Mode To enable and configure MSTP, use MULTIPLE SPANNING TREE mode. For more information, refer to Multiple Spanning Tree Protocol (MSTP). To enter MULTIPLE SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 51
PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode. To enter PREFIX-LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ip prefix-list command. Include a name for the prefix list. The prompt changes to include (conf-nprefixl). You can return to CONFIGURATION mode by using the exit command. PROTOCOL GVRP Mode To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For more information, refer to GARP VLAN Registration (GVRP).
PAGE 52
2. Use the router bgp command then enter the AS number. The prompt changes to include (confrouter_bgp). You can return to CONFIGURATION mode by using the exit command. ROUTER ISIS Mode To enable and configure Intermediate System to Intermediate System (ISIS), use ROUTER ISIS mode. For more information, refer to Intermediate System to Intermediate System (IS-IS). To enter ROUTER ISIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the router isis command.
PAGE 53
SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode. For more information, refer to Spanning Tree Protocol (STP). To enter SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree stp-id command. The prompt changes to include (conf-stp). You can return to CONFIGURATION mode by using the exit command. TRACE-LIST Mode To configure a Trace list, use TRACE-LIST mode. To enter TRACE-LIST mode: 1.
PAGE 54
3 File Management This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. cd Change to a different working directory. S6000 Syntax Parameters cd directory directory (OPTIONAL) Enter one of the following: • flash: (internal Flash) or any sub-directory • usbflash: (internal Flash) or any sub-directory Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 55
HTTP Copy via CLI Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). This feature is supported on S6000 platform. Syntax copy http://10.16.206.77/sample_file flash://sample_filecopy flash://sample_file http://10.16.206.77/sample_file You can copy from the server to the switch and vice-versa. Parameters copy http: flash: Address or name of remote host []: 10.16.206.
PAGE 56
compressedconfig file-url Enter the keyword compressed-config to copy one file, after optimizing and reducing the size of the configuration file, to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field).
PAGE 57
Usage Information Version 8.4.1.0 Added IPv6 addressing support for FTP, TFTP, and SCP. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added usbflash and rpm0usbflash commands on ESeries ExaScale. Version 7.6.1.0 Introduced on the S-Series and added the SSH port number to the SCP prompt sequence on all systems. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 58
In this copy scp: flash: example, specifying SCP in the first position indicates that the target is to be specified in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal Flash. The source is on a secure server running SSH, so you are prompted for the user datagram protocol (UDP) port of the SSH server on the remote host. Example Dell#copy scp: flash: Address or name of remote host []: 10.11.199.
PAGE 59
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 60
Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Example Dell#dir Directory of flash: 1 -rwx 6478482 May 13 101 16:54:34 E1200.BIN flash: 64077824 bytes total (57454592 bytes free) Dell# Related Commands cd – changes the working directory. format flash (S-Series) Erase all existing files and reformat the filesystem in the internal flash memory.
PAGE 61
CAUTION: This command deletes all files, including the startup configuration file. So, after executing this command, consider saving the running config as the startup config (use the write memory command or copy run start command). Related Commands copy – copies the current configuration to either the startup-configuration file or the terminal. show file-systems – displays information about the file systems on the system. fsck flash Checks the flash file system for errors.
PAGE 62
Related Commands • copy — copy one file to another location. • show file-systems — Display information about the file systems on the system. rename Rename a file in the local file system. S6000 Syntax Parameters rename url url url Enter the following keywords and a filename: • For a file on the internal Flash, enter flash:// followed by the filename. • For a file on an external USB drive, enter usbflash:// followed by the filename.
PAGE 63
show boot system Displays information about boot images currently configured on the system. S6000 Syntax Parameters show boot system {stack-unit {0-11 | 0-7 | 0-5 | all}} all Enter the keyword all to display the boot image information for all line cards and rpms. stack-unit Enter the keyword stack-unit followed by a number to display boot image information for a stack-unit. The S6000 range is from 0 to 5.
PAGE 64
show bootvar Display the variable settings for the boot parameters. S6000 Syntax show bootvar Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example 64 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 65
show file-systems Display information about the file systems on the system. S6000 Syntax show file-systems Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Command Fields Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 66
Field Description • Prefixes Related Commands w = write access Displays the name of the storage location. format flash (S-Series) – Erases all the existing files and reformats the filesystem in the internal flash memory on the S-Series. show os-version Display the release and software image version information of the image file specified.
PAGE 67
Example Version 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 68
aaa for the current AAA configuration acl for the current ACL configuration arp for the current static ARP configuration as-path for the current AS-path configuration bfd for the current BFD configuration bgp for the current BGP configuration boot for the current boot configuration cam-profile for the current CAM profile in the configuration class-map for the current class-map configuration communitylist for the current community-list configuration ecmp-group for the current ECMP gr
PAGE 69
File Management lldp for the current LLDP configuration load-balance for the current port-channel loadbalance configuration logging for the current logging configuration mac for the current MAC ACL configuration mac-addresstable for the current MAC configuration managementeis for the current management EIS configuration managementroute for the current Management port forwarding configuration mld for the current MLD configuration monitor for the current Monitor configuration mroute for th
PAGE 70
rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configuration snmp for the current SNMP configuration spanningtree for the current spanning tree configuration static for the current static route configuration status for the file status information tacacs+ for the current TACACS+ configuration tftp for the current TFTP configuration trace-group for the current trace-group configuration trace-list for the current trace-
PAGE 71
Version 9.0.2.0 Introduced on the S6000. Version 9.2. (0.0) Added support for the tunnel and EIS interface types. Version 9.0.0.0 Added support for the VLT option. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added the hardware-monitor option. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 72
show startup-config Display the startup configuration. S6000 Syntax show startup-config Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 73
show version Display the current Dell Networking Operating System (OS) version information on the system. S6000 Syntax show version Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Command Fields File Management Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 74
Example (SSeries) Lines Beginning With Description 1 Route Processor... Hardware configuration of the system, including the number and type of physical interfaces available Dell#show version Dell Real Time Operating System Software Dell Operating System Version: 1.0 Dell Application Software Version: E7-8-1-13 Copyright (c) 1999-2008 by Dell Force10 Networks, Inc.
PAGE 75
Dell(conf-if-te-0/5)# Dell# Example (S6000) Dell#S6000#show version Dell Real Time Operating System Software Dell Operating System Version: 2.0 Dell Application Software Version: 9-4(0-119) Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Tue Mar 18 10:32:02 PDT 2014 Build Path: /work.
PAGE 76
A Enter the keywordA to upgrade the bootflash partition A B Enter the keyword B to upgrade the bootflash partition B. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0(0.
PAGE 77
Parameters all Enter the keyword all to change both the bootflash and bootselector images. bootflashimage Enter the keyword bootflash-image to change the bootflash image.. bootselectorimage Enter the keyword bootselector-image to upgrade the BIOS system image. 0–5 Enter the keywords 0–5 to upgrade only the mentioned stack-unit . all Enter the keywords all to upgrade the member stack-units. booted Enter the keyword booted to upgrade from the current image in the S6000.
PAGE 78
Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for TFTP and SCP. Version 7.6.1.0 Introduced on the S-Series. Usage Information You must reload Dell Networking OS after executing this command.
PAGE 79
Example • verify sha256 flash://img-file • verify sha256 flash://img-file Without Entering the Hash Value for Verification using SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.bin SHA256 hash for FTOS-SE-9.5.0.0.bin: e6328c06faf814e6899ceead219afbf9360e986d692988023b749e6b2093e93 3 Entering the Hash Value for Verification using SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.bin e6328c06faf814e6899ceead219afbf9360e986d692988023b749e6b2093e93 3 SHA256 hash VERIFIED for FTOS-SE-9.5.0.
PAGE 80
4 Control and Monitoring This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP) as they apply to the following Dell Networking S6000 platform. NOTE: Starting in version 9.0.2.
PAGE 81
cam-acl {default | l2acl number ipv4acl number ipv6acl number, ipv4qos number l2qos numberl2ptnu mber ipmacacl number ecfmacl number [vmanqos | vmandual-qos number} Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. Enter 4 or 8 for the number of OpenFlow FP blocks.
PAGE 82
The total amount of space allowed is 16 FP Blocks. System flow requires three blocks and these blocks cannot be reallocated. The ipv4acl profile range is from 1 to 4. When configuring space for IPv6 ACLs, the total number of Blocks must equal 13. Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10). If you enabled BMP 3.
PAGE 83
Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode. S6000 Syntax Parameters configure [terminal] terminal (OPTIONAL) Enter the keyword terminal to specify that you are configuring from the terminal. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 84
disable Return to EXEC mode. S6000 Syntax Parameters disable [level] level (OPTIONAL) Enter a number for a privilege level of the Dell Networking OS. The range is from 0 to 15. The default is 1. Defaults 1 Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 85
Command Modes • CONFIGURATION • INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Control and Monitoring Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.
PAGE 86
enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. S6000 Syntax Parameters enable [level] level (OPTIONAL) Enter a number for a privilege level of Dell Networking OS. The range is from 0 to 15. Defaults 15 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 87
Related Commands enable password — configures a password for the enable command and to access a privilege level. enable optic-info-update interval Enable polling intervals of optical information updates for simple network management protocol (SNMP). S6000 Syntax enable optical-info-update interval seconds To disable optical power information updates, use the no enable opticalinfo-update interval command. Parameters interval seconds Enter the keyword interval then the polling interval in seconds.
PAGE 88
end Return to EXEC Privilege mode from other command modes (for example, CONFIGURATION or ROUTER OSPF modes). S6000 Syntax end Command Modes • CONFIGURATION • SPANNING TREE • MULTIPLE SPANNING TREE • LINE • INTERFACE • TRACE-LIST • VRRP • ACCESS-LIST • PREFIX-LIST • AS-PATH ACL • COMMUNITY-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP Command History This guide is platform-specific.
PAGE 89
exec-banner Enable the display of a text string when the user enters EXEC mode. S6000 Syntax exec-banner To disable the banner on terminal lines, use the no exec-banner command. Defaults Enabled on all lines (if configured, the banner appears). Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 90
Parameters minutes Enter the number of minutes of inactivity on the system before disconnecting the current session. The range is from 0 to 35791. The default is 10 minutes for the console line and 30 minutes for the VTY line. seconds (OPTIONAL) Enter the number of seconds. The range is from 0 to 2147483. The default is 0 seconds. Defaults 10 minutes for console line; 30 minutes for VTY lines; 0 seconds Command Modes LINE Command History This guide is platform-specific.
PAGE 91
Command History • LINE, INTERFACE • TRACE-LIST • PROTOCOL GVRP • SPANNING TREE • MULTIPLE SPANNING TREE • MAC ACCESS LIST • ACCESS-LIST • AS-PATH ACL • COMMUNITY-LIST • PREFIX-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 92
Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to enable the FTP server to listen to that VRF instance. NOTE: Use this attribute to specify the VRF that is used by the FTP server to accept client connections. If no VRF is specified, then the default VRF is used. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 93
329 bytes received in 0.018 seconds (17.95 Kbytes/s) ftp> ftp-server topdir Specify the top-level directory to be accessed when an incoming FTP connection request is made. S6000 Syntax Parameters ftp-server topdir directory directory Enter the directory path. Defaults The internal flash is the default directory. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 94
ftp-server username — sets a username and password for incoming FTP connections to the E-Series. ftp-server username Create a user name and associated password for incoming FTP server sessions. S6000 Syntax ftp-server username username password [encryption-type] password To delete a user name and its password, use the no ftp-server username username command. Parameters username Enter a text string up to 40 characters long as the user name.
PAGE 95
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. hostname Set the host name of the system. S6000 Syntax Parameters hostname name name Enter a text string, up to 32 characters long. Defaults Dell Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 96
ip ftp password Specify a password for outgoing FTP connections. S6000 Syntax ip ftp password [encryption-type] password To remove a password and return to the default setting, use the no ip ftp password [password] command. Parameters encryptiontype password (OPTIONAL) Enter one of the following numbers: • 0 (zero) for an unecrypted (clear text) password • 7 (seven) for a hidden text password Enter a string up to 40 characters as the password. Defaults Not configured.
PAGE 97
ip ftp source-interface Specify an interface’s IP address as the source IP address for FTP connections. S6000 Syntax ip ftp source-interface interface To delete an interface, use the no ip ftp source-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16383. • For a Port Channel interface, enter the keyword portchannel then a number.
PAGE 98
Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TFTP client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 99
ip ftp username Assign a user name for outgoing FTP connection requests. S6000 Syntax ip ftp username username To return to anonymous FTP connections, use the no ip ftp username [username] command. Parameters username Enter a text string as the user name up to 40 characters long. Defaults No user name is configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 100
ip ftp vrf Configures an FTP client with a VRF that is used to connect to the FTP server. Syntax ip ftp [vrf vrf-name] To undo the FTP client configuration, use the ip ftp [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the FTP client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 101
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. ip ssh server — enables the secure shell (SSH) server on the system. ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF.
PAGE 102
FTOS(conf)#ip telnet server vrf management FTOS(conf)#no ip telnet server vrf ip telnet source-interface Set an interface’s IP address as the source address in outgoing packets for Telnet sessions. S6000 Syntax ip telnet source-interface interface To return to the default setting, use the no ip telnet source-interface [interface] command.
PAGE 103
Related Commands Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command telnet — telnet to another device. ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server.
PAGE 104
ftp-server username — sets a username and password for incoming FTP connections to the E-Series. line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. S6000 Syntax Parameters line {aux 0 |console 0 | vty number [end-number]} aux 0 Enter the keyword aux 0 to configure the auxiliary terminal connection. console 0 Enter the keyword console 0 to configure the console port.
PAGE 105
E-Series Original command Usage Information You cannot delete a terminal connection. Related Commands access-class — restricts the incoming connections to a particular IP address in an IP access control list (ACL). password — specifies a password for users on terminal lines. motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. S6000 Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines.
PAGE 106
ping Test connectivity between the system and another device by sending echo requests and waiting for replies.
PAGE 107
tos (IPv4 only) Enter the type of service required. The range is from 0 to 255. The default is 0. df-bit (IPv4 only) Enter Y or N for the “don't fragment” bit in IPv4 header. • N: Do not set the “don't fragment” bit. • Y: Do set “don't fragment” bit Default is No. validate-reply (IPv4 only) Enter Y or N for reply validation. • N: Do not validate reply data. • Y: Do validate reply data. Default is No.
PAGE 108
Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Added support for the outgoing-interface option for link-local IPv6 addressing on the S4820T. Usage Information Version 8.3.12.0 Added support for the outgoing-interface option for link-local IPv6 addressing on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.
PAGE 109
Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2 seconds: Reply to request 1 from 172.31.1.208 0 ms Reply to request 1 from 172.31.1.216 0 ms Reply to request 1 from 172.31.1.205 16 ms :: Reply to request 5 from 172.31.1.209 0 ms Reply to request 5 from 172.31.1.66 0 ms Reply to request 5 from 172.31.1.87 0 ms Dell# Example (IPv6) Dell#ping 100::1 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds: !!!!! Success rate is 100.
PAGE 110
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. If there is a change in the configuration, FTOS prompts you to save the new configuration. Or you can save your running configuration with the copy running-config command. Use the conditional parameter if any configuration changes made to the nvram, such as stack-group and fanout configurations, must be saved. send Send messages to one or all terminal line users.
PAGE 111
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. Messages can contain an unlimited number of lines; however, each line is limited to 255 characters. To move to the next line, use . To send the message use CTR-Z; to abort a message, use CTR-C. service timestamps To debug and log messages, add time stamps.
PAGE 112
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.
PAGE 113
Example Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 114
no Display all of the commands that may be preceded by the keyword no, which is the keyword used to remove a command from the running-configuration. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 115
show cpu-traffic-stats View the CPU traffic statistics. S6000 Syntax Parameters show cpu-traffic-stats [port number | all | cp ] port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568. all (OPTIONAL) Enter the keyword all to display traffic statistics on all the interfaces receiving traffic, sorted based on the traffic. cp (OPTIONAL) Enter the keyword cp to display traffic statistics on the specified CPU.
PAGE 116
Example Dell#show cpu-traffic-stats Processor : CP -------------Received 100% traffic on GigabitEthernet 8/2 Total packets:100 LLC:0, SNAP:0, IP:100, ARP:0, other:0 Unicast:100, Multicast:0, Broadcast:0 Processor : RP1 --------------Received 62% traffic on GigabitEthernet 8/2 Total packets:500 LLC:0, SNAP:0, IP:500, ARP:0, other:0 Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on GigabitEthernet 8/1 Total packets:300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Pr
PAGE 117
Example Dell#show debug Generic IP: IP packet debugging is on for ManagementEthernet 0/0 Port-channel 1-2 Port-channel 5 GigabitEthernet 4/0-3,5-6,10-11,20 GigabitEthernet 5/0-1,5-6,10-11,15,17,19,21 ICMP packet debugging is on for GigabitEthernet 5/0,2,4,6,8,10,12,14,16 Dell# show environment View S-Series and Z-Series system component status (for example, temperature or voltage).
PAGE 118
Version 8.3.11.1 Introduced on the Z9000. Version 7.8.1.0 The output of the show environment fan command for the S-Series is changed to display fan speeds instead of showing the fan status as up or down. Usage Information The following example shows the output of the show environment fan command.
PAGE 119
0 0 0 1 down up UNKNOWN AC down up 0 6504 Dell#show environment thermal-sensor -- Thermal Sensor Readings (deg C) -- Unit Sensor0 Sensor1 Sensor2 Sensor3 Sensor4 Sensor5 Sensor6 ---------------------------------------------------------------------------------0 39 36 37 37 31 31 46 show inventory Display the S-Series or Z-Series switch type, components (including media), and Dell Networking Operating System (OS), including hardware identification numbers and configured protocols.
PAGE 120
Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.4 Output expanded to include Piece Part ID (PPID) and eSR4 optics. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced this version of the command for S-Series. SSeries output differs from E-Series. Usage Information If there are no fiber ports in the unit, just the header under show inventory media displays. If there are fiber ports but no optics inserted, the output displays Media not present or accessible.
PAGE 121
0 7 APF11200012UR1 0 8 APF12300017GEY 0 9 APF12300017GEY 0 10 APF12300017GEY Related Commands QSFP QSFP QSFP QSFP 40GBASE-CR4-1M Yes 40GBASE-CR4-1M Yes 40GBASE-CR4-1M Yes 40GBASE-CR4-1M Yes • show interfaces — displays the interface configuration. • show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show memory View current memory usage on the switch.
PAGE 122
Usage Information The output for show memory displays the memory usage of LP part (sysdlp) of the system. The sysdlp is an aggregate task that handles all the tasks running on the SSeries’ CPU.
PAGE 123
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 124
0xbad9a000 0.00% 0.00% 0xbadb4000 0.00% 0.00% 0xbadc9000 0.00% 0.00% 0xbae22000 0.00% 0.02% 0 0 0 0 0 30 10 60 0 evagt 3 ipc 1 sysReaper 6 tme 0 0.00% 10000 0.00% 10000 0.00% 10000 0.00% Dell#show processes cpu management-unit ? <1-99> Number of tasks with highest CPU usage last 5 seconds details Detail CPU utilization | Pipe through a command Dell#show processes cpu management-unit details CPUID 5sec 1min 5min -------------------------------------------------CORE 0 11.73 10.79 12.82 CORE 2 11.
PAGE 125
details | Detail CPU utilization Pipe through a command Dell#show processes cpu management-unit CPUID 5sec 1min 5min -------------------------------------------------CORE 0 9.54 9.92 12.82 CORE 2 10.74 11.56 14.31 Overall 10.14 10.74 13.56 PID Runtime(ms) 1Min 5Min TTY 0x00000000 45040 13.20% 12.94% 0 0x000001ac 25750 2.48% 3.40% 0 0x0000019a 10650 1.16% 2.50% 0 0x000003a5 860 0.22% 0.28% 0 0x000001ad 520 0.30% 0.16% 0 0x000004ba 330 0.36% 0.09% 0 0x000000c9 1240 0.15% 0.44% 0 0x000000e0 530 0.12% 0.
PAGE 126
show processes memory (S-Series) — displays CPU usage information based on processes running in an S-Series. show processes ipc flow-control Display the single window protocol queue (SWPQ) statistics. S6000 Syntax show processes ipc flow-control [cp] Syntax show processes ipc flow-control [cp | rp1 | rp2 | stack-unit] Parameters Parameters cp (OPTIONAL) Enter the keyword cp to view the control processor’s SWPQ statistics.
PAGE 127
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 128
show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system. S6000 Syntax Parameters show processes memory {management-unit | stack unit {unit-id | all | summary}} managementunit Enter the keyword management-unit for CPU memory usage of the stack management unit. stack unit unit id Enter the keyword stack unit then a stack unit ID of the member unit for which to display memory usage on the forwarding processor. The range is from 0 to 7.
PAGE 129
show processes memory output Field Description MaxUsed: Total maximum memory used ever (history indicated with time stamp) CurrentUsed: Total memory currently in use CurrentFree: Total system memory available SharedUsed: Total used shared memory SharedFree: Total free shared memory PID Process ID Process Process Name ResSize Actual resident size of the process in memory Size Process test, stack, and data size Allocs Total dynamic memory allocated Frees Total dynamic memory freed Max
PAGE 130
Example (managementunit) Dell#show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249856 50572 0 50572 50572 323 frrp 5206016 241664 369238 0 369238 369238 322 xstp 7430144 2928640 38328 0 38328 38328 321 pim 5267456 823296 62168 0 62168 62168 314 igmp 4960256 380928 18588 16564 1
PAGE 131
stack-unit unitID • For a Port Channel interface, enter the keyword portchannel then a number: The range is from 1 to 128. • For a 10G Ethernet interface, enter the keyword TenGigabitEthernet. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE. Enter the keyword stack-unit then the stack member number to display IFM information for that unit. The range is from 0 to 1. NOTE: This option is only available on the S-Series.
PAGE 132
LACP 0 0x00000000 0x00000000 0x8000383f 0x00000000 35 DHCP 0 0x00000000 0x00000000 0x800000c2 0x0000c000 37 V6RAD 0 0x00000433 0x00030000 0x00000000 0x00000000 0 Unidentified Client0 0x006e0002 0x00000000 0x00000000 0x00000000 0 Dell# show system Display the status of all stack members or a specific member.
PAGE 133
Version 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, use the show reload-type command. Modified the show system stack-unit command output to support Piece Part ID (PPID). Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot codes display as "Present". Version 7.7.1.0 Added Master Priority field. Version 7.6.
PAGE 134
Example (S6000) Dell#show system Stack MAC : 90:b1:1c:f4:9b:79 Reload-Type : normal-reload] normal-reload [Next boot : -- Unit 0 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.
PAGE 135
-- Unit 0 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.0 Num Ports : 128 Up Time : 21 min, 8 sec Dell Networking OS Version : 9-4(0-168) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : 3.1.1.2 Boot Selector : 3.1.0.
PAGE 136
show tech-support Display a collection of data from other show commands, necessary for Dell Networking technical support to perform troubleshooting on S-Series or Z-Series switches. S6000 Syntax Parameters show tech-support [stack-unit unit-id | page] stack-unit (OPTIONAL) Enter the keywords stack-unit to view CPU memory usage for the stack member designated by unit-id. The unit ID range for the S6000 is from 0 to 7. page (OPTIONAL) Enter the keyword page to view 24 lines of text at a time.
PAGE 137
|except regular-expression | find regular-expression | save flash://result This display output is an accumulation of the same information that is displayed when you execute one of the following show commands: Example (SSeries) • show version • show clock • show running-config • show system stack-ports • show interfaces • show process memory • show process cpu • show file system • show system • show environment • show ip traffic • show ip management route • show ip route summary •
PAGE 138
Example (SSeries) Dell#show tech-support stack-unit 0 ----------------------------------- show version ------------------------------Dell Real Time Operating System Software Dell Operating System Version: 2.0 Dell Application Software Version: 9-4(0-168) Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Sun Mar 23 22:17:49 PDT 2014 Build Path: /work.
PAGE 139
ssh-peer-stack-unit Open an SSH connection to the peer stack-unit. Syntax Parameters ssh-peer-stack-unit [-l username] -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 140
Parameters host Enter the name of a server. ip-address Enter the IPv4 address in dotted decimal format of the server. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. vrf instance (Optional) Enter the keyword vrf then the VRF instance name.
PAGE 141
Example Version 8.3.12.0 Introduced on the S4810. Added support for sourceinterface for link-local IPv6 addressing. Version 8.3.11.1 Introduced on the Z9000. Version 8.2.1.0 Introduced on the E-Series ExaScale (IPv6). Increased the number of VLANs on ExaScale to 4094 (was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). Version 7.9.1.0 Introduced VRF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 142
terminal length Configure the number of lines displayed on the terminal screen. S6000 Syntax Parameters terminal length screen-length screen-length Enter a number of lines. Entering zero causes the terminal to display without pausing. The range is from 0 to 512. Defaults 24 lines Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 143
Parameters host Enter the name of device. ip-address Enter the IP address of the device in dotted decimal format. ipv6-address Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults • Timeout = 5 seconds • Probe count = 3 • 30 hops max • 40 byte packet size • UDP port = 33434 Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 144
(default is 1), maximum TTL (default is 30), and port number (default is 33434). To keep the default setting for those parameters, press the ENTER key. For IPv6, you are prompted for a minimum hop count (default is 1) and a maximum hop count (default is 64). Example (IPv4) Dell#traceroute www.Dell Networking.com Translating "www.Dell Networking.com"...domain server (10.11.0.1) [OK] Type Ctrl-C to abort. ----------------------------------------------Tracing the route to www.Dell Networking.com (10.11.84.
PAGE 145
undebug all Disable all debug operations on the system. S6000 Syntax undebug all Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 146
NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000 Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 147
terminal Enter the keyword terminal to copy the current running configuration to the terminal. This command is similar to the show running-config command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Control and Monitoring Version 9.0.2.
PAGE 148
5 802.1X An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking operating software supports remote authentication dial-in service (RADIUS) and active directory environments using 802.1X Port Authentication.
PAGE 149
debug dot1x Display 802.1X debugging information. S6000 Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all 802.1X debug messages. auth-pae-fsm Enable authentication PAE FSM debug messages. backend-fsm Enable backend FSM debug messages. eapol-pdu Enable the EAPOL frame trace and related debug messages. interface interface Restricts the debugging information to an interface.
PAGE 150
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 151
dot1x auth-server Configure the authentication server to RADIUS. S6000 Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 152
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: • Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command).
PAGE 153
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. dot1x authentication (Interface) — Enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface.
PAGE 154
Related Commands dot1x authentication (Configuration) — Enable dot1x globally. dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. S6000 Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Defaults Not configured.
PAGE 155
If the host fails authentication for the designated number of times, the authenticator places the port in authentication failed VLAN (dot1x auth-failvlan). NOTE: You can create the Layer 3 portion of a guest VLAN and authentication fail VLANs regardless if the VLAN is assigned to an interface or not. After an interface is assigned a guest VLAN (which has an IP address), routing through the guest VLAN is the same as any other traffic. However, the interface may join/leave a VLAN dynamically.
PAGE 156
Usage Information Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.0 Added the multi-auth option on the C-Series and S-Series. Version 8.3.2.0 Added the single-host and multi-host options on the C-Series, E-Series, and S-Series. • Single-host mode authenticates only one host per authenticator port and drops all other traffic on the port. • Multi-host mode authenticates the first host to respond to an Identity Request and then permits all other traffic on the port.
PAGE 157
Version 8.4.1.0 Usage Information Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-authbypass command. dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. S6000 Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command.
PAGE 158
dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode. S6000 Syntax Parameters dot1x max-supplicants number number Enter the number of supplicants that can be authenticated on a single port in Multi-auth mode. The range is from 1 to 128. The default is 128. Defaults 128 hosts can be authenticated on a single authenticator port.
PAGE 159
Parameters forceauthorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly deauthorize a port. Defaults none Command Modes Auto Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 160
Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.6.1.
PAGE 161
Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized.
PAGE 162
Version 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. S6000 Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 163
Where the default values are as follows: dot1x server-timeout (30 seconds), radius-server retransmit (3 seconds), and radius-server timeout (5 seconds). For example: Dell(conf)#radius-server host 10.11.197.105 timeout 6 Dell(conf)#radius-server host 10.11.197.105 retransmit 4 Dell(conf)#interface gigabitethernet 2/23 Dell(conf-if-gi-2/23)#dot1x server-timeout 40 dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out.
PAGE 164
dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. S6000 Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 165
mac-address • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/port information. • For a Ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. (Optional) MAC address of an 802.1X-authenticated supplicant. Defaults none Command Modes • EXEC • EXEC privilege Command History This guide is platform-specific.
PAGE 166
Dell#show dot1x cos-mapping int g 2/21 mac-address 00:00:01:00:07:00 802.1p CoS re-map table on Gi 2/21: ---------------------------------802.1p CoS re-map table for Supplicant: 00:00:01:00:07:00 Dot1 Remapped Dot1p 0 7 1 6 2 5 3 4 4 3 5 2 6 1 7 0 show dot1x interface Display the 802.1X configuration of an interface.
PAGE 167
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Added the mac-address option on the C-Series and SSeries. Version 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. Usage Information If you enable 802.1X multi-supplicant authentication on a port, additional 802.
PAGE 168
Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 60 seconds 1 30 seconds 30 seconds 60 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:01:00:07:00 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: Dell# Example (Interface) AUTHORIZED(MAC-AUTH-BYPASS) 4094 Authenticated Idle Dell#show dot1x interface g 0/21 802.
PAGE 169
Access Control Lists (ACL) 6 Access control lists (ACLs) are supported by the Dell Networking operating software on the S6000 platform.
PAGE 170
description Enter a description of up to 80 characters. Defaults Not configured. Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 171
show config Display the current ACL configuration. S6000 Syntax show config Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST Command History • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 172
NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line. S6000 Syntax access-class access-list-name To remove an ACL, use the no access-class access-list-name command. Parameters access-listname Enter the name of a configured Standard ACL, up to 140 characters. Defaults Not configured. Command Modes LINE Command History This guide is platform-specific.
PAGE 173
Parameters access-listname (OPTIONAL) Enter the name of a configured access-list, up to 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 174
implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). vlan vlan-id (OPTIONAL) Enter the keyword vlan then the ID numbers of the VLANs. The range is from 1 to 4094 (you can use IDs from 1 to 4094). vrf vrf-name (OPTIONAL) Enter the keyword vrf then the ID numbers of the VRFs. The range is from 1 to 63 (you can use IDs from 1 to 63). NOTE: When you specify a single VRF, use the name of the VRF instead of the VRF ID number.
PAGE 175
Use the vrf attribute of this command to associate an access-list to a non-default VRF. You can use this command at the interface context (physical/LAG) to apply the access-list to a range of VRFs. The VRF MODE is not available for the default and management VRFs. Related Commands ip access-list standard — configures a standard ACL. ip access-list extended — configures an extended ACL. ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic.
PAGE 176
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. in | out Identify whether ACL is applied on the ingress or egress side. vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to view the IP accounting information on either a default or a non-default VRF.
PAGE 177
seq seq seq seq seq 5 deny ip any 191.1.0.0 /16 count (0x00 packets) 10 deny ip any 191.2.0.0 /16 order 4 15 deny ip any 191.3.0.0 /16 20 deny ip any 191.4.0.0 /16 25 deny ip any 191.5.0.0 /16 Dell#show ip accounting access-list L3-ACL vrf vrf3 ! Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1.2.0/24 seq 10 permit 20.1.2.0/24 seq 15 permit 30.1.2.
PAGE 178
• • • host ip-address dscp — Enter the keyword dcsp followed by the DCSP value to match to the IP DCSCP values. The range is from 0 to 63. fragments — Enter the keyword fragments to use ACLs to control packet fragments. order — Enter the keyword order to specify the QoS order of priority for the ACL entry. The range is from 0 to 254 (0 is the highest priority and 254 is the lowest; lowerorder numbers have a higher priority).
PAGE 179
Related Commands ip access-list standard — configures a standard ACL. permit — configures a permit filter. ip access-list standard Create a standard IP access list (IP ACL) to filter based on IP address. S6000 Syntax ip access-list standard access-list-name To delete an access list, use the no ip access-list standard accesslist-name command. Parameters access-listname Enter a string up to 140 characters long as the ACL name.
PAGE 180
Usage Information Dell Networking OS supports one ingress and one egress IP ACL per interface. Prior to Dell Networking OS version 7.8.1.0, names are up to 16 characters long. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation. Example Dell(conf)#ip access-list standard TestList Dell(config-std-nacl)# Related Commands ip access-list extended — creates an extended access list.
PAGE 181
not use the keyword order, the ACLs have the lowest order by default (255). host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname. Defaults Not configured. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 182
resequence access-list Re-assign sequence numbers to entries of an existing access-list. S6000 Syntax Parameters resequence access-list {ipv4 | ipv6 | mac} {access-list-name StartingSeqNum Stepto-Increment} ipv4 | ipv6 | mac Enter the keyword ipv4or mac to identify the access list type to resequence. access-listname Enter the name of a configured IP access list. StartingSeqNu m Enter the starting sequence number to resequence. The range is from 0 to 4294967290.
PAGE 183
Usage Information When you have exhausted all the sequence numbers, this feature permits reassigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. S6000 Syntax seq sequence-number {deny | permit} {source [mask] | any | host ip-address}} [count [bytes]] [dscp value] [order] [fragments] To delete a filter, use the no seq sequence-number command.
PAGE 184
Defaults Not configured Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.
PAGE 185
Extended IP ACL Commands When an ACL is created without any rule and then applied to an interface, ACL behavior reflects an implicit permit. The following commands configure extended IP ACLs, which in addition to the IP address, also examine the packet’s protocol type. The supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny Configure a filter that drops IP packets meeting the filter criteria.
PAGE 186
byte (OPTIONAL) Enter the keyword byte to count bytes that the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority).
PAGE 187
Version 6.5.1.0 Usage Information Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the Quality of Service chapter of the Dell Networking OS Configuration Guide. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 188
any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. dscp Enter this keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. count (OPTIONAL) Enter the keyword count to count packets processed by the filter.
PAGE 189
Version 6.5.1.0 Usage Information Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the Quality of Service chapter of the Dell Networking OS Configuration Guide. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to the Port Monitoring chapter. When you use the log option, the CP processor logs details the packets that match.
PAGE 190
operator port port • rst: reset the connection • syn: synchronize sequence numbers • urg: urgent field (OPTIONAL) Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command) Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is from 0 to 65535.
PAGE 191
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 192
range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range. Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 193
any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. dscp Enter this keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63.
PAGE 194
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Added the keyword dscp. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 195
5 6 7 8 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 7168 7680 7936 8000 7679 7935 7999 8000 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands deny — assigns a filter to deny IP traffic.
PAGE 196
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification on entries allowed per ACL, refer to your line card documentation.
PAGE 197
destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. bytes (OPTIONAL) Enter the keyword bytes to count bytes processed by the filter. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 198
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. The software cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. Related Commands ip access-list extended — creates an extended ACL. permit tcp — assigns a permit filter for TCP packets. permit udp — assigns a permit filter for UDP packets.
PAGE 199
• urg: urgent field dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. operator (OPTIONAL) Enter one of the following logical operand: port port • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 200
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Added the keyword dscp. Version 8.2.1.
PAGE 201
Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 202
host ip-address Enter the keyword host and then enter the IP address to specify a host IP address. dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. operator (OPTIONAL) Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter the application layer port number.
PAGE 203
Usage Information Version 8.3.1.0 Added the keyword dscp. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added support for non-contiguous mask and added the monitor option. . Version 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 204
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands ip access-list extended — creates an extended ACL. permit — assigns a permit filter for IP packets. permit tcp — assigns a permit filter for TCP packets. resequence access-list Re-assign sequence numbers to entries of an existing access-list.
PAGE 205
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. When all sequence numbers have been exhausted, this feature permits reassigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 206
operator port port (OPTIONAL) Enter one of the following logical operands: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter.) (OPTIONAL) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 207
fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 208
When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. If you configure the sequence-number, the sequence-number is used as a tie breaker for rules with the same order. NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead.
PAGE 209
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. mac access-group Apply a MAC ACL to traffic entering or exiting an interface. The following interface types can be used for VLAN , Physical interface, Port channel interface.
PAGE 210
NOTE: 1. If the MAC ACL is applied on VLAN, none of the VLAN members should have an access list applied for that VLAN. 2. If the MAC ACL is applied on a Physical or Port Channel interface, the VLAN in which this port is associated should not have an access list applied. 3. If the MAC ACL is applied on a VLAN, then that VLAN should not belong to VLAN ACL group. 4. If the MAC ACL is applied on a VLAN ACL group, then none of the VLANs in that group should have an access list applied on it.
PAGE 211
show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed. S6000 Syntax Parameters show mac access-lists [access-list-name] [interface interface] [in | out] access-listname Enter the name of a configured MAC ACL, up to 140 characters.
PAGE 212
show mac accounting access-list Display MAC access list configurations and counters (if configured). S6000 Syntax Parameters show mac accounting access-list access-list-name interface interface in | out access-listname Enter the name of a configured MAC ACL, up to 140 characters. interface interface Enter the keyword interface then the one of the following keywords and slot/port or number information: in | out • For a Port Channel interface, enter the keyword portchannel and then enter a number.
PAGE 213
Version 7.5.1.0 Introduced on the C-Series pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information The ACL hit counters in this command increment the counters for each matching rule, not just the first matching rule.
PAGE 214
• Parameters Use the no deny {any | mac-source-address mac-source-addressmask} command. any Enter the keyword any to specify that all routes are subject to the filter. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match).
PAGE 215
Usage Information When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands permit — configures a MAC address filter to pass packets.
PAGE 216
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Dell Networking OS supports one ingress and one egress MAC ACL per interface. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation. NOTE: Ingress ACLs are supported on C-Series and S-Series platforms only.
PAGE 217
log (OPTIONAL, E-Series only) Enter the keyword log to log the packets. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, refer to the Flow-based Monitoring section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Defaults Not configured.
PAGE 218
seq To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. S6000 Syntax seq sequence-number {deny | permit} {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log] [monitor] To remove this filter, use the no seq sequence-number command. Parameters sequencenumber Enter a number from 0 to 65535. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.
PAGE 219
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the monitor option. pre-Version 6.1.1.
PAGE 220
mac-destination-address-mask} [ethertype-operator] [count [byte]] [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | macdestination-address mac-destination-address-mask} command. any Enter the keyword any to drop all packets.
PAGE 221
interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 222
To delete a MAC access list, use the no mac access-list extended accesslist-name command. Parameters access-listname Enter a text string as the MAC access list name, up to 140 characters. cpu-qos Enter the keywords cpu-qos to assign this ACL to control plane traffic only (CoPP). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 223
Dell(config-ext-macl)#exit Dell(conf)#do show mac accounting access-list snickers interface g0/47 in Extended mac access-list snickers on GigabitEthernet 0/47 seq 10 permit any any ev2 eq 800 count bytes (559851886 packets 191402152148 bytes) seq 20 permit any any ev2 eq 806 count bytes (74481486 packets 5031686754 bytes) seq 30 permit any any ev2 eq 86dd count bytes (7751519 packets 797843521 bytes) Related Commands mac access-list standard — configures a standard MAC access list.
PAGE 224
macdestinationaddress Enter the destination MAC address and mask in nn:nn:nn:nn:nn:nn format. macdestinationaddress-mask Specify which bits in the MAC address must be matched. ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the following Ethertypes: The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly.
PAGE 225
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the monitor option. pre-Version 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 226
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increase the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.
PAGE 227
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Sequence numbers for this filter are automatically assigned starting at sequence number 5.
PAGE 228
Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information Prefix lists redistribute OSPF and RIP routes meeting specific criteria. Related Commands show ip route list — displays IP routes in an IP prefix list.
PAGE 229
bitmask number Enter the keyword bitmask then enter a bit mask number in dotted decimal format. Defaults Not configured. Command Modes PREFIX-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 230
Example Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Dell(conf-nprefixl)#show config ! ip prefix-list snickers Dell(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists.
PAGE 231
pre-Version 6.1.1.0 Example Introduced on the E-Series. Dell#show ip prefix-list detail Prefix-list with the last deletion/insertion: filter_ospf ip prefix-list filter_in: count: 3, range entries: 3, sequences: 5 - 10 seq 5 deny 1.102.0.0/16 le 32 (hit count: 0) seq 6 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 10 permit 0.0.0.0/0 le 32 (hit count: 0) ip prefix-list filter_ospf: count: 4, range entries: 1, sequences: 5 - 10 seq 5 deny 100.100.1.0/24 (hit count: 5) seq 6 deny 200.200.1.
PAGE 232
pre-Version 6.1.1.0 Example Introduced on the E-Series.
PAGE 233
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. The continue feature allows movement from one route-map entry to a specific route-map entry (the sequence number).
PAGE 234
description Add a description to this route map. S6000 Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the route map (80 characters maximum). Defaults none Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 235
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.
PAGE 236
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.
PAGE 237
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.
PAGE 238
Parameters prefix-listname Enter the name of configured prefix list, up to 140 characters. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 239
match ip next-hop To match based on the next-hop IP addresses specified in an IP access list or IP prefix list, configure a filter. S6000 Syntax match ip next-hop {prefix-list prefix-list-name} To delete a match, use the no match ip next-hop {prefix-list prefixlist-name} command. Parameters prefix-list prefix-listname Enter the keywords prefix-list and then enter the name of configured prefix list, up 10 140 characters. Defaults Not configured.
PAGE 240
match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match ip route-source To match based on the routes advertised by routes specified in IP access lists or IP prefix lists, configure a filter. S6000 Syntax match ip route-source {prefix-list prefix-list-name} To delete a match, use the no match ip route-source {prefix-list prefix-list-name} command.
PAGE 241
match ip next-hop — redistributes routes that match the next-hop IP address. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match metric To match on a specified value, configure a filter. S6000 Syntax match metric metric-value To delete a value, use the no match metric [metric-value] command. Parameters metric-value Enter a value to match.
PAGE 242
match ip route-source — redistributes routes that match routes advertised by other routers. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match origin To match routes based on the value found in the BGP path ORIGIN attribute, configure a filter. S6000 Syntax match origin {egp | igp | incomplete} To disable matching filter, use the no match origin {igp | egp | incomplete} command.
PAGE 243
match route-type To match routes based on the how the route is defined, configure a filter. S6000 Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command. Parameters external [type-1| type-2] Enter the keyword external then either type-1 or type-2 to match only on OSPF Type 1 routes or OSPF Type 2 routes.
PAGE 244
match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match tag — redistributes routes that match a specific tag. match tag To redistribute only routes that match a specified tag value, configure a filter. S6000 Syntax match tag tag-value To remove a match, use the no match tag command.
PAGE 245
match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. route-map Enable a route map statement and configure its action and sequence number. This command also places you in ROUTE-MAP mode.
PAGE 246
Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 247
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. You can prepend up to eight AS numbers to a BGP route. This command influences best path selection in BGP by inserting a tag or AS number into the AS_PATH attribute.
PAGE 248
pre-Version 6.1.1.0 Related Commands Introduced on the E-Series. set level — specify the OSPF area for route redistribution. set metric — specify the metric value assigned to redistributed routes. set metric-type — specify the metric type assigned to redistributed routes. set tag — specify the tag assigned to redistributed routes. set comm-list delete To remove the specified community list from the BGP route’s COMMUNITY attribute, configure a filter.
PAGE 249
pre-Version 6.1.1.0 Usage Information Introduced on the E-Series. The community list used in the set comm-list delete command must be configured so that each filter contains only one community. For example, the filter deny 100:12 is acceptable, but the filter deny 120:13 140:33 results in an error.
PAGE 250
All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. none Enter the keyword none to remove the community attribute from routes meeting the route map criteria. additive (OPTIONAL) Enter the keyword additive to add the communities to already existing communities. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 251
level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 252
To delete a BGP LOCAL_PREF attribute, use the no set local-preference command. Parameters value Enter a number as the LOCAL_PREF attribute value. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 253
- (OPTIONAL) Enter - to subtract a metric-value from the redistributed routes. metric-value Enter a number as the new metric value. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.
PAGE 254
external Enter the keyword external to assign the IS-IS external metric. type-1 Enter the keyword type-1 to assign the OSPF Type 1 metric. type-2 Enter the keyword type-2 to assign the OSPF Type 2 metric. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 255
Parameters ip-address Specify an IP address in dotted decimal format. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 256
incomplete Enter the keyword incomplete to set routes with incomplete routing information. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 257
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. set automatic-tag — computes the tag value of the route. set level — specifies the OSPF area for route redistribution.
PAGE 258
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 259
route-map hopper permit 10 Dell(config-route-map)# show route-map Display the current route map configurations. S6000 Syntax Parameters show route-map [map-name] map-name (OPTIONAL) Enter the name of a configured route map, up to 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 260
deny (for Standard IP ACLs) To drop packets with a certain IP address, configure a filter. Syntax deny {source | any | host {ip-address}}[count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Defaults Use the no seq sequence-number command if you know the filter’s sequence number. Use the no deny {source [mask] | any | host ip-address} command.
PAGE 261
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 262
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.
PAGE 263
seq (for Standard IPv4 ACLs) Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ip-address}} [count [bytes]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To delete a filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 264
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 265
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.
PAGE 266
address-mask | any} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny ether-type protocol-type-number {destinationmac-address mac-address-mask | any} vlan vlan-id {sourcemac-address mac-address-mask | any} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 267
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
PAGE 268
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-MAC ACCESS LIST-STANDARD Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 269
[byte]][log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | macdestination-address mac-destination-address-mask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 270
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
PAGE 271
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.
PAGE 272
permit arp (for Extended MAC ACLs) Configure a filter that forwards ARP packets meeting this criteria. This command is supported only on 12port GE line cards with SFP optics; refer to your line card documentation for specifications.
PAGE 273
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 274
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.
PAGE 275
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 276
ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 277
Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 278
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 279
enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
PAGE 280
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command History Usage Information Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 281
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 282
one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands deny — configures a filter to drop packets. permit — configures a filter to forward packets. permit tcp (for Extended IP ACLs) To pass TCP packets meeting the filter criteria, configure a filter.
PAGE 283
Command History Usage Information Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 284
| opcode code-number} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated.
PAGE 285
egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 286
Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 287
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 288
Related Commands deny — configures a filter to drop packets. permit — configures a filter to forward packets. seq (for IPv6 ACLs) Assign a sequence number to a deny or permit the filter in an IPv6 access list while creating the filter.
PAGE 289
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 290
of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 291
permit tcp (for IPv6 ACLs) Configure a filter to pass TCP packets that match the filter criteria. Syntax permit tcp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6address} [bit] [operator port [port]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 292
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 293
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version 9.4(0.
PAGE 294
To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 295
ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 296
Command History Usage Information Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 297
• Parameters Defaults Use the no deny arp {destination-mac-address mac-address-mask | any} vlan vlan-id {ip-address | any | opcode code-number} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands.
PAGE 298
ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 299
Command History Usage Information Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 300
• Parameters Defaults Use the no deny icmp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 301
particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). deny (for IPv6 ACLs) Configure a filter that drops IPv6 packets that match the filter criteria.
PAGE 302
Version 9.4(0.0) Usage Information Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 303
7 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection. The Dell Networking operating software implementation is based on the standards specified in the IETF Draft draft-ietf-bfd-base-03 and supports BFD on all Layer 3 physical interfaces including VLAN interfaces and port-channels BFD is supported on the S6000 platform.
PAGE 304
The default is active. Defaults Refer to Parameters. Command Modes ROUTER OSPF ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.2. (0.
PAGE 305
Related Commands neighbor bfd disable — Explicitly disables a BFD session with a BGP neighbor or a BGP peer group. ip route bfd Enable BFD for all neighbors configured through static routes. S6000 Syntax ip route bfd [interval interval min_rx min_rx multiplier value role {active | passive}] To disable BFD for all neighbors configured through static routes, use the no ip route bfd [interval interval min_rx min_rx multiplier value role {active | passive}] command.
PAGE 306
Version 9.2. (0.0) Introduced on Z9000, S4810, and S4820T. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. neighbor bfd Explicitly enable a BFD session with a BGP neighbor or a BGP peer group. S6000 Syntax Parameters neighbor {ip-address | peer-group-name} bfd ip-address Enter the IP address of the BGP neighbor that you want to explicitly enable for BFD sessions in dotted decimal format (A.B.C.D).
PAGE 307
When you explicitly enable a BGP neighbor for a BFD session with the bfd neighbor command: Related Commands • The neighbor does not inherit the global BFD enable values configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs. • The neighbor only inherits the global timer values configured with the bfd neighbor command: interval, min_rx, and multiplier. neighbor bfd disable — Explicitly disables a BFD session with a BGP neighbor or a BGP peer group.
PAGE 308
• The neighbor does not inherit the global BFD disable values configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs. • The neighbor only inherits the global timer values configured with the bfd neighbor command: interval, min_rx, and multiplier.
PAGE 309
Boot Command Line Interface 8 BCLI commands are supported on the S6000 platform only. S6000 To access this BOOT_USER mode, first boot your Dell Networking platform. When you see the “Press ESC to stop auto-boot”, press the ESC key to log into BCLI You enter BOOT_USER mode immediately, as indicated by the BOOT_USER# prompt. NOTE: All commands in this chapter are in Boot_User mode. These commands are supported on the Dell Networking platform. You cannot use the Tab key to complete commands in this mode.
PAGE 310
Command Modes Command History Usage Information BOOT_USER Version 9.0.2.0 Introduced on the S6000. After entering the boot change command and selecting the parameters, press Enter. The software prompts you to enter the following: • The boot device (flash, ftp, tftp, or usbflash), image file name, IP address of the server containing the image, username, and password (only for ftp).
PAGE 311
boot message Use this command to enable/disable boot logs during reload. S6000 Syntax Parameters boot message on | off on Enter the keyword on to turn on boot logs during reload. off Enter the keyword off to suppress the boot logs during reload. NOTE: By default, watchdog is disabled. Defaults None Command Modes BOOT_USER Command History Example Version 9.0.2.0 Introduced on the S6000.
PAGE 312
boot write net config retries Set the number of retries for network boot configuration failure. S6000 Syntax boot write net config retries Command Modes BOOT_USER Command History Example Version 9.0.2.0 Introduced on the S6000. BOOT_USER # boot write net config retries 2 Updated number of Network Boot Config retries to 2 BOOT_USER # boot zero Erase the configured primary, secondary, or default boot image parameters.
PAGE 313
Usage Information This command reverses changes made with the boot change command.
PAGE 314
Command History Version 9.0.2.0 Introduced on the S6000. Usage Information Use the show default-gateway command to view the current default gateway. Related Commands show_default-gateway— Change the primary, secondary, or default boot image configuration. etheraddr Assign the management port MAC address. S6000 Syntax Parameters Command Modes Command History etheraddr mac-address Enter a MAC address in standard format. BOOT_ADMIN Version 9.0.2.0 Introduced on the S6000.
PAGE 315
Command History Usage Information Version 9.0.2.0 Introduced on the S6000. When you enter the reload command and the system reboots, you will not be prompted for a password to enter the EXEC Privilege mode (normally you are required to enter the enable command). If your console or Telnet session expires after you used the ignore enablepassword command, you are prompted for an enable password when you reestablish the session Related Commands reload — Exit from this mode and reload FTOS.
PAGE 316
Command Modes Command History Usage Information BOOT_USER Version 9.0.2.0 Introduced on the S6000. In the runtime CLI, use the ip address command in INTERFACE mode to change the Management interface’s IP address. To view the current IP address configured on the Management interface, enter the show interfaces management ethernet command Related Commands show_default-gateway — Display the IP address configured for the default gateway.
PAGE 317
reload Exit from this mode and reload Dell Networking OS. S6000 Syntax reload Command Modes BOOT_USER Command History Version 9.0.2.0 Introduced on the S6000. serial console Use the serial console to set the serial console baud rate. S6000 Syntax Parameters serial console serial console [unit] [baud] Enter the keyword to set the serial port baud rate. The supported values for serial console: • Unit - 0 • Baud rate -9600,115200 No defaults.
PAGE 318
show bootvar Display boot configuration information. S6000 Syntax show bootvar Command Modes BOOT_USER Command History Example Version 9.0.2.0 Introduced on the S6000.
PAGE 319
show default-gateway Display the IP address configured for the default gateway. S6000 Syntax show default-gateway Command Modes BOOT_USER Command History Example Version 9.0.2.0 Introduced on the S6000. BOOT_USER # show default-gateway Gateway IP address: 10.16.100.254 BOOT_USER # Related Commands default-gateway— Configure the IP address for the default gateway. interface_management_ethernet_ip_address — Assign an IP address to the Management Ethernet interface.
PAGE 320
Related Commands interface_management_ethernet_ip_address — Assign an IP address to the Management Ethernet interface. reload — Configure speed, duplex, and negotiation settings for the management interface. show serial console baud rate Use the show serial console to show the values of the serial console baud rate. S6000 Syntax show serial console baudrate Command Modes BOOT_USER Command History Example Version 9.0.2.0 Introduced on the S6000.
PAGE 321
NOTE: By default, watchdog is disabled. Command Modes Command History Example BOOT_ADMIN Version 9.0.2.0 Introduced on the S6000.
PAGE 322
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables. BGP is supported in Dell Networking OS version 9.0.2.
PAGE 323
ipv4 vrf vrfname Enter the keyword ipv4 followed by the keyword vrf and then the name of the VRF to enable VRF mode. NOTE: Use this attribute to start a BGP instance corresponding to either a specific address family in a default VRF or an IPv4 address family in a non-default VRF. ipv6 unicast Enter the keyword ipv6 followed by the keyword unicast to enable BGPv6 mode. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 324
as-set (OPTIONAL) Enter the keyword as-set to generate path attribute information and include it in the aggregate. AS_SET includes AS_PATH and community information from the routes included in the aggregated route. Defaults Command Modes Command History attribute-map map-name (OPTIONAL) Enter the keywords attribute-map then the name of a configured route map to modify attributes of the aggregate, excluding AS_PATH and NEXT_HOP attributes.
PAGE 325
If the route is injected via the network command, that route still appears in the routing table if the summary-only parameter is configured in the aggregateaddress command. The summary-only parameter suppresses all advertisements. If you want to suppress advertisements to only specific neighbors, use the neighbor distribute-list command. In the show ip bgp command, aggregates contain an ‘a’ in the first column and routes suppressed by the aggregate contain an ‘s’ in the first column.
PAGE 326
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.0 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. neighbor add-path — specifies that this neighbor/peer group can send/receive multiple path advertisements. bgp always-compare-med Allows you to enable comparison of the MULTI_EXIT_DISC (MED) attributes in the paths from different external ASs. S6000 Syntax bgp always-compare-med To disable comparison of MED, enter no bgp always-compare-med.
PAGE 327
bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI). S6000 Syntax bgp asnotation [asplain | asdot+ | asdot] To disable a dot or dot+ representation and return to ASPLAIN, enter the no bgp asnotation command. Defaults asplain Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 328
router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ Dell(conf)#router bgp 1 Dell(conf-router_bgp)#bgp asnotation asplain Dell(conf-router_bgp)#ex Dell(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support Dell(conf)# Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations.
PAGE 329
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. S6000 Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath aspath multipath-relax command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 330
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 331
Usage Information Version 7.7.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced The MED is a 4-byte unsigned integer value and the default behavior is to assume a missing MED as 4294967295. This command causes a missing MED to be treated as 0. During path selection, paths with a lower MED are preferred over paths with a higher MED. bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection.
PAGE 332
Defaults Enabled when a route reflector is configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 333
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors.
PAGE 334
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 335
bgp confederation peers Specify the autonomous systems (ASs) that belong to the BGP confederation. S6000 Syntax bgp confederation peers as-number [...as-number] To return to the default, use the no bgp confederation peers command. Parameters as-number Enter the AS number. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). ...as-number (OPTIONAL) Enter up to 16 confederation numbers.
PAGE 336
Related Commands bgp confederation identifier — configures a confederation ID. bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp dampening Enable BGP route dampening and configure the dampening parameters. S6000 Syntax bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] To disable route dampening, use the no bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] command.
PAGE 337
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 338
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 339
Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. This command is enabled by default, that is for all updates received from EBGP peers, BGP ensures that the first AS of the first AS segment is always the AS of the peer. If not, the update is dropped and a counter is increments. Use the show ip bgp neighbors command to view the “failed enforce-first-as check” counter.
PAGE 340
Version 7.7.1.0 Usage Information Introduced on the C-Series. The bgp fast-external-fallover command appears in the show config command output. The fast external fallover configuration is applied only after you manually reset all the existing BGP sessions. As a result, after you execute this command, you must also manually execute the clear ip bgp command in order for the configuration to take effect. bgp four-octet-as-support Enable 4-byte support for the BGP process.
PAGE 341
Where the 2-byte format is from 1 to 65535, the 4-byte format is from 1 to 4294967295. Both formats are accepted and the advertisements reflect the entered format. For more information about using the 2 byte or 4-byte format, refer to the Dell Networking OS Configuration Guide. This command automatically restarts the BGP instance for the configuration to take effect.
PAGE 342
Version 7.7.1.0 Usage Information Introduced on the C-Series. This feature is advertised to BGP neighbors through a capability advertisement. In Receiver Only mode, BGP saves the advertised routes of peers that support this capability when they restart. BGP graceful restart is active only when the neighbor becomes established. Otherwise it is disabled. Graceful-restart applies to all neighbors with established adjacency.
PAGE 343
compares MED between adjacent paths within an AS group because all paths in the AS group are from the same AS. When you change the path selection from Deterministic to Non-Deterministic, the path selection for the existing paths remains Deterministic until you enter the clear ip bgp command to clear existing paths. bgp recursive-bgp-next-hop Enable next-hop resolution through other routes learned by BGP.
PAGE 344
Related Commands clear ip bgp — clears the ip bgp. bgp regex-eval-optz-disable Disables the Regex Performance engine that optimizes complex regular expression with BGP. S6000 Syntax bgp regex-eval-optz-disable To re-enable optimization engine, use the no bgp regex-eval-optz-disable command. Defaults Enabled Command Modes ROUTER BGP (conf-router_bgp) Command History This guide is platform-specific.
PAGE 345
Examples Dell(conf-router_bgp)#no bgp regex-eval-optz-disable Dell(conf-router_bgp)#do show ip protocols Routing Protocol is "ospf 22222" Router ID is 2.2.2.2 Area Routing for Networks 51 10.10.10.0/00 Routing Protocol is "bgp 1" Cluster Id is set to 10.10.10.0 Router Id is set to 10.10.10.
PAGE 346
Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection.
PAGE 347
NOTE: You must execute the clear ip bgp soft out command when ever there is a change in the local policy. If you do not run this command after a local policy change, then these policy changes are not reflected in the responses to the peer’s route refresh messages. <1-429496729 5> Enter <1-4294967295> to clear peers with the AS number. <0.1-65535.65 535> Enter <0.1-65535.65535> to clear peers with the AS number in dot format. A.B.C.D Enter the BGP neighbor address in the A.B.C.D format to clear.
PAGE 348
Related Commands bgp recursive-bgp-next-hop — disables next-hop resolution through other routes learned by the BGP. clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state.
PAGE 349
clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap. S6000 Syntax Parameters clear ip bgp [vrf vrf-name] flap-statistics [ip-address mask | filter-list as-path-name | regexp regular-expression] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear BGP flap statistics corresponding to that VRF. NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF.
PAGE 350
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 351
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Added support for VRF. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 352
events Enter the keyword events to view BGP protocol events. ipv4 Enter the ipv4 IP address to view the IPV4 route information. ipv6 Enter the ipv6 IP address to view the IPV6 route information. keepalives Enter the keyword keepalives to view BGP keepalives. notifications Enter the keyword notifications to view BGP notifications. softreconfiguration Enter the keywords soft-reconfiguration to view only information on inbound BGP soft reconfiguration.
PAGE 353
show debugging — views enabled debugging operations. debug ip bgp dampening View information on routes being dampened. S6000 Syntax debug ip bgp [vrf test | ipv4 {unicast | multicast} | ipv6 {unicast | multicast} dampening To disable debugging, use the no debug ip bgp ipv4 multicast dampening command. Parameters dampening Enter the keyword dampening to debug route flap dampening information. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 354
Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group peer-groupname (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only events on inbound BGP messages. out (OPTIONAL) Enter the keyword out to view only events on outbound BGP messages. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 355
peer-group peer-groupname (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only inbound keepalive messages. out (OPTIONAL) Enter the keyword out to view only outbound keepalive messages. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 356
in (OPTIONAL) Enter the keyword in to view BGP notifications received from neighbors. out (OPTIONAL) Enter the keyword out to view BGP notifications sent to neighbors Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 357
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 358
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 359
Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage Information The default-metric command in BGP sets the value of the BGP MULTI_EXIT_DISC (MED) attribute for redistributed routes only. Related Commands bgp always-compare-med — enables comparison of all BGP MED attributes. redistribute — redistributes routes from other routing protocols into BGP.
PAGE 360
max-paths Configure the maximum number of parallel routes (multipath support) BGP supports. S6000 Syntax max-paths {ebgp | ibgp} number To return to the default values, enter the no maximum-paths command. Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipath support for Internal BGP routes. number Enter a number as the maximum number of parallel paths.
PAGE 361
neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/Subsequent Address Family Identifier). S6000 Syntax neighbor [ip-address | peer-group-name] activate To disable, use the no neighbor [ip-address | peer-group-name] activate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname (OPTIONAL) Enter the name of the peer group.
PAGE 362
neighbor add-path This command allows the specified neighbor/peer group to send/receive multiple path advertisements. S6000 Syntax Parameters neighbor [ip-address | peer-group-name] add-path [send | receive | both] path-count ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname (OPTIONAL) Enter the name of the peer group. send Enter the keyword send to indicate that the system sends multiple paths to peers.
PAGE 363
neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. S6000 Syntax neighbor {ip-address | peer-group-name} advertisement-interval seconds To return to the default value, use the no neighbor {ip-address | peergroup-name} advertisement-interval command. Parameters Defaults ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format.
PAGE 364
neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting. S6000 Syntax neighbor {ip-address} advertisement-start seconds To return to the default value, use the no neighbor {ip-address} advertisement-start command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. seconds Enter a number as the time interval, in seconds, before BGP route updates are sent. The range is from 0 to 3600 seconds.
PAGE 365
peer-groupname Enter the name of the peer group to set the advertisement interval for all routers in the peer group. number Enter a number of times to allow this neighbor ID to use the AS path. The range is from 1 to 10. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 366
route-map map-name (OPTIONAL) Enter the keyword route-map then the name of a configured route map. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 367
neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). S6000 Syntax neighbor {ip-address | peer-group-name} description text To delete a description, use the no neighbor {ip-address | peer-groupname} description command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group. text Enter a continuous text string up to 80 characters. Defaults Not configured.
PAGE 368
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to apply the distribute list filter to all routers in the peer group. prefix-listname Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes). in Enter the keyword in to distribute only inbound traffic. out Enter the keyword out to distribute only outbound traffic. Defaults Not configured.
PAGE 369
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group. ttl (OPTIONAL) Enter the number of hops as the Time to Live (ttl) value. The range is from 1 to 255. The default is 255. Defaults Disabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 370
Defaults Disabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 371
no prepend Specifies that local AS values do not prepend to announcements from the neighbor. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 372
maximum Enter a number as the maximum number of prefixes allowed for this BGP router. The range is from 1 to 4294967295. threshold (OPTIONAL) Enter a number to be used as a percentage of the maximum value. When the number of prefixes reaches this percentage of the maximum value, the E-Series software sends a message. The range is from 1 to 100 percent. The default is 75. warning-only (OPTIONAL) Enter the keyword warning-only to set the router to send a log message when the maximum value is reached.
PAGE 373
neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors. S6000 Syntax neighbor {ip-address | peer-group-name} password [encryptiontype] password To delete a password, use the no neighbor {ip-address | peer-groupname} password command. Parameters ip-address Enter the IP address of the router to be included in the peer group. peer-groupname Enter the name of a configured peer group.
PAGE 374
of the TCP connection between them is verified and the MD5 digest is checked on every segment sent on the TCP connection. Configuring a password for a neighbor causes an existing session to be torn down and a new one established. If you specify a BGP peer group by using the peer-group-name parameter, all the members of the peer group inherit the characteristic configured with this command.
PAGE 375
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. You can assign up to 256 peers to one peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
PAGE 376
Parameters peer-groupname Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 377
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.
PAGE 378
peer-groupname Enter the name of the peer group to enter the remote AS into routing tables of all routers within the peer group. number Enter a number of the AS. The range is from 0 to 65535 (2 byte) or from 1 to 4294967295 (4 byte). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 379
Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers. peer-groupname Enter the name of the peer group to remove the private AS numbers. Defaults Disabled (that is, private AS number are not removed). Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 380
To remove the route map, use the no neighbor {ip-address | peergroup-name} route-map map-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group. map-name Enter the name of an established route map. If the Route map is not configured, the default is deny (to drop all routes). in Enter the keyword in to filter inbound routes. out Enter the keyword out to filter outbound routes.
PAGE 381
neighbor route-reflector-client Configure the router as a route reflector and the specified neighbors as members of the cluster. S6000 Syntax neighbor {ip-address | peer-group-name} route-reflector-client To remove one or more neighbors from a cluster, use the no neighbor {ipaddress | peer-group-name} route-reflector-client command. If you delete all members of a cluster, you also delete the route-reflector configuration on the router.
PAGE 382
When you remove all clients of a route reflector using the no neighbor routereflector-client command, the router no longer functions as a route reflector. If the clients of a route reflector are fully meshed, you can configure the route reflector to not reflect routes to specified clients by using the no bgp clientto-client reflection command. This command automatically restarts the neighbor session for the configuration to take effect.
PAGE 383
Usage Information Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group. Use this command with caution as it terminates the specified BGP sessions. When a neighbor or peer group is shut down, use the show ip bgp summary command to confirm its status. Related Commands show ip bgp summary — displays the current BGP configuration.
PAGE 384
Version 7.4.1.0 Usage Information Introduced. This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. CAUTION: Inbound update storage is a memory-intensive operation.
PAGE 385
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 386
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 387
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. In the Dell Networking OS best path selection process, the path with the highest weight value is preferred.
PAGE 388
• match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 389
Related Commands redistribute — redistributes routes into BGP. network backdoor Specify this IGP route as the preferred route. S6000 Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for example, /24). The mask appears in command outputs in dotted decimal format (A.B.C.D).
PAGE 390
redistribute Redistribute routes into BGP. S6000 Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command. Parameters connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. These routes are treated as incomplete routes.
PAGE 391
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
PAGE 392
Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 | 2} (OPTIONAL) Enter the keywords match external to redistribute OSPF external routes. You can specify 1 or 2 to redistribute those routes only. match internal (OPTIONAL) Enter the keywords match internal to redistribute OSPF internal routes only. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Defaults Not configured.
PAGE 393
router bgp To configure and enable BGP, enter ROUTER BGP mode. S6000 Syntax router bgp as-number To disable BGP, use the no router bgp as-number command. Parameters as-number Enter the AS number. The range is from 1 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 394
show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system. S6000 Syntax Parameters show capture bgp-pdu neighbor ipv4-address ipv4-address Enter the IPv4 address (in dotted decimal format) of the BGP address to display packet information for that address. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 395
14141401 0c020a01 04000100 01020080 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:50 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] Dell# show config View the current ROUTER BGP configuration. S6000 Syntax show config Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 396
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view ipv4–unicast route information corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. network (OPTIONAL) Enter the network address (in dotted decimal format) of the BGP network to view information only on that network. network-mask (OPTIONAL) Enter the network mask (in slash prefix format) of the BGP network address.
PAGE 397
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 398
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 399
*>I 66.0.0.0/24 0 0 500 i *>I 77.0.0.0/24 0 0 i 172.16.0.2 172.16.0.2 Dell#show ip bgp cluster-list 4.4.4.4 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.6 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Weight Path *>I 55.0.0.0/24 172.16.0.
PAGE 400
no-advertise Enter the keywords no-advertise to view all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to view all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary.
PAGE 401
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 402
show ip bgp community-list View routes that a specific community list affects. S6000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] community-list community-list-name [exact-match] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes affected by a specific community list corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 403
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 404
Parameters Command Modes Command History vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 405
Example Field Description Path Lists all the ASs the dampened route passed through to reach the destination network. Dell#show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network d 55.0.0.
PAGE 406
bgpNdP 0x41a17000 : NdTmrP 0x41a17000 : NdKATmrP 0x41a17014 : NdTics 74857 : NhLocAS 1 : NdState 2 : NdRPMPrim 1 : NdListSoc 13 NdAuto 1 : NdEqCost 1 : NdSync 0 : NdDefOrg 0 NdV6ListSoc 14 NdDefDid 0 : NdConfedId 0 : NdMedConfed 0 : NdMedMissVal -1 : NdIgnrIllId 0 : NdRRC2C 1 : NdClstId 33686273 : NdPaTblP 0x41a19088 NdASPTblP 0x41a19090 : NdCommTblP 0x41a19098 : NhOptTransTblP 0x41a190a0 : NdRRClsTblP 0x41a190a8 NdPktPA 0 : NdLocCBP 0x41a6f000 : NdTmpPAP 0x419efc80 : NdTmpASPAP 0x41a25000 : NdTmpCommP 0x41
PAGE 407
AFIndex 0 NdSpFlag 0x41a190b0 : AFRttP 0x41a0d200 : NdRTMMkrP 0x41a19d28 : NdRTMAFTblVer 0 : NdRibCtxAddr 1101110688 NdRibCtxAddrLen 255 : NdAFPrefix 0 : NdAfNLRIP 0 : NdAFNLRILen 0 : NdAFWPtrP 0 NdAFWLen 0 : NdAfNH : NdAFRedRttP 0x41a0d400 : NdRecCtxAdd 1101110868 NdRedCtxAddrLen 255 : NdAfRedMkrP 0x41a19e88 : AFAggRttP 0x41a0d600 : AfAggCtxAddr 1101111028 : AfAggrCtxAddrLen 255 AfNumAggrPfx 0 : AfNumAggrASSet 0 : AfNumSuppmap 0 : AfNumAggrValidPfx 0 : AfMPathRttP 0x41a0d700 MpathCtxAddr 1101111140 : Mpath
PAGE 408
Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found.
PAGE 409
show ip bgp filter-list View the routes that match the filter lists. S6000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] filter-list as-pathname vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. as-path-name Enter an AS-PATH access list name.
PAGE 410
Field Example Description • c = external confederation route entry • n = network route entry • r = redistributed route entry Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight.
PAGE 411
ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. ip-address (OPTIONAL) Enter the IP address (in dotted decimal format) of the BGP network to view information only on that network. mask (OPTIONAL) Enter the network mask (in slash prefix (/x) format) of the BGP network address. filter-list aspath-name (OPTIONAL) Enter the keyword filter-list then the name of a configured AS-PATH ACL. The range is 140 characters.
PAGE 412
Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp flap command shown in the following example. Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route.
PAGE 413
show ip bgp inconsistent-as View routes with inconsistent originating autonomous system (AS) numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path. S6000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] inconsistent-as vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view routes corresponding to the VRF that contain inconsistent originating AS numbers.
PAGE 414
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. Dell>show ip bgp inconsistent-as BGP table version is 280852, local router ID is 10.1.2.100 Status codes: s suppressed, d damped, h history, * valid, > best Path source: I - internal, c - confed-external, r redistributed, n - network Origin codes: i - IGP, e - EGP, ? - incomplete Network Next * 3.
PAGE 415
*>n 66.66.66.77/32 *>n 66.66.77.77/32 0.0.0.0 0.0.0.0 0 0 32768 i 32768 i show ip bgp neighbors Allows you to view the information BGP neighbors exchange.
PAGE 416
denied-routes [network [network-mask] (OPTIONAL) Enter the keywords denied-routes then either the network address (in dotted decimal format) or the network mask (in slash prefix format) to view all information on routes denied via neighbor inbound filters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 417
The Lines Beginning with: Description BGP neighbor Displays the BGP neighbor address and its AS number. The last phrase in the line indicates whether the link between the BGP router and its neighbor is an external or internal one. If they are located in the same AS, the link is internal; otherwise the link is external. BGP version Displays the BGP version (always version 4) and the remote router ID.
PAGE 418
Example The Lines Beginning with: Description Prefix advertised Displays the number of network prefixes advertised, the number rejected, and the number withdrawn from the BGP routing table. Connections established Displays the number of TCP connections established and dropped between the two peers to exchange BGP information. Last reset Displays the amount of time since the peering session was last reset. Also states if the peer resets the peering session.
PAGE 419
Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last reset never Local host: 172.16.0.1, Local port: 58145 Foreign host: 172.16.0.2, Foreign port: 179 Dell# Related Commands show ip bgp — views the current BGP routing table. show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status.
PAGE 420
Example Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop. Cost Displays the cost associated with using this next hop. Flaps Displays the number of times the next hop has flapped. Time Elapsed Displays the time elapsed since the next hop was learned. If the route is down, this field displays time elapsed since the route went down.
PAGE 421
• { } = (braces) minimum and the maximum match count. • ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. $ = (dollar sign) the end of the output string. • Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 422
Dell#show ip bgp paths Total 2 Paths Refcount Metric Path 1 0 200 i 1 0 200 i show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. S6000 Syntax Parameters show ip bgp [vrf vrf-name] paths community vrf vrf-name (OPTIONAL) Enter the keyword vrf to view all unique COMMUNITY numbers in the BGP database corresponding to that VRF.
PAGE 423
Example Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these communities. Community Displays the community attributes in this BGP path. Dell#show ip bgp paths community Total 2 communities Refcount Community 1 NO-ADVERTISE 1 200:1 1000:1 3000:1 show ip bgp peer-group Allows you to view information on the BGP peers in a peer group.
PAGE 424
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.4. (0.0) Added support for VRF. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Added the add-path option to the S4810.
PAGE 425
Peer-group members (* - outbound optimized): 172.16.0.2 Dell# Related Commands neighbor peer-group (assigning peers) — assigns a peer to a peer-group. neighbor peer-group (creating group) — creates a peer group. show ip bgp regexp Display the subset of the BGP routing tables matching the regular expressions specified.
PAGE 426
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 427
*> 66.0.0.0/24 172.16.0.2 0 200 i show ip bgp summary Allows you to view the status of all BGP connections. S6000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] summary vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view the status of all BGP connections corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 428
If two peers send the same route that contains similar path attributes, then two entries are maintained in the back-end, as both these entries have different nexthops. If this same route is sent to a different peer, an entry for each peer is created, as the next-hop is different. As a result, the BGP attributes count in the summary output will differ accordingly. The following describes the show ip bgp summary command shown in the following example.
PAGE 429
Field Description represents the number of messages waiting to be sent to the peer group. Up/Down Displays the amount of time that the neighbor is in the Established stage. If the neighbor has never moved into the Established stage, the word never is displayed.
PAGE 430
show running-config bgp To display the current BGP configuration, use this feature. S6000 Syntax show running-config bgp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 431
holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 432
To disable debugging, use the no debug ip bgp ipv4 multicast dampening command. Parameters dampening Enter the keyword dampening to debug route flap dampening information. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.
PAGE 433
Usage Information Version 9.4(0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered.
PAGE 434
Content Addressable Memory (CAM) 10 Content addressable memory (CAM) commands are supported on the Dell Networking S6000 platform. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance. CAM Profile Commands The CAM profiling feature allows you to partition the CAM to best suit your application.
PAGE 435
validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR).
PAGE 436
Command Modes 436 ecfmacl number Enter the keyword ecfmacacl and then the number of FP blocks for ECFM ACL. The range is from 0 to 5. Vman-qos| vman-dual-qos number Enter the keyword evman-qos and then the number of FP blocks for VMAN QoS. The range is from 0 to 6. vman-dual-qos number Enter the keyword vman-dual-qos and then the number of FP blocks for VMAN dual QoS. The range is from 0 to 4. Ipv4pbr number Enter the keyword ipv4pbr and then the number of FP blocks for ipv4pbr ACL.
PAGE 437
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for PBR and VRF. Version 9.2(0.2) Added support for fcoe. Version 9.1. (0.0) Added support for OpenFlow. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 438
Parameters default Reset egress CAM ACL entries to default settings. l2acl number Allocate space to each CAM region. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.. Version 9.0.2.
PAGE 439
Version 7.8.1.0 Usage Information Introduced on the C-Series. When you enable this command, if a Policy Map containing classification rules (ACL and/or dscp/ ip-precedence rules) is applied to more than one physical interface on the same port pipe, only a single copy of the policy is written (only one FP entry is used). NOTE: An ACL itself may still require more that a single FP entry, regardless of the number of interfaces.
PAGE 440
FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : 0 0 0 0 0 0 -- Stack unit 0 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 -- Stack unit 7 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos :
PAGE 441
-- Line card 4 -Current Settings(in block sizes) L2Acl : 5 Ipv4Acl : 5 Ipv6Acl : 1 Ipv4Qos : 1 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos: 0 Ipv4pbr : 0 Dell# test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. S6000 Syntax Parameters test cam-usage service-policy input input policy name linecard {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters.
PAGE 442
QoS Optimization for IPv6 ACLs does not impact the CAM usage for applying a policy on a single (or the first of several) interfaces. It is most useful when a policy is applied across multiple interfaces; it can reduce the impact to CAM usage across subsequent interfaces. The following describes the test cam-usage command shown in the following example. Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks.
PAGE 443
Example (SSeries) Term Explanation Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for linecards and port-pipes in the chassis. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile. Estimated CAM per Port Estimates the amount of CAM space the listed policy will require. Status Indicates whether or not the policy will be allowed in the CAM.
PAGE 444
11 Control Plane Policing (CoPP) The CoPP commands are supported on the Dell Networking S6000 platform. control-plane-cpuqos To manage control-plane traffic, enter control-plane mode and configure the switch. S6000 Syntax control-plane-cpuqos Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 445
Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810.
PAGE 446
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. This command applies the service-policy based on the type of protocol defined in the ACL rules. Create ACL and QoS policies prior to enabling this command. For CoPP, use the keyword cpu-qos when creating qos-policy-input. Related Commands ip access-list extended — creates an extended IP ACL.
PAGE 447
Version 8.3.8.0 Usage Information Introduced on the S4810. This command applies the service-policy based on the type of protocol defined in the ACL rules. Create ACL and QoS policies prior to enabling this command. Example Dell#show cpu-queue rate cp for 8 queue platform Service-Queue Rate (PPS) -------------- ----------Q0 1300 Q1 300 Q2 300 Q3 300 Q4 2000 Q5 400 Q6 400 Q7 1100 Dell# show ip protocol-queue-mapping Display the queue mapping for each configured protocol.
PAGE 448
100 UDP (DHCP) UDP (DHCP-R) TCP (FTP) ICMP IGMP TCP (MSDP) UDP (NTP) OSPF PIM UDP (RIP) TCP (SSH) TCP (TELNET) VRRP Dell# 67/68 67 any any any any/639 any any any any any any any 68/67 67 21 any any 639/any 123 any any 520 22 23 any _ _ _ _ _ _ _ _ _ _ _ _ _ Q6/Q5 Q6 Q6 Q6 Q7 Q6 Q6 Q7 Q7 Q7 Q6 Q6 Q7 CP CP CP CP CP CP CP CP CP CP CP CP CP _ _ _ _ _ _ _ _ _ _ _ _ _ show ipv6 protocol-queue-mapping Display the queue mapping for each configured IPv6 protocol.
PAGE 449
show mac protocol-queue-mapping Display the queue mapping for the MAC protocols. S6000 Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 450
Data Center Bridging (DCB) 12 Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell Networking operating software commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 451
Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default, iSCSI is enabled on the unit and flow control is enabled on all of the interfaces or if link-level flow control is enabled on one or more interfaces.
PAGE 452
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. If you do not use the statistics parameter, both hardware and DCBx counters clear. dcb-input To apply pause or flow control for specified priorities using a configure delay time, create a DCB input policy.
PAGE 453
Usage Information NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future. As soon as you apply a DCB policy with PFC enabled on an interface, DCBx starts exchanging information with PFC-enabled peers. The IEEE802.1Qbb, CEE, and CIN versions of PFC TLV are supported.
PAGE 454
Version 8.3.16.0 Usage Information Introduced on the MXL 10/40GbE Switch IO Module. NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future. If you apply an input policy with PFC disabled (no pfc mode on): • You can enable link-level flow control on the interface.
PAGE 455
To remove only the DCB input policies applied to the specified switch, use the no dcb-policy input stack-unit command. Parameters stack-unit-id Enter the stack unit identification. dcb-inputpolicy-name Enter the policy name for the DCB input policy. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 456
pfc no-drop queues 1,3 or pfc no-drop queues 7 or pfc no-drop queues 0,7. The range is from 0 to 3. Defaults No lossless queues are configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 457
pfc priority Configure the CoS traffic to be stopped for the specified delay. S6000 Syntax pfc priority priority-range To delete the pfc priority configuration, use the no pfc priority command. Parameters priority-range Enter the 802.1p values of the frames to be paused. Separate the priority values with a comma; specify a priority range with a dash; for example, pfc priority 1,3,5-7. The range is from 0 to 7.
PAGE 458
Related Commands dcb-input — creates a DCB input policy. show dcb Displays the data center bridging status, the number of PFC-enabled ports, and the number of PFCenabled queues. S6000 Syntax Parameters show dcb [stack-unit unit-number] [port-set port-set port-set number] unit number Enter the DCB unit number. The range is from 0 to 5. port-set number Enter the port-set number. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 459
Parameters port-type slot/ port pfc Enter the port-type slot and port PFC information. {summary | detail} Enter the keyword summary for a summary list of results or enter the keyword detail for a full list of results. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 460
Field Description Operational status (local port) Port state for current operational PFC configuration: • Init: Local PFC configuration parameters were exchanged with the peer. • Recommend: Remote PFC configuration parameters were received from the peer. • Internally propagated: PFC configuration parameters were received from the configuration source. PFC DCBX Oper status Operational status for the exchange of the PFC configuration on the local port: match (up) or mismatch (down).
PAGE 461
Example (Summary) Field Description PFC TLV Statistics: Error pkts Number of PFC error packets received. PFC TLV Statistics: Pause Tx pkts Number of PFC pause frames transmitted. PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
PAGE 462
show interface pfc statistics Displays counters for the PFC frames received and transmitted (by dot1p priority class) on an interface. S6000 Syntax Parameters show interface port-type slot/port pfc statistics port-type Enter the port type. slot/port Enter the slot/port number. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 463
ETS Commands The following ETS commands are supported on the S6000 platform. dcb-enable Enable data center bridging. S6000 Syntax dcb enable[pfc-queues 1|4] To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 or 2. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 464
dcb-output To associate an ETS configuration with priority traffic, create a DCB output policy. S6000 Syntax dcb-output policy-name To remove the ETS output policy globally, use the no dcb output policy-name command. Parameters policy-name Enter the DCB output policy name. The maximum is 32 alphanumeric characters. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 465
dcb-policy output Apply the output policy with the ETS configuration to an egress interface. S6000 Syntax dcb-policy output policy-name To delete the output policy, use the no dcb-policy output command. Parameters policy-name Enter the output policy name. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 466
clear ets counters Clear all ETS TLV counters on an interface. S6000 Syntax Parameters clear ets counters port-type slot/port port-type Enter the keywords port-type then the slot/port information. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.
PAGE 467
The following is a list of the Dell Networking OS version history for this command. Example (Summary) Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.2) Down status messages added. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 468
0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Dell(conf-qos-policy-out-ets)#do sho int te 0/3 ets de Interface TenGigabitEthernet 0/3 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Remote Parameters
PAGE 469
Admin is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# Bandwidth TSA 0 13% ETS 1 13% ETS 2 13% ETS 3 13% ETS 4 12% ETS 5 12% ETS 6 12% ETS 7 12% ETS Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# Bandwidth TSA 0 13% ETS 1 13%
PAGE 470
1 2 3 4 5 6 7 0% 0% 0% 0% 0% 0% 0% ETS ETS ETS ETS ETS ETS ETS Priority# 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Bandwidth 13% 13% 13% 13% 12% 12% 12% 12% TSA ETS ETS ETS ETS ETS ETS ETS ETS Bandwidth 100% 0% 0% 0% 0% 0% 0% 0% TSA ETS ETS ETS ETS ETS ETS ETS ETS Local Parameters : -----------------Local is enabled TC-grp Priority# 0 0,1,2,3,4,5,6,7 1 2 3 4 5 6 7 Priority# Bandwidth TSA 0 13% ETS 1 13% ETS 2 13% ETS 3 13% ETS 4 12% ETS 5 12% ETS 6 12% ETS 7 12% ETS Op
PAGE 471
advertise dcbx-tlv On a DCBX port with a manual role, configure the PFC and ETS TLVs advertised to DCBX peers. S6000 Syntax advertise dcbx-tlv {ets-conf | ets-reco | pfc} [ets-conf | etsreco | pfc] [ets-conf | ets-reco | pfc] To remove the advertised ETS TLVs, use the no advertise dcbx-tlv command. Parameters {ets-conf | etsreco | pfc} Enter the PFC and ETS TLVs advertised, where: • ets-conf: enables the advertisement of ETS configuration TLVs.
PAGE 472
Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. dcbx port-role Configure the DCBX port role the interface uses to exchange DCB information. S6000 Syntax dcbx port-role {config-source | auto-downstream | auto-upstream | manual} To remove DCBX port role, use the no dcbx port-role {config-source | auto-downstream | auto-upstream | manual} command.
PAGE 473
Usage Information DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. dcbx version Configure the DCBX version used on the interface. S6000 Syntax dcbx version {auto | cee | cin | ieee-v2.5} To remove the DCBX version, use the dcbx version {auto | cee | cin | ieee-v2.5} command.
PAGE 474
Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. debug dcbx Enable DCBX debugging. S6000 Syntax debug dcbx {all | auto-detect-timer | config-exchng | fail | mgmt | resource | sem | tlv} To disable DCBX debugging, use the no debug dcbx command.
PAGE 475
fcoe priority-bits Configure the FCoE priority advertised for the FCoE protocol in application priority TLVs. S6000 Syntax fcoe priority-bits priority-bitmap To remove the configured FCoE priority, use the no fcoe priority-bits command. Parameters priority-bitmap Enter the priority-bitmap range. The range is from 1 to FF. Defaults 0x8 Command Modes PROTOCOL LLDP Command History This guide is platform-specific.
PAGE 476
Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 477
Version 8.3.16.0 Usage Information Introduced on the MXL 10/40GbE Switch IO Module. To clear DCBX frame counters, use the clear dcbx counters interface stack-unit/port command. The following describes the show interface dcbx detail command shown in the following example. Field Description Interface Interface type with chassis slot and port number. Port-Role Configured the DCBX port role: auto-upstream, autodownstream, config-source, or manual.
PAGE 478
Example Field Description Local DCBX Status: Protocol State Current operational state of the DCBX protocol: ACK or INSYNC. Peer DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs received from the peer device. Peer DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs received from the peer device. Peer DCBX Status: Sequence Number Sequence number transmitted in Control TLVs received from the peer device.
PAGE 479
Local DCBX TLVs Transmitted: ErPfi Local DCBX Status ----------------DCBX Operational Version is 0 DCBX Max Version Supported is 0 Sequence Number: 2 Acknowledgment Number: 2 Protocol State: In-Sync Peer DCBX Status: ---------------DCBX Operational Version is 0 DCBX Max Version Supported is 255 Sequence Number: 2 Acknowledgment Number: 2 Total DCBX Frames transmitted 27 Total DCBX Frames received 6 Total DCBX Frame errors 0 Total DCBX Frames unrecognized 0 dcb-map Create a DCB map to configure priority flo
PAGE 480
and ETS settings in the map are applied when the Ethernet port is enabled. DCBx is enabled on Ethernet ports by default. The dcb-map command is supported only on physical Ethernet interfaces. To remove a DCB map from an interface, enter the no dcb-map map-name command in Interface configuration mode. priority-pgid Assign 802.1p priority traffic to a priority group in a DCB map.
PAGE 481
Usage Information PFC and ETS settings are not pre-configured on Ethernet ports. You must use the dcb-map command to configure different groups of 802.1p priorities with PFC and ETS settings. Using the priority-pgid command, you assign each 802.1p priority to one priority group. A priority group consists of 802.1p priority values that are grouped together for similar bandwidth allocation and scheduling, and that share latency and loss requirements. All 802.
PAGE 482
Command Modes Command History Usage Information DCB MAP Version 9.3(0.0) Introduced on the S4810, S6000 platforms. Use the dcb-map command to configure priority groups with PFC and/or ETS settings and apply them to Ethernet interfaces. Use the priority-pgid command to map 802.1p priorities to a priority group. You can assign each 802.1p priority to only one priority group. A priority group consists of 802.
PAGE 483
Defaults None Command Modes CONFIGURATION Command History Usage Information Version 9.3(0.0) Introduced on the S4810 and S6000 platforms. The dcb-map stack-unit all stack-ports all command overwrites any previous DCB maps applied to stack ports. dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. This utility is supported on the S6000 platform. You must configure the shared buffer size to be less than the total PFC buffer size.
PAGE 484
Dell(conf)#dcb pfc-shared-buffer-size 2000 %ERROR: pfc shared buffer size configured cannot accommodate existing buffer requirement in the system. Example Dell(conf)#dcb pfc-shared-buffer-size 5000 dcb-buffer-threshold Configure the profile name for the DCB buffer threshold. This utility is supported on the S4810, S4820T, and S6000 platforms. S6000 Syntax Parameters dcb buffer—threshold profile-name profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
PAGE 485
buffer-size Ingress buffer size size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 45 KB. pausethreshold Buffer limit for pause frames to be sent thresholdvalue Buffer limit at which the port sends the pause to peer in KB. Enter a number in the range of 0 to 7787. The default is 10 KB. resume-offset Buffer offset limit for resuming in KB thresholdvalue Buffer offset limit at which the port resumes the peer in KB.
PAGE 486
qos-policy-buffer Create a QoS policy buffer and enter the configuration mode to configure the no-drop queues, ingress buffer size, buffer limit for pausing, and buffer offset limit for resuming.
PAGE 487
Default The default size of the ingress buffer is 45 KB. The default buffer limit at which the port sends the pause to peer and recommences the sending of packets to the peer is 10 KB. The default threshold weight of the shared buffer space is 10. Command Modes DCB-BUFFER-THRESHOLD mode Command History Usage Information Version 9.3(0.0) Introduced on the S4810, S4820T, S6000, and MXL platforms.
PAGE 488
profile-name Default None Command Modes INTERFACE mode Command History Version 9.3(0.0) Enter the name of the profile, which can be a string of up to 32 characters in length. Introduced on the S4810, S4820T, and S6000 platforms. Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process.
PAGE 489
Example Dell#show qos dcb buffer-threshold Name : test1 Buffer threshold parameters: pfc priority 0 buffer-size 40 pfc priority 3 buffer-size 50 show hardware stack-unit buffer-stats-snapshot (With Polling and History) View the buffer statistics tracking resource information with polling details and historical snapshots. This command is supported on the S6000 platform.
PAGE 490
• Command Modes Summary - Displays the consolidated information pertaining to the preceding three instances of the snapshot values collected in history. EXEC EXEC Privilege Command History Usage Information Version 9.3(0.0) Introduced on the S6000 platform. When you enter the “instance all” option, “show hardware stack-unit 0 buffer-statssnapshot unit 0 resource X” Output for all available instances on the history collection is displayed.
PAGE 491
Instance 3 Instance 4 Instance 5 10S 20S 30S 40S 50S -------------------------------------------------------------------------------------------------------------UCAST 2 5 4 6 0 1 UCAST 3 2 0 1 5 0 UCAST 11 0 3 2 0 3 MCAST 4 0 0 0 0 3 If only two instances are available at the time the above show command is issued, only two instances will be displayed in the summary output.
PAGE 492
for high-priority traffic that needs to be queued and preserved above the input queue limit, such as keepalives and hello messages. You can use the following sample command output to obtain a consolidated, whole-scale set of statistical counters of buffer resource utilization in the system and identify the ports that you want. All resources will be cleared after their values are displayed.
PAGE 493
--------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 UCAST 10 0 UCAST 11 0 MCAST 0 0 MCAST 1 0 MCAST 2 0 MCAST 3 0 MCAST 4 0 MCAST 5 0 MCAST 6 0 MCAST 7 0 MCAST 8 0 <… snip …> Stack-unit: 0 unit: 0 port: 104 (interface Te 0/124) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 1 0 0 2 0 0 3
PAGE 494
To determine the port that is congested and monitor all queues (including multicast and unicast queues] only on that port: Dell#$show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 queue all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 UCAST 10 0 UCAST 11 1 MCAST 0 0 MCAST 1 0 MC
PAGE 495
UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST Dell# 0 1 2 3 4 5 6 7 8 9 10 11 0 0 0 0 0 0 0 0 0 0 0 0 To identify the port that is congested and monitor all the priority groups on that particular port: Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 prio all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6
PAGE 496
Default The default is 1 KB for S6000 platforms. Command Modes CONFIGURATION mode Command History Usage Information Version 9.3(0.0) Introduced on the S6000 platform. Configure the maximum buffer available for PFC traffic. You can choose to increase or decrease the buffer size that is currently allocated in the system by default.
PAGE 497
Example Field Description Profile name Name of the DCB buffer threshold profile Priority The priority of the queue for which the buffer space settings apply buffer-size Ingress buffer size pause-threshold-value Buffer limit at which the port sends the pause to peer in KB. resume-threshold-value Buffer offset limit at which the port resumes the peer in KB.
PAGE 498
Dell#show interface tengigabitethernet 0/20 pfc bufferthreshold The following table describes the output fields displayed for the show interface pfc buffer-threshold command: Field Description queue Number of the queue lossless Whether the queue is a lossy or lossless queue for which buffer threshold is configured buffer-size Ingress buffer size pause-threshold-value Buffer limit at which the port sends the pause to peer in KB.
PAGE 499
Example Dell(conf)#dcb pfc-queues 4 dcb enable Enable priority flow control or enhanced transmission selection on interface. This feature is supported on S6000 platform. Syntax dcb enablepfc >enable • To disable ETS on interface, use “no dcb ets enable” command. • To disable PFC on interface, use “no dcb pfc enable” command. Defaults Enable Command Modes INTERFACE Command History Usage Information Limitations Related Commands Version 9.3 (0.
PAGE 500
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell Networking Operating System (OS) on the S6000 platform. This chapter contains the following sections: • • • Offline Diagnostic Commands Buffer Tuning Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter.
PAGE 501
password Enter a password to access the target server. ftp-password Enter the password of the target ftp server where the application core dump files will be uploaded. The password can be up to 15 alphanumeric characters; no special characters are allowed. Defaults Crash kernel files are uploaded to flash by default. Command Modes CONFIGURATION Command History Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 502
logging coredump stack-unit Enable coredump on a stack. S6000 Syntax Parameters logging coredump stack-unit {0–5 | all} stack-unit 0–5 Enter the stack-unit id. For S6000 the range is from 0 to 5. all Enable coredump on all stack-unit. Defaults Enabled by default on customer builds. Command Modes CONFIGURATION Command History Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 503
filter Specify the packet that will be dumped. If no filter is entered, all packets are dumped. Filter expressions usually consist of an id (name or number) preceded by one or more qualifiers. There are three different kinds of qualifier: type, direction, or protocol. Enclose the filter option with double quotes: “port 20.” The range is 1 to 100 characters. packet-count Enter the number of packets to capture. The counter begins as soon as the command is enabled. The range is 10 to 150000.
PAGE 504
Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby. Important Points to Remember • • • • Offline diagnostics can only be run when the unit is offline. You can only run offline diagnostics on a unit to which you are connected via the console.
PAGE 505
snake tests using VLAN configurations. To test 10G links, physically remove the unit from the stack. verbose Enter the keyword verbose to run the diagnostic in Verbose mode. Verbose mode gives more information in the output than Standard mode. testname Enter the keyword level2 to run a specific test case. Enclose the test case name in double quotes (“ “). For example: diag stack-unit 1 level1 testname “first”.
PAGE 506
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added a warning message to the off-line diagnostic. Version 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete.
PAGE 507
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented. Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags.
PAGE 508
cpu party-bus statistics Enter the keywords cpu party-bus statistics to clear the management statistics. stack-port Enter the keywords stack-port then the port number of the stacking port to clear the statistics of the particular stacking port. The range is 0 to 127 for the S6000. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 509
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 510
show hardware layer2 Display Layer 2 ACL or eg data for the selected stack member and stack member port-pipe. S6000 Syntax Parameters show hardware layer2 {eg-acl | in-acl} stack-unit id port-set 0–0 eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack-unit id Enter the keyword stack-unit to select a stack ID. The range is 0 for the S6000. port-set 0–0 Enter the keywords port-set with a port-pipe number. .
PAGE 511
stack-unit number Enter the keywords stack-unit then a number to select a stack ID. The range is 0 to 5 for the S6000. port-set 0–0 Enter the keyword port-set with a port-pipe number. The range is 0 to 0 for the S6000. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 512
To display total buffer information for the port, enter the keywords buffer-info. To display a queue range, enter 0 to 14 for a specfic queue or all. cpu data-plane statistics (Optional) Enter the keywords cpu data-plane statistics then the keywords stack port and its number, from 0 to 63 to display the data plane statistics, which shows the High Gig (Higig) port raw input/output counter statistics to which the stacking module is connected.
PAGE 513
Version 9.2(0.2) Modified the drops keyword range, unit keyword range and added the buffer and cpu management statistics options. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.5 Added i2c statistics and sata-interfaces statistics. Version 8.3.11.4 Added user port information. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series.
PAGE 514
Example (Drops Unit) Dell#sh hard stack-unit 0 drops unit 0 PortNumberIngress Drops IngMac Drops Total Mmu Drops 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 EgMac Drops Egress Drops 0 0 0 0 0 0 0 0 Dell# Example (Drops Unit, Port) Dell#show hardware stack-unit 0 drops unit 1 port 27 --- Ingress Drops --Ingress Drops : 0 IBP CBP Full Drops : 0 PortSTPnotFwd Drops : 0 IPv4 L3 Discards : 0 Policy Discards : 0 Packets dropped by FP : 0 (L2+L3) Drops : 0 Port bitmap zero Drops : 0 Rx VLAN Drops : 0 --- Ingress MAC counte
PAGE 515
ge13 !ena ge14 !ena ge15 !ena ge16 !ena ge17 !ena ge18 !ena ge19 !ena ge20 !ena ge21 !ena ge22 !ena ge23 !ena hg0 up 12G FD hg1 up 12G FD hg2 down 10G FD hg3 down 10G FD 0 Dell# Example (Register) SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Forward Tag Tag Tag Tag Tag Tag Tag Tag Tag Tag Tag None None None None F F F F F F F F F F F F F
PAGE 516
0x0e70b102 BCAST_BLOCK_MASK.ge11 = 0x00000000 0x0e70c102 BCAST_BLOCK_MASK.ge12 = 0x00000000 0x0e70d102 BCAST_BLOCK_MASK.ge13 = 0x00000000 0x0e70e102 BCAST_BLOCK_MASK.ge14 = 0x00000000 0x0e70f102 BCAST_BLOCK_MASK.ge15 = 0x00000000 0x0e710102 BCAST_BLOCK_MASK.ge16 = 0x00000000 0x0e711102 BCAST_BLOCK_MASK.ge17 = 0x00000000 0x0e712102 BCAST_BLOCK_MASK.ge18 = 0x00000000 0x0e713102 BCAST_BLOCK_MASK.ge19 = 0x00000000 0x0e714102 BCAST_BLOCK_MASK.ge20 = 0x00000000 0x0e715102 BCAST_BLOCK_MASK.
PAGE 517
The linkStatus of Front End Port 6 is FALSE The linkStatus of Front End Port 7 is FALSE The linkStatus of Front End Port 8 is FALSE The linkStatus of Front End Port 9 is FALSE The linkStatus of Front End Port 10 is FALSE The linkStatus of Front End Port 11 is FALSE The linkStatus of Front End Port 12 is FALSE The linkStatus of Front End Port 13 is FALSE The linkStatus of Front End Port 14 is FALSE The linkStatus of Front End Port 15 is FALSE The linkStatus of Front End Port 16 is FALSE The linkStatus of Fro
PAGE 518
show hardware stack-unit buffer Display the counters for the specified port, minimum guaranteed buffer of a priority-group, and the shared buffer. This command is supported on the S6000 platform.
PAGE 519
Example Field Description Accounted Packet Buffer Shared buffer space that is in use by the packets FTOS# show hardware stack-unit 0 buffer unit 0 port 1 prioritygroup 0 buffer-info ----- Buffer Accounting Stats for Unit 0 Port 1 prioritygroup 0 ----Maximum Shared Limit: 0 Default Packet Buffer allocate for the priority-group: 61440 Accounted Packet Buffer: 0 show hardware system-flow Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe.
PAGE 520
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Example Dell#show hardware system-flow layer2 stack-unit 0 port-set 0 counters ----------------------------------------------------------EntryId Description #HITS ----------------------------------------------------------2048 STP BPDU Redirects 0 2047 LLDP BPDU Redirects 0 2045 LACP traffic Redirects 0 2044 GVRP traffic Redirects 0 2043 ARP Reply Redirects 0 2042 802.
PAGE 521
################# FP Entry for redirecting GVRP traffic to RSM ########### EID 2044: gid=1, slice=15, slice_idx=0x03, prio=0x7fc, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 0180c200 00210000 00000000 00000000 , FPF4=0x00 MASK=0x00000000 00000000 00000000 ffffffff ffff0000 00000000 00000000 , 0x00 action={act=Drop, param0=0(0x00), param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x
PAGE 522
Command Modes • Port {id |all} queue {all} - egress queue-level snapshot for both unicast and multicast packets • Port {id |all} queue ucast {id | all} - egress queue-level snapshot for unicast packets only • Port {id |all} queue mcast {id | all} - egress queue-level snapshot for multicast packets only • Port {id |all} prio-group {id | all} - ingress priority-group level snapshot EXEC EXEC Privilege Command History Usage Information Version 9.3.0.0 Introduced on the S6000 platform.
PAGE 523
resource port 5 queue all Stack-unit 0 unit 0 port 5 (interface te 0/4) -------------------------------------------------------------------------------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS -------------------------------------------------------------------------------------------------------------UCAST 5 4 UCAST 6 8 UCAST 11 1 MCAST 4 11 Only the queues for which the buffer cell consumption is not zero are displayed.
PAGE 524
Command Modes buffer-statssnapshot unit number Display the historical snapshot of buffer statistical values unit Enter the keyword unit along with a port-pipe number, then the keyword counters to display the counters on the selected port-pipe. The range is 0 to 0.
PAGE 525
• Port- Priority-Group – Displays the shared space usage counters usage, headroom space counters per ingress port on per-priority-group granularity. When the buffer-stats-snapshot is disabled, the folloing informational message is displayed when you run the show command: %Info: Buffer-stats-snapshot feature is disabled.
PAGE 526
Dynamic Host Configuration Protocol (DHCP) 14 Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. The Dell Networking operating system supports the basic DHCP commands on the S6000 platform.
PAGE 527
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 528
default-router Assign a default gateway to clients based on the address pool. S6000 Syntax Parameters default-router address [address2...address8] address Enter a list of routers that may be the default gateway for clients on the subnet. You may specify up to eight routers. List them in order of preference. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 529
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. dns-server Assign a DNS server to clients based on address pool. S6000 Syntax Parameters dns-server address [address2...address8] address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference.
PAGE 530
Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 531
Version 8.2.1.0 Introduced on the C-Series and S-Series. hardware-address For manual configurations, specify the client hardware address. S6000 Syntax Parameters hardware-address address address Enter the hardware address of the client. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 532
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. lease Specify a lease time for the addresses in a pool. S6000 Syntax Parameters lease {days [hours] [minutes] | infinite} days Enter the number of days of the lease. The range is from 0 to 31. hours Enter the number of hours of the lease. The range is from 0 to 23.
PAGE 533
netbios-name-server Specify the NetBIOS Windows Internet Naming Service (WINS) name servers, in order of preference, that are available to Microsoft Dynamic Host Configuration Protocol (DHCP) clients. S6000 Syntax Parameters netbios-name-server address [address2...address8] address Enter the address of the NETBIOS name server. You may enter up to eight, in order of preference. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 534
Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 535
pool Create an address pool. S6000 Syntax Parameters pool name name Enter the address pool’s identifying name. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 536
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp configuration Display the DHCP configuration. S6000 Syntax Parameters show ip dhcp configuration [global | pool name] pool name Display the configuration for a DHCP pool. global Display the DHCP configuration for the entire system. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 537
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 538
Defaults Disabled Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 539
Related Commands arp inspection — enables dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. S6000 Syntax clear ip dhcp snooping binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 540
Usage Information Version 9.2. (0.0) Introduced on the S4810 and S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. Version 8.2.1.0 Introduced on the C-Series and S-Series on Layer 2 interfaces. Version 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces. When enabled, no learning takes place until you enable snooping on a VLAN.
PAGE 541
lease time Enter the keyword lease then the amount of time the IP address are leased. The range is from 1 to 4294967295. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 542
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping trust Configure an interface as trusted. S6000 Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 543
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 8.2.1.
PAGE 544
The following is a list of the Dell Networking OS version history for this command. Example Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on C-Series and S-Series.
PAGE 545
ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name] ip-address command. Parameters vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF through which the host address can be reached.
PAGE 546
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 547
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Usage Information Use this command to associate name server IP addresses to a specific VRF. Example • Dell(conf)#ip name-server vrf jay 2.2.2.
PAGE 548
Usage Information Use this command to configure a domain name corresponding to a VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. Example Dell(conf)#ip domain-name vrf jay dell.com ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 549
ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrf-name] name ip-address command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the name server to IP address mapping for that VRF.
PAGE 550
host-name Enter the name of the host corresponding to which you want to delete the dynamically learnt host table entries. * Enter * to delete all host table entries. Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.
PAGE 551
Equal Cost Multi-Path (ECMP) 15 Equal cost multi-path (ECMP) is supported on the Dell Networking S6000 platform. ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold. S6000 Syntax ecmp-group {ecmp-group-id interface interface | link-bundlemonitor} To remove the selected interface, use the ecmp-group no interface command.
PAGE 552
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID. You can then assign interfaces to the ECMP group using CONFIGURATION ECMP-GROUP mode. You can also enable on the port-channel configuration using the CONFIGURATION ECMP-GROUP command mode.
PAGE 553
ecmp crc16 | crc16cc | crc32MSB | crc32LSB | crcupper | dest-ip | lsb | xor1 | xor2 | xor4 | xor8 | xor16 hg {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} stack-unit stack-unitnumber | portset port-pipe TeraScale and ExaScale Only: Enter the keyword ecmp then one of the following options: • crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial • crc32MSB: Use CRC32_UPPER — MSB 16 bits of
PAGE 554
Enter the keywords port-set port-pipe then the port pipe number. The range is from 0 to 5. hg-seed seedvalue stackunit Z-Series only: Enter the keywords hg-seed then the hash algorithm seed value. The range is from 0 to 2147483646. Enter the keywords stack-unit then the stack unit number. The range is from 0 to 7. Enter the keywords port-set then the stack-unit port-pipe number. The range is from 0 to 5. lag hash algorithm Z-Series only: Enter the keywords hg-seed . The range is from 0 to 47.
PAGE 555
Version 7.7.1.1 Usage Information Added the nh-ecmp option. To ensure that CRC is not used for LAG, set the default hash-algorithm method on ExaScale systems. For example,hash-algorithm ecmp xor lag checksum nh-ecmp checksum. The hash value calculated with the hash-algorithm command is unique to the entire chassis. The hash algorithm command with the stack—unit option changes the hash for a particular stack—unit by applying the mask specified in the IPSA and IPDA fields.
PAGE 556
ip ecmp-group Enable and specify the maximum number of ecmp that the L3 CAM hold for a route, By default, when maximum paths are not configured, the CAM can hold a maximum of 16 ecmp per route. S6000 Syntax ip ecmp-group {maximum-paths | {number} {path-fallback} To negate a command, use the no ip ecmp-group maximum-paths {number} command. Parameters maximumpaths Specify the maximum number of ECMP for a route. The range is 2 to 64. path-fallback Use the keywords path-fallback to enable this feature.
PAGE 557
Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 558
Version 8.3.10.0 558 Introduced on the S4810.
PAGE 559
Flex Hash and Optimized Boot-Up 16 This chapter describes the Flex Hash and fast-boot enhancements. load-balance ingress-port enable Enable the Flex hash functionality. This utility is supported on the S6000 platform. Syntax load-balance ingress-port enable To disable the Flex hash capability, use the no version of this command. Default None Command Modes CONFIGURATION mode Command History Usage Information Version 9.3(0.0) Introduced on the S6000 platform.
PAGE 560
the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name. This utility is supported on the S6000 platform. Syntax load-balance flexhash ipv4/ipv6 ip-proto offset1 [offset2 ] To disable the Flex hash settings, use the no load-balance flexhash ipv4/ ipv6 ip-proto protocol number command. Parameters ipv4 Denotes whether Flex Hash needs to be enabled for IPv4 packets.
PAGE 561
headers are not sufficient to distinguish the flows. Therefore, the fields in the L4 header are processed when hashing is performed for packets over LAG and ECMP links. The Flex Hash functionality enables you to configure a packet search key and matches packets based on the search key. When a packet matches the search key, two 16-bit hash fields are extracted from the start of the L4 header and provided as inputs (bins 2 and 3) for RTAG7 hash computation.
PAGE 562
lacp fast-switchover Cause the physical ports to be aggregated faster by configuring this capability in a port-channel on both the nodes that are members of a port-channel. S6000 Syntax lacp fast-switchover To disable the capability of faster aggregation of the member ports of a LAG or a port-channel bundle, use the no version of this command. Defaults Not configured Command Modes INTERFACE (conf-if-po-number) Command History Usage Information Version 9.3(0.0) Introduced on the S6000.
PAGE 563
Command History Usage Information Version 9.3.0.0 Introduced on the S6000 platform. To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction.
PAGE 564
17 FCoE Transit To enable the FCoE Transit feature and configure FIP snooping, use the following Dell Networking Operating System commands on the platform. In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs).
PAGE 565
clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface. Syntax Parameters clear fip-snooping statistics [interface vlan vlan-id | interface port-type port/slot | interface port-channel portchannel-number] vlan-id Enter the VLAN ID of the FIP packet statistics to be cleared. port-type port/ slot Enter the port-type and slot number of the FIP packet statistics to be cleared.
PAGE 566
ifm Enter the keyword ifm for IFM-specific debugging. info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 567
• interface vlan-discovery — Enter the keywords vlandiscovery to enable debugging on VLAN requests and notifications. Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 568
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. fip-snooping enable Enable FIP snooping on all VLANs or on a specified VLAN. Syntax fip-snooping enable To disable the FIP snooping feature on all or a specified VLAN, use the no fipsnooping enable command. Defaults Command Modes Command History FIP snooping is disabled on all VLANs. • • CONFIGURATION VLAN INTERFACE This guide is platform-specific.
PAGE 569
Parameters fc-map-value Enter the FC-MAP value FIP snooping uses. The range is from 0EFC00 to 0EFCFF. Defaults 0x0EFC00 Command Modes • CONFIGURATION • VLAN INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 570
fip-snooping port-mode fcf Configure the port for bridge-to-FCF links. Syntax fip-snooping port-mode fcf To disable the bridge-to-FCF link on a port, use the no fip-snooping portmode fcf command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.
PAGE 571
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. The maximum number of FCoE VLANs supported on the switch is eight. show fip-snooping config Display the FIP snooping status and configured FC-MAP values. Syntax show fip-snooping config Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 572
show fip-snooping enode Display information on the ENodes in FIP-snooped sessions, including the ENode interface and MAC address, FCF MAC address, VLAN ID and FC-ID. Syntax Parameters show fip-snooping enode [enode-mac-address] enode-macaddress Enter the MAC address of the ENodes to display. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 573
show fip-snooping fcf Display information on the FCFs in FIP-snooped sessions, including the FCF interface and MAC address, FCF interface, VLAN ID, FC-MAP value, FKA advertisement period, and number of ENodes connected. Syntax Parameters show fip-snooping fcf [fcf-mac-address] fcf-macaddress Enter the MAC address of the FCF to display. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 574
54:7f:ee:37:34:40 Po 22 2 100 0e:fc:00 4000 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax Parameters show fip-snooping statistics [interface vlan vlan-id | interface port-type port/slot | interface port-channel portchannel-number] vlan-id Enter the VLAN ID of the FIP packet statistics displays. port-type port/ slot Enter the port-type and slot number of the FIP packet statistics displays.
PAGE 575
FCoE Transit Field Description Number of Multicast Discovery Solicits Number of FIP-snoop multicast discovery solicit frames received on the interface. Number of Unicast Discovery Solicits Number of FIP-snoop unicast discovery solicit frames received on the interface. Number of FLOGI Number of FIP-snoop FLOGI request frames received on the interface. Number of FDISC Number of FIP-snoop FDISC request frames received on the interface.
PAGE 576
Example Field Description Number of VN Port Session Timeouts Number of VN port session timeouts that occurred on the interface. Number of Session failures due to Hardware Config Number of session failures due to hardware configuration that occurred on the interface.
PAGE 577
Number Number Number Number Number Number Number Number Number Number Number Number Number Number Number Number Number Number Number of of of of of of of of of of of of of of of of of of of Multicast Discovery Solicits :0 Unicast Discovery Solicits :0 FLOGI :0 FDISC :0 FLOGO :0 Enode Keep Alive :0 VN Port Keep Alive :0 Multicast Discovery Advertisement :4451 Unicast Discovery Advertisement :2 FLOGI Accepts :2 FLOGI Rejects :0 FDISC Accepts :16 FDISC Rejects :0 FLOGO Accepts :0 FLOGO Rejects :0 CVL :0 FCF
PAGE 578
show fip-snooping vlan Display information on the FCoE VLANs on which FIP snooping is enabled. Syntax show fip-snooping vlan Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 579
Version 8.3.12.0 FCoE Transit Introduced on the S4810.
PAGE 580
18 Force10 Resilient Ring Protocol (FRRP) Force10 resilient ring protocol (FRRP) is supported on Dell Networking S6000 platform. FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a highspeed token across a ring to verify the link status.
PAGE 581
Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.5.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell Networking OS requires a command line confirmation before the command executes.
PAGE 582
detail Enter the keyword detail to display detailed debug information related to the entire ring protocol packets. ring-id (Optional) Enter the ring identification number. The range is from 1 to 255. count number Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Defaults Disabled. Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific.
PAGE 583
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced.
PAGE 584
interface Configure the primary, secondary, and control-vlan interfaces. S6000 Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 585
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration.
PAGE 586
Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. mode Set the Master or Transit mode of the ring. S6000 Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode.
PAGE 587
protocol frrp Enter the Resilient Ring Protocol and designate a ring identification. S6000 Syntax protocol frrp {ring-id} To exit the ring protocol, use the no protocol frrp {ring-id} command. Parameters ring-id Enter the ring identification number. The range is from 1 to 255. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 588
summary (OPTIONAL) Enter the keyword summary to view just a summarized version of the Ring configuration. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 589
Primary : GigabitEthernet 0/16 State: Forwarding Secondary: Port-channel 100 State: Blocking Control Vlan: 1 Ring protocol Timers: Hello-Interval 50 msec Dead-Interval 150 msec Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348 Number of state Changes: 34 Member Vlans: 1000-1009 Dell# Example (2 Summary) Dell#show frrp 2 summary Related Commands protocol frrp — enters the resilient ring protocol and designate a ring identification.
PAGE 590
Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 590 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 591
GARP VLAN Registration (GVRP) 19 The Dell Networking operating system supports the basic GVRP commands on the S6000platform. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 592
• VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all dynamic VLANs are removed. • GVRP manages the active topology, not non-topological data such as VLAN protocols. If a local bridge must classify and analyze packets by VLAN protocols, manually configure protocol-based VLANs, and simply rely on GVRP for VLAN updates.
PAGE 593
Related Commands show gvrp statistics — displays the GVRP statistics. debug gvrp Enable debugging on GVRP. S6000 Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/ LEAVE events.
PAGE 594
disable Globally disable GVRP. S6000 Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 595
NOTE: Designate the milliseconds in multiples of 100. leave Enter the keyword leave then the number of milliseconds to configure the leave time. The range is from 100 to 2147483647 milliseconds. The default is 600 milliseconds. NOTE: Designate the milliseconds in multiples of 100. leave-all Enter the keywords leave-all then the number of milliseconds to configure the leave-all time. The range is from 100 to 2147483647 milliseconds. The default is 1000 milliseconds.
PAGE 596
gvrp enable Enable GVRP on physical interfaces and LAGs. S6000 Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 597
Defaults normal Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 598
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on C-Series, E-Series, and S-Series disable — globally disables GVRP. show config Display the global GVRP configuration.
PAGE 599
show garp timers Display the GARP timer settings for sending GARP messages. S6000 Syntax show garp timers Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 600
interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 601
show gvrp statistics Display the GVRP configuration statistics. S6000 Syntax Parameters show gvrp statistics {interface interface | summary} interface interface summary (OPTIONAL) Enter the keyword interface then one of the interface keywords and slot/ port or number information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 602
• Example An entry for a new GVRP VLAN could not be created in the GVRP database.
PAGE 603
20 ICMP Message Types This chapter lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. ICMP Messages and Their Definitions.\ Symbol Type Code . Query Error Timeout (no reply) ! 0 U 3 C Description 4 5 ICMP Message Types 3 echo reply . destination unreachable: 0 network unreachable . 1 host unreachable .
PAGE 604
Symbol & Type Code Description 0 redirect for network . 1 redirect for host . 2 redirect for type-of-service and network . 3 redirect for type-of-service and host . 8 0 echo request . 9 0 router advertisement . 10 0 router solicitation . 11 Error time exceeded: 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 604 Query parameter problem: 1 IP header bad (catchall error) . 2 required option missing .
PAGE 605
Internet Group Management Protocol (IGMP) 21 The IGMP commands are supported by the Dell Networking operating software on the S6000 platform. This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376.
PAGE 606
• For a VLAN interface, enter the keyword vlan then the slot/port information. The range is from 1 to 4094. • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword tengigabitethernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Command Modes EXEC Command History This guide is platform-specific.
PAGE 607
interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information. • For a Port Channel interface, enter the keyword portchannel then a number. The range is from 1 to 128. • For a 10–Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 608
Parameters access-list Enter the name of the extended ACL (16 characters maximum). Enter the name of the extended ACL (139 characters maximum). Defaults Not configured Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.
PAGE 609
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.6.1.0 Introduced on the E-Series. ip igmp immediate-leave Enable IGMP immediate leave.
PAGE 610
Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion. In addition, this command provides a way to enable immediate-leave processing for specified groups.
PAGE 611
ip igmp querier-timeout Change the interval that must pass before a multicast router decides that there is no longer another multicast router that should be the querier. Syntax ip igmp querier-timeout seconds To return to the default value, use the no ip igmp querier-timeout command. Parameters seconds Enter the number of seconds the router must wait to become the new querier. The range is from 60 to 300. The default is 125 seconds.
PAGE 612
ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. S6000 Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 613
ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. S6000 Syntax ip igmp query-max-resp-time seconds To return to the default values, use the no ip igmp query-max-resp-time command. Parameters seconds Enter the number of seconds for the maximum response time. The range is from 1 to 25. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 614
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. S6000 Syntax ip igmp ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp ssm-map std-access-list sourceaddress command. Parameters std-access-list Specify the standard IP access list that contains the mapping rules for multicast groups.
PAGE 615
ip igmp static-group Configure an IGMP static group. S6000 Syntax ip igmp static-group {group address [exclude [source address]] | [include {source address}]} To delete a static address, use the no ip igmp static-group {group address [exclude [source address]] | [include {source address}]} command. Parameters group address Enter the group address in dotted decimal format (A.B.C.D). exclude source address (OPTIONAL) Enter the keyword exclude then the source address, in dotted decimal format (A.B.C.
PAGE 616
implicitly assumes all sources are included. If you do not specify either include or exclude, Dell Networking OS implicitly assumes a IGMPv2 static join. Command Limitations Related Commands • Only one mode (include or exclude) is permitted per multicast group per interface. To configure another mode, all sources belonging to the original mode must be unconfigured.
PAGE 617
Version 7.5.1.0 Introduced on the E-Series. show ip igmp groups View the IGMP groups. S6000 Syntax Parameters show ip igmp groups [group-address [detail] | detail | interface [group-address [detail]]] group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and slot/port information: detail • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 618
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series and C-Series. Version 7.5.1.0 Expanded to support the detail option. E-Series legacy command. Usage Information This command displays the IGMP database, including configured entries for either all groups on all interfaces, all groups on specific interfaces, or specific groups on specific interfaces.
PAGE 619
Group Address Interface Mode 225.0.0.0 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.1 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.2 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.3 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.4 Vlan 100 IGMPv2 Member Ports: Po 2* Uptime Expires Last Reporter 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 show ip igmp interface View information on the interfaces participating in IGMP.
PAGE 620
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results.
PAGE 621
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.7.1.0 Introduced on the E-Series. ip igmp ssm-map — uses a statically configured list to translate (*,G) memberships to (S,G) memberships.
PAGE 622
If the IP SA in the incoming IGMP general query frame is lower than the IP address of the VLAN interface, the switch disables its IGMP snooping Querier functionality. If the IP SA of the incoming IGMP general query is higher than the VLAN IP address, the switch continues to work as an IGMP snooping Querier. ip igmp snooping enable Enable IGMP snooping on all or a single VLAN. This command is the master on/off switch to enable IGMP snooping.
PAGE 623
ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. S6000 Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 624
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 625
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 626
Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 627
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This command enables the IGMP switch to send General Queries periodically. This behavior is useful when there is no multicast router present in the VLAN because the multicast traffic is not routed.
PAGE 628
Usage Information If the port channel is a VLT port channel, an asterisk (*) after the port channel number (Po 100*) indicates the port channel is locally down and that a remote VLT port is up. Example Dell#show ip igmp snooping mrouter Interface Router Ports Vlan 2 Gi 13/3, Po 1 Dell# Related Commands 628 • ip igmp snooping mrouter — configures a static connection to the multicast router. • show ip igmp groups — view groups.
PAGE 629
22 Interfaces The commands in this chapter are supported by Dell Networking operating software on the S6000 platform. This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands • Time Domain Reflectometer (TDR) • UDP Broadcast Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 630
• For a 10-Gigabit Ethernet interface, enter the keyword tenGigE then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a tunnel interface, enter the keyword tunnel. The range is from 1 to 16383. vrrp [[ipv6] vrid] (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
PAGE 631
Related Commands mac learning-limit — allows aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. show interfaces — displays information on the interfaces. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 632
Example Dell#clear dampening tegigabitethernet 1/2 Clear dampening counters on TeGi 1/2 [confirm] y Dell# Related Commands show interfaces dampening — displays interface dampening information. dampening — configures dampening on an interface. dampening Configure dampening on an interface. S6000 Syntax Parameters dampening [[[[half-life] [reuse-threshold]] [suppressthreshold]] [max-suppress-time]] half-life Enter the number of seconds after which the penalty is decreased.
PAGE 633
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. With each flap, Dell Networking OS penalizes the interface by assigning a penalty (1024) that decays exponentially depending on the configured half-life. After the accumulated penalty exceeds the suppress threshold value, the interface moves to the Error-Disabled state.
PAGE 634
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Modified for E-Series: Revised from 78 to 240 characters.
PAGE 635
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Introduced Usage Information This command applies to any physical interface with speed set to 10/100.
PAGE 636
Parameters tx off Enter the keywords tx off so that flow control frames are not sent from this port to the connected device when a higher rate of traffic is received. rx on Enter the keywords rx on to process the received flow control frames on this port. rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received.
PAGE 637
When a port receives traffic at a higher rate than it can process, the frames are stored in the port buffer. As a result, buffer usage increases. When the buffer usage reaches the value specified in the “pause-threshold” argument, the port sends PAUSE frame to the connected link partner to stop sending the traffic. Eventually this reduces the buffer usage. When the buffer usage drops by the value specified in the “resume-threshold”, the port again sends a PAUSE frame with 0 as wait-time.
PAGE 638
Related Commands on on off on off off on on off on off on on off off off on on off on off on on on off off on on off on off on LocNegRx off off off off LocNegTx RemNegRx RemNegTx off off off off off off off off off off off off off off off off off off on off off off on off off off off off off on on on off off on on off off on on off on on on off off on on off off on on off off on on off off on on show running-config — displays the flow configuration parameters (non-default values
PAGE 639
range • For a Loopback interface, enter the keyword loopback then the slot/port information. The range is from 0 to 16383. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Tunnel interface, enter the keyword tunnel then the tunnel ID. The range is from 1 to 16383.
PAGE 640
The tunnel interface operates as an ECMP (equal cost multi path) only when the next hop to the tunnel destination is over a physical interface. If you select any other interface as the next hop to the tunnel destination, the tunnel interface does not operate as an ECMP. Example Dell(conf)#int tengigabitethernet 0/0 Dell(conf-if-te-0/0)#exit Dell(conf)# Related Commands interface loopback — configures a Loopback interface. interface null — configures a Null interface.
PAGE 641
gigabitethernet 0/1 - 5 ; interface group gigabitethernet 0/1-5. Command Modes Command History Usage Information • For a Gigabit Ethernet interface, enter the keyword gigabitethernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 642
Parameters number Enter a number as the interface number. The range is from 0 to 16383. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 643
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.11.1 Introduced on the S55, S60, and S4810. Version 8.1.1.
PAGE 644
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 645
the range of interfaces for bulk configuration. You can enter up to six comma-separated ranges. Spaces are not required between the commas. Comma-separated ranges can include VLANs, port-channels, and physical interfaces. Slot/Port information must contain a space before and after the dash. For example, interface range gigabitethernet 0/1 - 5 is valid; interface range gigabitethernet 0/1-5 is NOT valid. • For a Port Channel interface, enter the keywords portchannel then a number.
PAGE 646
Usage Information When creating an interface range, interfaces appear in the order they are entered; they are not sorted. The command verifies that interfaces are present (physical) or configured (logical). Important Points to Remember: • Bulk configuration is created if at least one interface is valid. • Non-existing interfaces are excluded from the bulk configuration with a warning message. • The interface range prompt includes interface types with slot/port information for valid interfaces.
PAGE 647
Example (Multiple Range) This example shows how to use commas to add different interface types to the range enabling all Gigabit Ethernet interfaces in the range 5/1 to 5/23 and both Ten-Gigabit Ethernet interfaces 1/1 and 1/2. Dell(config-if)# interface range gigabitethernet5/1-23, tengigabitethernet1/1-2 Dell(config-if-range)# no shutdown Dell(config-if-range)# Example (Multiple Range) This example shows how to use commas to add SONET, VLAN, and port-channel interfaces to the range.
PAGE 648
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Tunnel interface, enter the keyword tunnel then the tunnel ID. The range is from 1 to 16383. For a VLAN, enter the keyword vlan followed by a number from 1 to 4094.
PAGE 649
Related Commands interface range – configures a range of command (bulk configuration) interface range macro name – runs an interface range macro. interface range macro name Run the interface-range macro to automatically configure the pre-defined range of interfaces. S6000 Syntax Parameters interface range macro name name Enter the name of an existing macro. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 650
interface vlan Configure a VLAN. You can configure up to 4094 VLANs. S6000 Syntax interface vlan vlan-id [of-instance{of-id}] Syntax interface vlan vlan-id Parameters vlan-id Enter a number as the VLAN Identifier. The range is from 1 to 4094. of-instance{ofid} Enter the keyword of-instance then the OpenFlow instance ID to add the VLAN to the specified OpenFlow instance. The range is from 1 to 8. NOTE: Associate the OpenFlow instance with the VLAN when the VLAN is created.
PAGE 651
• MTU If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously. Example (Single Range) Dell(conf)#int vlan 3 Dell(conf-if-vl-3)# Related Commands interface — configures a physical interface. interface loopback — configures a loopback interface. interface null — configures a null interface. interface port-channel — configures a port channel group. show vlan — displays the current VLAN configuration on the switch. shutdown — disables/enables the VLAN.
PAGE 652
Usage Information Related Commands If you configure interface type as CR4 with auto-negotiation enabled, also configure CR4 with auto-negotiation. Many DAC cable link issues are resolved by setting the interface type as CR4. • Interfaces — configures a physical interface. • interface loopback — configures a loopback interface. • interface null — configures a null interface. • interface port-channel — configures a port channel group.
PAGE 653
Usage Information When you configure keepalive, the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive, the system does not send keepalive packets and so the local end of a WAN link remains up even if the remote end is down. monitor interface Monitor counters on a single interface or all interfaces on a line card. The screen is refreshed every five seconds and the CLI prompt disappears.
PAGE 654
Usage Information Example (Single Interface) Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. In the Example, the delta column displays changes since the last screen refresh. The following are the monitor command menu options. Key Description systest-3 Displays the host name assigned to the system. monitor time Displays the amount of time since the monitor interface command was entered.
PAGE 655
Input giants: Input throttles: Input CRC: Input IP checksum: Input overrun: Output underruns: Output throttles: m l T q Example (All Interfaces) - 0 0 0 0 0 0 0 Change mode Page up Increase refresh interval Quit 0 0 0 0 0 0 0 pps pps pps pps pps pps pps 0 0 0 0 0 0 0 c - Clear screen a - Page down t - Decrease refresh interval systest-3 Monitor time: 00:01:31 Refresh Intvl.
PAGE 656
Parameters value Enter a maximum frame size in bytes. The range is from 594 to 9252 for the S6000. The default is 1554. Defaults 1554 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 657
MTU cannot be higher than 1518 bytes and its IP MTU cannot be higher than 1500 bytes. The following shows the difference between Link MTU and IP MTU. Layer 2 Overhead Link MTU and IP MTU Delta Ethernet (untagged) 18 bytes VLAN Tag 22 bytes Untagged Packet with VLAN-Stack Header 22 bytes Tagged Packet with VLAN-Stack Header 26 bytes negotiation auto Enable auto-negotiation on an interface. S6000 Syntax negotiation auto To disable auto-negotiation, use the no negotiation auto command.
PAGE 658
Usage Information This command is supported on C-Series, S-Series, and E-Series (TeraScale and ExaScale) 10/100/1000 Base-T Ethernet interfaces. The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits. The negotiation auto command provides a mode option for configuring an individual port to forced-master/forced slave after you enable auto-negotiation. NOTE: The mode option is not available on non-10/100/1000 Base-T Ethernet line cards.
PAGE 659
Input Statistics: ... User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces.
PAGE 660
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.
PAGE 661
Native VlanId: 10 Dell(conf-if-vl-20)# Example (Vlan) Dell(conf-if-vl-20)#interface vlan 10 Dell(conf-if-vl-10)#no untagged gi 7/0 Dell(conf-if-vl-10)#interface vlan 20 Dell(conf-if-vl-20)#no tagged gi 7/0 Dell(conf-if-vl-20)#interface gi 7/0 Dell(conf-if-gi-7/0)#no portmode hybrid Dell(conf-if-vl-20)# Related Commands show interfaces switchport — displays the configuration of switchport (Layer 2) interfaces on the switch. switchport — places the interface in a Layer 2 mode.
PAGE 662
Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced Usage Information The output of the show interfaces command displays the configured rate interval, along with the collected traffic data. Related Commands show interfaces — displays information on physical and virtual interfaces. show config Display the interface configuration.
PAGE 663
no shutdown Dell(conf-if-fo-0/4)# show config (for speed) S6000 Syntax show config Command Modes Dell(conf-if-te-2/10)#show config Command History Example Version 9.3(0.1) Introduced on the S6000. Dell(conf-if-te-0/0)#speed ? 10 10 Mbps 100 100 Mbps 1000 1000 Mbps Dell(conf-if-te-0/0)#speed 100 Dell(conf-if-te-2/10)#show config interface TenGigabitEthernet 2/10 speed 100 no shutdown show config (from INTERFACE RANGE mode) Display the bulk configured interfaces (interface range).
PAGE 664
Example Dell(conf)#interface range gigabitethernet 1/1 - 2 Dell(conf-if-range-gi-1/1-2)#show config ! interface GigabitEthernet 1/1 no ip address switchport no shutdown ! interface GigabitEthernet 1/2 no ip address switchport no shutdown Dell(conf-if-range-gi-1/1-2)# show interfaces Display information on a specific physical interface or virtual interface.
PAGE 665
Usage Information Version 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. Version 8.3.11.4 Output expanded to support eSR4 optics in Z9000. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.2 Included SFP and SFP+ optics power detail in the E-Series and C-Series output. Version 8.2.1.0 Added support for 4093 VLANs on the E-Series ExaScale.
PAGE 666
Line Description Hardware is... Interface hardware information, assigned MAC address, and current address. Pluggable media present... Present pluggable media wavelength, type, and rate.
PAGE 667
Line Description – giants = packets that are greater than the MTU size – throttles = packets containing PAUSE frames • Number of CRC, overrun, and discarded packets: – CRC = packets with CRC/FCS errors – overrun = number of packets discarded due to FIFO overrun conditions – discarded = the sum of runts, giants, CRC, and overrun packets discarded without any processing Output Statistics: Displays output statistics sent out of the interface including: • Number of packets, bytes, and underruns out of the
PAGE 668
Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded,
PAGE 669
Time since last interface status change: 1w0d5h Dell# Example (ManagementE thernet) Dell#show interfaces managementethernet 0/0 Example (ManagementE thernet, two IPv6 addresses) Dell#show interfaces managementethernet 0/0 ManagementEthernet 0/0 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:0b:a9:4c Current address is 00:01:e8:0b:a9:4c Pluggable media not present Interface index is 503595208 Internet address is 10.11.201.
PAGE 670
Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example (OpenFlow instance) Dell#show interfaces vlan 6 Vlan 6 is down, line protocol is down Address is 00:01:e8:8a:e1:8c, Current address is 00:01:e8:8a:e1:8c Interface index is 1107525638 of-instance: 2 Internet address is no
PAGE 671
show interfaces configured Display any interface with a non-default configuration. S6000 Syntax show interfaces configured Command Modes • EXEC • EXEC Privilege Command History Example Interfaces Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 672
Time since last interface status change: 00:04:59 Dell# Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces dampening Display interface dampening information. S6000 Syntax Parameters show interfaces dampening [[interface] [summary] [detail]] interface (Optional) Enter one of the following keywords and slot/port or number information: • For a Port Channel interface, enter the keywords portchannel then a number.
PAGE 673
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced Example Dell#show interfaces dampening Interface Supp Flaps Penalty Half-Life Reuse Suppress Max-Sup State Gi 3/2 Up 0 0 20 800 4500 120 Gi 3/10 Up 0 0 5 750 2500 20 Dell# Related Commands dampening — configures dampening on an interface. show interfaces — displays information on a specific physical interface or virtual interface.
PAGE 674
Example Dell#show interfaces stack-unit 0 GigabitEthernet 0/1 is down, line protocol is down Hardware is Force10Eth, address is 00:01:e8:4c:f2:82 Current address is 00:01:e8:4c:f2:82 Pluggable media not present Interface index is 34129154 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto, Mode auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 3w0d17h Queueing strategy: fifo Input Statistics: 0 packets, 0 bytes 5144 64-byte pkts, 0 over 64-byte p
PAGE 675
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then the slot/port information. The range is from 0 to 16383. For a Port-Channel interface, enter the keyword portchannel then the slot/port information. The range is from 0 to 128. • Defaults Command Modes Command History linecard slotnumber (OPTIONAL) Enter the keyword linecard then the slot number.
PAGE 676
Gi 0/11 Gi 0/12 Gi 0/13 Gi 0/14 Gi 0/15 Dell# Related Commands Down Down Down Down Down Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto ----- show interfaces — displays information on a specific physical interface or virtual interface. show interfaces switchport Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode interfaces’ IEEE 802.1Q tag status and VLAN membership.
PAGE 677
Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.2.1.0 Added support for 4093 VLANs on E-Series ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Support added for hybrid port/native VLAN, introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example The following describes the show interfaces switchport command for the following example.
PAGE 678
show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show interfaces transceiver Display the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number.
PAGE 679
Interfaces Line Description Rx Power measurement type Output depends on the vendor, typically either “Average” or “OMA” (Receiver optical modulation amplitude). Temp High Alarm threshold Factory-defined setting, typically in Centigrade. Value differs between SFPs and SFP+. Voltage High Alarm threshold Displays the interface index number used by SNMP to identify the interface. Bias High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 680
Line Description TX Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Temperature Current temperature of the SFPs. If this temperature crosses Temp High alarm/warning thresholds, the temperature high alarm/warning flag is set to true. Voltage Current voltage of the SFPs.
PAGE 681
Interfaces Line Description Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above. Tx Bias High Alarm Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power High Alarm Flag This can be either true or false, depending on the Current Tx bias power value displayed above.
PAGE 682
Example Dell#show interfaces gigabitethernet 1/0 transceiver SFP is present. SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 0x05 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 SFP 0 Serial Base ID fields Id = 0x03 Ext Id = 0x04 Connector = 0x07 Transciever Code = 0x00 0x00 0x00 0x01 0x20 0x40 0x0c Encoding = 0x01 BR Nominal = 0x15 Length(9um) Km = 0x00 Length(9um) 100m = 0x00 Length(50um) 10m = 0x1e Length(62.
PAGE 683
SFP 1 RS state = False SFP 1 Tx Disable state = False =================================== SFP 1 Temperature High Alarm Flag = False SFP 1 Voltage High Alarm Flag = False SFP 1 Tx Bias High Alarm Flag = False SFP 1 Tx Power High Alarm Flag = False SFP 1 Rx Power High Alarm Flag = False SFP 1 Temperature Low Alarm Flag = False SFP 1 Voltage Low Alarm Flag = False SFP 1 Tx Bias Low Alarm Flag = False SFP 1 Tx Power Low Alarm Flag = False SFP 1 Rx Power Low Alarm Flag = True ===================================
PAGE 684
Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced. Example Dell(conf-if-range-so-2/0-1,fa-0/0)#show range interface sonet 2/0 - 1 interface fastethernet 0/0 Dell(conf-if-range-so-2/0-1,fa-0/0)# Related Commands interface — configures a physical interface on the switch. show ip interface — displays Layer 3 information about the interfaces. show interfaces — displays information on a specific physical interface or virtual interface. shutdown Disable an interface.
PAGE 685
Usage Information The shutdown command marks a physical interface as unavailable for traffic. To discover if an interface is disabled, use the show ip interface brief command. Disabled interfaces are listed as down. Disabling a VLAN or a port channel causes different behavior. When a VLAN is disabled, the Layer 3 functions within that VLAN are disabled. Layer 2 traffic continues to flow.
PAGE 686
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.11.1 Introduced on the S55, S60, and S4810 Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Usage Information This command is found on the Management interface only.
PAGE 687
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.1 Introduced on the S4810. Splitting a 40G port into 4x10G port is supported on standalone and stacked units. The quad port must be in a default configuration before it can be split into 4x10G ports. The 40G port is lost in the config when the port is split, so be sure that the port is also removed from other L2/L3 feature configurations.
PAGE 688
remove the backup configuration. To remove a switchport backup interface, enter the no switchport backup interface {gigabit slot/port | tengigabit slot/port | fortyGigE slot/port | port-channel number} command. Parameters backup interface Use this option to configure a redundant Layer 2 link without using Spanning Tree. The keywords backup interface configures a backup port so that if the primary port fails, the backup port changes to the up state. If the primary later comes up, it becomes the backup.
PAGE 689
pre-Version 6.2.1.0 Usage Information Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output. When you enter the switchport command, the interface is automatically added to the default VLAN.
PAGE 690
Parameters interface (OPTIONAL) Enter any of the following keywords and slot/ port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 691
the members have a link MTU of 2100 and an IP MTU 2000, the Port Channel’s MTU values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU. When an interface is removed from a Port Channel with the no channel-member command, the interface reverts to its configuration prior to joining the Port Channel. An interface can belong to only one Port Channel. On the E-Series TeraScale, you can add up to 16 interfaces to a Port Channel; ESeries ExaScale can add up to 64.
PAGE 692
port-channel number Enter the keywords port-channel then an existing LAG number. Enter this keyword/variable combination twice, identifying the two paired LAGs. Defaults none Command Modes PORT-CHANNEL FAILOVER-GROUP (conf-po-failover-grp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 693
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on S4810. Version 8.3.11.1 Introduced on Z9000. Version 8.1.1.0 Introduced on E-Series ExaScale. Version 7.6.1.
PAGE 694
Example Dell(conf)#int port-channel 2 Dell(conf-if-po-2)# Related Commands channel-member — adds a physical interface to the LAG. interface — configures a physical interface. interface loopback — configures a Loopback interface. interface null — configures a null interface. interface vlan — configures a VLAN. shutdown — disables/enables the port channel.
PAGE 695
pre-Version 6.2.1.0 Usage Information Introduced on the E-Series. If you use this command to configure the minimum number of links in a LAG that must be in “oper up” status, the LAG must have at least that number of “oper up” links before it can be declared as up. For example, if the required minimum is four, and only three are up, the LAG is considered down. port-channel failover-group To configure a LAG failover group, access PORT-CHANNEL FAILOVER-GROUP mode.
PAGE 696
show interfaces port-channel — displays information on configured Port Channel groups. show interfaces port-channel Display information on configured Port Channel groups. S6000 Syntax Parameters show interfaces port-channel [channel-number] [brief] channelnumber For a Port Channel interface, enter the keyword portchannel then a number. For the C-Series and S-Series, the range is from 1 to 128.
PAGE 697
Example Interfaces Field Description Hardware is... Displays the interface’s hardware information and its assigned MAC address. Port-channel is part... Indicates whether the LAG is part of a LAG fate-sharing group (“Failover-group”). Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed. MTU 1554... Displays link and IP MTU. LineSpeed Displays the interface’s line speed.
PAGE 698
LineSpeed 2000 Mbit Members in this channel: Gi 0/5 Gi 0/18 ARP type: ARPA, ARP timeout 04:00:00 Last clearing of "show interfaces" counters 00:00:00 Queueing strategy: fifo 44507301 packets input, 3563070343 bytes Input 44506754 IP Packets, 0 Vlans 0 MPLS 41 64-byte pkts, 44502871 over 64-byte pkts, 249 over 127byte pkts 407 over 255-byte pkts, 3127 over 511-byte pkts, 606 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 1218120
PAGE 699
Gi 3/1 (Down) Gi 3/2 (Up) Dell# Related Commands show lacp — displays the LACP matrix. show port-channel-flow Display an egress port in a given port-channel flow.
PAGE 700
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.0 Introduced on the S4810.
PAGE 701
Enhanced Validation of Interface Ranges This functionality is supported on the S6000 platform. You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as interface range fo 2/0-1,te 10/0,gi 3/0,fa 0/0, this configuration is considered valid. The comma-separated list is not required to be separated by spaces in between the ranges.
PAGE 702
Command History Related Commands 702 Version 9.3(0.1) Introduced on the S4810, S4820T, S6000, and Z9000. Version 8.3.11.1 Introduced on the Z9000 Version 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094) Version 8.1.1.0 Introduced on E-Series ExaScale Version 7.6.1.0 Support added for S-Series Version 7.5.1.0 Introduced on C-Series ip ftp source interface Configuring source interface for ftp communications.
PAGE 703
23 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the S6000 platform. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). S6000 Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 704
Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 705
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer.
PAGE 706
1. At time t=0, Dell Networking OS sends an ARP request for IP A.B.C.D. 2. At time t=1, Dell Networking OS receives an ARP request for IP A.B.C.D. 3. At time t=2, Dell Networking OS installs an ARP entry for A.B.C.D only on RP2. Beginning with Dell Networking OS version 8.3.1.0, when a gratuitous ARP is received, Dell Networking OS installs an ARP entry on all three CPUs. arp max-entries Enables you to configure the maximum number of ARP entries per VRF that are allowed for IPv4..
PAGE 707
arp retries Set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. S6000 Syntax arp retries number Parameters number Enter the number of retries. The range is from 1 to 20. The default is 5. Defaults 5 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 708
Defaults 240 minutes (4 hours) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 709
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. ip ip-address (OPTIONAL) Enter the keyword ip then the IP address of the ARP entry you wish to clear. no-refresh (OPTIONAL) Enter the keywords no-refresh to delete the ARP entry from CAM. Or use this option with interface or ip ip-address to specify which dynamic ARP entries you want to delete.
PAGE 710
clear host Remove one or all dynamically learned host table entries. S6000 Syntax Parameters clear host name name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 711
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.19.0 Introduced on the S4820T. Usage Information To clear Layer 3 CAM inconsistencies, use this command. Related Commands show ip fib stack-unit — shows FIB entries on a specified stack-unit. CAUTION: Executing this command causes traffic disruption.
PAGE 712
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Use the vrf vrf-name attribute of this command to clear routes corresponding to either a specific VRF or the default VRF. You cannot use this attribute to clear routes corresponding to a management VRF.
PAGE 713
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. debug arp View information on ARP transactions. S6000 Syntax debug arp [interface] [count value] To stop debugging ARP transactions, use the no debug arp command.
PAGE 714
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.
PAGE 715
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.10 Introduced on the E-Series. Example Dell#debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.
PAGE 716
ip helper-address hop-count disable – disables the hop-count increment for the DHCP relay agent. debug ip icmp View information on the internal control message protocol (ICMP). S6000 Syntax debug ip icmp [interface] [count value] To disable debugging, use the no debug ip icmp command. Parameters interface count value (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 717
Example Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Added the count option.
PAGE 718
• For the Management interface, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1 and the port range is 0. • For a Port Channel interface, enter the keywords portchannel then a number. For the C-Series and S-Series, the range is from 1 to 128. • For a SONET interface, enter the keyword sonet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 719
Field Description d= Lists the destination address of the packet and the name of the interface (in parentheses) through which the packet is being sent out on the network. len Displays the packet’s length. sending, rcvd, fragment, sending broad/multicast proto, unroutable The last part of each line lists the status of the packet. TCP src= Displays the source and destination ports, the sequence number, the acknowledgement number, and the window size of the packets in that TCP packets.
PAGE 720
The access-group option supports only the equal to (eq) operator in TCP ACL rules. Port operators not equal to (neq), greater than (gt), less than (lt), or range are not supported in access-group option (refer to the following example). ARP packets (arp) and Ether-type (ether-type) are also not supported in the accessgroup option. The entire rule is skipped to compose the filter.
PAGE 721
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.
PAGE 722
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. ip domain-list Configure names to complete unqualified host names. S6000 Syntax ip domain-list name To remove the name, use the no ip domain-list name command.
PAGE 723
the name is not resolved, the software goes through the list of names configured with the ip domain-list command to find a match. To enable dynamic resolution of hosts, use the following steps: • specify a domain name server with the ip name-server command • enable DNS with the ip domain-lookup command To view current bindings, use the show hosts command. To view a DNS-related configuration, use the show running-config resolve command. Related Commands ip domain-name — specifies a DNS server.
PAGE 724
Dell Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out all other interfaces, including the Management port. To view current bindings, use the show hosts command. Related Commands ip name-server — specifies a DNS server. show hosts — Views the current bindings. ip domain-name Configure one domain name for the switch. S6000 Syntax ip domain-name name To remove the domain name, use the no ip domain-name command.
PAGE 725
Usage Information You can only configure one domain name with the ip domain-name command. To configure more than one domain name, configure the ip domain-list command up to six times. To enable dynamic resolution of hosts, use the following steps: • specify a domain name server with the ip name-server command • enable DNS with the ip domain-lookup command To view current bindings, use the show hosts command. Related Commands ip domain-list — configures additional names.
PAGE 726
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. You can add multiple DHCP servers by entering the ip helper-address command multiple times. If multiple servers are defined, an incoming request is sent simultaneously to all configured servers and the reply is forwarded to the DHCP client.
PAGE 727
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced for the E-Series. Usage Information This command disables the incrementing of the hops field when boot requests are relayed to a DHCP server through Dell Networking OS. If the incoming boot request already has a non-zero hops field, the message is relayed with the same value for hops.
PAGE 728
Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced for the E-Series.
PAGE 729
Command Modes Command History Usage Information CONFIGURATION Version 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 platforms. You can enable the mechanism to configure the source or the originating interface from which the packet (the device that generates the ICMP error messages) is received by the switch to send the loopback address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output.
PAGE 730
NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
PAGE 731
Example Dell(conf)#ipv6 icmp source-interface tengigabitethernet 0/0 Dell(conf)# ip max-frag-count Set the maximum number of fragments allowed in one packet for packet re-assembly. S6000 Syntax ip max-frag-count count To place no limit on the number of fragments allowed, use the no ip max-fragcount command. Parameters count Enter a number for the number of fragments allowed for reassembly. The range is from 2 to 256. Defaults No limit is set on number of fragments allowed.
PAGE 732
ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. S6000 Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command. Parameters ipv4-address Enter the IPv4 address, in dotted decimal format, of the name server to be used. ipv4-address2...
PAGE 733
ip proxy-arp Enable proxy ARP on an interface. S6000 Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 734
To delete all routes matching a certain route, use the no ip route destination mask command. Parameters vrf vrf-name (Optoinal) Enter the keyword vrf and then the name of the VRF to configure a static route corresponding to that VRF. Use this VRF option after the ip route keyword to configure a static route on that particular VRF. destination Enter the IP address in dotted decimal format of the destination device. mask Enter the mask in the slash prefix format (/x) of the destination IP address.
PAGE 735
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 736
Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 737
a SYN ACK, the router waits for a period of time for the ACK packet to be sent from the requesting host that will establish the TCP connection. ip unknown-unicast Enable IPv4 catch-all route. S6000 Syntax ip unknown-unicast [vrf vrf-name] To remove the IPv4 catch-all route (0.0.0.0/0) from the LPM route forwarding table in hardware which gets added as a default configuration after the initialization of FIB Agent module, use the no ip unknown-unicast command.
PAGE 738
Usage Information A warning message is displayed when you enter this command stating that this setting takes effect for existing routes only when IPv4 route prefixes are cleared from the routing table (RTM). To disable this functionality, use no ipv4 unicasthost-route command.
PAGE 739
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 740
mac {dest-mac | source-destmac | sourcemac} tcp-udp enable Enter the keywords to distribute MAC traffic based on the following criteria: • dest-mac — Uses the destination MAC address, VLAN, Ethertype, source module ID and source port ID fields to hash. The hashing mechanism returns a 3-bit index indicating which port the packet should be forwarded. • source-dest-mac — Uses the destination and source MAC address, VLAN, Ethertype, source module ID and source port ID fields to hash.
PAGE 741
Version 7.5.1.0 Usage Information Introduced on the C-Series. By default, Dell Networking OS distributes incoming traffic based on a hash algorithm using the following criteria: • • • • IP source address IP destination address TCP/UDP source port TCP/UDP destination port load-balance hg Choose the traffic flow parameters the hash calculation uses while distributing the traffic across internal higig links.
PAGE 742
mac [sourcemac | sourceport-id | sourcemodule-id | dest-mac | dest-port-id | dest-moduleid | vlan | ethertype | source-destmac ] tunnel [ipv4over-ipv4 | ipv4-over-greipv4 | mac-inmac]} To use MAC key fields in hash computation, enter the keyword mac then one of the parameters: • source-mac — Use source-mac field in hash calculation. • source-port-id — Use src-port-id field in hash calculation. • source-module-id — Use src-module-id field in hash calculation.
PAGE 743
management route Configure a static route that points to the Management interface or a forwarding router. S6000 Syntax management route {{ip-address mask | {ipv6-address prefixlength}} {forwarding-router-address | managementethernet} To remove a static route, use the no management route{{ip-address mask | {ipv6-address prefix-length}}{forwarding-router-address | managementethernet} command.
PAGE 744
pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix are not reflected in the hardware routing tables. Separate routing tables are maintained for IPv4 and IPv6 management routes. This command manages both tables.
PAGE 745
ip ip-address mask (OPTIONAL) Enter the keyword ip then an IP address in the dotted decimal format. Enter the optional IP address mask in the slash prefix format (/ x). inspection Enter the keyword inspection with one of the following keywords to view ARP entries: • database — view a list of ARP entries learned using DAI • statistics — view DAI statistics macaddress mac-address mask (OPTIONAL) Enter the keyword macaddress then a MAC address in nn:nn:nn:nn:nn:nn format.
PAGE 746
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The following example shows two VLANs that are associated with a private VLAN (PVLAN) (refer to Private VLAN (PVLAN)).
PAGE 747
Internet 10 Internet Internet Internet Internet Internet Usage Information 5.5.5.10 CP 10.1.2.4 CP 10.10.10.4 CP 10.16.127.53 CP 10.16.134.254 CP 133.33.33.4 CP - 00:01:e8:44:99:55 - 1 00:01:e8:d5:9e:e2 Ma 0/0 1 00:01:e8:d5:9e:e2 Ma 0/0 1 00:01:e8:d5:9e:e2 Ma 0/0 20 00:01:e8:d5:9e:e2 Ma 0/0 1 Ma 0/0 00:01:e8:d5:9e:e2 Vl The following describes the show arp summary command shown in the following example. Description Total Entries Lists the total number of ARP entries in the ARP table.
PAGE 748
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced. arp retries — sets the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. show hosts View the host table and DNS configuration. S6000 Syntax show hosts Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 749
Field Description Name/address lookup... States if DNS is enabled on the system. • If DNS is enabled, the Name/Address lookup is domain service. • If DNS is not enabled, the Name/Address lookup is static mapping Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address.
PAGE 750
show ip cam stack-unit Display CAM entries for an S-Series or Z-Series switch. S6000 Syntax Parameters show ip cam stack-unit {id} [port-set {pipe-number} | hostname {ip-address mask [longer-prefixes [ecmp-group detail]]}| ecmpgroup {detail | member-info [detail [group-index indexnumber]]}| summary] id Enter the stack-unit ID. The unit ID range is from 0 to 7 for the S6000. port-set pipenumber Enter the keyword port-set then the number of the stack unit’s port-pipe.
PAGE 751
The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for up to seven stack members. Version 7.6.1.0 Introduced on the S-Series. The following describes the show ip cam command shown in the following example. Field Description Destination Displays the destination route of the index.
PAGE 752
Field Description Prefix Length Displays the prefix-length or mask for the IP address configured on the linecard 0 port pipe 0. Current Use Displays the number of routes currently configured for the corresponding prefix or mask on the linecard 0 port pipe 0. Initial Size Displays the CAM size Dell Networking OS allocates for the corresponding mask. Dell Networking OS adjusts the CAM size if the number of routes for the mask exceeds the initial allocation.
PAGE 753
longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. summary (OPTIONAL) Enter the keyword summary to view the total number of prefixes in the FIB. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 754
BLK HOLE 0 0 Dell> Related Commands clear ip fib stack-unit — clear FIB entries on a specified stack-unit. show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface. S6000 Syntax Parameters show ip flow interface interface {source-ip address destination-ip address} {protocol number [tcp | udp]} {src-port number destination-port number} interface interface Enter the keyword interface then one of the following interface keywords.
PAGE 755
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 756
Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information, the valid range of slot number is from 0 to 5: • For a Loopback interface, enter the keyword Loopback then a number from 0 to 16383. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For the Management interface, enter the keyword ManagementEthernet then zero (0). • For the Null interface, enter the keyword null then zero (0).
PAGE 757
Usage Information Example Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.2 Supported on the E-Series ExaScale E600i. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The following describes the show ip interface command shown in the following example. Lines Description TenGigabitEthern et 0/0...
PAGE 758
Example (Brief) Fields Description Interface Displays type of interface and the associated slot and port number. IP-Address Displays the IP address for the interface, if configured. Ok? Indicates if the hardware is functioning properly. Method Displays “Manual” if the configuration is read from the saved configuration. Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface.
PAGE 759
static (OPTIONAL) Enter the keyword static to view non-active routes also. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 760
summary (OPTIONAL) Enter the keyword summary to view a table listing the number of active and non-active routes and their sources. static (OPTIONAL) Enter the keyword static to view non-active routes also. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 761
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Regular evaluation optimization enabled/disabled added to display output. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 762
ip-address (OPTIONAL) Specify a name of a device or the IP address of the device to view more detailed information about the route. mask (OPTIONAL) Specify the network mask of the route. Use this parameter with the IP address parameter. longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. list prefix-list (OPTIONAL) Enter the keyword list and the name of a configured prefix list. For more information, refer to the show ip route list command.
PAGE 763
Usage Information IPv4 Routing Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 764
Example Field Description Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured.
PAGE 765
C Destination ----------13.0.0.0/24 Gateway Dist/Metric Last Change ----------------- ----------Direct, Te 0/17 0/0 00:00:04 show ip route list Display IP routes in an IP prefix list. S6000 Syntax Parameters show ip route list prefix-list prefix-list Enter the name of a configured prefix list. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 766
Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.0/24 2.1.3.0/24 2.1.4.0/24 Gateway ------via 2.1.4.1, Gi via 2.1.4.1, Gi via 2.1.4.1, Gi via 2.1.4.1, Gi Direct, Gi 4/43 4/43 4/43 4/43 4/43 Dist/Metric Last Change ----------- ----------120/2 3d0h 120/2 3d1h 120/1 3d0h 120/1 3d1h 0/0 3d1h ip prefix-list — enters CONFIGURATION-IP PREFIX-LIST mode and configures a prefix list.
PAGE 767
Usage Information Example The following describes the show ip route summary shown in the following example. Column Heading Description Route Source Identifies how the route is configured in Dell Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources. Non-active Routes Identifies the back-up routes when a route is learned by two different protocols. If the best route or active route goes down, the non-active route becomes the best route.
PAGE 768
cp (OPTIONAL) Enter the keyword cp to view only statistics from the Control Processor. rp1 (OPTIONAL) Enter the keyword rp1 to view only the statistics from Route Processor 1. rp2 (OPTIONAL) Enter the keyword rp2 to view only the statistics from Route Processor 2. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 769
Keyword Definition Frags: IP fragments received. ... reassembled Number of IP fragments that were reassembled. ... timeouts Number of times a timer expired on a reassembled queue. ... too big Number of invalid IP fragments received. ... couldn’t fragment Number of packets that could not be fragmented and forwarded. ...encapsulation failed Counts packets which could not be forwarded due to ARP resolution failure. Dell Networking OS sends an arp request prior to forwarding an IP packet.
PAGE 770
0 unknown protocol, 0 not a gateway 0 security failures, 0 bad options Frags: 0 reassembled, 0 timeouts, 0 too big 0 fragmented, 0 couldn't fragment Bcast: 28 received, 0 sent; Mcast: 0 received, 0 sent Sent: 16048 generated, 0 forwarded 21 encapsulation failed, 0 no route ICMP statistics: Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0 unreachable 0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench 0 parameter, 0 timestamp, 0 info request, 0 other Sent: 0 redirects, 0 unreachable, 0 ec
PAGE 771
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 6.4.1.0 Introduced The following describes the show tcp statistics cp command shown in the following example. Field Description Rcvd: Displays the number and types of TCP packets received by the switch. 0 checksum error...
PAGE 772
Example Field Description Sent: Displays the total number of TCP packets sent and the number of urgent packets sent. 25 control packets... Displays the number of control packets sent and the number retransmitted. 11603 data packets... Displays the number of data packets sent. 24 data packets retransmitted Displays the number of data packets resent. 355 ack.. Displays the number of acknowledgement packets sent and the number of packet delayed. 0 window probe...
PAGE 773
dropped in keepalive Dell# Related Commands IPv4 Routing show ip cam stack-unit — displays the CAM table.
PAGE 774
24 IPv6 Basics IPv6 basic commands are supported on the Dell Networking platform. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide. cam-ipv6 extended-prefix Enable LPM partitioning to support IPv6 /65 to /128 route prefixes to be stored in Partition 1.
PAGE 775
show cam-ipv6 extended-prefix Display the current settings and next-boot settings for cam-ipv6 extended-prefix configuration. Display the cam-ipv6 extended-prefix configuration. S6000 Syntax show cam-ipv6 extended-prefix Defaults None Command Modes EXEC Command History EXEC Privilege Version 9.3(0.1) Introduced on the S6000. Usage Information You can use this command to view the number of supported extended prefix entries in LPM configured.
PAGE 776
when IPv6 route prefixes are cleared from RTM Dell(conf)#no ipv6 unicast-host-route Warning: Command will take effect for existing routes only when IPv6 route prefixes are cleared from RTM Dell(conf)# ipv6 nd dns-server Configures Recursive DNS Server (RDNSS) addresses to be distributed via IPv6 router advertisements to an IPv6 device.
PAGE 777
Usage Information Use this command to add, edit, or delete an IPv6 RDNSS address and lifetime value. You can configure up to four IPv6 RDNSS addresses. You must specify a lifetime using the lifetime or infinite parameter.
PAGE 778
IPv6 Access Control Lists (IPv6 ACLs) 25 IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking platform. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl command. • Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. • Reference to an empty ACL permits any traffic.
PAGE 779
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.8.1.0 Introduced on the C-Series.
PAGE 780
Example Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.8.1.0 Introduced on the C-Series.
PAGE 781
permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter. S6000 Syntax permit icmp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [count [byte]] To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit icmp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command.
PAGE 782
permit To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP. S6000 Syntax permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command ip-protocolnumber Enter an IPv6 protocol number. The range is from 0 to 255.
PAGE 783
ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. S6000 Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 784
ospfv3 Specify that this ACL is for OSPFv3 control plane traffic Defaults All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4(0.
PAGE 785
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 • L3 ACL (ipv4acl: 1 • IPv6 L3 ACL (ipv6acl): 2 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 786
cam-acl Allocate space for IPv6 ACLs. S6000 Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: • • • • • l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 L3 ACL (ipv4acl): 6 L2 ACL(l2acl): 5 IPv6 L3 ACL (ipv6acl): 0 L3 QoS (ipv4qos): 1 L2 QoS (l2qos): 1 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 787
Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10).
PAGE 788
Intermediate System to Intermediate System (IS-IS) 26 The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the S6000platform. IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing both IP and OSI traffic. A router is considered an intermediate system. Networks are partitioned into manageable routing domains, called areas.
PAGE 789
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabled by default. advertise Leak routes between levels (distribute IP prefixes between Level 1 and Level 2 and vice versa).
PAGE 790
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Added IPv6 ISIS support. Version 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from one level to another; however, you can regulate the rate flow from one level to another using an IP Prefix list. If you do not configure the IP Prefix list, all routes are leaked. You can find more information in IETF RFC 2966, Domain-wide Prefix Distribution with Two-Level IS-IS.
PAGE 791
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands • domain-password — allows you to set the authentication password for a routing domain.
PAGE 792
clear isis Restart the IS-IS process. All IS-IS data is cleared. S6000 Syntax Parameters clear isis [tag] {* | database | traffic} tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters.
PAGE 793
nsap Enter a specific NSAP address that is associated with the name parameter. Defaults Not configured. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 794
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Entering debug isis enables all debugging parameters. To display all debugging information in one output, use this command. To turn off debugging, you normally enter separate no forms of each command. To disable all debug messages for IS-IS at once, enter the no debug isis command.
PAGE 795
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information. S6000 Syntax debug isis local-updates [interface] To turn off debugging, use the no debug isis local-updates [interface] command.
PAGE 796
Version 8.3.12.0 Introduced on the S4810. Version 6.3.1.0 Introduced. debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. S6000 Syntax debug isis snp-packets [interface] To turn off debugging, use the no debug isis snp-packets [interface] command.
PAGE 797
Version 6.3.1.0 Introduced. debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. S6000 Syntax debug isis spf-triggers To turn off debugging, use the no debug isis spf-triggers command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 798
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094.
PAGE 799
route-map map-name (OPTIONAL) A default route the routing process generates if the route map is satisfied. Defaults Not configured. Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 800
description Enter a description of the IS-IS routing protocol. S6000 Syntax description {description} To remove the description, use the no description {description} command. Parameters description Defaults none Command Modes ROUTER ISIS Command History Related Commands Enter a description to identify the IS-IS protocol (80 characters maximum). Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.
PAGE 801
ip-address mask (OPTIONAL) Enter an IP address in dotted decimal format and enter a mask in either dotted decimal or /prefix format. prefix-list (OPTIONAL) Enter the name of a prefix list name. Defaults weight = 115 Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 802
• For a 1- Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a SONET interface, enter the keyword sonet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 803
To return to the default values, use the no distribute-list prefix-listname out [bgp as number connected | ospf process-id | rip | static] command. Parameters prefix-listname Specify the prefix list to filter prefixes in routing updates. connected (OPTIONAL) Enter the keyword connected for directly connected routing process. ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number.
PAGE 804
distribute-list redistributed-override Suppress flapping of routes when the same route is redistributed into IS-IS from multiple routers in the network. S6000 Syntax distribute-list redistributed-override in To return to the default, use the no distribute-list redistributedoverride in command. Defaults none Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific.
PAGE 805
Parameters hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. encryptiontype (OPTIONAL) Enter 7 to encrypt the password using DES. password Enter an alphanumeric string up to 16 characters long. If you do not specify an encryption type or hmac-md5 keywords, the password is processed as plain text which provides limited security. Defaults No default password. Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 806
Parameters ietf Enter ietf to enable graceful restart on the IS-IS router. Defaults Graceful restart disabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 807
Defaults 5 minutes Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.
PAGE 808
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. graceful-restart t3 — configures the overall wait time before graceful restart completes. graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated.
PAGE 809
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize. S6000 Syntax graceful-restart t2 {level-1 | level-2} seconds To return to the default, use the no graceful-restart t2 command.
PAGE 810
graceful-restart t3 Configure the overall wait time before graceful restart completes. S6000 Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command. Parameters adjacency Enter the keyword adjacency so that the restarting router receives the remaining time value from its peer and adjusts its T3 value so if you have configured this option. manual Enter the keyword manual to specify a time value that the restarting router uses.
PAGE 811
Related Commands graceful-restart restart-wait — enables the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. S6000 Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | pointto-point] command.
PAGE 812
hostname dynamic Enables dynamic learning of hostnames from routers in the domain and allows the routers to advertise the hostname in LSPs. S6000 Syntax hostname dynamic To disable this command, use the no hostname dynamic command. Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 813
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000.
PAGE 814
Usage Information Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced. To assign a network entity title to enable IS-IS, use the net command. • net — configures an IS-IS network entity title (NET) for the routing process. • router isis — enables the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process.
PAGE 815
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced on the E-Series. Configure a network entity title (the net command) to specify the area address and the router system ID. To establish adjacencies and establish dynamic routing, enable routing on one or more interfaces. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 816
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Because the default establishes Level 1 and Level 2 adjacencies, you do not need to configure this command. Routers in an IS-IS system must be configured as a Level 1-only, Level 1-2, or Level 2-only system.
PAGE 817
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. The default values of this command are typically satisfactory transmission times for a specific interface on a designated intermediate system. To maintain database synchronization, the designated routers send CSNPs. You can configure Level 1 and Level 2 CSNP intervals independently.
PAGE 818
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information Hello packets are held for a length of three times the value of the hello interval. To conserve bandwidth and CPU usage, use a high hello interval seconds. Use a low hello interval seconds for faster convergence (but uses more bandwidth and CPU resources).
PAGE 819
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information The holdtime (the product of the hello-multiplier multiplied by the hello-interval) determines how long a neighbor waits for a hello packet before declaring the neighbor is down so routes can be recalculated. Related Commands isis hello-interval — specifies the length of time between hello packets.
PAGE 820
Related Commands hello padding — turns ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information. S6000 Syntax isis ipv6 metric default-metric [level-1 | level-2] To return to the default values, use the no ipv6 isis metric [defaultmetric] [level-1 | level-2] command. Parameters default-metric Metric assigned to the link and used to calculate the cost from each other router via the links in the network to other destinations.
PAGE 821
Usage Information Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis metric Assign a metric to an interface. S6000 Syntax isis metric default-metric [level-1 | level-2] To return to the default values, use the no isis metric [default-metric] [level-1 | level-2] command.
PAGE 822
Usage Information Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis network point-to-point Enable the software to treat a broadcast interface as a point-to-point interface. S6000 Syntax isis network point-to-point To disable the feature, use the no isis network point-to-point command. Defaults Not enabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 823
Parameters encryptiontype (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password. level-1 (OPTIONAL) Independently configures the authentication password for Level 1. The router acts as a station router for Level 1 routing. This setting is the default. level-2 (OPTIONAL) Independently configures the authentication password for Level 2.
PAGE 824
isis priority Set the priority of the designated router you select. S6000 Syntax isis priority value [level-1 | level-2] To return to the default values, use the no isis priority [value] [level-1 | level-2] command. Parameters value This value sets the router priority. The higher the value, the higher the priority. The range is from 0 to 127. The default is 64. level-1 (OPTIONAL) Specify the priority for Level 1. This setting is the default. level-2 (OPTIONAL) Specify the priority for Level 2.
PAGE 825
is-type Configure IS-IS operating level for a router. S6000 Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. Defaults level-1-2 Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 826
log-adjacency-changes Generate a log messages for adjacency state changes. S6000 Syntax log-adjacency-changes To disable this function, use the no log-adjacency-changes command. Defaults Adjacency changes are not logged. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 827
level-2 (OPTIONAL) Enter the keywords level-2 to apply the configuration to generation of Level-2 LSPs. interval seconds Enter the maximum number of seconds between LSP generations. The range is from 0 to 120 seconds. The default is 5 seconds. initial_wait_inte rval seconds (OPTIONAL) Enter the initial wait time, in seconds, before running the first LSP generation. The range is from 0 to 120 seconds. The default is 1 second.
PAGE 828
lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. S6000 Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 128 to 1497 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497. Defaults 1497 bytes. Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 829
lsp-refresh-interval Set the link state PDU (LSP) refresh interval. LSPs must be refreshed before they expire. When the LSPs are not refreshed after a refresh interval, they are kept in a database until their max-lsp-lifetime reaches zero and then LSPs is purged. S6000 Syntax lsp-refresh-interval seconds To restore the default refresh interval, use the no lsp-refresh-interval command. Parameters seconds The LSP refresh interval, in seconds.
PAGE 830
max-area-addresses Configure manual area addresses. S6000 Syntax max-area-addresses number To return to the default values, use the no max-area-addresses command. Parameters number Set the maximum number of manual area addresses. The range is from 3 to 6. The default is 3. Defaults 3 addresses Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 831
Parameters seconds The maximum lifetime of LSP in seconds. This value must be greater than the lsp-refresh-interval command. The higher the value the longer the LSPs are kept. The range is from 1 to 65535. The default is 1200. Defaults 1200 seconds Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 832
Defaults Command Modes Command History 4 • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.
PAGE 833
Defaults narrow; if no Level is specified, Level-1 and Level-2 are configured. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 834
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Introduced. net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start.
PAGE 835
passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. S6000 Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 836
redistribute Redistribute routes from one routing domain to another routing domain. S6000 Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] To end redistribution or disable any of the specified keywords, use the no redistribute {static | connected | rip} [metric metric-value] [metric-type {external | internal}] [level-1 | level-1-2 | level-2] [route-map map-name] command.
PAGE 837
• Command History CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810.
PAGE 838
redistribute bgp Redistribute routing information from a BGP process. S6000 Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value] [metric-type {external| internal}] [route-map map-name] To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter a number that corresponds to the autonomous system number. The range is from 1 to 65355.
PAGE 839
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.5.1.0 Added support for IPv6 ISIS. Version 6.3.1.0 Introduced. Usage Information BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command. You can “set” more advanced options using route maps.
PAGE 840
metric-type {external | internal} (OPTIONAL) The external link type associated with the default route advertised into a routing domain. The two options are: • external • internal level-1 (OPTIONAL) Routes are independently redistributed into ISIS as Level 1 routes. level-1-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level-1-2 routes. level-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level 2 routes. This setting is the default.
PAGE 841
Usage Information How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command. If the metric-style command is set for Narrow mode and the metric value in the redistribute ospf command is set to a number higher than 63, the metric value advertised in LSPs is 63. If the metric-style command is set for wide mode, the metric value in the redistribute ospf command is advertised.
PAGE 842
You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time. Related Commands • ip router isis — configures IS-IS routing processes for IP on interfaces and attaches an area designator to the routing process. • net — configures an IS-IS network entity title (NET) for a routing process. • is-type — assigns a type for a given area.
PAGE 843
show config Display the changes you made to the IS-IS configuration. Default values are not shown. S6000 Syntax show config Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 844
show isis database Display the IS-IS link state database. S6000 Syntax Parameters show isis database [level-1 | level-2] [local] [detail | summary] [lspid] level-1 (OPTIONAL) Displays the Level 1 IS-IS link-state database. level-2 (OPTIONAL) Displays the Level 2 IS-IS link-state database. local (OPTIONAL) Displays local link-state database information. detail (OPTIONAL) Detailed link-state database information of each LSP displays when specified. If not specified, a summary displays.
PAGE 845
Field Description The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID. If this byte is not zero, the LSP describes system links. If this byte is zero (0), the LSP describes the state of the originating router. The designated router for a LAN creates and floods a pseudonode LSP and describes the attached systems. The last octet is the LSP number.
PAGE 846
ISIS.00-00 * 0x00000006 0xCF43 580 ! FTOS#show isis database detail ISIS.00-00 0/0/0 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002B 0x853B 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.1 IPv6 Address: 1011::1 Topology: IPv4 (0x00) IPv6 (0x8002) Metric: 10 IS OSPF.00 Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.
PAGE 847
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series.
PAGE 848
The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. FTOS#show isis hostname System Id Dynamic Name Static Name *F100.E120.0013 Force10 ISIS FTOS# show isis interface Display detailed IS-IS interface status and configuration information.
PAGE 849
Example Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. FTOSF>show isis int GigabitEthernet 0/7 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 37847070, Local circuit ID 1 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 850
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 851
Example Field Description Circuit Id The neighbor’s interpretation of the designated router for the interface. The bold sections below identify that Multi-Topology IS-IS is enabled. FTOS#show isis neighbors System Id Interface State Type Priority Uptime Circuit Id TEST Gi 7/1 Up L1L2(M) 127 09:28:01 TEST.02 ! FTOS#show isis neighbors detail System Id Interface State Type Priority Uptime Circuit Id TEST Gi 7/1 Up L1L2(M) 127 09:28:04 TEST.02 Area Address(es): 49.0000.0001 IP Address(es): 25.1.1.
PAGE 852
System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.0000.0001 Routing for area address(es): 49.0000.0001 Interfaces supported by IS-IS: GigabitEthernet 1/0 - IP - IPv6 GigabitEthernet 1/1 - IP - IPv6 GigabitEthernet 1/10 - IP - IPv6 Loopback 0 - IP - IPv6 Redistributing: Distance: 115 Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode.
PAGE 853
Usage Information Example Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. The following describes the show isis traffic command shown in the following example. Item Description Level-1/Level-2 Hellos (sent/rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/ rcvd) Displays the number of point-to-point Hellos sent and received.
PAGE 854
IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: FTOS# Level-2 LSPs CSNPs (sent/rcvd) : 472/238 Level-1 LSPs PSNPs (sent/rcvd) : 0/0 Level-2 LSPs PSNPs (sent/rcvd) : 10/337 Level-1 DR Elections : 4 Level-2 DR Elections : 4 Level-1 SPF Calculations : 0 Level-2 SPF Calculations : 389 LSP checksum errors received : 0 LSP authentication failures : 0 spf-interval Specify the minimum interval between shortest path first (SPF) calculations.
PAGE 855
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Added support for multi-topology ISIS. Version 7.5.1.0 Added support for SPF Throttling Enhancement. This command spf-interval in CONFIG-ROUTER-ISIS-AF-IPV6 mode is used for IPv6 Multi-Topology route computation only.
PAGE 856
27 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. The LACP commands in this chapter are supported by Dell Networking OS on the S6000 platform.
PAGE 857
Version 6.2.1.1 Related Commands Introduced on the E-Series. show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). S6000 Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command. Parameters config (OPTIONAL) Enter the keyword config to debug the LACP configuration.
PAGE 858
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 859
Related Commands show lacp — displays the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority. S6000 Syntax lacp port-priority priority-value To return to the default setting, use the no lacp port-priority priorityvalue command. Parameters priority-value Enter the port-priority value. The higher the value number, the lower the priority.
PAGE 860
lacp system-priority Configure the LACP system priority. S6000 Syntax Parameters lacp system-priority priority-value priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. Defaults 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 861
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.1 Introduced on the E-Series.
PAGE 862
Example (PortChannelNumber) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.1 Introduced on the E-Series. Dell#show lacp Port-channel 1 Actor System Partner System Key 1 1 admin up, oper up, ID:Priority 32768, ID:Priority 32768, Actor Admin Key mode lacp Address 0001.e800.
PAGE 863
28 Layer 2 This chapter describes commands to configure Layer 2 features. This chapter contains the following sections: • MAC Addressing Commands • Virtual LAN (VLAN) Commands • The VLAN commands are supported on all the S6000 platform. MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 864
Related Commands Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. mac learning-limit — sets the MAC address learning limits for a selected interface.
PAGE 865
vlan vlan-id • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Enter the keyword vlan then a VLAN ID number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 866
mac-address-table station-move refresh-arp Ensure that address resolution protocol (ARP) refreshes the egress interface when a station move occurs due to a topology change. S6000 Syntax [no] mac-address-table station-move refresh-arp Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 867
station-moveviolation Defaults • (OPTIONAL) Enter the keywords station-move to allow a station move on learned MAC addresses. On S-Series, the default behavior is dynamic. NOTE: “Static” means manually entered addresses, which do not age. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 868
After the MAC address learning limit is reached, the MAC addresses do not age out unless you add the dynamic option. To clear statistics on MAC address learning, use the clear counters command with the learning-limit parameter. NOTE: If you configure this command on an interface in a routed VLAN, and after the MAC addresses learned reaches the limit set in the mac learninglimit command, IP protocols are affected. For example, VRRP sets multiple VRRP Masters and OSPF may not come up.
PAGE 869
Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the S-Series. Version 7.8.1.0 Introduced on the C-Series. Version 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands show mac learning-limit — displays details of the mac learning-limit. mac learning-limit mac-address-sticky Maintain the dynamically learned mac addresses as sticky MAC addresses on the selected port.
PAGE 870
mac learning-limit station-move-violation Specify the actions for a station move violation. S6000 Syntax mac learning-limit station-move-violation {log | shutdown-both | shutdown-offending | shutdown-original} To disable a configuration, use the no mac learning-limit station-moveviolation command, then the configured keyword. Parameters log Enter the keyword log to generate a syslog message on a station move violation.
PAGE 871
mac learning-limit reset Reset the MAC address learning-limit error-disabled state. S6000 Syntax mac learning-limit reset Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 872
static (OPTIONAL) Enter the keyword static to display only those MAC addresses specifically configured on the switch. Optionally, you can also add one of these combinations: address/mac-address, interface/interface, or vlan vlan-id. aging-time Enter the keyword aging-time to display only aging-time information. interface interface (OPTIONAL) Enter the keyword interface then the interface type, slot and port information: • For a Port Channel interface, enter the keywords portchannel then a number.
PAGE 873
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The following describes the show mac-address-table command shown in the following example. Column Heading Description VlanId Displays the VLAN ID number. Mac Address Displays the MAC address in nn:nn:nn:nn:nn:nn format.
PAGE 874
Column Heading Description (Sticky). An (N) indicates that the specified MAC address has been learnt by a neighbor and is synced to the node. Interface State Displays the interface type and slot/port information. The following abbreviations describe the interface types: • gi — Gigabit Ethernet followed by a slot/port • po — Port Channel followed by a number. Range for Terascale is from 1 to 255. \ • so — Sonet followed by a slot/port. • te — 10–Gigabit Ethernet followed by a slot/port.
PAGE 875
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 876
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.
PAGE 877
NOTE: For more information, refer to VLAN Stacking and VLAN-related commands, such as portmode hybrid in the Interfaces chapter. default vlan-id Specify a VLAN as the Default VLAN. S6000 Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1.
PAGE 878
description Add a description about the selected VLAN. S6000 Syntax Parameters description description description Defaults none Command Modes INTERFACE VLAN Command History Related Commands Enter a text string description to identify the VLAN (80 characters maximum). Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 879
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced The no default vlan disable command is not listed in the runningconfiguration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. S6000 Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters vlan-name Enter up to 32 characters as the name of the VLAN.
PAGE 880
show config Display the current configuration of the selected VLAN. S6000 Syntax show config Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 881
• IP address id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094. Only information on the VLAN specified is displayed. name vlanname (OPTIONAL) Enter the keyword name then the name configured for the VLAN. Only information on the VLAN named is displayed. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 882
Column Heading Description NUM Displays existing VLAN IDs. Status Displays the word Inactive for inactive VLANs and the word Active for active VLANs.
PAGE 883
7 Example (VLAN ID) Active T Po20(Gi 13/6) P 100 Active T Po1(Gi 0/1) C 101 I 102 Dell# Inactive T Gi 0/3 Inactive T Gi 0/4 T Gi 13/7 U Gi 13/5 T Gi 0/2 Dell# show vlan id 40 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 40 Status Description Q Ports Active M Gi 13/47 Dell#show vlan id 41 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged,
PAGE 884
Example (OpenFlow instance) Related Commands * O O O NUM 1 3 6 8 12 Status Inactive Inactive Inactive Inactive Inactive Description Q Ports O Te 0/10 vlan-stack compatible — enables the Stackable VLAN feature on the selected VLAN. interface vlan — configures a VLAN. tagged Add a Layer 2 interface to a VLAN as a tagged interface. S6000 Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command.
PAGE 885
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. When you use the no tagged command, the interface is automatically placed in the Default VLAN as an untagged interface unless the interface is a member of another VLAN. If the interface belongs to several VLANs, remove it from all VLANs to change it to an untagged interface.
PAGE 886
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series.
PAGE 887
Defaults All interfaces in Layer 2 mode are untagged. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.
PAGE 888
debug fefd Enable debugging of FEFD. S6000 Syntax debug fefd {events | packets} [interface] To disable debugging of FEFD, use the no debug fefd {events | packets} [interface] command. Parameters events Enter the keyword events to enable debugging of FEFD state changes. packets Enter the keyword packets to enable debugging of FEFD to view information on packets sent and received.
PAGE 889
fefd Enable Far-End Failure Detection on an interface, set the FEFD interval, or select the FEFD mode. S6000 Syntax Parameters fefd {disable|interval|mode {aggressive|normal} disable Enter the keyword disable to disable FEFD for the specified interface. interval Enter the keyword interval, followed by a value to specify the FEFD interval in seconds. Range is from 3 to 300. Default is 15. mode Enter the keyword mode followed by the mode type to specify the FEFD mode.
PAGE 890
Related Commands • • • fefd disable — disables far-end failure detection on an interface. fefd reset — enables FEFD globally on the system. fefd mode — changes FEFD mode on an interface. fefd disable Disable FEFD on an interface only. This command overrides the fefd reset command for the interface. Syntax fefd disable To re-enable FEFD on an interface, use the no fefd disable command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 891
Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 892
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Legacy ESeries command. Related Commands • fefd — enables far-end failure detection.
PAGE 893
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Legacy ESeries command. Related Commands • fefd — enables far-end failure detection. fefd-global interval Configure an interval between FEFD control packets. Syntax fefd-global interval seconds To return to the default value, use the no fefd-global interval command. Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds.
PAGE 894
fefd-global Enable FEFD globally on the system. S6000 Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command. Parameters interval seconds Enter the keyword interval followed by the number of seconds to wait between FEFD control packets. Range is from 3 to 300 seconds. Default is 15 seconds.
PAGE 895
If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. Related Commands • fefd — enables far-end failure detection. • fefd-global interval — configures an interval between FEFD control packets. • show fefd — shows the FEFD command output. show fefd View FEFD status globally or on a specific interface.
PAGE 896
Example Field Description Interface Displays the interfaces type and number. Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets. State Displays the state of the interface and can be one of the following: • bi-directional (interface is up, connected and hearing neighbor’s echoes).
PAGE 897
Link Layer Discovery Protocol (LLDP) 29 The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. This chapter contains the following sections: • LLPD Commands • LLDP-MED Commands LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management.
PAGE 898
vlan-name Enter the keywords vlan-name to advertise the vlan-name TLV. This keyword is only supported on the C-Series and SSeries. Defaults Disabled. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 899
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.
PAGE 900
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface.
PAGE 901
Version 7.4.1.0 Introduced on the E-Series. debug lldp interface To display timer events, neighbor additions or deletions, and other information about incoming and outgoing packets, enable LLDP debugging. S6000 Syntax debug lldp interface {interface | all}{events | packet {brief | detail} {tx | rx | both}} To disable debugging, use the no debug lldp interface {interface | all}{events} {packet {brief | detail} {tx | rx | both}} command.
PAGE 902
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.
PAGE 903
Related Commands Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. hello Configure the rate at which the LLDP control packets are sent to its peer. S6000 Syntax hello seconds To revert to the default, use the no hello seconds command.
PAGE 904
mode To receive or transmit, set LLDP. S6000 Syntax mode {tx | rx} To return to the default, use the no mode {tx | rx} command. Parameters tx Enter the keyword tx to set the mode to transmit. rx Enter the keyword rx to set the mode to receive. Defaults Both transmit and receive. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 905
Parameters integer Enter the number of consecutive misses before the LLDP declares the interface dead. The range is from 2 to 10. Defaults 4 x hello Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 906
Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. S6000 Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface.
PAGE 907
show lldp neighbors Display LLDP neighbor information for all interfaces or a specified interface. S6000 Syntax Parameters show lldp neighbors [interface] [detail] interface detail (OPTIONAL) Enter the following keywords and slot/port or number information: • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information.
PAGE 908
Usage Information Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval. Example R1(conf-if-gi-1/31)#do show lldp neighbors Loc PortID Rem Host Name Rem Port Id Rem Chassis Id -------------------------------------------------------------Gi 1/21 R2 GigabitEthernet 2/11 00:01:e8:06:95:3e Gi 1/31 R3 GigabitEthernet 3/11 00:01:e8:09:c2:4a show lldp statistics Display the LLDP statistical information.
PAGE 909
The E-Series generally supports the commands. However, LLDP-MED commands are more useful on the C-Series and the S50V model of the S-Series, because they support Power over Ethernet (PoE) devices. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information.
PAGE 910
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series. protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 911
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system.
PAGE 912
Usage Information Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 913
Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med softphone-voice To advertise softphone to enable IP telephony on a computer so that the computer can be used as a phone, configure the system.
PAGE 914
Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med streaming-video To advertise streaming video services for broadcast or multicast-based video, configure the system. This command does not include video applications that rely on TCP buffering.
PAGE 915
show lldp neighbors — displays the LLDP neighbors. advertise med video-conferencing To advertise dedicated video conferencing and other similar appliances that support real-time interactive video, configure the system. S6000 Syntax advertise med video-conferencing {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med video-conferencing {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command.
PAGE 916
advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system. S6000 Syntax advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 917
advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system. S6000 Syntax advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 918
advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system. S6000 Syntax advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 919
Microsoft Network Load Balancing 30 This functionality is supported on the S6000 platform. Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
PAGE 920
response with MAC-s4 is received as the last one). The interface associated with server, S4, is added to the ARP table. • With NLB feature enabled, after learning the NLB ARP entry, all the subsequent traffic is flooded on all ports in VLAN1. With NLB, the data frame is forwarded to all the servers for them to perform load-balancing. NLB Multicast Mode Scenario Consider a sample topology in which four servers, namely S1 through S4, are configured as a cluster or a farm.
PAGE 921
learned, traffic is forwarded to only one server rather than the entire cluster, and failover and balancing are not preserved. To preserve failover and balancing, the switch forwards the traffic destined for the server cluster to all member ports in the VLAN connected to the cluster. To ensure that this happens, you must configure the ip vlan-flooding command on the Dell switch at the time that the Microsoft cluster is configured.
PAGE 922
Defaults Not configured. Command Modes CONFIGURATION Command History Version 9.3(0.0) • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • The interface specified here must be one of the interfaces configured using the {output-range | output} interface option with the mac-addresstable static command.
PAGE 923
information inside the ARP packet. This unicast data traffic flooding occurs only for those packets which use these ARP entries.
PAGE 924
Multicast Source Discovery Protocol (MSDP) 31 Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell Networking operating system supports MSDP commands on the S6000 platform.
PAGE 925
clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. S6000 Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 926
clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. S6000 Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 927
ip msdp cache-rejected-sa Enable an MSDP cache for the rejected source-active entries. S6000 Syntax ip msdp cache-rejected-sa {number} To clear the MSDP rejected source-active entries, use the no ip msdp cacherejected-sa {number} command then the ip msdp cache-rejected-sa {number} command. Parameters number Enter the number of rejected SA entries to cache. The range is from 0 to 32766. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 928
Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.) list name Enter the keywords list name and specify a standard access list that contains the RP address that should be treated as the default peer. If no access list is specified, then all SAs from the peer are accepted. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 929
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.1 Introduced ip msdp mesh-group To be a member of a mesh group, configure a peer. S6000 Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command.
PAGE 930
not part of the mesh-group. However, member X cannot forward the SA message to other members of the mesh-group. ip msdp originator-id Configure the MSDP Originator ID. S6000 Syntax ip msdp originator-id {interface} To remove the originator-id, use the no ip msdp originator-id {interface} command. Parameters interface Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 931
Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 6.2.1.1 Introduced ip msdp peer Configure an MSDP peer. S6000 Syntax ip msdp peer peer address [connect-source] [description] [salimit number] To remove the MSDP peer, use the no ip msdp peer peer address [connect-source interface] [description name] [sa-limit number] command. Parameters Defaults peer address Enter the peer address in a dotted decimal format (A.B.C.D.).
PAGE 932
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.
PAGE 933
Parameters list acl-name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 934
access-list name Enter the name of an extended ACL that contains permitted SAs. If you do not use this option, all local entries are blocked. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 935
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the E-Series. Dell Networking OS counts the SA messages originated by itself and those messages received from the MSDP peers. When the total SA messages reach this limit, the subsequent SA messages are dropped (even if they pass RPF checking and policy checking).
PAGE 936
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. S6000 Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 937
sa-cache Enter the keywords sa-cache to display the Source-Active cache. summary Enter the keyword summary to display an MSDP peer summary. Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 938
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. S6000 Syntax show ip msdp sa-cache rejected-sa Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example 938 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 939
32 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s. This command supports the Dell Networking S6000 platform. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol and view information on the protocol.
PAGE 940
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.
PAGE 941
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced. protocol spanning-tree mstp — enters MULTIPLE SPANNING TREE mode. forward-delay The amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State.
PAGE 942
Related Commands Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced. max-age — changes the wait time before MSTP refreshes protocol configuration information. hello-time — changes the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs). S6000 Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 943
max-age — changes the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. S6000 Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 944
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. S6000 Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridge-priority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
PAGE 945
name The name you assign to the multiple spanning tree region. S6000 Syntax name region-name To remove the region name, use the no name command. Parameters region-name Enter the MST region name. The range is 32 character limit. Defaults no default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 946
protocol spanning-tree mstp To enable and configure the multiple spanning tree group, enter MULTIPLE SPANNING TREE mode. S6000 Syntax protocol spanning-tree mstp To disable the multiple spanning tree group, use the no protocol spanningtree mstp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 947
revision The revision number for the multiple spanning tree configuration. S6000 Syntax revision range To return to the default values, use the no revision command. Parameters range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. Defaults 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 948
show config View the current configuration for the mode. Only non-default values are shown. S6000 Syntax show config Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 949
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 950
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and E-Series TeraScale. Version 8.
PAGE 951
BPDU (Mrecords): sent 7, received 1103 The port is not in the portfast mode Example (EDS and LBK) The bold line shows the loopback BPDU inconsistency (LBK_INC). Dell#show spanning-tree msti 0 brief MSTI 0 VLANs mapped 1-4094 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15, max hops 20 Bridge ID Priority 32768, Address 0001.e801.
PAGE 952
Example (Guard) Field Description Instance MSTP instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 953
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface. S6000 Syntax Parameters spanning-tree msti instance {cost cost | priority priority} msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value.
PAGE 954
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. S6000 Syntax tc-flush-standard To disable, use the no tc-flush-standard command.
PAGE 955
can be turned on to enable flushing MAC addresses after receiving every topology change notification.
PAGE 956
33 Multicast The multicast commands are supported by Dell Networking operating system (OS) on all S6000 platform. This chapter contains the following sections: • IPv4 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 957
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands show ip pim tib — shows the PIM tree information base. ip mroute Assign a static mroute.
PAGE 958
distance (OPTIONAL) Enter a number as the distance metric assigned to the mroute. The range is from 0 to 255. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 959
Usage Information Version 7.8.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile. To store multicast routes, use the IN-L3-McastFib CAM partition.
PAGE 960
Related Commands ip pim sparse-mode — enables IGMP and PIM on an interface. show ip mroute View the multicast routing table. S6000 Syntax Parameters show ip mroute [static | group-address [source-address] | count | snooping [vlan vlan-id] [group-address [source-address]] | summary | vlt [group-address [source-address] | count] static (OPTIONAL) Enter the keyword static to view static multicast routes.
PAGE 961
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2. (0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. Version 8.4.1.
PAGE 962
Example (VLT) Dell#show ip mroute vlt IP Multicast Routing Table Flags: S – Synced (*, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Vlan 30 (50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information Example The following describes the show ip mroute command shown in the following example.
PAGE 963
show ip rpf View reverse path forwarding. S6000 Syntax show ip rpf Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 964
Open Shortest Path First (OSPFv2 and OSPFv3) 34 Open Shortest Path First version 2 for IPv4 is supported on S6000 Dell Networking Operating System (OS) platform. Open Shortest Path First version 3 (OSPFv3) for IPv6 is supported on the platform. OSPF is an Interior Gateway Protocol (IGP), which means that it distributes routing information between routers in a single Autonomous System (AS).
PAGE 965
Defaults cost = 1; no areas are configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.
PAGE 966
no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 967
Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 968
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 969
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables.
PAGE 970
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. S6000 Syntax Parameters clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared.
PAGE 971
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. show ip ospf statistics — displays the OSPF statistics. debug ip ospf Display debug information on OSPF.
PAGE 972
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 972 Version 9.4(0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.
PAGE 973
Example Field Description aut: States if OSPF authentication is configured. One of the following is listed: • 0 - no authentication configured • 1 - simple authentication configured using the ip ospf authentication-key command • 2 - MD5 authentication configured using the ip ospf message-digest-key command auk: If the ip ospf authentication-key command is configured, this field displays the key used.
PAGE 974
224.0.0.5 netmask:255.255.255.0 pri:1 N-, MC-, E+, T-, hi:10 di:40 dr:90.1.1.1 bdr:0.0.0.0 default-information originate To generate a default external route into an OSPF routing domain, configure Dell Networking Operating System (OS). S6000 Syntax default-information originate [always] [metric metric-value] [metric-type type-value] [route-map map-name] To return to the default values, use the no default-information originate command.
PAGE 975
Related Commands Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command. S6000 Syntax default-metric number To return to the default values, use the no default-metric [number] command.
PAGE 976
description Add a description about the selected OSPF configuration. S6000 Syntax description description To remove the OSPF description, use the no description command. Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults none Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 977
Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110. ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n format. access-listname (OPTIONAL) Enter the name of an IP standard access list, up to 140 characters. Defaults 110 Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 978
Defaults inter-area dist2 (OPTIONAL) Enter the keywords inter-area then a number to specify a distance metric for routes between areas. The range is from 1 to 255. The default is 110. intra-area dist1 (OPTIONAL) Enter the keywords intra-area then a number to specify a distance metric for all routes within an area. The range is from 1 to 255. The default is 110.
PAGE 979
Parameters prefix-listname Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For Port Channel groups, enter the keywords portchannel then a number. For the C-Series and S-Series, the range is from 1 to 128. • For a SONET interface, enter the keyword sonet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 980
To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters prefix-listname Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed. NOTE: BGP and ISIS routes are not available on the CSeries. BGP, ISIS, and RIP routes are not available on the S-Series. connected (OPTIONAL) Enter the keyword connected to specify that connected routes are distributed.
PAGE 981
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and inter-area routes. fast-convergence This command sets the minimum LSA origination and arrival times to zero (0), allowing more rapid route computation so that convergence takes less time.
PAGE 982
Generally, convergence level 1 meets most convergence requirements. Higher convergence levels should only be selected following consultation with Dell Networking technical support. flood-2328 Enable RFC-2328 flooding behavior. S6000 Syntax flood-2328 To disable, use the no flood-2328 command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 983
graceful-restart grace-period Specifies the time duration, in seconds, that the router’s neighbors continue to advertise the router as fully adjacent regardless of the synchronization state during a graceful restart. NOTE: This command enables OSPFv2 graceful restart globally by setting the grace period (in seconds) that an OSPFv2 router’s neighbors continues to advertise the router as adjacent during a graceful restart.
PAGE 984
graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart. S6000 Syntax graceful-restart helper-reject ip-address To return to default value, use the no graceful-restart helper-reject command. Parameters ip-address Enter the OSPF router-id, in IP address format, of the restart router that will not act as a helper during graceful restart. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 985
To disable graceful restart mode, use the no graceful-restart mode command. Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplannedonly (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only. Defaults Support for both planned and unplanned failures. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 986
Defaults By default, OSPF routers are both helper and restart routers during a graceful restart. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 987
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface.
PAGE 988
pre-Version 6.1.1.1 Usage Information Introduced on the E-Series. All neighboring routers in the same network must use the same password to exchange OSPF information. ip ospf cost Change the cost associated with the OSPF traffic on an interface. S6000 Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters cost Enter a number as the cost. The range is from 1 to 65535. Defaults The default cost is based on the reference bandwidth.
PAGE 989
ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. S6000 Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds.
PAGE 990
Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 991
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 9.1(0.0) Included usage information on maximum number of digest keys per interface. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 992
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.
PAGE 993
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. ip ospf priority To determine the designated router for the OSPF network, set the priority of the interface. S6000 Syntax ip ospf priority number To return to the default setting, use the no ip ospf priority command.
PAGE 994
Use this command for interfaces connected to multi-access networks, not pointto-point networks. ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies belonging to the interface. S6000 Syntax ip ospf retransmit-interval seconds To return to the default values, use the no ip ospf retransmit-interval command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600.
PAGE 995
ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed. S6000 Syntax ip ospf transmit-delay seconds To return to the default value, use the no ip ospf transmit-delay command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 1 second. This value must be greater than the transmission and propagation delays for the interface.
PAGE 996
Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 997
Version 9.0.2.0 Introduced on the S6000. Version 9.1(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series.
PAGE 998
network area Define which interfaces run OSPF and the OSPF area for those interfaces. S6000 Syntax network ip-address mask area area-id To disable an OSPF area, use the no network ip-address mask area areaid command. Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format.
PAGE 999
NOTE: An interface can be attached only to a single OSPF area. If you delete all the network area commands for Area 0, the show ip ospf command output does not list Area 0. passive-interface Suppress both receiving and sending routing updates on an interface. S6000 Syntax passive-interface {default | interface} To enable both the receiving and sending routing, use the no passiveinterface interface command.
PAGE 1000
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Modified to include the keyword default. pre-Version 6.1.1.1 Introduced on the E-Series. Although the passive interface does not send or receive routing updates, the network on that interface is still included in OSPF updates sent using other interfaces.
PAGE 1001
• May update ABR status. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute information from another routing protocol throughout the OSPF process.
PAGE 1002
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF.
PAGE 1003
• 2 = for OSPF External type 2 route-map map-name (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Defaults none Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1004
level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metricvalue (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
PAGE 1005
router-id To configure a fixed router ID, use this command. S6000 Syntax router-id ip-address To remove the fixed router ID, use the no router-id ip-address command. Parameters ip-address Enter the router ID in the IP address format. Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1006
n]: Dell# router ospf To configure an OSPF instance, enter ROUTER OSPF mode. S6000 Syntax router ospf process-id [vrf {vrf name}] To clear an OSPF instance, use the no router ospf process-id command. Parameters process-id Enter a number for the OSPF instance. The range is from 1 to 65535. vrf name (Optional) Enter the VRF process identifier to tie the OSPF instance to the VRF. All network commands under this OSPF instance are then tied to the VRF instance. Defaults Not configured.
PAGE 1007
Example Dell(conf)#router ospf 2 Dell(conf-router_ospf)# show config Display the non-default values in the current OSPF configuration. S6000 Syntax show config Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.
PAGE 1008
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.
PAGE 1009
Line Beginning with Description “Min LSA....” Displays the intervals set for LSA transmission and acceptance. “Number of...” Displays the number and type of areas configured for this process ID. Example Dell#show ip ospf 10 Routing Process ospf 10 with ID 1.1.1.
PAGE 1010
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1011
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf and then the name of the VRF to view LSA information on OSPF processes corresponding to that VRF. databasesummary (OPTIONAL) Enter the keywords database-summary to the display the number of LSA types in each area and the total number of LSAs.
PAGE 1012
Example Field Description Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. Dell>show ip ospf 1 database OSPF Router with ID (11.1.2.1) (Process ID 1) Router (Area 0.0.0.0) Link ID ADV Router Age Seq# Checksum 11.1.2.1 11.1.2.1 673 0x80000005 0x707e 13.1.1.1 13.1.1.1 676 0x80000097 0x1035 192.68.135.2 192.68.135.2 1419 0x80000294 0x9cbd Link ID 10.2.3.2 10.2.4.2 Link ID 0.0.0.0 1.1.1.1 10.1.1.0 10.1.2.0 10.2.2.0 10.2.
PAGE 1013
link-state-id adv-router ipaddress (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ipaddress to display only the LSA information about that router.
PAGE 1014
Field Example Description • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service. • DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. • E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the advertising router’s ID.
PAGE 1015
show ip ospf database external Display information on the AS external (type 5) LSAs. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] database external [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1016
Usage Information Example 1016 Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database external command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router.
PAGE 1017
OSPF Router with ID (20.20.20.5) (Process ID 1) Type-5 AS External LS age: 612 Options: (No TOS-capability, No DC, E) LS type: Type-5 AS External Link State ID: 12.12.12.2 Advertising Router: 20.31.3.1 LS Seq Number: 0x80000007 Checksum: 0x4cde Length: 36 Network Mask: /32 Metrics Type: 2 TOS: 0 Metrics: 25 Forward Address: 0.0.0.0 External Route Tag: 43 LS age: 1868 Options: (No TOS-capability, DC) LS type: Type-5 AS External Link State ID: 24.216.12.0 Advertising Router: 20.20.20.
PAGE 1018
adv-router ipaddress • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ipaddress to display only the LSA information about that router. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1019
Field Description • Example E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Length Displays the Fletcher checksum of an LSA’s complete contents.
PAGE 1020
show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] database nssa-external [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1021
Related Commands Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. show ip ospf database — displays OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] database opaque-area [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process.
PAGE 1022
Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database opaquearea command shown in the following example.
PAGE 1023
Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.1 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000416 Checksum: 0x376 Length: 28 Opaque Type: 1 Opaque ID: 1 Unable to display opaque data LS age: 833 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.2 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000002 Checksum: 0x19c2 --More-Related Commands show ip ospf database — displays OSPF database information.
PAGE 1024
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.
PAGE 1025
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1026
adv-router ipaddress • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router followed by the IP address of an Advertising Router to display only the LSA information about that router. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1027
Item Description • Example E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. LS Seq Number Displays the link state sequence number. This number detects duplicate or old LSAs. Checksum Displays the Fletcher checksum of an LSA’s complete contents. Length Displays the length in bytes of the LSA.
PAGE 1028
Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.142.2 (Link Data) Router Interface address: 192.68.142.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.141.2 (Link Data) Router Interface address: 192.68.141.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.140.
PAGE 1029
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1030
Example Item Description Checksum Displays the Fletcher checksum of an LSA’s complete contents. Length Displays the length in bytes of the LSA. Network Mask Displays the network mask implemented on the area. TOS Displays the TOS options. Option 0 is the only option. Metric Displays the LSA metrics. Dell#show ip ospf 100 database summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Network (Area 0.0.0.
PAGE 1031
show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] interface [interface] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show the OSPF processes that are tied to a specific VRF.
PAGE 1032
Usage Information Example Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id interface command shown in the following example. Item Description GigabitEthernet...
PAGE 1033
Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 192.168.253.1 (Backup Designated Router) GigabitEthernet 13/23 is up, line protocol is up Internet Address 192.168.0.1/24, Area 0.0.0.1 Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DROTHER, Priority 1 Designated Router (ID) 192.168.253.5, Interface address 192.168.0.4 Backup Designated Router (ID) 192.168.253.3, Interface address 192.168.0.
PAGE 1034
Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id neighbor command shown in the following example.
PAGE 1035
Defaults Command Modes Command History none • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.
PAGE 1036
13.0.0.0 150.150.150.0 172.30.1.0 Dell# 1 2 2 0.0.0.0 13.0.0.3 13.0.0.3 Gi 0/47 Gi 0/47 Gi 0/47 0 1 Intra-Area External Intra-Area show ip ospf statistics Display OSPF statistics. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] statistics global | [interface name {neighbor router-id}] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1037
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1038
Row Heading Description Other-Q The queue, for transmission or reception, for the link state acknowledgement, database description, and update packets. The following describes the error definitions for the show ip ospf statistics process-id global command. Example Error Type Description Intf_Down Received packets on an interface that is either down or OSPF is not enabled. Non-Dr Received packets with a destination address of ALL_DRS even though SELF is not a designated router.
PAGE 1039
LSR-Q Other-Q 0 0 0 0 0 0 0 0 Error packets (Only for RX) Intf-Down Wrong-Len Auth-Err Version No-Buffer Q-OverFlow 0 0 0 0 0 0 Non-Dr Invld-Nbr MD5-Err AreaMis Seq-No Unkown-Pkt 0 0 0 0 0 0 Self-Org 0 Nbr-State 0 Chksum 0 Conf-Issues 0 Socket 0 Error packets (Only for TX) Socket Errors Dell# Usage Information Example (Statistics) 0 The show ip ospf process-id statistics command displays the error packet count received on each interface as: • The hello-timer remaining value for each interface
PAGE 1040
show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] timers rate-limit process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view LSAs corresponding to a specific VRF that are currently in queue waiting for timers to expire.
PAGE 1041
show ip ospf topology Display routers in directly connected areas. S6000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] topology process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to information on routers corresponding to a specific VRF that are in directly connected areas.
PAGE 1042
1.1.1.1 Dell# E/-/-/ 1 10.0.0.1 Gi 7/1 1 summary-address To advertise one external route, set the OSPF ASBR. S6000 Syntax summary-address ip-address mask [not-advertise] [tag tag-value] To disable summary address, use the no summary-address ip-address mask command. Parameters ip-address Specify the IP address in dotted decimal format of the address to summarize. mask Specify the mask in dotted decimal format of the address to summarize.
PAGE 1043
Usage Information The area range command summarizes routes for the different areas. With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.0 not-advertise to filter out all the routes fall in range 1.1.0.0/16. Related Commands area range — summarizes routes within an area.
PAGE 1044
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage. timers throttle lsa all Configure LSA transmit intervals. S6000 Syntax timers throttle lsa all {start-interval | hold-interval | maxinterval} To return to the default, use the no timers throttle lsa command.
PAGE 1045
Version 8.3.8.0 Usage Information Introduced on the S4810. LSAs are sent after the start-interval and then after hold-interval until the maximum interval is reached. In throttling, exponential backoff is used when sending same LSA, so that the interval is multiplied until the maximum time is reached. For example, if the start-interval 5000 and hold-interval 1000 and max-interval 100,000, the LSA is sent at 5000 msec, then 1000 msec, then 2000 msec, them 4000 until 100,000 msec is reached.
PAGE 1046
35 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell Networking Operating System (OS). The commands in this chapter are supported on the S6000 platform.
PAGE 1047
Related Commands ip redirect-list – enables an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. S6000 Syntax ip redirect-group redirect-list-name To remove a redirect list from an interface, use the no ip redirect-group name command. Parameters redirect-listname Enter the name of a configured redirect list.
PAGE 1048
• show ip redirect-list – displays the redirect-list configuration. ip redirect-list Configure a redirect list and enter REDIRECT-LIST mode. S6000 Syntax ip redirect-list redirect-list-name To remove a redirect list, use the no ip redirect-list command. Parameters redirect-listname Defaults none Command Modes CONFIGURATION Command History Enter the name of a redirect list. Version 9.4.0.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.2.
PAGE 1049
Parameters ip-protocolnumber Enter a number from 0 to 255 for the protocol identified in the IP protocol header. protocol-type Enter one of the following keywords as the protocol type: icmp for internet control message protocol • ip for any internet protocol • tcp for transmission control protocol • udp for user datagram protocol source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x).
PAGE 1050
Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.5.1.0 Introduced on the E-Series ExaScale. redirect Configure a rule for the redirect list.
PAGE 1051
source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. operator (OPTIONAL) For TCP and UDP parameters only.
PAGE 1052
Parameters sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the IP address of the forwarding router. ip-protocolnumber Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1053
• source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule destinationport Enter the keywords destination-port then the port number to be matched in the ACL rule in the ICAP rule. source-portrange Enter the keywords Source-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
PAGE 1054
Command History Version 9.4. (0.0) Added support for removing SONET interface on the S6000, S4810, S4820T and Z9000 platforms. Version 7.4.1.0 Introduced. Usage Information The show cam pbr command displays the PBR CAM content.
PAGE 1055
Command Modes Command History Example • EXEC • EXEC Privilege Version 9.4. (0.0) Added support for removing SONET interface on the S6000, S4810, S4820T and Z9000 platforms. Dell#show ip redirect-list IP redirect-list ecmp: Defined as: seq 5 redirect 100.1.1.
PAGE 1056
PIM-Sparse Mode (PIM-SM) 36 The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the S6000platform. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement.
PAGE 1057
clear ip pim tib Clear PIM tree information from the PIM database. S6000 Syntax Parameters clear ip pim tib [group] group (OPTIONAL) Enter the multicast group address in dotted decimal format (A.B.C.D). Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1058
To disable PIM debugging, use the no debug ip pim command or use the undebug all to disable all debugging command. Parameters bsr (OPTIONAL) Enter the keyword bsr to view PIM Candidate RP/BSR activities. events (OPTIONAL) Enter the keyword group to view PIM messages for a specific group. group (OPTIONAL) Enter the keyword group to view PIM messages for a specific group. packet [in | out] (OPTIONAL) Enter the keyword packet to view PIM packets.
PAGE 1059
Version 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. S6000 Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1060
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. hash-masklength (OPTIONAL) Enter the hash mask length. The range is from zero (0) to 32. The default is 30. priority (OPTIONAL) Enter the priority used in Bootstrap election process. The range is from zero (0) to 255.
PAGE 1061
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 1062
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. Version 7.7.1.0 Introduced on the E-Series. Example Dell(conf)# ip access-list extended iptv-channels Dell(config-ext-nacl)# permit ip 10.1.2.3/24 225.1.1.
PAGE 1063
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages.
PAGE 1064
ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. S6000 Syntax ip pim register-filter access-list To return to the default, use the no ip pim register-filter access-list command. Parameters access-list Enter the name of an extended access list. Maximum 16 characters. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1065
Parameters address Enter the RP address in dotted decimal format (A.B.C.D). group-address group-address mask Enter the keywords group-address then a group-address mask, in dotted decimal format (/xx), to assign that group address to the RP. override Enter the keyword override to override the BSR updates with static RP. The override takes effect immediately during enable/disable. NOTE: This option is applicable to multicast group range. Defaults Not configured.
PAGE 1066
Parameters interface priority Enter the following keywords and slot/port or number information: • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1067
To disable PIM sparse mode and IGMP, use the no ip pim sparse-mode command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1068
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.
PAGE 1069
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. This command is applicable to last hop routers on the shared tree towards the rendezvous point (RP). show ip pim bsr-router View information on the Bootstrap router. S6000 Syntax show ip pim bsr-router Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1070
show ip pim interface View information on the interfaces with IP PIM enabled. S6000 Syntax show ip pim interface Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1070 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1071
Example Field Description DR Prio Displays the Designated Router priority value configured on the interface (use the ip pim dr-priority command). DR Displays the IP address of the Designated Router for that interface. E600-7-RPM0#show ip pim interface Address Interface Ver/ Nbr Mode Count 172.21.200.254 Gi 7/9 v2/S 0 172.60.1.2 Gi 7/11 v2/S 0 192.3.1.1 Gi 7/16 v2/S 1 192.4.1.1 Gi 13/5 v2/S 0 172.21.110.1 Gi 13/6 v2/S 0 172.21.203.
PAGE 1072
Field Description Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found. Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires). Ver Displays the PIM version number. • DR prio/Mode Example v2 = PIM version 2 Displays the Designated Router priority and the mode.
PAGE 1073
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the S-Series. Example Dell#sh ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.4 224.3.3.3 165.87.20.4 225.1.2.1 165.87.20.4 225.1.2.2 165.87.20.4 229.1.2.1 165.87.20.4 229.1.2.2 165.87.20.
PAGE 1074
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1074 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.
PAGE 1075
Example Field Description Incoming interface Displays the reverse path forwarding (RPF) interface towards the RP/ source. RPF neighbor Displays the next hop from this interface towards the RP/ source.
PAGE 1076
37 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. The commands in this chapter are supported on the S6000 platform. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as Port Channels and virtual local area networks (VLANs). • The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1077
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 1078
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for the rpm/erpm option on the S6000. Version 9.0.2.0 Introduced on the S6000. Version 9.0.2.0 Introduced on the MXL. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1079
Example Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1080
Example Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1081
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1082
• For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. • For a port channel interface, enter the keyword portchannel followed by the port-channel id . range Enter the keyword range to specify the list of interfaces. destination Enter the keyword destination to specify the destination interface. interface direction {rx | tx | both} • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1083
Example Port Monitoring Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1084
Private VLAN (PVLAN) 38 The private VLAN (PVLAN) feature of the Dell Networking operating software is supported on the S6000 platforms. Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell Networking OS private VLAN implementation is based on RFC 3069. For more information, refer to the following commands.
PAGE 1085
Port Types: • Community port: A community port is a port that belongs to a community VLAN and is allowed to communicate with other ports in the same community VLAN and with promiscuous ports. • Isolated port: An isolated port is a port that, in Layer 2, can only communicate with promiscuous ports that are in the same PVLAN. • Promiscuous port: A promiscuous port is a port that is allowed to communicate with any other port type.
PAGE 1086
Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN. show arp — displays the ARP table. switchport mode private-vlan — sets PVLAN mode of the selected port.
PAGE 1087
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. The VLAN: • can be in only one mode, either community, isolated, or primary. • mode ode to community or isolated even before associating it to a primary VLAN. This secondary VLAN continues to work normally as a normal VLAN even though it is not associated to a primary VLAN.
PAGE 1088
Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1089
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1090
Per-VLAN Spanning Tree Plus (PVST+) 39 The Dell Networking operating software implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell Networking OS supports PVST+ on the S6000 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line. description Enter a description of the PVST+. S6000 Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1091
Related Commands protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S6000 Syntax disable To enable PVST+, use the no disable command. Defaults Disabled. Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1092
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S6000 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History This guide is platform-specific.
PAGE 1093
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. S6000 Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 1094
show spanning-tree pvst View the Per-VLAN spanning tree configuration. S6000 Syntax Parameters show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1095
Usage Information Example (Brief) Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. Version 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples. Field Description Interface Name PVST interface. Instance PVST instance.
PAGE 1096
Number of topology changes 3, last change occured 00:57:00 Port 130 (GigabitEthernet 1/0) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.130 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1097
Edge port:no (default) port guard :none (default) Link type: point-to-point (auto) bpdu filter:disable (default) Bpdu guard :disable (default) Bpdus sent 1, received 0 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID --------------------------------------------------------Gi 1/0 128.1223 128 20000 EDS 0 32768 0001.e800.a12b 128.
PAGE 1098
vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. cost number Enter the keyword cost then the port cost value. The range is from 1 to 200000. Defaults: • 100 Mb/s Ethernet interface = 200000. • 1-Gigabit Ethernet interface = 20000. • 10-Gigabit Ethernet interface = 2000. • Port Channel interface with one 100 Mb/s Ethernet = 200000. • Port Channel interface with one 1 Gigabit Ethernet = 20000. • Port Channel interface with one 10 Gigabit Ethernet = 2000.
PAGE 1099
Usage Information Version 8.2.1.0 Introduced the hardware shutdown-on-violation option. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the optional Bridge Port Data Unit (BPDU) guard. Version 6.2.1.1 Introduced. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1100
Related Commands show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. S6000 Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1101
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. S6000 Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1102
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. bridge-priority value Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. Defaults 32768 Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1103
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. forward-delay seconds Enter the keywords forward-delay then the time interval, in seconds, that Dell Networking OS waits before transitioning PVST+ to the forwarding state. The range is from 4 to 30 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1104
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. hello-time seconds Enter the keywords hello-time then the time interval, in seconds, between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. Defaults 2 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1105
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. max-age seconds Enter the keywords max-age then the time interval, in seconds, that Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40 seconds. The default is 20 seconds. Defaults 20 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1106
40 Quality of Service (QoS) The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking Products.S6000 platform. This chapter contains the following sections: • Global Configuration Commands • Per-Port QoS Commands • Policy-Based QoS Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1107
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced. service-class bandwidth-percentage Specify a minimum bandwidth for queues. S6000 Syntax service-class bandwidth-percentage queue0 number queue1 number queue2 number queue3 number queue4 number queue5 number queue6 number queue7 number service-class bandwidth-percentage queue0 number queue1 number queue2 number queue3 number Parameters number Enter the bandwidth-weight, as a percentage.
PAGE 1108
service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. S6000 Syntax Parameters Defaults service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} queue Enter a value from 0 to 7. For each dot1p Priority, the default CoS queue value is: • Dot1p Priority : 0 1 2 3 4 5 6 7 • Queue : 2 0 1 3 4 5 6 7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1109
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. service-class dot1p-mapping — Identifies the class map.
PAGE 1110
line rate traffic over the SP queue, it starves all other queues on the ports on which this traffic is flowing. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives. S6000 Syntax dot1p-priority priority-value To delete the IEEE 802.1p configuration on the interface, use the no dot1ppriority command.
PAGE 1111
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The dot1p-priority command changes the priority of incoming traffic on the interface. The system places traffic marked with a priority in the correct queue and processes that traffic according to its queue.
PAGE 1112
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage Information NOTE: Per Port rate shape and rate police is supported for Layer 2 tagged and untagged switched traffic and for Layer 3 traffic. Per VLAN rate shape and rate police is supported on only tagged ports with Layer 2 switched traffic.
PAGE 1113
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. On 40-port 10G stack-unit if the traffic is shaped between 64 and 1000 Kbs, for some values, the shaped rate is much less than the value configured. NOTE: When packets of size greater than 7000 bytes are expected to be received from the network, Dell Networking recommends that you configure the burst value to be more than 175 KB if you configured the rate shape.
PAGE 1114
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. To honor all incoming 802.1p markings on incoming switched traffic on the interface, enter this command. By default, this facility is not enabled (that is, the 802.1p markings on incoming traffic are not honored).
PAGE 1115
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.1.9.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.1 Introduced on the E-Series.
PAGE 1116
no Negate a command or set its defaults show Show buffer-stats-snapshot configuration Dell(conf-buffer-stats-snapshot)#no disable Dell(conf-buffer-stats-snapshot)#show configuration ! buffer-stats-snapshot no disable class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-ofservice policies to each class.
PAGE 1117
Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Class-map names can be 32 characters. Layer2 available on the C-Series and S-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 E-Series Only: Expanded to add support for Layer 2. Usage Information Packets arriving at the input interface are checked against the match criteria and configured using this command to determine if the packet belongs to that class.
PAGE 1118
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.18.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1119
Related Commands Version 8.3.7.0 Introduced on the S4810. pre-Version 7.7.1.0 Introduced. policy-map-input — creates an input policy map. policy-map-output — creates an output policy map. qos-policy-input — creates an input QoS-policy on the router. qos-policy-output — creates an output QoS-policy on the router. wred-profile — creates a WRED profile. match ip access-group Configure match criteria for a class map, based on the access control list (ACL).
PAGE 1120
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed.
PAGE 1121
Usage Information Version 9.5(0.0) Added the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive.
PAGE 1122
set-ip-dscp value (OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63. Defaults none Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1123
Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1124
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands class-map — identifies the class map. match mac vlan Configure a match criterion for a class map based on VLAN ID. S6000 Syntax Parameters match mac vlan number number Enter the VLAN ID. The range is from 1 to 4094. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific.
PAGE 1125
Parameters qos-policyname Enter the name of the policy map in character format (32 characters maximum). Defaults none Command Modes CONFIGURATION (policy-map-input and policy-map-output) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1126
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1127
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1128
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined. This command enables the qos-policyinput configuration mode— (conf-qos-policy-in).
PAGE 1129
Version 8.3.7.0 Introduced on the S4810. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rate-shape, scheduler strict, bandwidth-percentage, and WRED can be defined. This command enables the qos-policy-output configuration mode —(conf-qos-policy-out). Related Commands bandwidth-percentage — assigns percentage of bandwidth to the class/queue. wred — assigns yellow or green drop precedence.
PAGE 1130
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage Information The default burst size is 100Kb. If a different value is required, you must configure the burst size to the required value. Related Commands rate police — specifies traffic policing on the selected interface. qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy.
PAGE 1131
qos-policy-output — creates a QoS output policy. service-policy input Apply an input policy map to the selected interface. S6000 Syntax service-policy input policy-map-name [layer2] To remove the input policy map from the interface, use the no service-policy input policy-map-name [layer2] command. Parameters policy-mapname Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist.
PAGE 1132
service-policy output Apply an output policy map to the selected interface. S6000 Syntax service-policy output policy-map-name To remove the output policy map from the interface, use the no servicepolicy output policy-map-name command. Parameters policy-mapname Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist.
PAGE 1133
Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7. class-map class-mapname (OPTIONAL) Enter the keyword class-map then the class map name assigned to the queue in character format (32 character maximum). NOTE: This option is available under policy-mapinput only. qos-policy qos-policyname (OPTIONAL) Enter the keywords qos-policy then the QoS policy name assigned to the queue in text format (32 characters maximum).
PAGE 1134
Parameters ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63. mac-dot1p value Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7. Defaults none Command Modes CONFIGURATION (conf-qos-policy-in) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1135
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Dell#show qos class-map Class-map match-any CM Match ip access-group ACL Related Commands class-map — identifies the class map. show qos policy-map View the QoS policy map information.
PAGE 1136
Example (IPv4) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1137
Parameters policy-mapname Enter the policy map name. class classmap-name Enter the keyword class then the class map name. qos-policyinput qospolicy-name Enter the keyword qos-policy-input then the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1138
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1139
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Dell#show qos qos-policy-input Qos-policy-input QosInput Rate-police 100 50 peak 100 50 Dscp 32 Dell# show qos qos-policy-output View the output QoS policy details. S6000 Syntax Parameters show qos qos-policy-output [qos-policy-name] qos-policyname Enter the QoS policy name.
PAGE 1140
show qos statistics View QoS statistics. S6000 Syntax Parameters show qos statistics {wred-profile [interface]} | [interface] wred-profile interface interface Enter the keywords wred-profile and optionally one of the following keywords and slot/port or number information: • For a 40–Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1141
Parameters wred-profilename Enter the WRED profile name to view the profile details. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1142
sharedthresholdweight Specify the weight of a queue for the shared buffer space queue 0 to queue 7 Specify the queue number to which the WRED parameters apply number Enter a weight for the queue on the shared buffer as a number in the range of 1 to 11. Default The default threshold weight on the shared buffer for each queue is 9. Therefore, each queue can consume up to 66.67 percent of available shared buffer by default.
PAGE 1143
Example Dell(conf-if-te-0/8)#Service-class buffer shared-thresholdweight queue5 4 queue7 6 test cam-usage Check the Input Policy Map configuration for the CAM usage. S6000 Syntax Parameters test cam-usage service-policy input policy-map stack-unit {[number port-set portpipe number] | [all]} policy-map Enter the policy map name. stackunitnumber (OPTIONAL) Enter the keyword stack-unit then the stackunit slot number.
PAGE 1144
Field Description stack-unit Indicates the stack-unit slot number. Portpipe Indicates the portpipe number. CAM Partition The CAM space where the rules are added. Available CAM Indicates the free CAM space, in the partition, for the classification rules. NOTE: The CAM entries reserved for the default rules are not included in the Available CAM column; free entries, from the default rules space, cannot be used as a policy map for the classification rules.
PAGE 1145
Allowed (2) Dell# threshold Specify the minimum and maximum threshold values for the configured WRED profiles. S6000 Syntax threshold min number max number max-drop-probability To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360. min number Enter the keyword min then the minimum threshold number for the WRED profile.
PAGE 1146
Related Commands Pre-Defined WRED Profile Name Minimum Threshold Maximum Threshold Maximum Drop Rate wred_drop 0 0 100 wred_teng_y 594 5941 100 wred_teng_g 594 5941 50 wred_fortyg_y 594 5941 50 wred_fortyg_g 594 5941 25 wred-profile — creates a WRED profile. trust Specify dynamic classification (DSCP) or dot1p to trust. S6000 Syntax Parameters trust {diffserv [fallback]| dot1p [fallback]} diffserv Enter the keyword diffserv to specify trust of DSCP markings.
PAGE 1147
Dynamic mapping honors packets marked according to the standard definitions of DSCP. The following lists the default mapping.
PAGE 1148
Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_. Defaults When WRED green is applied, default WRED yellow profiles take effect and viceversa. Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 1149
Usage Information Version 8.3.19.0 Introduced on the S4820t. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. When you enable wred ecn, and the number of packets in the queue is below the minimum threshold, packets are transmitted per the usual WRED treatment.
PAGE 1150
Command History Version 9.3.0.0 Introduced on the S6000 and Z9000 platforms Usage Information If the average queue size is more than the maximum threshold of WRED, the packet is dropped. If the average queue size is between the minimum and maximum threshold values, the decision to drop or queue the packet is taken based on the packet drop probability. The probability that a packet is dropped depends on the minimum threshold, maximum threshold, and mark probability denominator.
PAGE 1151
Version 8.3.7.0 Introduced on the S4810. Usage Information Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred). Related Commands threshold — specifies the minimum and maximum threshold values of the WRED profile.
PAGE 1152
kbps Enter the keyword kbps to specify the peak rate limit in Kilobits per second (Kbps). Specify this value as a multiple of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps). pps Enter the keyword pps to specify the peak rate limit in packets per second (pps). The range is from 1 to 268000000. The default granularity is Megabits per second (Mbps). peak-rate Define the peak rate, which is the guaranteed or minimum confirmed rate for the packets.
PAGE 1153
Example Dell (conf-qos-policy-out) #rate-shape pps 100 100 peak pps 1000 200 Dell (conf-qos-policy-out) #rate-shape kbps 1024 100 peak kbps 102400 75 Dell (conf-qos-policy-out) # rate-shape 100 100 peak 1000 750 Dell(conf-qos-policy-in)#rate-police 100 25 peak 80 500 % Error: Peak rate cannot be less than committed rate.
PAGE 1154
Command Modes Command History Usage Information CONFIGURATION mode Version 9.3.0.0 Introduced on the S6000 and Z9000 platforms You can configure only service pools 0 and 1 because the Dell Networking OS uses only these two service pools. The pool, service0, is used for lossy queues and the pool, service1, is used for lossless (PFC) queues in all the platforms.
PAGE 1155
Default By default, ECN marking is disabled on all queues. Command Modes CONFIGURATION mode Command History Usage Information Example Version 9.3.0.0 Introduced on the S6000 and Z9000 platforms You can add or remove ECN marking configuration on a list of queues on all backplane ports. All of the configured attributes apply to all the backplane ports and are for each queue. You can configure all the data queues. For Z9000, you can configure queues 0-3.
PAGE 1156
Parameters Yellow Enter the yellow keyword. Traffic marked as yellow delivers traffic to the egress queue which either transmits the packet if it has available bandwidth or drops the packet due to no ability to send. Red Enter the red keyword. Traffic marked as red is dropped. dscp-list Enter a list of IP DSCP values. The dscp-list parameter specifies the full list of IP DSCP value(s) for the specified color.
PAGE 1157
qos dscp-color-map Configure the DSCP color map. Syntax qos dscp-color-map map-name To remove a color map, use the no qos dscp-color-map map-name command. Parameters map-name Enter the name of the DSCP color map. The map name can have a maximum of 32 characters. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1158
Parameters color-mapprofile-name Enter the color map profile name. The name can have a maximum of 32 characters. Defaults None Command Modes CONFIG-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL.
PAGE 1159
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.5.0.0 Example Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display summary information about a color policy on one or more interfaces.
PAGE 1160
The following is a list of the Dell Networking OS version history for this command. Version 9.5.0.0 Example Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps. Dell# show qos dscp-color-map Dscp-color-map mapONE yellow 4,7 red 20,30 Dscp-color-map mapTWO yellow 16,55 Display a specific DSCP color map.
PAGE 1161
Routing Information Protocol (RIP) 41 Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking operating software supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2) on the S6000 platform. The Dell Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, refer to the Dell Networking OS Configuration Guide.
PAGE 1162
clear ip rip Update all the RIP routes in the Dell Networking OS routing table. S6000 Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 1163
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. database (OPTIONAL) Enter the keyword database to display messages when there is a change to the RIP database.
PAGE 1164
To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to enable the switch software to always advertise the default route. metric metricvalue (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 1 to 16. The default is 1. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of a configured route-map. Defaults Disabled. Metric: 1.
PAGE 1165
Parameters number Specify a number. The range is from 1 to 16. The default is 1. Defaults 1 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 1166
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1167
Defaults weight = 120 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1168
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 1169
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1170
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. S6000 Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1171
2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1172
Defaults RIPv1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1173
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. ip poison-reverse — sets the prefix for RIP routing updates. maximum-paths Set RIP to forward packets over multiple paths.
PAGE 1174
Usage Information Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. S6000 Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command. Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured.
PAGE 1175
To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. Related Commands passive-interface — sets the interface to only listen to RIP broadcasts. network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command. S6000 Syntax network ip-address To disable RIP for a network, use the no network ip-address command.
PAGE 1176
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. S6000 Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters prefix-listname Enter the name of an established Prefix list to determine which incoming routes are modified.
PAGE 1177
Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information When the offset metric is applied to an interface, that value takes precedence over an offset value that is not extended to an interface. Related Commands ip prefix-list — enters PREFIX-LIST mode and configure a prefix list. output-delay Set the interpacket delay of successive packets to the same neighbor.
PAGE 1178
Usage Information This command is intended for low-speed interfaces. passive-interface Suppress routing updates on a specified interface. S6000 Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. Parameters interface Enter the following information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 1179
Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information Although the passive interface does not send or receive routing updates, the network on that interface still includes in RIP updates sent using other interfaces. Related Commands neighbor — enables RIP for a specified network. network — defines a neighbor. redistribute Redistribute information from other routing instances.
PAGE 1180
pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command. Related Commands default-information originate — generates a default route for RIP traffic. redistribute isis Redistribute routing information from an IS-IS instance.
PAGE 1181
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. pre-Version 6.2.1.1 Introduced on the E-Series. redistribute ospf Redistribute routing information from an OSPF process.
PAGE 1182
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. router rip To configure and enable RIP, enter ROUTER RIP mode. S6000 Syntax router rip To disable RIP, use the no router rip command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1183
Related Commands network — enables RIP. exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration. The default values are not shown. S6000 Syntax show config Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 1184
show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. S6000 Syntax Parameters show ip rip database [ip-address mask] ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If you enter an IP address, also enter a mask for that IP address. mask (OPTIONAL) Specify a mask, in /network format, for the IP address.
PAGE 1185
Example Dell#show ip rip database Total number of routes in RIP database: 1624 204.250.54.0/24 [50/1] via 192.14.1.3, 00:00:12, GigabitEthernet 9/15 204.250.54.0/24 auto-summary 203.250.49.0/24 [50/1] via 192.13.1.3, 00:00:12, GigabitEthernet 9/14 203.250.49.0/24 auto-summary 210.250.40.0/24 [50/2] via 1.1.18.2, 00:00:14, Vlan 18 [50/2] via 1.1.130.2, 00:00:12, Port-channel 30 210.250.40.0/24 auto-summary 207.250.53.0/24 [50/2] via 1.1.120.2, 00:00:55, Port-channel 20 [50/2] via 1.1.130.
PAGE 1186
Example show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.0.0 passive-interface GigabitEthernet 2/0 neighbor 20.20.20.20 redistribute ospf 999 version 2 timers basic Manipulate the RIP timers for routing updates, invalid, holddown times, and flush time. S6000 Syntax timers basic update invalid holddown flush To return to the default settings, use the no timers basic command.
PAGE 1187
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1188
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. ip rip receive version — sets the RIP version the interface receives. ip rip send version — sets the RIP version the interface sends.
PAGE 1189
Remote Monitoring (RMON) 42 The Dell Networking operating software remote monitoring (RMON) is implemented on the S6000 platform. Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1190
variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table.
PAGE 1191
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on an interface. S6000 Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command.
PAGE 1192
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection statistics Enable RMON MIB statistics collection on an interface. S6000 Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command.
PAGE 1193
Version 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table. S6000 Syntax rmon event number [log] [trap community] [description string] [owner name] To disable RMON on an interface, use the no rmon event number [log] [trap community] [description string] command. Parameters number Assign an event number in integer format from 1 to 65535. The number value must be unique in the RMON event table. log (OPTIONAL) Enter the keyword log to generate an RMON log entry.
PAGE 1194
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon hc-alarm Set an alarm on any MIB object. S6000 Syntax rmon hc-alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] To disable the alarm, use the no rmon hc-alarm number command. Parameters 1194 number Enter the alarm integer number from 1 to 65535.
PAGE 1195
If there is no corresponding falling-threshold event, the value is zero. owner string (OPTIONAL) Enter the keyword owner then the owner name to specify an owner for the alarm. This is the alarmOwner object in the alarmTable of the RMON MIB. Defaults owner Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1196
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Dell# show rmon RMON status total memory used 218840 bytes.
PAGE 1197
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon alarm 1 RMON alarm entry 1 sample Interval: 5 object: 1.3.6.1.2.1.1.3 sample type: absolute value. value: 255161 alarm type: rising or falling alarm.
PAGE 1198
show rmon events Display the contents of the RMON event table. S6000 Syntax Parameters show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1199
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Dell# 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. S6000 Syntax Parameters show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1200
Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon hc-alarm 1 RMON high-capacity alarm entry 1 object: 1.3.6.1.2.1.1.3 sample interval: 5 sample type: absolute value. value: 185638 alarm type: rising or falling alarm. alarm rising threshold value: positive. rising threshold: 1001, RMON event index: 1 alarm falling threshold value: positive. falling threshold: 999, RMON event index: 6 alarm sampling failed 0 times. alarm owner: 1 alarm storage type: non-volatile.
PAGE 1201
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1202
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1203
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example (Index) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1204
HC 1024-1518 bytes packets overflow: 0 HC 1024-1518 bytes packets: 0 Dell# Example (Brief) 1204 Dell#show rmon statistics br index ifIndex interface ---------------------------------------6001 100974631 TenGigabitEthernet 2/0 6002 100974631 TenGigabitEthernet 2/0 6003 101236775 TenGigabitEthernet 2/1 6004 101236775 TenGigabitEthernet 2/1 9001 134529054 TenGigabitEthernet 3/0 9002 134529054 TenGigabitEthernet 3/0 9003 134791198 TenGigabitEthernet 3/1 9004 134791198 TenGigabitEthernet 3/1 Dell# Remote Moni
PAGE 1205
Rapid Spanning Tree Protocol (RSTP) 43 The Dell Networking operating software implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking OS supports RSTP on the S6000 platform. bridge-priority Set the bridge priority for RSTP.
PAGE 1206
Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. S6000 Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disable debugging, use the no debug spanning-tree rstp command. Parameters all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu interface {in | out} (OPTIONAL) Enter the keyword bpdu to debug the bridge protocol data units.
PAGE 1207
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.1 Introduced on the E-Series.
PAGE 1208
Related Commands Version 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. S6000 Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific.
PAGE 1209
forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. S6000 Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds that FTOS waits before transitioning RSTP to the forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1210
hello-time Set the time interval between the generation of the RSTP bridge protocol data units (BPDUs). S6000 Syntax hello-time [milli-second] seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. milli-second Enter the keywords milli-second to configure a hello time on the order of milliseconds.
PAGE 1211
Related Commands forward-delay — changes the wait time before RSTP transitions to the Forwarding state. max-age — changes the wait time before RSTP refreshes the protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the RSTP bridge. S6000 Syntax max-age seconds To return to the default values, use the no max-age command.
PAGE 1212
hello-time — changes the time interval between BPDUs. protocol spanning-tree rstp To configure RSTP, enter RSTP mode. S6000 Syntax protocol spanning-tree rstp To exit RSTP mode, use the exit command. Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1213
show config View the current configuration for the mode. Only non-default values are displayed. S6000 Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1214
Command Modes Command History Usage Information Example (Brief) • EXEC • EXEC Privilege Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Added support for the optional guard keyword on the CSeries, S-Series, and E-Series TeraScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.
PAGE 1215
Gi 4/9 Altr 128.427 128 20000 BLK 20000 P2P Dell# Example (EDS, LBK) No NOTE: “LBK_INC” (bold) means Loopback BPDU Inconsistency. Dell#show spanning-tree rstp br Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e801.
PAGE 1216
spanning-tree rstp Configure an RSTP interface with one of these settings: port cost, edge port with optional bridge port data unit (BPDU) guard, port priority, loop guard, or root guard. S6000 Syntax Parameters spanning-tree rstp {cost port-cost | edge-port [bpduguard [shutdown-on-violation]] | priority priority | {loopguard | rootguard}} cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1217
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.
PAGE 1218
• Example If no BPDU is received from a remote device, loop guard places the port in a Loop-Inconsistent Blocking state and no traffic is forwarded on the port. Dell(conf)#interface gigabitethernet 4/0 Dell(conf-if-gi-4/0)#spanning-tree rstp edge-port Dell(conf-if-gi-4/0)#show config ! interface GigabitEthernet 4/0 no ip address switchport spanning-tree rstp edge-port no shutdown Dell# tc-flush-standard Enable the MAC address flushing after receiving every topology change notification.
PAGE 1219
knob command to enable flushing MAC addresses after receiving every topology change notification.
PAGE 1220
44 Security Most of the commands in this chapter are available on the S6000 platform. This chapter contains various types of security commands offered in the Dell Networking operating software. The commands are listed in the following sections: • AAA Accounting Commands • Authorization and Privilege Commands • Authentication and Password Commands • RADIUS Commands • TACACS+ Commands • Port Authentication (802.
PAGE 1221
Parameters system Enter the keyword system to send accounting information of any other AAA configuration. exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. commands {level | role role-name Enter the keyword command then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role.
PAGE 1222
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. In the example above, TACACS+ accounting is used to track all usage of EXEC command and commands on privilege level 15. Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
PAGE 1223
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. Dell Networking OS issues accounting records for all users on the system, including users whose username string, due to protocol translation, is NULL. For example, a user who comes on line with the aaa authentication login method-list none command is applied.
PAGE 1224
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting.
PAGE 1225
interface tengigabitethernet 0/36 Dell(conf)#exit Dell(conf)#aaa radius group group1 show accounting Display the active accounting sessions for each online user. S6000 Syntax show accounting Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 1226
Authorization and Privilege Commands To set command line authorization and privilege levels, use the following commands. authorization Apply an authorization method list to terminal lines. S6000 Syntax Parameters authorization {exec | commands {level | role role-name}} method-list exec Enter the keyword exec to apply an EXEC level authorization method list.
PAGE 1227
Related Commands aaa authorization commands — sets the parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands aaa authorization exec — sets the parameters that restrict (or permit) a user’s access to EXEC level commands. aaa authorization commands Set parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands.
PAGE 1228
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Added support for RADIUS. aaa authorization config-commands Set parameters that restrict (or permit) a user’s access to EXEC level commands. S6000 Syntax aaa authorization config-commands Disable authorization checking for CONFIGURATION level commands using the no aaa authorization config-commands command.
PAGE 1229
aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands. S6000 Syntax aaa authorization exec {name | default} {local || tacacs+ || if-authenticated || none} To disable authorization checking for EXEC level commands, use the no aaa authorization exec command. Parameters name Define a name for the list of authorization methods. default Define the default list of authorization methods.
PAGE 1230
To delete access to a level and command, use the no privilege mode level level command command. Parameters mode level level Enter one of the following keywords as the mode for which you are controlling access: • configure for CONFIGURATION mode • exec for EXEC mode • interface for INTERFACE modes • line for LINE mode • route-map for ROUTE-MAP mode • router for ROUTER OSPF, ROUTER RIP, ROUTER ISIS and ROUTER BGP modes Enter the keyword level then a number for the access level.
PAGE 1231
Usage Information To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines. S6000 Syntax privilege level level To delete access to a terminal line, use the no privilege level level command. Parameters level level Enter the keyword level then a number for the access level. The range is from 0 to 15.
PAGE 1232
aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). S6000 Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | method-list-name} method [... method2] command. Parameters default Enter the keyword default then the authentication methods to use as the default sequence of methods for the Enable login.
PAGE 1233
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell Networking OS uses the methods defined for Enable access instead. Methods configured with the aaa authentication enable command are evaluated in the order they are configured.
PAGE 1234
• • • local: use the password for the userid contained in the local password database. • none: no authentication. Not available if role-only is in use. radius: use the RADIUS servers configured with the radius-server host command. tacacs+: use the TACACS+ servers configured with the tacacs-server host command. • • ... method4 enable: use the password the enable password command defines in CONFIGURATION mode. Not available if role-only is in use.
PAGE 1235
method listed, Dell Networking OS applies the next method configured. If users fail the first method listed, no other methods are applied. The only exception is the local method. If the user’s name is not listed in the local database, the next method is applied. If the correct user name/password combination is not entered, the user is not allowed access to the switch.
PAGE 1236
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. line — applies an authentication method list to the designated terminal lines. ip access-list standard — names (or selects) a standard access list to filter based on the IP address.
PAGE 1237
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1238
Parameters encryptiontype (OPTIONAL) Enter the number 7 as the encryption type. Enter 7 followed a text string as the hidden password. The text string must be a password that was already encrypted by a Dell Networking router. Use this parameter only with a password that you copied from the show running-config file of another Dell Networking router. password Enter a text string, up to 32 characters long, as the clear text password. Defaults Not configured.
PAGE 1239
encryptiontype (OPTIONAL) Enter the number 5 or 0 as the encryption type. Enter a 5 then a text string as the hidden password. The text string must be a password that was already encrypted by a Dell Networking router. Use this parameter only with a password that you copied from the show running-config file of another Dell Networking router. password Enter a text string, up to 32 characters long, as the clear text password. Defaults No password is configured. level = 15.
PAGE 1240
Related Commands show running-config — views the current configuration. privilege level (CONFIGURATION mode) — controls access to the command modes within the switch. login authentication To designate the terminal lines, apply an authentication method list. S6000 Syntax login authentication {method-list-name | default} To use the local user/password database for login authentication, use the no login authentication command.
PAGE 1241
Related Commands aaa authentication login — selects the login authentication methods. password Specify a password for users on terminal lines. S6000 Syntax password [encryption-type] password To delete a password, use the no password password command. Parameters encryptiontype password (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the password entered. The options are • 0 is the default and means the password is not encrypted and stored as clear text.
PAGE 1242
Related Commands enable password — sets the password for the enable command. login authentication — configures an authentication method to log in to the switch. service password-encryption — encrypts all passwords configured in Dell Networking OS . radius-server key — configures a key for all RADIUS communications between the switch and the RADIUS host server. tacacs-server key — configures a key for communication between a TACACS+ server and client.
PAGE 1243
lower number (OPTIONAL) Enter the keyword lower then the lower number. The range is from 0 to 31. numeric number (OPTIONAL) Enter the keyword numeric then the numeric number. The range is from 0 to 31. special-char number (OPTIONAL) Enter the keywords special-char then the number of special characters permitted. The range is from 0 to 31. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1244
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1245
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Example Dell#show privilege Current privilege level is 15 Dell# Related Commands privilege level (CONFIGURATION mode) — assigns access control to different command modes.
PAGE 1246
Usage Information Example Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lines currently in use. User Displays the user name of all users logged in. Host(s) Displays the terminal line status.
PAGE 1247
• AUX: the range is from 1 to 300 seconds, the default is 0 seconds (no timeout). Defaults See the defaults settings shown in Parameters. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1248
nopassword Enter the keyword nopassword to specify that the user should not enter a password. password Enter the keyword password then the encryption-type or the password. secret Enter the keyword secret then the encryption-type or the password. encryptiontype Enter an encryption type for the password that you enter. • 0 directs the system to store the password as clear text. It is the default encryption type when using the password option.
PAGE 1249
Version 7.7.1.0 Added support for the secret option and the MD5 password encryption. Extended the name from 25 to 63 characters. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information To view the defined user names, use the show running-config user command. Related Commands password — specifies a password for users on terminal lines. show running-config — views the current configuration.
PAGE 1250
Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections. S6000 Syntax ip radius source-interface interface To delete a source interface, use the no ip radius source-interface command.
PAGE 1251
Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped.
PAGE 1252
radius-server group Creates or deletes a group of radius servers. Syntax Parameters radius-server group group-name group-name Enter the group name that denotes the group of RADIUS servers. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.
PAGE 1253
radius-server host Configure a RADIUS server host. S6000 Syntax Parameters radius-server host {hostname | ipv4-address | ipv6-address} [auth-port port-number] [retransmit retries] [timeout seconds] [key [encryption-type] key] hostname Enter the name of the RADIUS server host. ipv4-address | ipv6-address Enter the IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the RADIUS server host. auth-port portnumber (OPTIONAL) Enter the keywords auth-port then a number as the port number.
PAGE 1254
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.0 Added support for IPv6. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 1255
Related Commands login authentication — sets the database to be checked when a user logs in. radius-server key — sets an authentication key for RADIUS communications. radius-server retransmit — sets the number of times the RADIUS server attempts to send information. radius-server timeout — sets the time interval before the RADIUS server times out. radius-server vrf Create an association between a RADIUS server group and a VRF and source interface..
PAGE 1256
The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Usage Information Introduced on the S-Series and Z-Series. You can use this command to associate a group of RADIUS servers with a VRF and source interface. You can configure the source interface only with the VRF attribute and source interface is optional with the VRF attributes. If VRF is not configured on the RADIUS group, then the group is considered to be on the default VRF.
PAGE 1257
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 1258
Defaults 3 retries Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1259
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. radius-server host — configures a RADIUS host. TACACS+ Commands Dell Networking OS supports TACACS+ as an alternate method for login authentication.
PAGE 1260
Example Dell(conf)#tacacs-server group group1 Dell(conf-tacacs-group)#tacacs-server host 1.1.1.1 key secret Dell(conf-tacacs-group)#tacacs-server host 2.2.2.2 key secret Dell(conf-tacacs-group)#tacacs-server vrf vrf1 sourceinterface tengigabitethernet 0/36 Dell(conf)#exit Dell(conf)#aaa tacacsgroup group1 Related Commands aaa authentication login — specifies the login authentication method. tacacs-server key — configures a TACACS+ key for the TACACS server.
PAGE 1261
ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections. S6000 Syntax ip tacacs source-interface interface To delete a source interface, use the no ip tacacs source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1262
Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. tacacs-server group Creates a group of TACACS servers. Syntax tacacs-server group group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command. Parameters group-name Enter the name of the TACACS server group. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1263
tacacs-server host Specify a TACACS+ host. S6000 Syntax Parameters tacacs-server host {hostname | ipv4-address | ipv6-address} [port number] [timeout seconds] [key key] hostname Enter the name of the TACACS+ server host. ipv4-address | ipv6-address Enter the IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the TACACS+ server host. port number (OPTIONAL) Enter the keyword port then a number as the port to be used by the TACACS+ server. The range is from zero (0) to 65535. The default is 49.
PAGE 1264
pre-Version 6.2.1.1 Usage Information Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times. If you are not configuring the switch as a TACACS+ server, you do not need to configure the port, timeout and key optional parameters. If you do not configure a key, the key assigned in the tacacs-server key command is used. You can use duplicate host names or IP addresses among TACACS groups.
PAGE 1265
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1266
• For the Null interface, enter the keywords null 0. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 1267
port to which a client is connected. After authentication is successful, normal traffic passes through the port. Dell Networking OS supports RADIUS and Active Directory environments using 802.1X Port Authentication. Important Points to Remember Dell Networking OS limits network access for certain users by using VLAN assignments. 802.1X with VLAN assignment has these characteristics when configured on the switch and the RADIUS server. • 802.1X is supported on S6000. • 802.
PAGE 1268
Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series. dot1x authentication (Interface) — enables dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface; dot1x must be enabled both globally and at the interface level.
PAGE 1269
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts then number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 1270
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1271
Usage Information 802.1X authentication is enabled when an interface is connected to the switch. If the host fails to respond within a designated amount of time, the authenticator places the port in the guest VLAN. If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable. Therefore, a guest VLAN is allocated to the interface and authentication for the device occurs at the next re-authentication interval (dot1x reauthentication).
PAGE 1272
Version 8.4.1.0 Usage Information Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-authbypass command. dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. S6000 Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command.
PAGE 1273
Parameters forceauthorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly deauthorize a port. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1274
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.
PAGE 1275
Version 7.4.1.0 Related Commands Introduced on the E-Series. interface range — configures a range of interfaces. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. S6000 Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2.
PAGE 1276
Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1277
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs are transmitted by the Authenticator PAE. S6000 Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command.
PAGE 1278
show dot1x interface Display the 802.1X information on an interface. S6000 Syntax Parameters show dot1x interface interface interface Enter one of the following keywords and slot/port or number information: • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information.
PAGE 1279
Auth-Fail VLAN id: Auth-Fail Max-Attempts: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Auth Type: Auth PAE State: Backend State: Dell# 11 3 30 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Initialize Initialize SSH Server and SCP Commands Dell Networking OS supports secure shell (SSH) protocol versions 1.5 and 2.0. SSH is a protocol for secure remote login over an insecure network.
PAGE 1280
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Added support for FIPS mode on the S4810. Version 8.3.7.
PAGE 1281
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.5(0.0) Related Commands Introduced on the Z9000, S6000, S4820T, S4810, MXL crypto key generate — Generate keys for SSH server debug ip ssh Enables collecting SSH debug information.
PAGE 1282
pre-Version 6.1.1.0 Usage Information Introduced on the E-Series. Debug information includes details for key-exchange, authentication, and established session for each connection. ip scp topdir Identify a location for files used in secure copy transfer. S6000 Syntax ip scp topdir directory To return to the default setting, use the no ip scp topdir command. Parameters directory Enter a directory name. Defaults The internal flash (flash:) is the default directory.
PAGE 1283
ip ssh authentication-retries Configure the maximum number of attempts that should be used to authenticate a user. S6000 Syntax Parameters ip ssh authentication-retries 1-10 1-10 Enter the number of maximum retries to authenticate a user. The range is from 1 to 10. The default is 3. Defaults 3 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1284
Defaults 10 per minute Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1285
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. If you enable this command, clients can log in without a password prompt. This command provides two levels of authentication: • rhost-authentication is done with the file specified in the ip ssh rhostfile command.
PAGE 1286
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The server-generated key is used for SSHv1 key-exchange. ip ssh password-authentication Enable password authentication for the SSH server. S6000 Syntax ip ssh password-authentication enable To disable password-authentication, use the no ip ssh passwordauthentication enable command.
PAGE 1287
ip ssh rekey Configures the time rekey-interval or volume rekey-limit threshold at which to re-generate the SSH key during an SSH session. Syntax ip ssh rekey [time rekey-interval] [volume rekey-limit] To reset to the default, use no ip ssh rekey [time rekey-interval] [volume rekey-limit] command. Parameters time minutes Enter the keywords time then the amount of time in minutes. The range is from 10 to 1440 minutes.
PAGE 1288
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication.
PAGE 1289
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1290
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1291
• 3des-cbc • aes128-cbc • aes192-cbc • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr The default cipher list is used. mac hmacalgorithm • 3des-cbc • aes128-cbc • aes192-cbc • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr Enter the keyword mac then a space-delimited list of hash message authentication code (HMAC) algorithms supported by the SSH server for keying hashing for the message authentication.
PAGE 1292
kex keyexchangealgorithm Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server. The following key exchange algorithms are available: • diffie-hellman-group-exchange-sha1 • diffie-hellman-group1-sha1 • diffie-hellman-group14-sha1 When FIPS is enabled, the default key-exchange-algorithm is diffie-hellman-group14-sha1.
PAGE 1293
Usage Information Version 9.5(0.0) Introduced the cipher, kex and mac options on the Z9000, S6000, S4820T, S4810, and MXL. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This command enables the SSH server and begins listening on a port.
PAGE 1294
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Usage Information Introduced on the S-Series and Z-Series. You can enable the SSH server on either a management VRF or a user defined VRF but not both.
PAGE 1295
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1296
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Usage Information If you configure a VRF for an SSH session, then you need not explicitly mention the same VRF for the SSH client sessions intended for that VRF.
PAGE 1297
Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information This command is useful if the remote SSH client implements Strict Host Key Checking. You can copy the host key to your list of known hosts.
PAGE 1298
Example Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 1299
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash://ADMIN_DIRssh/ knownhosts file. Example Dell#show ip ssh client-pub-keys poclab4,123.12.1.
PAGE 1300
vrf instance (OPTIONAL) E-Series Only: Enter the keyword vrf then the VRF Instance name to open an SSH connection to that instance. ipv4 address (OPTIONAL) Enter the IP address in dotted decimal format A.B.C.D. ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. -c encryption cipher Enter the following encryption cipher.
PAGE 1301
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Added support for the -c and -m parameters on the S4810. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Added IPv6 support. Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information Dell Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing.
PAGE 1302
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1303
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. S6000 Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1304
Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected. • For an 10/100 Ethernet interface, enter the keyword fastethernet.
PAGE 1305
ip dhcp snooping database renew Renew the binding table. S6000 Syntax ip dhcp snooping database renew Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1306
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable IP source guard. S6000 Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1307
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. When enabled, the system begins creating entries in the binding table for the specified VLANs. NOTE: Learning only happens if there is a trusted port in the VLAN. Related Commands ip dhcp snooping trust — configures an interface as trusted.
PAGE 1308
Role-Based Access Control Commands With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role. Users are granted permissions based on their user roles, not on their individual user ID. User roles are created for job functions and through those roles they acquire the permissions to perform their associated job function. This section describes the syntax and usage of RBAC-specific commands.
PAGE 1309
Related Commands 1. Locally define a system administrator user role.This will give you access to login with full permissions even if network connectivity to remote authentication servers is not available. 2. Configure login authentication on the console. This ensures that all users are properly identified through authentication no matter the access point 3. Specify an authentication method (RADIUS, TACACS+, or Local). 4. Specify authorization method (RADIUS, TACACS+ or Local). 5.
PAGE 1310
reset Enter the keyword reset to reset all roles back to default for that command. command Enter the command’s keywords to assign the command to a certain access level. You can enter one or more keywords. Defaults none Command Modes CONFIGURATION Command History Related Commands Version 9.5. (0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL userrole show role Display information on permissions assigned to a command, including user role and/or permission level.
PAGE 1311
Dell#show role mode configure management crypto-policy Role access: secadmin, sysadmin Related Commands userrole, username, privilege show userroles Display information on all defined user roles.
PAGE 1312
Defaults none Command Modes CONFIGURATION Command History Usage Information Version 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role from scratch. You then restrict commands or add commands to that role.
PAGE 1313
Service Provider Bridging 45 Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command line information (CLI) for the Dell Networking operating software Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel.
PAGE 1314
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces.
PAGE 1315
Parameters rate-limit rate Enter the keyword rate-limit followed by a number for the rate-limit for tunneled packets on the VMAN. The range is from 64 to 320. stp Enter the keyword stp to enable protocol tunneling on a spanning tree, including STP, MSTP, RSTP, and PVST. Defaults none Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guid.
PAGE 1316
Defaults The default destination MAC is 01:01:e8:00:00:00. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1317
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.4.1.0 Introduced Dell Networking OS must have the default CAM profile with the default microcode before you enable L2PT. protocol-tunnel rate-limit Enable traffic rate limiting per box. S6000 Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters rate Enter the rate in frames per second.
PAGE 1318
Related Commands show protocol-tunnel — displays tunneling information for all VLANs. show running-config — displays the current configuration. show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. S6000 Syntax Parameters show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094.
PAGE 1319
Gi1/2 Dell# Related Commands 2 STP, PVST show running-config — displays the current configuration.
PAGE 1320
sFlow 46 The Dell Networking operating software (OS) supports sFlow commands on the S6000 platform. Dell Networking operating software sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1321
sflow collector Configure a collector device to which sFlow datagrams are forwarded. S6000 Syntax sflow collector {ip-address | ipv6-address} agent-addr {ipaddress | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
PAGE 1322
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.3 Added support for IPv6 sFlow collectors and agents on the E-series TeraScale, C-Series, and S-Series. Version 8.4.1.1 Added support for IPv6 sFlow collectors and agents on the E-series ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced S-Series Stacking. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 1323
sflow enable (Global) Enable sFlow globally. S6000 Syntax sflow enable To disable sFlow, use the no sflow enable command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1324
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1325
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1326
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1327
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1328
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1329
Defaults The Global default sampling. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1330
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port-Channel Ethernet interface, enter the keyword port-channel then the slot/port information. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1331
Gi 3/40: configured rate 16384, actual rate 16384, subsampling rate 1 Dell# sFlow 1331
PAGE 1332
47 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on the S6000 platform. The chapter contains the following sections: • SNMP Commands • Syslog Commands SNMP Commands The following SNMP commands are available in the Dell Networking operating software.
PAGE 1333
show snmp Display the status of SNMP network elements. S6000 Syntax show snmp Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 1334
show snmp engineID Display the identification of the local SNMP engine and all remote engines that are configured on the router. S6000 Syntax show snmp engineID Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000.
PAGE 1335
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1336
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1337
> snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2. This is a port connected to IF-MIB::ifAlias.134792448 = STRING: !------command run on Dell Networkingswitch: --------------! Dell#snmp ifmib ifalias long !------command run on server connected to switch: --------------! > snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2.
PAGE 1338
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1339
NOTE: For IPv6 ACLs, only IPv6 and UDP types are valid for SNMP; TCP and ICMP rules are not valid for SNMP. In IPv6 ACLs, port rules are not valid for SNMP. Example Dell#config Dell(conf)# snmp-server community public ro Dell(conf)# snmp-server community guest ro security-name guestuser Dell(conf)# Example Dell(conf)# ip access-list standard snmp-ro-acl Dell(config-std-nacl)#seq 5 permit host 10.10.10.
PAGE 1340
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps. S6000 Syntax snmp-server enable traps [notification-type] [notificationoption] To disable traps, use the no snmp-server enable traps [notificationtype] [notification-option] command.
PAGE 1341
• supply • temperature For the snmp notification-type, enter one of the following optional parameters: • authentication • coldstart • linkdown • linkup Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 1342
snmp-server engineID Configure the name for both the local and remote SNMP engines on the router. S6000 Syntax snmp-server engineID [local engineID] [remote ip-address vrf vrf-name udp-port port-number engineID] To return to the default, use the no snmp-server engineID [local engineID] [remote ip-address vrf vrf-name udp-port port-number engineID] command. Parameters local engineID Enter the keyword local followed by the engine ID number that identifies the copy of the SNMP on the local device.
PAGE 1343
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Changing the value of the SNMP Engine ID has important side effects.
PAGE 1344
1 | 2c | 3 • v1v2creadg — maps to a community/security-name with ro permissions. • 1v2cwriteg — maps to a community/security-name rw permissions. (OPTIONAL) Enter the security model version number (1, 2c, or 3): • 1 is the least secure version. • 3 is the most secure of the security modes. • 2c allows transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. The default is 1.
PAGE 1345
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.2 Added support for the access parameter. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1346
ipv6-address Enter the keyword host then the IPv6 address of the host in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero. vrf vrf-name Enter the keyword vrf and then the name of the VRF that the SNMP server uses to connect to the host. NOTE: You can use this attribute to inform the SNMP engine about the vrf instance to be used to reach the corresponding remote host to send Trap or Inform message. If no VRF is specified, then the default VRF is used.
PAGE 1347
udp-port portnumber (OPTIONAL) Enter the keywords udp-port followed by the port number of the remote host to use. The range is from 0 to 65535. The default is 162. notificationtype (OPTIONAL) Enter one of the following keywords for the type of trap to be sent to the host: • bgp — Enable BGP state change traps. • ecfm — Enable ECFM state change traps. • entity — Enable entity change traps. • envmon — Enable SNMP environmental monitor traps.
PAGE 1348
Version 8.3.7.0 Introduced on the S4810. Version 8.4.1.0 Added support for VRRP traps. Version 7.6.1.0 Added support for STP and xSTP notification types. Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information In order to configure the router to send SNMP notifications, enter at least one snmp-server host command. If you enter the command with no keywords, all trap types are enabled for the host.
PAGE 1349
snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server. S6000 Syntax snmp-server location text To delete the SNMP location, use the no snmp-server location command. Parameters text Enter an alpha-numeric text string, up to 55 characters long. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1350
Defaults 8 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.
PAGE 1351
Defaults The IP address assigned to the management interface is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1352
Parameters name Enter the name of the user (not to exceed 20 characters), on the host that connects to the agent. group_name Enter a text string (up to 20 characters long) as the name of the group. The following groups are created for mapping to read/write community/security-names (defaults): • v1v2creadu — maps to a community with ro permissions. • 1v2cwriteu — maps to a community rw permissions.
PAGE 1353
priv des56 (OPTIONAL) Enter the keywords priv des56 to initiate a privacy authentication level setting using the CBC-DES privacy authentication algorithm (des56). priv password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the host to encrypt the contents of the message it sends to the agent. Minimum: eight characters long. access accesslist-name (Optional) Enter the standard IPv4 access list name (a string up to 16 characters long).
PAGE 1354
No default values exist for authentication or privacy algorithms and no default password exists. If you forget a password, you cannot recover it; the user must be reconfigured. You can specify either a plain-text password or an encrypted cyphertext password. In either case, the password is stored in the configuration in an encrypted form and displayed as encrypted in the show running-config command. If you have an encrypted password, you can specify the encrypted string instead of the plain-text password.
PAGE 1355
3] [encrypted] [auth {md5 | sha} auth-password] [priv {des56 | aes128–cfb} priv-password] [access access-list-name | ipv6 access-list-name | access-list-name ipv6 access-list-name] command. Parameters auth-password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the agent to receive packets from the host and to send packets to the host. Minimum: eight characters long.
PAGE 1356
snmp-server view Configure an SNMPv3 view. S6000 Syntax snmp-server view view-name oid-tree {included | excluded} To remove an SNMPv3 view, use the no snmp-server view view-name oidtree {included | excluded} command. Parameters view-name Enter the name of the view (not to exceed 20 characters). oid-tree Enter the OID sub tree for the view (not to exceed 20 characters). included (OPTIONAL) Enter the keyword included to include the MIB family in the view.
PAGE 1357
Example Dell# conf Dell#(conf) snmp-server view rview 1.3.6.1 included Related Commands show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF. Syntax snmp-server vrf vrf-name To undo the SNMP agent configuration, use the no snmp-server vrf vrfname command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate an SNMP agent with that VRF. Defaults Not Enabled.
PAGE 1358
Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1359
Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands show logging — displays logging settings and system messages in the internal buffer.
PAGE 1360
Defaults size = 40960; level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1361
E-Series legacy command Related Commands logging console — sets the logging console parameters. default logging monitor Return to the default settings for messages logged to the terminal. S6000 Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1362
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1363
vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to enable the logging process in VRF mode. NOTE: Use this attribute to specify the VRF that is used to contact the host. By default, the default VRF is used. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1364
logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. S6000 Syntax logging buffered [level] [size] To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffered command.
PAGE 1365
Usage Information When you decrease the buffer size, all messages stored in the buffer are lost. Increasing the buffer size does not affect messages stored in the buffer. Related Commands clear logging — clears the logging buffer. default logging buffered — returns the logging buffered parameters to the default setting. show logging — displays the logging setting and system messages in the internal buffer. logging console Specify which messages are logged to the console.
PAGE 1366
E-Series legacy command Related Commands clear logging — clears the logging buffer. default logging console — returns the logging console parameters to the default setting. show logging — displays the logging setting and system messages in the internal buffer. logging extended Logs security and audit events to a system log server. Syntax logging extended Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1367
logging facility Configure the Syslog facility used for error messages sent to Syslog servers. S6000 Syntax logging facility [facility-type] To return to the default values, use the no logging facility command.
PAGE 1368
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands logging — enables logging to a Syslog server. logging on — enables logging.
PAGE 1369
Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network management station. Related Commands show logging — displays information logged to the history buffer.
PAGE 1370
Usage Information When the number of messages reach the limit you set with the logging history size command, older messages are deleted as newer ones are added to the table. Related Commands show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications. S6000 Syntax logging monitor [level] To disable logging to terminal connections, use the no logging monitor command.
PAGE 1371
logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines. S6000 Syntax logging on To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1372
logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server. S6000 Syntax logging source-interface interface To disable this command and return to the default setting, use the no logging source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1373
Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Syslog messages contain the IP address of the interface used to egress the router. By configuring the logging source-interface command, the Syslog packets contain the IP address of the interface configured.
PAGE 1374
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you enable logging synchronous, unsolicited messages appear between software prompts and outputs. Only the messages with a severity at or below the set level are sent to the console.
PAGE 1375
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series, S55. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5.
PAGE 1376
Example Dell(conf)#logging version ? <0-1> Select syslog version (default = 0) Dell(conf)#logging version 1 show logging auditlog Displays an audit log. Syntax show logging auditlog Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.5(0.
PAGE 1377
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 1378
Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.200.12.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: neighbor 1.1.10.2 (Hold time expired) Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.200.14.7 Up Oct 8 09:26:25: %RPM1:RP1 %BGP-5-ADJCHANGE: neighbor 1.1.11.2 closed. Neighbor recycled Oct 8 09:26:25: %RPM1:RP1 %BGP-5-ADJCHANGE: neighbor 1.1.14.2 closed. Neighbor recycled --More-Example (History) Neighbor Neighbor 1.1.10.
PAGE 1379
Version 7.6.1.0 Usage Information Introduced on the S-Series. This command displays internal software driver information, which may be useful during troubleshooting switch initialization errors, such as a downed Port-Pipe. terminal monitor Configure the Dell Networking OS to display messages on the monitor/terminal. S6000 Syntax terminal monitor To return to default settings, use the terminal no monitor command. defaults Disabled.
PAGE 1380
48 SNMP Traps This chapter lists the traps sent by the Dell Networking operating software. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Message ID Trap Type Trap Option COLD_START SNMP COLDSTART WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP LINKDOWN SNMP LINKUP SNMP AUTH EGP_NEIGHBOR_LOSS SNMP NONE OSTATE_DOWN SNMP LINKDOWN SNMP LINKUP SNMP NONE SNMP NONE %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent.
PAGE 1381
Message ID Trap Type Trap Option SNMP NONE SNMP NONE NONE NONE ENVMON NONE ENVMON NONE ENVMON NONE CHM_CARD_PROBLEM ENVMON NONE CHM_ALARM_CUTOFF ENVMON NONE CHM_SFM_UP ENVMON NONE CHM_SFM_DOWN ENVMON NONE CHM_RPM_UP ENVMON NONE ENVMON NONE ENVMON NONE %RPM0-P:CP %SNMP-4-RMON_FALLING_THRESHOLD: RMON falling threshold alarm from SNMP OID RMON_HC_RISHING_THRESHOLD %RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID R
PAGE 1382
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON TEMP ENVMON TEMP %RAM-5-FAST_FAILOVER: RPM Failover Completed CHM_SFM_ADD %TSM-5-SFM_DISCOVERY: Found SFM 1 CHM_SFM_REMOVE %TSM-5-SFM_REMOVE: Removed SFM 1 CHM_MAJ_SFM_DOWN %CHMGR-0-MAJOR_SFM: Major alarm: Switch fabric down CHM_MAJ_SFM_DOWN_CLR %CHMGR-5-MAJOR_SFM_CLR: Major alarm cle
PAGE 1383
Message ID Trap Type Trap Option ENVMON TEMP ENVMON TEMP ENVMON FAN ENVMON FAN ENVMON FAN ENVMON FAN ENVMON NONE ENVMON NONE %CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC) CHM_MAJ_ALRM_TEMP %CHMGR-2-MAJOR_TEMP: Major alarm: chassis temperature high (%s temperature reaches or exceeds threshold of %dC) CHM_MAJ_ALRM_TEMP_CLR %CHMGR-2-MAJOR_TEMP_CLR: Major alarm cleared: chassis temperature lower (%s %d temperature is wi
PAGE 1384
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE %TME-2-ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CHM_CPU_THRESHOLD %CHMGR-5-CPU_THRESHOLD: Cpu %s usage above threshold. Cpu5SecUsage (%d) CHM_CPU_THRESHOLD_CLR %CHMGR-5-CPU_THRESHOLD_CLR: Cpu %s usage drops below threshold. Cpu5SecUsage (%d) CHM_MEM_THRESHOLD %CHMGR-5-MEM_THRESHOLD: Memory %s usage above threshold.
PAGE 1385
Storm Control 49 The Dell Networking operating software storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and SSeries). Storm control is supported on the Dell Networking S6000 platforms. Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1386
show storm-control broadcast Display the storm control broadcast configuration. S6000 Syntax Parameters show storm-control broadcast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information.
PAGE 1387
show storm-control multicast Display the storm control multicast configuration. S6000 Syntax Parameters show storm-control multicast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: • For Fast Ethernet, enter the keyword Fastethernet then the slot/port information.
PAGE 1388
show storm-control unknown-unicast Display the storm control unknown-unicast configuration. S6000 Syntax Parameters show storm-control unknown-unicast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then y the slot/port information.
PAGE 1389
storm-control broadcast (Configuration) Configure the percentage of broadcast traffic allowed in the network. S6000 Syntax storm-control broadcast [packets_per_second in] To disable broadcast rate-limiting, use the no storm-control broadcast [packets_per_second in] command.
PAGE 1390
Version 6.5.1.0 Usage Information Introduced on the E-Series. Broadcast storm control is valid on Layer 2/Layer 3 interfaces only. Layer 2 broadcast traffic is treated as unknown-unicast traffic. storm-control broadcast (Interface) Configure the percentage of broadcast traffic allowed on an interface (ingress only). S6000 Syntax storm-control broadcast [packets_per_second in] To disable broadcast storm control on the interface, use the no storm-control broadcast [packets_per_second in] command.
PAGE 1391
storm-control multicast (Configuration) Configure the packets per second (pps) of multicast traffic allowed into the C-Series and S-Series networks only. S6000 Syntax storm-control multicast packets_per_second in To disable storm-control for multicast traffic into the network, use the no stormcontrol multicast packets_per_second in command. Parameters packets_per_se cond in Enter the packets per second of multicast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1392
storm-control multicast (Interface) Configure the percentage of multicast traffic allowed on an C-Series or S-Series interface (ingress only) network only. S6000 Syntax storm-control multicast packets_per_second in To disable multicast storm control on the interface, use the no storm-control multicast packets_per_second in command. Parameters packets_per_se cond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1393
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1394
• 100% allows all traffic into the interface. The decimal range is from 0.1 to 0.9. wred-profile name E-Series Only: (Optionally) Enter the keywords wredprofile followed by the profile name to designate a wredprofile. packets_per_se cond in C-Series and S-Series Only: Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554431. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 1395
Spanning Tree Protocol (STP) 50 The commands in this chapter configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the S6000 Dell Networking switch/routing platform. bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree. S6000 Syntax bridge-priority {priority-value | primary | secondary} To return to the default value, use the no bridge-priority command. Parameters priority-value Enter a number as the bridge priority value.
PAGE 1396
pre-Version 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs. S6000 Syntax Parameters bpdu-destination-mac-address [stp | gvrp] provider-bridge-group xstp Force STP, RSTP, and MSTP to use the Provider Bridge Group address as the destination MAC address in its BPDUs. gvrp Forces GVRP to use the Provider Bridge GVRP Address as the destination MAC address in its PDUs.
PAGE 1397
Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information. events (OPTIONAL) Enter the keyword events to debug STP events.
PAGE 1398
description Enter a description of the spanning tree. S6000 Syntax description {description} To remove the description from the spanning tree, use the no description {description} command. Parameters description Enter a description to identify the spanning tree (80 characters maximum). Defaults none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History This guide is platform-specific.
PAGE 1399
Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 1400
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. max-age — changes the wait time before STP refreshes protocol configuration information. hello-time — changes the time interval between BPDUs.
PAGE 1401
Related Commands Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. forward-delay — changes the wait time before STP transitions to the Forwarding state. max-age — changes the wait time before STP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge.
PAGE 1402
Related Commands Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. forward-delay — changes the wait time before STP transitions to the Forwarding state. hello-time — changes the time interval between BPDUs. protocol spanning-tree To enable and configure the spanning tree group, enter SPANNING TREE mode. S6000 Syntax protocol spanning-tree stp-id To disable the Spanning Tree group, use the no protocol spanning-tree stp-id command.
PAGE 1403
Usage Information STP is not enabled when you enter SPANNING TREE mode. To enable STP globally on the switch, use the no disable command from SPANNING TREE mode. Example Dell(conf)#protocol spanning-tree 0 Dell(config-stp)# Related Commands disable — disables spanning tree group 0. To enable spanning tree group 0, use the no disable command. show config Display the current configuration for the mode. Only non-default values display.
PAGE 1404
show spanning-tree 0 Display the spanning tree group configuration and status of interfaces in the spanning tree group. S6000 Syntax Parameters show spanning-tree 0 [active | brief | guard | interface interface | root | summary] 0 Enter 0 (zero) to display information about that specific spanning tree group. active (OPTIONAL) Enter the keyword active to display only active interfaces in spanning tree group 0.
PAGE 1405
Usage Information Version 8.4.2.1 Added support for the optional guard keyword on the CSeries, S-Series, and E-Series TeraScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Enable spanning tree group 0 prior to using this command. The following describes the show spanning-tree 0 command shown in the example. Field Description “Bridge Identifier...
PAGE 1406
Example Dell#show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
PAGE 1407
Usage Information Example (Guard) The following describes the show spanning-tree 0 guard command shown in the example. Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1408
portfast [bpduguard [shutdown-onviol ation]] Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails. Enter the optional keyword bpduguard to disable the port when it receives a BPDU. Enter the optional keyword shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled. priority priority Enter keyword priority then a number as the priority. The range is from zero (0) to 15. The default is 8.
PAGE 1409
Protocol (RSTP), Multiple Spanning Tree Protocol (MSTP), and Per-VLAN Spanning Tree Plus (PVST+). Root guard is supported on any STP-enabled port or port-channel except when used as a stacking port. When enabled on a port, root guard applies to all VLANs configured on the port. STP root guard and loop guard cannot be enabled at the same time on a port.
PAGE 1410
System Time and Date 51 The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, refer to the “Network Time Protocol” section of the Management chapter in the Dell Networking OS Configuration Guide.
PAGE 1411
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. You can change the order of the month and day parameters to enter the time and date as time day month year. In the switch, the hardware clock is separate from the software and is called the calendar.
PAGE 1412
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. In the switch, the hardware clock is separate from the software and is called the calendar. This hardware clock runs continuously.
PAGE 1413
end-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year. The range is from 1993 to 2035.
PAGE 1414
clock summer-time recurring Set the software clock to convert to daylight saving time on a specific day each year. S6000 Syntax clock summer-time time-zone recurring [start-week start-day start-month start-time end-week end-day end-month end-time [offset]] To delete a daylight saving time zone configuration, use the no clock summertime command. Parameters time-zone Enter the three-letter name for the time zone. This name is displayed in the show clock output. You can enter up to eight characters.
PAGE 1415
end-month Enter the name of one of the 12 months in English. end-time Enter the time in hours:minutes:seconds. For the hour variable, use the 24-hour format; example, 17:15:00 is 5:15 pm. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to 1440. The default is 60 minutes. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1416
clock timezone Configure a timezone for the switch. S6000 Syntax clock timezone timezone-name offset To delete a timezone configuration, use the no clock timezone command. Parameters timezonename Enter the name of the timezone. You cannot use spaces. offset Enter one of the following: • a number from 1 to 23 as the number of hours in addition to universal time coordinated (UTC) for the timezone. • a minus sign (-) then a number from 1 to 23 as the number of hours. Defaults Not configured.
PAGE 1417
debug ntp Display network time protocol (NTP) transactions and protocol messages for troubleshooting. S6000 Syntax debug ntp {adjust | all | authentication | events | loopfilter | packets | select | sync} To disable debugging of NTP transactions, use the no debug ntp {adjust | all | authentication | events | loopfilter | packets | select | sync} command. Parameters adjust Enter the keyword adjust to display information on NTP clock adjustments.
PAGE 1418
Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ntp authenticate Enable authentication of NTP traffic between the switch and the NTP time serving hosts. S6000 Syntax ntp authenticate To disable NTP authentication, use the no ntp authentication command. Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1419
ntp broadcast client Set up the interface to receive NTP broadcasts from an NTP server. S6000 Syntax ntp broadcast client To disable broadcast, use the no ntp broadcast client command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 1420
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1421
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.0 Added support for IPv6 multicast addresses. Version 8.3.7.0 Introduced on the S4810. pre-Version 6.1.1.0 Introduced on the E-Series. show calendar Display the current date and time based on the switch hardware clock. S6000 Syntax show calendar Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1422
Related Commands show clock — displays the time and date from the switch software clock. show clock Display the current clock settings. S6000 Syntax Parameters show clock [detail] detail (OPTIONAL) Enter the keyword detail to view the source information of the clock. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1423
Related Commands clock summer-time recurring — displays the time and date from the switch hardware clock. show calendar — displays the time and date from the switch hardware clock. show ntp associations Display the NTP master and peers. S6000 Syntax show ntp associations Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1424
Field Description • ~ means the peer is statically configured. remote Displays the remote IP address of the NTP peer. ref clock Displays the IP address of the remote peer’s reference clock. st Displays the peer’s stratum, that is, the number of hops away from the external time source. A 16 in this column means the NTP peer cannot reach the time source. when Displays the last time the switch received an NTP packet. poll Displays the polling interval (in seconds).
PAGE 1425
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The following describes the show ntp status command shown in the Example below.
PAGE 1426
52 Object Missing This object is not available in the repository. tunnel-mode Enable a tunnel interface. S6000 Syntax tunnel mode {ipip | ipv6 | ipv6ip}[decapsulate-any] To disable an active tunnel interface, use the no tunnel mode command. Parameters ipip Enable tunnel in RFC 2003 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv4 tunnel. ipv6 Enable tunnel in RFC 2473 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv6 tunnel.
PAGE 1427
Configuration of IPv6 commands over decapsulate-any tunnel causes an error. tunnel source Set a source address for the tunnel. S6000 Syntax tunnel source {ip-address | ipv6–address | interface-typenumber | anylocal} To delete the current tunnel source address, use the no tunnel source command. Parameters ip-address Enter the source IPv4 address in A.B.C.D format. ipv6–address Enter the source IPv6 address in X:X:X:X::X format.
PAGE 1428
to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the switch that is operationally Up. tunnel keepalive Configure the tunnel keepalive target, interval and attempts. S6000 Syntax tunnel keepalive {ip-address | ipv6-address}[interval {seconds}] [attempts {count | unlimited}] To disable the tunnel keepalive probes use the no tunnel keepalive command. Parameters ip-address ipv6 address Enter the IPv4 or IPv6 address of the peer to which the keepalive probes will be sent.
PAGE 1429
of the far end tunnel peer, rather than to the tunnel destination. This reduces the chance of both ends of the tunnel staying in keepalive down state. If both ends get into a keepalive down state that does not clear in a few seconds, then performing shutdown - no shutdown sequence on one end should bring both ends back to up. tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation.
PAGE 1430
If you configure any allow-remote , the tunnel source or tunnel mode commands fail if the outer header address family does not match that of the configured allowremote. Usage Information Allow-remote entries can be configured only on multipoint receive-only tunnels, that is tunnel mode includes decapsulate-any option. This command will fail if any bidirectional tunnel options are configured. Likewise, attempts to configure bidirectional tunnel options will fail if any allow-remote entries are configured.
PAGE 1431
tunnel flow-label Configure the method to set the IPv6 flow label value in the outer tunnel header. S6000 Syntax tunnel flow-label value To return to the default value of 0, use the no tunnel flow-label value command. Parameters value Enter a value to set the IPv6 flow label value in the tunnel header. The range is from 0 to 1048575. The default value is 0.
PAGE 1432
Usage Information A value of 0 copies the inner packet hop limit (ipv6) or time-to-live (ipv4) in the encapsulated packet to the tunnel header hop limit (ipv6) or time-to-live (ipv4) value. tunnel destination Set a destination endpoint for the tunnel. S6000 Syntax tunnel destination {ip-address | ipv6–address} To delete a tunnel destination address, use the no tunnel destination {ipaddress | ipv6–address} command. Parameters ip-address Enter the destination IPv4 address for the tunnel.
PAGE 1433
To set the tunnel back to default logical address use the no ip unnumbered command. If the tunnel was previously operational, the tunnel interface is operationally down unless you also configure the tunnel IPv6 address. Parameters interface-type interfacenumber Enter the interface type, followed by a slot number.
PAGE 1434
Parameters interface-type interfacenumber Enter the interface type, followed by the type, slot and port information. interface-type interfacenumber (OPTIONAL) Instead of entering the keyword interface followed by the interface type, slot and port information, as above, you can enter the interface type, followed by just a slot number. Defaults None. Command Modes INTERFACE TUNNEL Command History Usage Information Version 9.3(0.1) Introduced on the S6000 and Z9000. Version 9.4(0.
PAGE 1435
VLAN Stacking 53 With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell Networking operating software supports this feature on the S6000 platform. For more information about basic VLAN commands, refer to the Virtual LAN (VLAN) Commands section in the Layer 2 chapter.
PAGE 1436
dei enable Make packets eligible for dropping based on their DEI value. S6000 Syntax dei enable Defaults Packets are colored green; no packets are dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1437
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the C-Series and S-Series.
PAGE 1438
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Instroduces on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information You must first enable DEI for this configuration to take effect. Related Commands dei enable – Make packets eligible for dropping based on their DEI value. member Assign a stackable VLAN access or trunk port to a VLAN.
PAGE 1439
Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information You must enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. Related Commands vlan-stack compatible — enables stackable VLAN on a VLAN.
PAGE 1440
Usage Information WARNING: The following message displays to confirm the command: All non-default configurations on the related member ports ports () will be removed. Do you want to continue (y/n)? If you enter “y”, all non-default configurations on any member ports of the current stack group is removed when the unit is rebooted. vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network.
PAGE 1441
vlan-stack compatible Enable the stackable VLAN feature on a VLAN. S6000 Syntax vlan-stack compatible To disable the Stackable VLAN feature on a VLAN, use the no vlan-stack compatible command. Defaults Not configured. Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1442
5 Active Dell# M M M M Gi 13/4 Po1(Gi 13/14-15) Gi 13/18 Gi 13/5 vlan-stack dot1p-mapping Map C-Tag dot1p values to a S-Tag dot1p value. You can separate the C-Tag values by commas and dashed ranges are permitted. Dynamic mode CoS overrides any Layer 2 QoS configuration in case of conflicts.
PAGE 1443
vlan-stack protocol-type Define the stackable VLAN tag protocol identifier (TPID) for the outer VLAN tag (also called the VMAN tag). If you do not configure this command, Dell Networking OS assigns the value 0x9100. S6000 Syntax Parameters vlan-stack protocol-type number number Enter the hexadecimal number as the stackable VLAN tag. You may specify both bytes of the 2-byte S-Tag TPID. The range is from 0 to FFFF. The default is 9100.
PAGE 1444
Related Commands Number Resulting TPID 81 0x0081 8100 0x8100 portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays. vlan-stack trunk — specifies a Layer 2 port or port channel as a trunk port to the Stackable VLAN network. vlan-stack trunk Specify a Layer 2 port or port channel as a trunk port to the Stackable VLAN network.
PAGE 1445
Version 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, execute the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. Starting with Dell Networking OS version 7.8.1.
PAGE 1446
x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM Status Description * 1 Inactive 20 Active 100 Active Dell(conf-if-vl-20)# Example 2 Q Ports T Gi 0/42 M Gi 0/42 Dell(config)#vlan-stack protocol-type 88A8 Dell(config)#interface gigabitethernet 3/10 Dell(conf-if-gi-3/10)#no shutdown Dell(conf-if-gi-3/10)#switchport Dell(conf-if-gi-3/10)#vlan-stack access Dell(conf-if-gi-3/10)#exit Dell(config)#interface tenGigabitethernet 8/0 Dell(conf-if-te-10/0)#no shutdown Dell(conf-if-te-10/0)#po
PAGE 1447
Virtual Routing and Forwarding (VRF) 54 Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist on the same router at the same time. Virtual Routing and Forwarding (VRF) is supported on the S-Series platforms. ip unknown-unicast Enable IPv4 catch-all route. S6000 Syntax ip unknown-unicast [vrf vrf-name] To remove the IPv4 catch-all route (0.0.0.
PAGE 1448
Defaults Soft forwarding is enabled. Command Modes CONFIGURATION Command History Usage Information Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. All the default catch-all entries in the longest prefix match (LPM) table collect and transmit all unresolved IPv6 packets to the CPU, even if they are destined for unknown destinations. description Enables you to specify a descriptive name for a customer VRF.
PAGE 1449
ip vrf forwarding Enables you to attach an interface to a VRF. Syntax ip vrf forwarding {vrf-name | management} To delete an interface associated with a configured VRF, use the no ip vrf forwarding {vrf-name | management} command. Parameters vrf-name Enter the name of the VRF that you want to create. management Enter the name of the management VRF. Defaults None (Interface is part of default VRF). Command Modes INTERFACE-CONFIG Command History This guide is platform-specific.
PAGE 1450
interfaces are assigned to different VRFs. If two interfaces are assigned to the same VRF, you cannot configure overlapping IP subnets or the same IP address on them. Example Dell#int gi 1/10 Dell#show config ! interface GigabitEthernet 1/10 no ip address shutdown Dell# Dell#ip vrf ? Dell#ip vrf forwarding East Dell#show config ! interface GigabitEthernet 1/10 ip vrf forwarding East no ip address shutdown Dell# interface management Associates a management port with a management VRF.
PAGE 1451
maximum dynamic-routes Specify the maximum number of dynamic (protocol) routes a VRF can have. S6000 Syntax maximum dynamic-routes limit {warn-threshold threshold-value | warning-only} To remove the limit on the maximum number of routes used, use the no maximum dynamic-routes command. Parameters limit Maximum number of routes allowed in a VRF. Valid range is from 1 to 16,000 (or maximum allowable for that platform if smaller value).
PAGE 1452
show ip vrf Displays information corresponding to the VRFs that are configured in the system. Syntax Parameters show ip [vrf vrf-name] vrf vrf-name Enter the keyword vrf and then the name of the VRF to display information corresponding to that VRF.. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1453
show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax Parameters show run vrf vrf-name vrf vrf-name Enter the keyword vrf and then the name of the VRF.. Command Modes • Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. EXEC The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.
PAGE 1454
55 VLT Proxy Gateway This chapter describes the VLT Proxy Gateway feature. proxy-gateway lldp Configure the LLDP proxy gateway S6000 Syntax proxy-gateway lldp Command Modes VLT DOMAIN Command History Usage Information Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch.
PAGE 1455
proxy-gateway static Configure the VLT static proxy gateway S6000 Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Information When proxy-gateway static configuration is made, the setting is saved in the Layer 2 application.
PAGE 1456
Command Modes Command History VLT DOMAIN PROXY GW STATIC Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Information You can configure the remote MAC address of the VLT peer to be associated with the static VLT proxy gateway and exclude a VLAN or a range of VLANs from proxy routing. This parameter is for a static VLT proxy gateway configuration.
PAGE 1457
Example Dell(conf)#vlt-domain 1 Dell(conf-vlt-domain)#proxy-gateway lldp Dell(conf-vlt-domain-proxy-gw-lldp)#peer-domain-link portchannel 20 exclude-vlan 3 proxy-gateway peer-timeout Configure the proxy-gateway VLT peer timeout value. S6000 Syntax Parameters Command Modes Command History [no] peer-timeout value value Enter the timeout value in seconds. The range is from 1 to 65535. The default is infinity. VLT DOMAIN PROXY GW LLDP Version 9.4(0.
PAGE 1458
Usage Information In a square VLT topology with only one link connecting remote peers, if you configure this command, any node has to send its VLT peer’s MAC address along with its own MAC address to the remote VLT domain. By default, a node will send only its own MAC address to the remote VLT domain. This parameter is applicable for an LLDP proxy gateway configuration. Example Dell(conf-vlt-domain-proxy-gw-lldp)# vlt-peer-mac transmit show vlt-proxy-gateway Display the VLT proxy gateway configuration.
PAGE 1459
Example Dell(conf)#do sh vlt proxy-gateway info static Mac Address Exclude Vlan ---------------------00:01:e8:8b:1c:c0 Dell#show vlt proxy-gateway info LagId Mac Address --------------Po 55 00:01:e8:8a:e8:f7 learnt via port-channel 55 Po 55 00:01:e8:8b:1c:c0 VLT Proxy Gateway lldp Exclude Vlan -----------3,7-8 << Macs 3,7-8 1459
PAGE 1460
56 Virtual Link Trunking (VLT) Virtual link trunking (VLT) is supported on the S6000 platform. VLT allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1461
ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format. interval seconds Enter the keyword interval to specify the time interval to send hello messages. The range is from 1 to 5 seconds. The default is 1 second. Defaults 1 second Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1462
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.2(0.2) Added multicast and ndp parameters. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 1463
Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 1464
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 1465
multicast peer-routing timeout Configure the time for a VLT node to retain synced multicast routes or synced multicast outgoing interface (OIF) after a VLT peer node failure. S6000 Syntax multicast peer-routing timeout value To restore the default value, use the no multicast peer-routing timeout command. Parameters value Enter the timeout value in seconds. The range is from 1 to 1200. The default is 150. Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific.
PAGE 1466
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 1467
Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. peer-routing-timeout Configure the delay after which peer routing is disabled when the peer is unavailable. This command is applicable for both IPV6/ IPV4. S6000 Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value in seconds. The range is from 1 to 65535. The default value is 0 (no timeout).
PAGE 1468
Default 32768 Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.
PAGE 1469
Usage Information The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell Networking OS version number. VLT version numbers are begin with odd numbers such as 3 or 5.
PAGE 1470
HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 3 34998 1026 1025 show vlt counters Displays the counter information. S6000 Syntax Parameters show vlt counters [arp| igmp-snoop | interface | mac | ndp] arp Enter the keyword arp to display the ARP counter information for the VLT. igmp-snoop Enter the keywords igmp-snoop to display the igmpsnooping counter information for the VLT.
PAGE 1471
------------------------L2 Total MAC-Address Count : IGMP MRouter Vlans count : IGMP Mcast Groups count : ARP entries count : Example (igmp-snoop) Dell# show vlt counter igmp-snoop Total IGMP VLT counters ---------------------IGMP MRouter Vlans count : 1 IGMP Mcast Groups count : 5 Example (igmp-snoop interface portchannel) Dell#show vlt counter igmp-snoop interface port-channel 2 VLT Port-ID: 2 IGMP Counter ----------------------IGMP MRouter Vlans count : 0 IGMP Mcast Groups count : 5 Dell# show vlt cou
PAGE 1472
The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810.
PAGE 1473
show vlt mismatch Display mismatches in VLT parameters. S6000 Syntax show vlt mismatch Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1474
show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. S6000 Syntax show vlt role Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1475
show vlt statistics Displays statistics on VLT operations. S6000 Syntax Parameters show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] domain Display the VLT statistics for the domain. multicast Display the VLT statistics for multicast. mac Display the VLT statistics for the MAC address. arp Display the VLT statistics for ARP. igmp-snoop Display the VLT statistics for IGMP snooping. ndp Display the VLT statistics for NDP. Default Not configured.
PAGE 1476
ICL Hello's Received: Domain Mismatch Errors: Version Mismatch Errors: Config Mismatch Errors: 910 0 0 0 VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg R
PAGE 1477
show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. S6000 Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 1478
Defaults Automatically assigned based on the MAC address of each VLT peer. The peer with the lower MAC address is assigned unit 0; the peer with the higher MAC address is assigned unit 1. Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.
PAGE 1479
The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810. Usage Information The VLT domain ID must be the same between the two VLT devices.
PAGE 1480
Version 8.3.8.0 1480 Introduced on the S4810.
PAGE 1481
Virtual Extensible LAN (VXLAN) 57 Virtual Extensible LAN (VXLAN) is supported on the S6000 platform. feature vxlan Enable VXLAN configuration globally on the platform. S6000 Syntax feature vxlan To disable the VXLAN, use the no feature vxlan command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.
PAGE 1482
Command Modes Command History EXEC Privilege Version 9.4(0.0) Introduced on the S6000. fail-mode Configures failure-mode on the platform. S6000 Syntax fail-mode secure To disable the fail-mode secure, use the no fail-mode securecommand. Parameters secure Enter the keyword secure to delete all its database and hardware flows/resources, when the VTEP loses connectivity with the controller. Defaults non secure Command Modes VXLAN INSTANCE Command History This guide is platform-specific.
PAGE 1483
To delete vxlan-instance from the system, use no vxlan-instance 1 command. Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Introduced on the S6000.
PAGE 1484
Usage Information You must disable vxlan-instance before unconfiguring VAP. Related Commands feature vxlan—Enable VXLAN configuration globally on the platform. max_backoff Configures time to wait between connection attempts with controller. S6000 Syntax Parameters max_backoff time time Enter the time in milliseconds. The range is from 1000-180000. The default value is 30000. Defaults 30000 Command Modes VXLAN INSTANCE Command History This guide is platform-specific.
PAGE 1485
Defaults Disabled Command Modes VXLAN INSTANCE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Introduced on the S6000. Usage Information Related Commands vxlan-instance— Enable VXLAN Instance configuration on the platform. controller Configures controller for the VXLAN instance on the platform.
PAGE 1486
Command Modes VXLAN INSTANCE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Introduced on the S6000. Usage Information Related Commands vxlan-instance — Enable VXLAN instance configuration on the platform. show vxlan vxlan-instance Displays information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1487
Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show running-config vxlan Displays the configuration information of the VXLAN on S6000. S6000 Syntax show running-config vxlan Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Introduced on the S6000.
PAGE 1488
Command Modes Command History name (Optional) Enter the name of VXLAN logical network with a maximum length of 30 characters. vnidVNID (Optional) Enter the keyword vnid and then enter the ID of the VXLAN. The range is from 1 to 16777215. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Introduced on the S6000.
PAGE 1489
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Example Dell# show vxlan vxlan-instance <1> unicast-mac-local Total Local Mac Count: 5 VNI MAC PORT 4656 4656 4656 4656 4656 Related Commands Introduced on the S6000.
PAGE 1490
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version 9.4. (0.0) Example Introduced on the S6000.
PAGE 1491
Version 9.4. (0.0) Introduced on the S6000. Example Dell#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance logical network Displays logical network information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1492
VFI : 28674 Unknown Multicast MAC Tunnels: 192.168.122.133 : vxlan_over_ipv4 (up) Port Vlan Bindings: Te 0/80: VLAN: 0 (0x80000001), Fo 0/124: VLAN: 0 (0x80000004), Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform. clear vxlan vxlan-instance statistics Syntax Parameters clear vxlan vxlan-instance instance ID statistics instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release.
PAGE 1493
Virtual Router Redundancy Protocol (VRRP) 58 Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on the S6000 platform. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. S6000 Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter a number of seconds. The range is from 1 to 255.
PAGE 1494
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers.
PAGE 1495
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The given password is encrypted by the system and the show config displays an encrypted text string for any of the encrypted typed used. clear counters vrrp Clear the counters maintained on VRRP operations.
PAGE 1496
Example Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell#clear counters vrrp vrf jay Clear "show vrrp" counters of all vrrp groups on all interfaces in VRF jay [confirm] yes debug vrrp Allows you to enable debugging of VRRP.
PAGE 1497
ipv6 Enter the keyword ipv6 to enable debugging for IPv6. packets Enter the keyword packets to enable debugging of VRRP control packets. state Enter the keyword state to enable debugging of VRRP state changes. timer Enter the keyword timer to enable debugging of the VRRP timer. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1498
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. disable Disable a VRRP group.
PAGE 1499
hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router. By delaying the initialization of the VRRP MASTER, the new switch can stabilize its routing tables. S6000 Syntax hold-time {seconds | centisecs centisecs} To return to the default value, use the no hold-time command. Parameters seconds Enter the number of seconds. The range is from 0 to 65535. The default is zero (0) seconds.
PAGE 1500
preempt To preempt or become the MASTER router, permit a BACKUP router with a higher priority value. S6000 Syntax preempt To prohibit preemption, use the no preempt command. Defaults Enabled (that is, a BACKUP router can preempt the MASTER router). Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1501
Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.16.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1502
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell(conf-if-vrid-4)#show con vrrp-group 4 virtual-address 119.192.182.124 ! show vrrp View the VRRP groups that are active. If no VRRP groups are active, the FTOS returns No Active VRRP group.
PAGE 1503
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1504
Item Description • BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router. Virtual addr(s) Displays the virtual IP addresses of the VRRP routers associated with the interface. Example (Brief) Dell>Interface Grp Pri Pre State Master addr Virtual addr(s) Description----------------------------------------------------------Gi 10/37 1 100 Y Master 200.200.200.200 200.200.200.201 Gi 10/37 2 100 Y Master 200.200.200.200 200.200.200.202 200.200.
PAGE 1505
Item Description • Gratuitous ARP sent displays the number of gratuitous ARPs sent. Virtual MAC address Displays the virtual MAC address of the VRRP group. Virtual IP address Displays the virtual IP address of the VRRP router to which the interface is connected. Authentication:... States whether authentication is configured for the VRRP group. If it is, the authentication type and the password are listed. Tracking states.. This line is displayed if the track command is configured on an interface.
PAGE 1506
00:00:5e:00:01:14 Virtual IP address: 10.0.0.2 Authentication: (none) FTOS#show vrrp vrf jay brief Interface Group Pri Pre State Master addr Virtual addr(s) Description ------------------------------------------------------------------------------------------------Fo 0/124 IPv4 20 100 Y Master 10.0.0.3 10.0.0.2 Dell# virtual-address Configure up to 12 IP addresses of virtual routers in the VRRP group. To start sending VRRP packets, set at least one virtual address for the VRRP group.
PAGE 1507
Usage Information Version 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. pre-Version 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when a virtual IP address is configured. When you delete the virtual address, the VRRP group stops sending VRRP packets. A system message appears after you enter or delete the virtual-address command.
PAGE 1508
Usage Information Related Command This command applies to a single interface. When used with the vrrp delay reload CLI, the later timer rules the VRRP enabling. For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 1509
• When an interface comes up, whether as part of a system reload or an interface reload, the system waits 300 seconds (5 minutes) to bring up VRRP on that interface. Save the configuration and reload the system for the delay timers to take effect. Related Command vrrp delay minimum — sets the delay time for VRRP initialization after a line card reboot. vrrp-group Assign a VRRP ID to an interface. You can configure up to 12 VRRP groups per interface.
PAGE 1510
version Set VRRP protocol version for IPv4 group. Syntax version {2 | 3 | both} To return to the default setting, use the no version command. Parameters 2 Enter the 2 parameter to specify VRRP version 2 as defined by RFC 3768, Virtual Router Redundancy Protocol. 3 Enter the 2 parameter to specify VRRP version 3 as defined in RFC 5798, Virtual Router Redundancy. both Enter the both keyword for in-service migration from VRRP version 2 to VRRP version 3.