Users Guide

In the above example, stack unit 1 is the master management unit, stack unit 2 is the standby unit. The cables are connected to each unit.
Congure the stack groups on the units in the following order:
• Congure the rst stack group on unit 1: stack-unit 1 stack-group 13
• Congure the stack groups on unit 2: stack-unit 2 stack-group 14 and stack-unit 2 stack-group 15
• Congure the stack groups on unit 3: stack-unit 3 stack-group 12 and stack-unit 3 stack-group 13
• Congure the stack groups on unit 4: stack-unit 4 stack-group 13 and stack-unit 4 stack-group 31
• Congure the nal stack-group on unit 1 to complete the stack: stack-unit 1 stack-group 31
When the stack-group conguration is complete, the system prints a syslog for reload.
Dell#configure
Dell(conf)#stack-unit 4 stack-group 13
Dell(conf)#02:39:12: %STKUNIT4-M:CP %IFMGR-6-STACK_PORTS_ADDED: Ports Fo 4/52 have been
configured as
stacking ports. Please save and reload for config to take effect
Dell(conf)#stack-unit 4 stack-group 14
Dell(conf)#02:39:15: %STKUNIT4-M:CP %IFMGR-6-STACK_PORTS_ADDED: Ports Fo 4/56 have been
configured as
stacking ports. Please save and reload for config to take effect
Dell(conf)#
Dell#02:39:18: %STKUNIT4-M:CP %SYS-5-CONFIG_I: Configured from console
Dell(conf)#stack-unit 5 stack-group 28
Dell(conf)#1d16h8m: %STKUNIT5-M:CP %IFMGR-6-STACK_PORTS_ADDED: Ports Fo 5/112 have been
configured as stacking ports. Please save and reset stack-unit 5 for config to take effect
Dell(conf)#stack-unit 0 stack-group 29
Dell(conf)#1d16h8m: %STKUNIT5-M:CP %IFMGR-6-STACK_PORTS_ADDED: Ports Fo 0/116 have been
configured as stacking ports. Please save and reset stack-unit 0 for config to take effect
Reload each unit in the stack. After the reload is complete, the four units come up as a stack with unit 1 as the management unit, unit 2 as
the standby unit, and the remaining units as stack-members. All units in the stack can be accessed from the management unit.
NOTE
: Before executing show commands, you must wait for 10 to 15 seconds for the download-agent process to start.
To view the stack unit information after the reload, use the show system brief command.
Dell#show system brief
Stack MAC : 90:b1:1c:f4:a7:c7
Reload-Type : normal-reload [Next boot : normal-reload]
-- Stack Info --
Unit UnitType Status ReqTyp CurTyp Version Ports
------------------------------------------------------------------------------------
0 Member not present S6000
1 Member not present
2 Standby online S6000 S6000 1-0(0-3387) 128
3 Member not present S6000
4 Member not present
5 Management online S6000 S6000 1-0(0-3387) 128
-- Power Supplies --
Unit Bay Status Type FanStatus FanSpeed(rpm)
---------------------------------------------------------------------------
2 0 up AC up 6720
2 1 up AC up 6688
5 0 up AC up 6688
5 1 down UNKNOWN down 0
-- Fan Status --
Unit Bay TrayStatus Fan0 Speed Fan1 Speed
------------------------------------------------------------------------------------
2 0 up up 7072 up 6971
2 1 up up 7021 up 7021
2 2 up up 7021 up 6971
Stacking
871