Dell Configuration Guide for the S6000 System 9.8(0.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 About this Guide............................................................................................................ 32 Audience.......................................................................................................................................................................... 32 Conventions.....................................................................................................................................................................
Creating a Custom Privilege Level.............................................................................................................................. 54 Removing a Command from EXEC Mode...................................................................................................................54 Moving a Command from EXEC Privilege Mode to EXEC Mode................................................................................54 Allowing Access to CONFIGURATION Mode Commands...............
The Port-Authentication Process..................................................................................................................................... 78 EAP over RADIUS...................................................................................................................................................... 79 Configuring 802.1X...........................................................................................................................................................
Resequencing an ACL or Prefix List...........................................................................................................................113 Route Maps..................................................................................................................................................................... 114 Implementation Information.......................................................................................................................................
AS Number Migration............................................................................................................................................... 160 BGP4 Management Information Base (MIB)............................................................................................................. 161 Important Points to Remember..................................................................................................................................161 Configuration Information......
CAM Allocation.............................................................................................................................................................. 204 Test CAM Usage............................................................................................................................................................ 206 View CAM Profiles...............................................................................................................................................
Configure Enhanced Transmission Selection.................................................................................................................. 233 ETS Prerequisites and Restrictions...........................................................................................................................234 Creating an ETS Priority Group................................................................................................................................ 234 ETS Operation with DCBx.....
Drop DHCP Packets on Snooped VLANs Only......................................................................................................... 273 Dynamic ARP Inspection...........................................................................................................................................274 Configuring Dynamic ARP Inspection....................................................................................................................... 275 Source Address Validation...............
Optimizing the Boot Time.............................................................................................................................................. 299 Booting Process When Optimized Boot Time Mechanism is Enabled.......................................................................299 Guidelines for Configuring Optimized Booting Mechanism.......................................................................................
IGMP Protocol Overview................................................................................................................................................ 318 IGMP Version 2.........................................................................................................................................................318 IGMP Version 3.........................................................................................................................................................
Configuring Layer 3 (Interface) Mode....................................................................................................................... 341 Egress Interface Selection (EIS).....................................................................................................................................342 Important Points to Remember................................................................................................................................ 342 Configuring EIS.......
Configure the MTU Size on an Interface........................................................................................................................ 367 Port-Pipes......................................................................................................................................................................368 Auto-Negotiation on Ethernet Interfaces.......................................................................................................................
UDP Helper with Subnet Broadcast Addresses..............................................................................................................390 UDP Helper with Configured Broadcast Addresses.........................................................................................................391 UDP Helper with No Configured Broadcast Addresses................................................................................................... 391 Troubleshooting UDP Helper......................
Enable and Disable iSCSI Optimization...................................................................................................................... 417 Default iSCSI Optimization Values................................................................................................................................... 417 iSCSI Optimization Prerequisites.....................................................................................................................................
Configure a LAG on ALPHA...................................................................................................................................... 451 25 Layer 2...................................................................................................................... 459 Manage the MAC Address Table.................................................................................................................................... 459 Clearing the MAC Address Table....................
Configuring Transmit and Receive Mode........................................................................................................................484 Configuring a Time to Live............................................................................................................................................. 485 Debugging LLDP............................................................................................................................................................
Configure Multiple Spanning Tree Protocol.................................................................................................................... 520 Related Configuration Tasks.....................................................................................................................................520 Enable Multiple Spanning Tree Globally...........................................................................................................................
Graceful Restart...................................................................................................................................................... 559 Fast Convergence (OSPFv2, IPv4 Only)..................................................................................................................560 Multi-Process OSPFv2 with VRF.............................................................................................................................
Creating Multicast Boundaries and Domains.................................................................................................................. 605 35 PIM Source-Specific Mode (PIM-SSM)................................................................... 606 Implementation Information........................................................................................................................................... 606 Important Points to Remember............................................
Honoring dot1p Priorities on Ingress Traffic.............................................................................................................. 636 Configuring Port-Based Rate Policing...................................................................................................................... 637 Configuring Port-Based Rate Shaping......................................................................................................................637 Policy-Based QoS Configurations......
Configuring an RMON Event....................................................................................................................................679 Configuring RMON Collection Statistics.................................................................................................................. 680 Configuring the RMON Collection History...............................................................................................................
Configuring the SSH Server Cipher List....................................................................................................................710 Secure Shell Authentication...................................................................................................................................... 710 Troubleshooting SSH.................................................................................................................................................713 Telnet..............
sFlow Show Commands................................................................................................................................................. 745 Displaying Show sFlow Global...................................................................................................................................745 Displaying Show sFlow on an Interface.....................................................................................................................
Enabling and Disabling a Port using SNMP.....................................................................................................................768 Fetch Dynamic MAC Entries using SNMP......................................................................................................................768 Deriving Interface Indices...............................................................................................................................................
Related Configuration Tasks..................................................................................................................................... 796 Important Points to Remember...................................................................................................................................... 796 Configuring Interfaces for Layer 2 Mode........................................................................................................................
Get Help with Upgrades.................................................................................................................................................822 53 Virtual LANs (VLANs)............................................................................................... 823 Default VLAN................................................................................................................................................................. 823 Port-Based VLANs.......................
eVLT Configuration Example.......................................................................................................................................... 860 eVLT Configuration Step Examples.......................................................................................................................... 860 PIM-Sparse Mode Configuration Example.....................................................................................................................
View VRF Instance Information................................................................................................................................ 894 Assigning an OSPF Process to a VRF Instance........................................................................................................ 895 Configuring VRRP on a VRF Instance...................................................................................................................... 895 Configuring Management VRF...............
Enabling TCP Dumps..................................................................................................................................................... 952 60 Standards Compliance.............................................................................................. 953 IEEE Compliance............................................................................................................................................................953 RFC and I-D Compliance....................
1 About this Guide This guide describes the protocols and features the Dell Networking Operating System (OS) supports and provides configuration instructions and examples for implementing them. The S6000 platform is available with Dell Networking OS version 9.0 (2.0) and beyond. Though this guide contains information on protocols, it is not intended to be a complete reference. This guide is a reference for configuring protocols on Dell Networking systems.
2 Configuration Fundamentals The Dell Networking Operating System (OS) command line interface (CLI) is a text-based interface you can use to configure interfaces and protocols. The CLI is largely the same for each platform except for some commands and command outputs. The CLI is structured in modes for security and management purposes. Different sets of commands are available in each mode, and you can limit user access to modes using privilege levels.
Beneath CONFIGURATION mode are submodes that apply to interfaces, protocols, and features. The following example shows the submode command structure. Two sub-CONFIGURATION modes are important when configuring the chassis for the first time: • • INTERFACE submode is the mode in which you configure Layer 2 and Layer 3 protocols and IP services specific to an interface.
uBoot ROUTER OSPFV3 ROUTER RIP SPANNING TREE TRACE-LIST VLT DOMAIN VRRP UPLINK STATE GROUP Navigating CLI Modes The Dell Networking OS prompt changes to indicate the CLI mode. The following table lists the CLI mode, its prompt, and information about how to access and exit the CLI mode. Move linearly through the command modes, except for the end command which takes you directly to EXEC Privilege mode and the exit command which moves you up one command mode level.
CLI Command Mode Prompt Access Command VLAN Interface Dell(conf-if-vl-1)# interface (INTERFACE modes) STANDARD ACCESS-LIST Dell(config-std-nacl)# ip access-list standard (IP ACCESS-LIST Modes) EXTENDED ACCESS-LIST Dell(config-ext-nacl)# ip access-list extended (IP ACCESS-LIST Modes) IP COMMUNITY-LIST Dell(config-community-list)# ip community-list AUXILIARY Dell(config-line-aux)# line (LINE Modes) CONSOLE Dell(config-line-console)# line (LINE Modes) VIRTUAL TERMINAL Dell(config-line-vty
CLI Command Mode Prompt Access Command ECMP Dell(conf-ecmp-group-ecmpgroup-id)# ecmp-group EIS Dell(conf-mgmt-eis)# management egress-interfaceselection FRRP Dell(conf-frrp-ring-id)# protocol frrp LLDP Dell(conf-lldp)# or Dell(confif—interface-lldp)# protocol lldp (CONFIGURATION or INTERFACE Modes) LLDP MANAGEMENT INTERFACE Dell(conf-lldp-mgmtIf)# management-interface (LLDP Mode) LINE Dell(config-line-console) or Dell(config-line-vty) line console orline vty MONITOR SESSION Dell(conf-m
Reload-Type : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Management online S4810 S4810 9.4(0.
Obtaining Help Obtain a list of keywords and a brief functional description of those keywords at any CLI mode using the ? or help command: • To list the keywords available in the current mode, enter ? at the prompt or after a keyword. • Enter ? after a prompt lists all of the available keywords. The output of this command is the same for the help command.
Short-Cut Key Combination Action CNTL-N Return to more recent commands in the history buffer after recalling commands with CTRL-P or the UP arrow key. CNTL-P Recalls commands, beginning with the last command. CNTL-R Re-enters the previous command. CNTL-U Deletes the line. CNTL-W Deletes the previous word. CNTL-X Deletes the line. CNTL-Z Ends continuous scrolling of command outputs. Esc B Moves the cursor back one word. Esc F Moves the cursor forward one word.
Example of the except Keyword Dell#show system brief | except 0 Slot Status NxtBoot ReqTyp CurTyp Version Ports ----------------------------------------------------2 not present 3 not present 4 not present 5 not present 6 not present The find keyword displays the output of the show command beginning from the first occurrence of specified text. The following example shows this command used in combination with the show linecard all command.
• On the system that telnets into the switch, this message appears: % Warning: The following users are currently configuring the system: User "" on line console0 • On the system that is connected over the console, this message appears: % Warning: User "" on line vty0 "10.11.130.
3 Getting Started This chapter describes how you start configuring your system. When you power up the chassis, the system performs a power-on self test (POST) during which the line card status light emitting diodes (LEDs) blink green. The system then loads the Dell Networking Operating System (OS). Boot messages scroll up the terminal window during this process. No user interaction is required if the boot process proceeds without interruption.
• 8 data bits • 1 stop bit • No flow control Pin Assignments You can connect to the console using a RJ-45 to RJ-45 rollover cable and a RJ-45 to DB-9 female DTE adapter to a terminal server (for example, a PC). The pin assignments between the console and a DTE terminal server are as follows: Table 2.
• You can manage all Dell Networking products in-band via the front-end data ports through interfaces assigned an IP address as well. Accessing the System Remotely Configuring the system for remote access is a three-step process, as described in the following topics: 1. Configure an IP address for the management port. Configure the Management Port IP Address 2. Configure a management route with a default gateway. Configure a Management Route 3. Configure a username and password.
* 0 is for inputting the password in clear text. * 7 is for inputting a password that is already encrypted using a Type 7 hash. Obtaining the encrypted password from the configuration of another Dell Networking system. Configuring the Enable Password Access EXEC Privilege mode using the enable command. EXEC Privilege mode is unrestricted by default. Configure a password as a basic security measure.
Location source-file-url Syntax destination-file-url Syntax copy scp://{hostip | hostname}/filepath/ filename scp://{hostip | hostname}/ filepath/filename TFTP server For a remote file location: SCP server Important Points to Remember • You may not copy a file from one remote system to another. • You may not copy a file from one location to the same location. • When copying to a server, you can only use a hostname if a domain name server (DNS) server is configured.
Table 5. Forming a copy Command Location source-file-url Syntax destination-file-url Syntax For a remote file location: copy nfsmount://{}/filepath/filename} username:password tftp://{hostip | hostname}/ filepath/filename NFS File System Important Points to Remember • You cannot copy a file from one remote system to another. • You cannot copy a file from one location to the same location.
Save the Running-Configuration The running-configuration contains the current system configuration. Dell Networking recommends coping your runningconfiguration to the startup-configuration. The commands in this section follow the same format as those commands in the Copy Files to and from the System section but use the filenames startup-configuration and running-configuration. These commands assume that current directory is the internal flash, which is the system default.
2 drwx 512 3 drw8192 4 drw8192 5 drw8192 6 drw8192 7 d--8192 8 -rw- 33059550 9 -rw- 27674906 10 -rw- 27674906 11 drw8192 12 -rw7276 13 -rw7341 14 -rw- 27674906 15 -rw- 27674906 --More-- Jul Mar Mar Mar Mar Mar Jul Jul Jul Jan Jul Jul Jul Jul 23 30 30 30 30 30 11 06 06 01 20 20 06 06 2007 1919 1919 1919 1919 1919 2007 2007 2007 1980 2007 2007 2007 2007 00:38:44 10:31:04 10:31:04 10:31:04 10:31:04 10:31:04 17:49:46 00:20:24 19:54:52 00:18:28 01:52:40 15:34:46 19:52:22 02:23:22 ..
Dell#show file-systems Size(b) Free(b) Feature Type Flags 520962048 213778432 dosFs2.0 USERFLASH 127772672 21936128 dosFs2.0 USERFLASH - network - network - network Prefixes rw flash: rw slot0: rw ftp: rw tftp: rw scp: You can change the default file system so that file management commands apply to a particular device or memory. To change the default directory, use the following command. • Change the default directory.
NOTE: To enable HTTP to be VRF-aware, as a prerequisite you must first define the VRF. You can specify either the management VRF or a nondefault VRF to configure the VRF awareness setting. When you specify the management VRF, the copy operation that is used to transfer files to and from an HTTP server utilizes the VRF table corresponding to the Management VRF to look up the destination. When you specify a nondefault VRF, the VRF table corresponding to that nondefault VRF is used to look up the HTTP server.
Examples: Without Entering the Hash Value for Verification MD5 Dell# verify md5 flash://FTOS-SE-9.5.0.0.bin MD5 hash for FTOS-SE-9.5.0.0.bin: 275ceb73a4f3118e1d6bcf7d75753459 SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.bin SHA256 hash for FTOS-SE-9.5.0.0.bin: e6328c06faf814e6899ceead219afbf9360e986d692988023b749e6b2093e933 Examples: Entering the Hash Value for Verification MD5 Dell# verify md5 flash://FTOS-SE-9.5.0.0.bin 275ceb73a4f3118e1d6bcf7d75753459 MD5 hash VERIFIED for FTOS-SE-9.5.0.0.
4 Management This chapter describes the different protocols or services used to manage the Dell Networking system. Configuring Privilege Levels Privilege levels restrict access to commands based on user or terminal line. There are 16 privilege levels, of which three are pre-defined. The default privilege level is 1. Level Description Level 0 Access to the system begins at EXEC mode, and EXEC mode commands are limited to enable, disable, and exit.
level level command. In the command, specify the privilege level of the user or terminal line and specify all the keywords in the command to which you want to allow access. Allowing Access to the Following Modes This section describes how to allow access to the INTERFACE, LINE, ROUTE-MAP, and ROUTER modes. Similar to allowing access to CONFIGURATION mode, to allow access to INTERFACE, LINE, ROUTE-MAP, and ROUTER modes, you must first allow access to the command that enters you into the mode.
Dell#show priv Current privilege level is 3. Dell#? capture Capture packet configure Configuring from terminal disable Turn off privileged commands enable Turn on privileged commands exit Exit from the EXEC ip Global IP subcommands monitor Monitoring feature mtrace Trace reverse multicast path from destination to source ping Send echo messages quit Exit from the EXEC show Show running system information [output omitted] Dell#config [output omitted] Dell(conf)#do show priv Current privilege level is 3.
Applying a Privilege Level to a Terminal Line To set a privilege level for a terminal line, use the following command. • Configure a privilege level for a user. CONFIGURATION mode username username privilege level NOTE: When you assign a privilege level between 2 and 15, access to the system begins at EXEC mode, but the prompt is hostname#, rather than hostname>. Configuring Logging The Dell Networking OS tracks changes in the system using event and error messages.
The audit log contains configuration events and information. The types of information in this log consist of the following: • User logins to the switch. • System events for network issues or system issues. • Users making configuration changes. The switch logs who made the configuration changes and the date and time of the change. However, each specific change on the configuration is not logged. Only that the configuration was modified is logged with the user ID, date, and time of the change.
line vty0 ( 10.14.1.91 ) Clearing Audit Logs To clear audit logs, use the clear logging auditlog command in Exec mode. When RBAC is enabled, only the system administrator user role can issue this command. Example of the clear logging auditlog Command Dell# clear logging auditlog Configuring Logging Format To display syslog messages in a RFC 3164 or RFC 5424 format, use the logging version [0 | 1} command in CONFIGURATION mode. By default, the system log version is set to 0.
Setting Up a Secure Connection to a Syslog Server You can use reverse tunneling with the port forwarding to securely connect to a syslog server. Pre-requisites To configure a secure connection from the switch to the syslog server: 1. On the switch, enable the SSH server Dell(conf)#ip ssh server enable 2.
Log Messages in the Internal Buffer All error messages, except those beginning with %BOOTUP (Message), are log in the internal buffer.
– Add line on a 5.7 SunOS UNIX system. local7.debugging /var/adm/ftos.log In the previous lines, local7 is the logging facility level and debugging is the severity level. Track Login Activity Dell Networking OS enables you to track the login activity of users and view the successful and unsuccessful login events.
Last login location: Line vty0 ( 10.14.1.97 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 3 -----------------------------------------------------------------Example of the show login statistics all command The show login statistics all command displays the successful and failed login details of all users in the last 30 days or the custom defined time period.
Configuring Concurrent Session Limit To configure concurrent session limit, follow this procedure: • Limit the number of concurrent sessions for all users. CONFIGURATION mode login concurrent-session limit number-of-sessions Example of Configuring Concurrent Session Limit The following example limits the permitted number of concurrent login sessions to 4.
5 vty 3 10.14.1.97 Kill existing session? [line number/Enter to cancel]: Changing System Logging Settings You can change the default settings of the system logging by changing the severity level and the storage location. The default is to log all messages up to debug level, that is, all system messages. By changing the severity level in the logging commands, you control the number of system messages logged. To specify the system logging settings, use the following commands.
Console logging: level Debugging Monitor logging: level Debugging Buffer logging: level Debugging, 40 Messages Logged, Size (40960 bytes) Trap logging: level Informational %IRC-6-IRC_COMMUP: Link to peer RPM is up %RAM-6-RAM_TASK: RPM1 is transitioning to Primary RPM.
– mail (for mail system messages) – news (for USENET news messages) – sys9 (system use) – sys10 (system use) – sys11 (system use) – sys12 (system use) – sys13 (system use) – sys14 (system use) – syslog (for syslog messages) – user (for user programs) – uucp (UNIX to UNIX copy protocol) Example of the show running-config logging Command To view nondefault settings, use the show running-config logging command in EXEC mode.
To view the logging synchronous configuration, use the show config command in LINE mode. Enabling Timestamp on Syslog Messages By default, syslog messages do not include a time/date stamp stating when the error or message was created. To enable timestamp, use the following command. • Add timestamp to syslog messages.
ftp-server enable Example of Viewing FTP Configuration Dell#show running ftp ! ftp-server enable ftp-server username nairobi password 0 zanzibar Dell# Configuring FTP Server Parameters After you enable the FTP server on the system, you can configure different parameters. To specify the system logging settings, use the following commands. • Specify the directory for users using FTP to reach the system. CONFIGURATION mode ftp-server topdir dir • The default is the internal flash directory.
To view the FTP configuration, use the show running-config ftp command in EXEC privilege mode, as shown in the example for Enable FTP Server. Terminal Lines You can access the system remotely and restrict access to the system by creating user profiles. Terminal lines on the system provide different means of accessing the system. The console line (console) connects you through the console port in the route processor modules (RPMs). The virtual terminal lines (VTYs) connect you through Telnet to the system.
seq 15 permit ip any any ! ipv6 access-list testv6deny seq 10 deny ipv6 3001::/64 any seq 15 permit ipv6 any any ! Dell(conf)# Dell(conf)#line vty 0 0 Dell(config-line-vty)#access-class testv6deny ipv6 Dell(config-line-vty)#access-class testvpermit ipv4 Dell(config-line-vty)#show c line vty 0 exec-timeout 0 0 access-class testpermit ipv4 access-class testv6deny ipv6 ! Dell Networking OS Behavior: Prior to Dell Networking OS version 7.4.2.
Dell(conf)#aaa authentication login myvtymethodlist line Dell(conf)#line vty 0 2 Dell(config-line-vty)#login authentication myvtymethodlist Dell(config-line-vty)#password myvtypassword Dell(config-line-vty)#show config line vty 0 password myvtypassword login authentication myvtymethodlist line vty 1 password myvtypassword login authentication myvtymethodlist line vty 2 password myvtypassword login authentication myvtymethodlist Dell(config-line-vty)# Setting Time Out of EXEC Privilege Mode EXEC time-out is
If you do not enter an IP address, Dell Networking OS enters a Telnet dialog that prompts you for one. Enter an IPv4 address in dotted decimal format (A.B.C.D). Enter an IPv6 address in the format 0000:0000:0000:0000:0000:0000:0000:0000. Elision of zeros is supported. Example of the telnet Command for Device Access Dell# telnet 10.11.80.203 Trying 10.11.80.203... Connected to 10.11.80.203. Exit character is '^]'.
If any user is already in CONFIGURATION mode when while a lock is in place, the following appears on their terminal (message 2): % Error: Can't lock configuration mode exclusively since the following users are currently configuring the system: User "admin" on line vty1 ( 10.1.1.1 ). NOTE: The CONFIGURATION mode lock corresponds to a VTY session, not a user.
When you use the Network boot procedure to boot the device, the boot loader checks if the primary partition contains a valid image. If a valid image exists on the primary partition and the secondary partition does not contain a valid image, then the primary boot line is set to A: and the secondary and default boot lines are set to a Null string.
5. Assign an IP address as the default gateway for the system. default-gateway gateway_ip_address For example, 10.16.150.254. 6. The environment variables are auto saved. 7. Reload the system.
5 802.1X 802.1X is a method of port security. A device connected to a port that is enabled with 802.1X is disallowed from sending or receiving packets on the network until its identity can be verified (through a username and password, for example). This feature is named for its IEEE specification. 802.
Figure 3. EAP Frames Encapsulated in Ethernet and RADUIS The authentication process involves three devices: • The device attempting to access the network is the supplicant. The supplicant is not allowed to communicate on the network until the authenticator authorizes the port. It can only communicate with the authenticator in response to 802.1X requests. • The device with which the supplicant communicates is the authenticator. The authenticator is the gate keeper of the network.
6. If the identity information provided by the supplicant is valid, the authentication server sends an Access-Accept frame in which network privileges are specified. The authenticator changes the port state to authorized and forwards an EAP Success frame. If the identity information is invalid, the server sends an Access-Reject frame. If the port state remains unauthorized, the authenticator forwards an EAP Failure frame. Figure 4. EAP Port-Authentication EAP over RADIUS 802.
RADIUS Attributes for 802.1 Support Dell Networking systems include the following RADIUS attributes in all 802.1X-triggered Access-Request messages: Attribute 31 Calling-station-id: relays the supplicant MAC address to the authentication server. Attribute 41 NAS-Port-Type: NAS-port physical port type. 15 indicates Ethernet. Attribute 61 NAS-Port: the physical port number by which the authenticator is connected to the supplicant.
Enabling 802.1X Enable 802.1X globally. Figure 6. 802.1X Enabled 1. Enable 802.1X globally. CONFIGURATION mode dot1x authentication 2. Enter INTERFACE mode on an interface or a range of interfaces. INTERFACE mode interface [range] 3. Enable 802.1X on the supplicant interface only. INTERFACE mode dot1x authentication Examples of Verifying that 802.1X is Enabled Globally and on an Interface Verify that 802.
In the following example, the bold lines show that 802.1X is enabled. Dell#show running-config | find dot1x dot1x authentication ! [output omitted] ! interface TenGigabitEthernet 2/1 no ip address dot1x authentication no shutdown ! Dell# To view 802.1X configuration information for an interface, use the show dot1x interface command. In the following example, the bold lines show that 802.1X is enabled on all ports unauthorized by default. Dell#show dot1x interface TenGigabitEthernet 2/1/ 802.
• Configure a maximum number of times the authenticator re-transmits a Request Identity frame. INTERFACE mode dot1x max-eap-req number The range is from 1 to 10. The default is 2. The example in Configuring a Quiet Period after a Failed Authentication shows configuration information for a port for which the authenticator re-transmits an EAP Request Identity frame after 90 seconds and re-transmits a maximum of 10 times.
Forcibly Authorizing or Unauthorizing a Port IEEE 802.1X requires that a port can be manually placed into any of three states: • ForceAuthorized — an authorized state. A device connected to this port in this state is never subjected to the authentication process, but is allowed to communicate on the network. Placing the port in this state is same as disabling 802.1X on the port. • ForceUnauthorized — an unauthorized state.
INTERFACE mode dot1x reauthentication [interval] seconds The range is from 1 to 65535. • The default is 3600. Configure the maximum number of times that the supplicant can be re-authenticated. INTERFACE mode dot1x reauth-max number The range is from 1 to 10. The default is 2. Example of Re-Authenticating a Port and Verifying the Configuration The bold lines show that re-authentication is enabled and the new maximum and re-authentication time period.
dot1x server-timeout seconds The range is from 1 to 300. The default is 30. Example of Viewing Configured Server Timeouts The example shows configuration information for a port for which the authenticator terminates the authentication process for an unresponsive supplicant or server after 15 seconds. The bold lines show the new supplicant and server timeouts. Dell(conf-if-Te-1/1)#dot1x port-control force-authorized Dell(conf-if-Te-1/1)#do show dot1x interface TenGigabitEthernet 1/1 802.
Figure 7. Dynamic VLAN Assignment 1. Configure 8021.x globally (refer to Enabling 802.1X) along with relevant RADIUS server configurations (refer to the illustration inDynamic VLAN Assignment with Port Authentication). 2. Make the interface a switchport so that it can be assigned to a VLAN. 3. Create the VLAN to which the interface will be assigned. 4. Connect the supplicant to the port configured for 802.1X. 5.
• If the supplicant fails authentication a specified number of times, the authenticator places the port in the Authentication-fail VLAN. • If a port is already forwarding on the Guest VLAN when 802.1X is enabled, the port is moved out of the Guest VLAN and the authentication process begins. Configuring a Guest VLAN If the supplicant does not respond within a determined amount of time ([reauth-max + 1] * tx-period, the system assumes that the host does not have 802.
Example of Viewing Configured Authentication View your configuration using the show config command from INTERFACE mode, as shown in the example in Configuring a Guest VLAN or using the show dot1x interface command from EXEC Privilege mode. 802.
6 Access Control Lists (ACLs) This chapter describes access control lists (ACLs), prefix lists, and route-maps. At their simplest, access control lists (ACLs), prefix lists, and route-maps permit or deny traffic based on MAC and/or IP addresses. This chapter describes implementing IP ACLs, IP prefix lists and route-maps. For MAC ACLS, refer to Layer 2.
NOTE: You can configure VRF-aware ACLs on interfaces either using a range of VLANs or a range of VRFs but not both. IP Access Control Lists (ACLs) In Dell Networking switch/routers, you can create two different types of IP ACLs: standard or extended. A standard ACL filters packets based on the source IP packet.
CAM Optimization When you enable this command, if a policy map containing classification rules (ACL and/or dscp/ ip-precedence rules) is applied to more than one physical interface on the same port-pipe, only a single copy of the policy is written (only one FP entry is used). When you disable this command, the system behaves as described in this chapter. Test CAM Usage This command applies to both IPv4 and IPv6 CAM profiles, but is best used when verifying QoS optimization for IPv6 ACLs.
Determine the Order in which ACLs are Used to Classify Traffic When you link class-maps to queues using the service-queue command, Dell Networking OS matches the class-maps according to queue priority (queue numbers closer to 0 have lower priorities). As shown in the following example, class-map cmap2 is matched against ingress packets before cmap1. ACLs acl1 and acl2 have overlapping rules because the address range 20.1.1.0/24 is within 20.0.0.0/8.
• Configure a route map for route tagging (optional) Creating a Route Map Route maps, ACLs, and prefix lists are similar in composition because all three contain filters, but route map filters do not contain the permit and deny actions found in ACLs and prefix lists. Route map filters match certain routes and set or specify values. To create a route map, use the following command. • Create a route map and assign it a unique name. The optional permit and deny keywords are the action of the route map.
The following example shows a route map with multiple instances. The show config command displays only the configuration of the current route map instance. To view all instances of a specific route map, use the show route-map command.
Configuring Match Routes To configure match criterion for a route map, use the following commands. • Match routes with the same AS-PATH numbers. CONFIG-ROUTE-MAP mode • match as-path as-path-name Match routes with COMMUNITY list attributes in their path. CONFIG-ROUTE-MAP mode • match community community-list-name [exact] Match routes whose next hop is a specific interface.
match origin {egp | igp | incomplete} • Match routes specified as internal or external to OSPF, ISIS level-1, ISIS level-2, or locally generated. CONFIG-ROUTE-MAP mode match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local } • Match routes with a specific tag. CONFIG-ROUTE-MAP mode match tag tag-value To create route map instances, use these commands.
CONFIG-ROUTE-MAP mode set tag tag-value • Specify a value as the route’s weight. CONFIG-ROUTE-MAP mode set weight value To create route map instances, use these commands. There is no limit to the number of set commands per route map, but the convention is to keep the number of set filters in a route map low. Set commands do not require a corresponding match command.
! set tag 34 Continue Clause Normally, when a match is found, set clauses are executed, and the packet is then forwarded; no more route-map modules are processed. If you configure the continue command at the end of a module, the next module (or a specified module) is processed even after a match is found. The following example shows a continue clause at the end of a route-map module. In this example, if a match is found in the route-map “test” module 10, module 30 is processed.
Dell(conf-ext-nacl)#permit ip any 10.1.1.1/32 Dell(conf-ext-nacl) Layer 4 ACL Rules Examples The following examples show the ACL commands for Layer 4 packet filtering. Permit an ACL line with L3 information only, and the fragments keyword is present: If a packet’s L3 information matches the L3 information in the ACL line, the packet's FO is checked. • If a packet's FO > 0, the packet is permitted. • If a packet's FO = 0, the next ACL entry is processed.
A standard IP ACL uses the source IP address as its match criterion. 1. Enter IP ACCESS LIST mode by naming a standard IP access list. CONFIGURATION mode ip access-list standard access-listname 2. Configure a drop or forward filter. CONFIG-STD-NACL mode seq sequence-number {deny | permit} {source [mask] | any | host ip-address} [count [byte] [dscp] [order] [fragments] NOTE: When assigning sequence numbers to filters, keep in mind that you might need to insert a new filter.
ip access-list standard access-list-name 2. Configure a drop or forward IP ACL filter. CONFIG-STD-NACL mode {deny | permit} {source [mask] | any | host ip-address} [count [byte] [dscp] [order] [fragments] When you use the log keyword, the CP logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
CONFIG-EXT-NACL mode seq sequence-number {deny | permit} {ip-protocol-number | icmp | ip | tcp | udp} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator port [port]] [count [byte]] [order] [fragments] When you use the log keyword, the CP logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
Configuring Filters Without a Sequence Number If you are creating an extended ACL with only one or two filters, you can let Dell Networking OS assign a sequence number based on the order in which the filters are configured. Dell Networking OS assigns filters in multiples of five. To configure a filter for an extended IP ACL without a specified sequence number, use any or all of the following commands: • Configure a deny or permit filter to examine IP packets.
• L2 egress access list If a rule is simply appended, existing counters are not affected. Table 6. L2 and L3 Filtering on Switched Packets L2 ACL Behavior L3 ACL Behavior Decision on Targeted Traffic Deny Deny L3 ACL denies. Deny Permit L3 ACL permits. Permit Deny L3 ACL denies. Permit Permit L3 ACL permits. NOTE: If you configure an interface as a vlan-stack access port, only the L2 ACL filters the packets. The L3 ACL applied to such a port does not affect traffic.
4. Apply rules to the new ACL. INTERFACE mode ip access-list [standard | extended] name To view which IP ACL is applied to an interface, use the show config command in INTERFACE mode, or use the show running-config command in EXEC mode. Example of Viewing ACLs Applied to an Interface Dell(conf-if)#show conf ! interface TenGigabitEthernet 1/1 ip address 10.2.1.100 255.255.255.
Extended Ingress IP access list abcd on tengigabitethernet 1/1 seq 5 permit tcp any any seq 10 deny icmp any any seq 15 permit 1.1.1.
seq 5 permit tcp any any seq 10 deny icmp any any seq 15 permit 1.1.1.2 Dell#configure terminal Dell(conf)#interface te 1/2 Dell(conf-if-te-1/2)#ip vrf forwarding blue Dell(conf-if-te-1/2)#show config ! interface TenGigabitEthernet 1/2 ip vrf forwarding blue no ip address shutdown Dell(conf-if-te-1/2)# Dell(conf-if-te-1/2)# Dell(conf-if-te-1/2)#end Dell# Applying Egress Layer 3 ACLs (Control-Plane) By default, packets originated from the system are not filtered by egress ACLs.
• To permit routes with the mask greater than /8 but less than /12, enter permit x.x.x.x/x ge 8. • To deny routes with a mask less than /24, enter deny x.x.x.x/x le 24. • To permit routes with a mask greater than /20, enter permit x.x.x.x/x ge 20. The following rules apply to prefix lists: • A prefix list without any permit or deny filters allows all routes.
The following example shows how the seq command orders the filters according to the sequence number assigned. In the example, filter 20 was configured before filter 15 and 12, but the show config command displays the filters in the correct order. Dell(conf-nprefixl)#seq 20 permit 0.0.0.0/0 le 32 Dell(conf-nprefixl)#seq 12 deny 134.23.0.0 /16 Dell(conf-nprefixl)#seq 15 deny 120.23.14.0 /8 le 16 Dell(conf-nprefixl)#show config ! ip prefix-list juba seq 12 deny 134.23.0.0/16 seq 15 deny 120.0.0.
EXEC Privilege mode show ip prefix-list detail [prefix-name] • Show a table of summarized information about configured Prefix lists. EXEC Privilege mode show ip prefix-list summary [prefix-name] Examples of the show ip prefix-list detail and show ip prefix-list summary Commands The following example shows the show ip prefix-list detail command.
Example of Viewing Configured Prefix Lists (ROUTER RIP mode) To view the configuration, use the show config command in ROUTER RIP mode, or the show running-config rip command in EXEC mode. Dell(conf-router_rip)#show config ! router rip distribute-list prefix juba out network 10.0.0.0 Dell(conf-router_rip)#router ospf 34 Applying a Filter to a Prefix List (OSPF) To apply a filter to routes in open shortest path first (OSPF), use the following commands. • Enter OSPF mode.
Table 7. ACL Resequencing Rules Resquencing Rules Before Resequencing: seq 5 permit any host 1.1.1.1 seq 6 permit any host 1.1.1.2 seq 7 permit any host 1.1.1.3 seq 10 permit any host 1.1.1.4 Rules After Resequencing: seq 5 permit any host 1.1.1.1 seq 10 permit any host 1.1.1.2 seq 15 permit any host 1.1.1.3 seq 20 permit any host 1.1.1.4 Resequencing an ACL or Prefix List Resequencing is available for IPv4 and IPv6 ACLs, prefix lists, and MAC ACLs.
Remarks that do not have a corresponding rule are incremented as a rule. These two mechanisms allow remarks to retain their original position in the list. The following example shows remark 10 corresponding to rule 10 and as such, they have the same number before and after the command is entered. Remark 4 is incremented as a rule, and all rules have retained their original positions.
When a stack unit is reset or a stack unit undergoes a failure, the ACL agent registers with the port mirroring application. The port mirroring utility downloads the monitoring configuration to the ACL agent. The interface manager notifies the port mirroring application about the removal of an interface when an ACL entry associated with that interface to is deleted.
Example Output of the show Command Dell# show ip accounting access-list ! Extended Ingress IP access list kar on TenGigabitEthernet 1/1 Total cam count 1 seq 5 permit ip 192.168.20.0/24 173.168.20.0/24 monitor Dell#show ipv6 accounting access-list ! Ingress IPv6 access list kar on TenGigabitEthernet 1/1 Total cam count 1 seq 5 permit ipv6 22::/24 33::/24 monitor Enabling Flow-Based Monitoring Flow-based monitoring is supported on the S6000 platform.
seq 10 permit ip 102.1.1.0/24 any monitor count bytes (0 packets 0 bytes) seq 15 deny udp any any count bytes (0 packets 0 bytes) seq 20 deny tcp any any count bytes (0 packets 0 bytes) Dell(conf)#do show monitor session 0 ct-maa-s4820-2(conf-mon-sess-0)#do show monitor session 0 SessID -----0 Source -----Te 1/1 Destination ----------Te 1/2 Dir --rx Mode Source IP ---- --------Flow N/A Dest IP -------N/A Configuring UDF ACL To configure UDF ACL, use the following commands. 1.
L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : L2PT : IpMacAcl : VmanQos : EcfmAcl : FcoeAcl : iscsiOptAcl : ipv4pbr : vrfv4Acl : Openflow : fedgovacl : nlbclusteracl: 2 2 0 2 1 0 0 0 2 4 0 0 0 0 0 0 1 8(UdfEnabled) 2 0 2 0 0 0 0 0 0 0 0 0 0 0 Dell# 4. Create a context for UDF TCAM. CONFIGURATION mode udf-tcam name seq number Dell(conf)#udf-tcam ipnip seq 1 5. Configure UDF data context for parsing the different header location offset and required bytes.
udf-qualifier-value name Dell(conf-udf-tcam)# udf-qualifier-value ipnip_val1 10. Assign value for each configured UDF ID in the given UDF TCAM profile. CONFIGURATION-UDF-Qualifier-Value Profile mode udf-id 1-12 value mask Dell(conf-udf-tcam-qual-val)#udf-id 1 aa ff 11. Associate the UDF in IP access-list.
7 Bidirectional Forwarding Detection (BFD) BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no routing protocol is used. BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake.
BFD Packet Format Control packets are encapsulated in user datagram protocol (UDP) packets. The following illustration shows the complete encapsulation of a BFD control packet inside an IPv4 packet. Figure 8. BFD in IPv4 Packet Format Field Description Diagnostic Code The reason that the last session failed. State The current local session state. Refer to BFD Sessions. Flag A bit that indicates packet function.
Field Description My Discriminator A random number generated by the local system to identify the session. Your Discriminator A random number generated by the remote system to identify the session. Discriminator values are necessary to identify the session to which a control packet belongs because there can be many sessions running on a single interface. Desired Min TX Interval The minimum rate at which the local system would like to send control packets to the remote system.
Administratively Down The local system does not participate in a particular session. Down The remote system is not sending control packets or at least not within the detection time for a particular session. Init The local system is communicating. Up Both systems are exchanging control packets. The session is declared down if: • A control packet is not received within the detection time. • Sufficient echo packets are lost.
Figure 9.
Session State Changes The following illustration shows how the session state on a system changes based on the status notification it receives from the remote system. For example, if a session on a system is down and it receives a Down status notification from the remote system, the session state on the local system changes to Init. Figure 10. Session State Changes Important Points to Remember • • Enable BFD on both ends of a link. • Demand mode, authentication, and the Echo function are not supported.
• Configure BFD for VRRP • Configuring Protocol Liveness • Troubleshooting BFD Configure BFD for Physical Ports Configuring BFD for physical ports is supported on the C-Series and E-Series platforms only. BFD on physical ports is useful when you do not enable the routing protocol. Without BFD, if the remote system fails, the local system does not remove the connected route until the first failed attempt to send a packet.
Establishing a Session on Physical Ports To establish a session, enable BFD at the interface level on both ends of the link, as shown in the following illustration. The configuration parameters do not need to match. Figure 11. Establishing a BFD Session on Physical Ports 1. Enter interface mode. CONFIGURATION mode interface 2. Assign an IP address to the interface if one is not already assigned. INTERFACE mode ip address ip-address 3.
Neighbor parameters: TX: 100ms, RX: 100ms, Multiplier: 3 Actual parameters: TX: 100ms, RX: 100ms, Multiplier: 3 Role: Active Delete session on Down: False Client Registered: CLI Uptime: 00:03:57 Statistics: Number of packets received from neighbor: 1775 Number of packets sent to neighbor: 1775 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Log messages display when you configure both interfaces for BFD.
• Disable BFD on an interface. INTERFACE mode no bfd enable • Enable BFD on an interface. INTERFACE mode bfd enable If you disable BFD on a local interface, this message displays: R1(conf-if-te-4/24)#01:00:52: %RPM0-P:RP2 %BFDMGR-1-BFD_STATE_CHANGE: Changed session state to Ad Dn for neighbor 2.2.2.
ip route bfd Example of the show bfd neighbors Command to Verify Static Routes To verify that sessions have been created for static routes, use the show bfd neighbors command. R1(conf)#ip route 2.2.3.0/24 2.2.2.2 R1(conf)#ip route bfd R1(conf)#do show bfd neighbors * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 2.2.2.
Related Configuration Tasks • Changing OSPF Session Parameters • Disabling BFD for OSPF Establishing Sessions with OSPF Neighbors BFD sessions can be established with all OSPF neighbors at once or sessions can be established with all neighbors out of a specific interface. Sessions are only established when the OSPF adjacency is in the Full state. Figure 13.
Example of Verifying Sessions with OSPF Neighbors To view the established sessions, use the show bfd neighbors command. The bold line shows the OSPF BFD sessions. R2(conf-router_ospf)#bfd all-neighbors R2(conf-router_ospf)#do show bfd neighbors * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr * 2.2.2.2 * 2.2.3.1 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 Te 2/1 Up 100 100 3 O 2.2.3.
Configuring BFD for OSPFv3 is a two-step process: 1. Enable BFD globally. 2. Establish sessions with OSPFv3 neighbors. Related Configuration Tasks • Changing OSPFv3 Session Parameters • Disabling BFD for OSPFv3 Establishing Sessions with OSPFv3 Neighbors You can establish BFD sessions with all OSPFv3 neighbors at once or with all neighbors out of a specific interface. Sessions are only established when the OSPFv3 adjacency is in the Full state.
• no bfd all-neighbors Disable BFD sessions with OSPFv3 neighbors on a single interface. INTERFACE mode ipv6 ospf bfd all-neighbors disable Configure BFD for IS-IS When using BFD with IS-IS, the IS-IS protocol registers with the BFD manager on the RPM. BFD sessions are then established with all neighboring interfaces participating in IS-IS. If a neighboring interface fails, the BFD agent on the line card notifies the BFD manager, which in turn notifies the IS-IS protocol that a link state change occurred.
• Establish sessions with all IS-IS neighbors. ROUTER-ISIS mode bfd all-neighbors • Establish sessions with IS-IS neighbors on a single interface. INTERFACE mode isis bfd all-neighbors Example of Verifying Sessions with IS-IS Neighbors To view the established sessions, use the show bfd neighbors command. The bold line shows that IS-IS BFD sessions are enabled.
no bfd all-neighbors • Disable BFD sessions with IS-IS neighbors on a single interface. INTERFACE mose isis bfd all-neighbors disable Configure BFD for BGP In a BGP core network, BFD provides rapid detection of communication failures in BGP fast-forwarding paths between internal BGP (iBGP) and external BGP (eBGP) peers for faster network reconvergence. BFD for BGP is supported on 1GE, 10GE, 40GE, portchannel, and VLAN interfaces. BFD for BGP does not support IPv6 and the BGP multihop feature.
• By establishing BFD sessions with all neighbors discovered by BGP (the bfd all-neighbors command). • By establishing a BFD session with a specified BGP neighbor (the neighbor {ip-address | peer-group-name} bfd command) BFD packets originating from a router are assigned to the highest priority egress queue to minimize transmission delays.
Disabling BFD for BGP You can disable BFD for BGP. To disable a BFD for BGP session with a specified neighbor, use the first command. To remove the disabled state of a BFD for BGP session with a specified neighbor, use the second command. The BGP link with the neighbor returns to normal operation and uses the BFD session parameters globally configured with the bfd all-neighbors command or configured for the peer group to which the neighbor belongs. • Disable a BFD for BGP session with a specified neighbor.
• Displays routing information exchanged with BGP neighbors, including BFD for BGP sessions. EXEC Privilege mode show ip bgp neighbors [ip-address] Examples of the BFD show Commands The following example shows verifying a BGP configuration. R2# show running-config bgp ! router bgp 2 neighbor 1.1.1.2 remote-as 1 neighbor 1.1.1.2 no shutdown neighbor 2.2.2.2 remote-as 1 neighbor 2.2.2.2 no shutdown neighbor 3.3.3.2 remote-as 1 neighbor 3.3.3.
Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 5 Session Discriminator: 10 Neighbor Discriminator: 11 Local Addr: 2.2.2.3 Local MAC Addr: 00:01:e8:66:da:34 Remote Addr: 2.2.2.
The bold line shows the message displayed when you enable BFD for BGP connections. R2# show ip bgp summary BGP router identifier 10.0.0.1, local AS number 2 BGP table version is 0, main routing table version 0 BFD is enabled, Interval 100 Min_rx 100 Multiplier 3 Role Active 3 neighbor(s) using 24168 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 1.1.1.2 2.2.2.2 3.3.3.
BGP state ESTABLISHED, in this state for 00:05:33 ... Neighbor is using BGP neighbor mode BFD configuration Peer active in peer-group outbound optimization ... R2# show ip bgp neighbors 2.2.2.4 BGP neighbor is 2.2.2.4, remote AS 1, external link Member of peer-group pg1 for session parameters BGP version 4, remote router ID 12.0.0.4 BGP state ESTABLISHED, in this state for 00:05:33 ... Neighbor is using BGP peer-group mode BFD configuration Peer active in peer-group outbound optimization ...
Establishing Sessions with All VRRP Neighbors BFD sessions can be established for all VRRP neighbors at once, or a session can be established with a particular neighbor. Figure 16. Establishing Sessions with All VRRP Neighbors To establish sessions with all VRRP neighbors, use the following command. • Establish sessions with all VRRP neighbors.
I O R V - ISIS OSPF Static Route (RTM) VRRP LocalAddr * 2.2.5.1 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.5.2 Te 4/25 Down 1000 1000 3 V To view session state information, use the show vrrp command. The bold line shows the VRRP BFD session. Dell(conf-if-te-4/25)#do show vrrp -----------------TenGigabitEthernet 4/1, VRID: 1, Net: 2.2.5.1 State: Backup, Priority: 1, Master: 2.2.5.
Disabling BFD for VRRP If you disable any or all VRRP sessions, the sessions are torn down. A final Admin Down control packet is sent to all neighbors and sessions on the remote system change to the Down state. To disable all VRRP sessions on an interface, sessions for a particular VRRP group, or for a particular VRRP session on an interface, use the following commands. • Disable all VRRP sessions on an interface. INTERFACE mode • no vrrp bfd all-neighbors Disable all VRRP sessions in a VRRP group.
Version:1, Diag code:0, State:Init, Poll bit:0, Final bit:0, Demand bit:0 myDiscrim:6, yourDiscrim:4, minTx:1000000, minRx:1000000, multiplier:3, minEchoRx:0 00:54:38: %RPM0-P:RP2 %BFDMGR-1-BFD_STATE_CHANGE: Changed session state to Up for neighbor 2.2.2.2 on interface Te 4/24 (diag: 0) The following example shows hexadecimal output from the debug bfd packet command. RX packet dump: 20 c0 03 18 00 00 00 05 00 00 00 04 00 01 86 a0 00 01 86 a0 00 00 00 00 00:34:13 : Sent packet for session with neighbor 2.2.
8 Border Gateway Protocol IPv4 (BGPv4) This chapter provides a general description of BGPv4 as it is supported in the Dell Networking Operating System (OS). BGP protocol standards are listed in the Standards Compliance chapter. BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). The primary function of the BGP is to exchange network reachability information with other BGP systems.
Figure 17. Internal BGP BGP version 4 (BGPv4) supports classless interdomain routing and aggregate routes and AS paths. BGP is a path vector protocol — a computer network in which BGP maintains the path that updated information takes as it diffuses through the network. Updates traveling through the network and returning to the same node are easily detected and discarded.
Figure 18. BGP Routers in Full Mesh The number of BGP speakers each BGP peer must maintain increases exponentially. Network management quickly becomes impossible. Sessions and Peers When two routers communicate using the BGP protocol, a BGP session is started. The two end-points of that session are Peers. A Peer is also called a Neighbor. Establish a Session Information exchange between peers is driven by events and timers. The focus in BGP is on the traffic routing policies.
State Description Idle BGP initializes all resources, refuses all inbound BGP connection attempts, and initiates a TCP connection to the peer. Connect In this state the router waits for the TCP connection to complete, transitioning to the OpenSent state if successful. If that transition is not successful, BGP resets the ConnectRetry timer and transitions to the Active state when the timer expires. Active The router resets the ConnectRetry timer to zero and returns to the Connect state.
Figure 19. BGP Router Rules 1. Router B receives an advertisement from Router A through eBGP. Because the route is learned through eBGP, Router B advertises it to all its iBGP peers: Routers C and D. 2. Router C receives the advertisement but does not advertise it to any peer because its only other peer is Router D, an iBGP peer, and Router D has already learned it through iBGP from Router B. 3.
reduce the options. If a number of best paths is determined, this selection criteria is applied to group’s best to determine the ultimate best path. In non-deterministic mode (the bgp non-deterministic-med command is applied), paths are compared in the order in which they arrive. This method can lead to Dell Networking OS choosing different best paths from a set of paths, depending on the order in which they were received from the neighbors because MED may or may not get compared between the adjacent paths.
b. A path with no AS_PATH configured has a path length of 0. c. AS_CONFED_SET is not included in the AS_PATH length. d. AS_CONFED_SEQUENCE has a path length of 1, no matter how many ASs are in the AS_CONFED_SEQUENCE. 5. Prefer the path with the lowest ORIGIN type (IGP is lower than EGP, and EGP is lower than INCOMPLETE). 6. Prefer the path with the lowest multi-exit discriminator (MED) attribute. The following criteria apply: a.
Figure 21. BGP Local Preference Multi-Exit Discriminators (MEDs) If two ASs connect in more than one place, a multi-exit discriminator (MED) can be used to assign a preference to a preferred path. MED is one of the criteria used to determine the best path, so keep in mind that other criteria may impact selection, as shown in the illustration in Best Path Selection Criteria. One AS assigns the MED a value and the other AS uses that value to decide the preferred path.
Figure 22. Multi-Exit Discriminators NOTE: Configuring the set metric-type internal command in a route-map advertises the IGP cost as MED to outbound EBGP peers when redistributing routes. The configured set metric value overwrites the default IGP cost. If the outbound route-map uses MED, it overwrites IGP MED. Origin The origin indicates the origin of the prefix, or how the prefix came into BGP. There are three origin codes: IGP, EGP, INCOMPLETE.
NOTE: Any update that contains the AS path number 0 is valid. The AS path is shown in the following example. The origin attribute is shown following the AS path information (shown in bold).
Implement BGP with Dell Networking OS The following sections describe how to implement BGP on Dell Networking OS. Additional Path (Add-Path) Support The add-path feature reduces convergence times by advertising multiple paths to its peers for the same address prefix without replacing existing paths with new ones. By default, a BGP speaker advertises only the best path to its peers for a given address prefix.
Ignore Router-ID for Some Best-Path Calculations Dell Networking OS allows you to avoid unnecessary BGP best-path transitions between external paths under certain conditions. The bgp bestpath router-id ignore command reduces network disruption caused by routing and forwarding plane changes and allows for faster convergence. Four-Byte AS Numbers Dell Networking OS supports 4-Byte (32-bit) format when configuring autonomous system numbers (ASNs).
Dynamic AS Number Notation Application Dell Networking OS applies the ASN notation type change dynamically to the running-config statements. When you apply or change an asnotation, the type selected is reflected immediately in the running-configuration and the show commands (refer to the following two examples).
Dell(conf-router_bgp)#do show ip bgp BGP table version is 28093, local router ID is 172.30.1.57 AS Number Migration With this feature you can transparently change the AS number of an entire BGP network and ensure that the routes are propagated throughout the network while the migration is in progress. When migrating one AS to another, perhaps combining ASs, an eBGP network may lose its routing to an iBGP if the ASN changes.
If you use the “no prepend” option, the Local-AS does not prepend to the updates received from the eBGP peer. If you do not select “no prepend” (the default), the Local-AS is added to the first AS segment in the AS-PATH. If an inbound route-map is used to prepend the as-path to the update from the peer, the Local-AS is added first. For example, consider the topology described in the previous illustration.
• To avoid SNMP timeouts with a large-scale configuration (large number of BGP neighbors and a large BGP Loc-RIB), Dell Networking recommends setting the timeout and retry count values to a relatively higher number. For example, t = 60 or r = 5. • To return all values on an snmpwalk for the f10BgpM2Peer sub-OID, use the -C c option, such as snmpwalk -v 2c -C c c public. • An SNMP walk may terminate pre-maturely if the index does not increment lexicographically.
Item Default Graceful Restart feature Disabled Local preference 100 MED 0 Route Flap Damping Parameters half-life = 15 minutes reuse = 750 suppress = 2000 max-suppress-time = 60 minutes external distance = 20 Distance internal distance = 200 local distance = 200 keepalive = 60 seconds Timers holdtime = 180 seconds Add-path Disabled Enabling BGP By default, BGP is not enabled on the system. Dell Networking OS supports one autonomous system (AS) and assigns the AS number (ASN).
CONFIG-ROUTER-BGP mode bgp four-octet-as-support NOTE: Use it only if you support 4-Byte AS numbers or if you support AS4 number representation. If you are supporting 4-Byte ASNs, enable this command. Disable 4-Byte support and return to the default 2-Byte format by using the no bgp four-octet-as-support command. You cannot disable 4-Byte support if you currently have a 4-Byte ASN configured. Disabling 4-Byte AS numbers also disables ASDOT and ASDOT+ number representation.
100.10.92.9 65192 0 192.168.10.1 65123 0 192.168.12.2 65123 0 R2# 0 0 0 0 0 0 0 0 0 0 never 0 never 0 never Active Active Active The following example shows the show ip bgp summary command output (4–byte AS number displays). R2#show ip bgp summary BGP router identifier 192.168.10.2, local AS number 48735.
Local host: 10.114.8.39, Local port: 1037 Foreign host: 10.114.8.60, Foreign port: 179 BGP neighbor is 10.1.1.1, remote AS 65535, internal link Administratively shut down BGP version 4, remote router ID 10.0.0.
Only one form of AS number representation is supported at a time. You cannot combine the types of representations within an AS. To configure AS4 number representations, use the following commands. • Enable ASPLAIN AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asplain NOTE: ASPLAIN is the default method Dell Networking OS uses and does not appear in the configuration display. • Enable ASDOT AS Number representation.
Configuring Peer Groups To configure multiple BGP neighbors at one time, create and populate a BGP peer group. An advantage of peer groups is that members of a peer group inherit the configuration properties of the group and share same update policy. A maximum of 256 peer groups are allowed on the system. Create a peer group by assigning it a name, then adding members to the peer group. After you create a peer group, you can configure route policies for it.
When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
Peer-group zanzibar, remote AS 65535 BGP version 4 Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP neighbor is zanzibar, peer-group internal, Number of peers in this group 26 Peer-group members (* - outbound optimized): 10.68.160.1 10.68.161.1 10.68.162.1 10.68.163.1 10.68.164.1 10.68.165.1 10.68.166.1 10.68.167.1 10.68.168.1 10.68.169.1 10.68.170.1 10.68.171.1 10.68.172.1 10.68.173.1 10.68.174.1 10.68.175.1 10.68.176.1 10.68.177.1 10.68.178.1 10.68.179.1 10.68.180.
BGP neighbor is 100.100.100.100, remote AS 65517, internal link Member of peer-group test for session parameters BGP version 4, remote router ID 30.30.30.
neighbor 100.100.100.100 no shutdown Dell# Configuring Passive Peering When you enable a peer-group, the software sends an OPEN message to initiate a TCP connection. If you enable passive peering for the peer group, the software does not send an OPEN message, but it responds to an OPEN message. When a BGP neighbor connection with authentication configured is rejected by a passive peer-group, Dell Networking OS does not allow another passive peer-group on the same subnet to connect with the BGP neighbor.
Example of the Verifying that Local AS Numbering is Disabled The first line in bold shows the actual AS number. The second two lines in bold show the local AS number (6500) maintained during migration. To disable this feature, use the no neighbor local-as command in CONFIGURATION ROUTER BGP mode. R2(conf-router_bgp)#show conf ! router bgp 65123 bgp router-id 192.168.10.2 network 10.10.21.0/24 network 10.10.32.0/24 network 100.10.92.0/24 network 192.168.10.0/24 bgp four-octet-as-support neighbor 10.10.21.
network 192.168.10.0/24 bgp four-octet-as-support neighbor 10.10.21.1 remote-as 65123 neighbor 10.10.21.1 filter-list Laura in neighbor 10.10.21.1 no shutdown neighbor 10.10.32.3 remote-as 65123 neighbor 10.10.32.3 no shutdown neighbor 100.10.92.9 remote-as 65192 neighbor 100.10.92.9 local-as 6500 neighbor 100.10.92.9 no shutdown neighbor 192.168.10.1 remote-as 65123 neighbor 192.168.10.1 update-source Loopback 0 neighbor 192.168.10.1 no shutdown neighbor 192.168.12.2 remote-as 65123 neighbor 192.168.12.
bgp graceful-restart [stale-path-time time-in-seconds] • The default is 360 seconds. Local router supports graceful restart as a receiver only. CONFIG-ROUTER-BGP mode bgp graceful-restart [role receiver-only] Enabling Neighbor Graceful Restart BGP graceful restart is active only when the neighbor becomes established. Otherwise, it is disabled. Graceful-restart applies to all neighbors with established adjacency.
ip as-path access-list as-path-name 2. Enter the parameter to match BGP AS-PATH for filtering. CONFIG-AS-PATH mode {deny | permit} filter parameter This is the filter that is used to match the AS-path. The entries can be any format, letters, numbers, or regular expressions. You can enter this command multiple times if multiple filters are desired. For accepted expressions, refer to Regular Expressions as Filters. 3. Return to CONFIGURATION mode. AS-PATH ACL mode exit 4. Enter ROUTER BGP mode.
Regular Expressions as Filters Regular expressions are used to filter AS paths or community lists. A regular expression is a special character used to define a pattern that is then compared with an input string. For an AS-path access list, as shown in the previous commands, if the AS path matches the regular expression in the access list, the route matches the access list. The following lists the regular expressions accepted in Dell Networking OS.
Dell(config-as-path)#deny 32$ Dell(config-as-path)#ex Dell(conf)#router bgp 99 Dell(conf-router_bgp)#neighbor AAA filter-list Eagle in Dell(conf-router_bgp)#show conf ! router bgp 99 neighbor AAA peer-group neighbor AAA filter-list Eaglein neighbor AAA no shutdown neighbor 10.155.15.2 remote-as 32 neighbor 10.155.15.2 filter-list 1 in neighbor 10.155.15.
Enabling Additional Paths The add-path feature is disabled by default. NOTE: Dell Networking OS recommends not using multipath and add path simultaneously in a route reflector. To allow multiple paths sent to peers, use the following commands. 1. Allow the advertisement of multiple paths for the same address prefix without the new paths replacing any previous ones. CONFIG-ROUTER-BGP mode bgp add-path [both|received|send] path-count count The range is from 2 to 64. 2.
• • • no-export: routes with the COMMUNITY attribute of NO_EXPORT. quote-regexp: then any number of regular expressions. The software applies all regular expressions in the list. regexp: then a regular expression. Example of the show ip community-lists Command To view the configuration, use the show config command in CONFIGURATION COMMUNITY-LIST or CONFIGURATION EXTCOMMUNITY LIST mode or the show ip {community-lists | extcommunity-list} command in EXEC Privilege mode.
deny deny deny deny deny deny deny deny deny deny deny deny deny deny deny deny deny deny Dell# 701:20 702:20 703:20 704:20 705:20 14551:20 701:112 702:112 703:112 704:112 705:112 14551:112 701:667 702:667 703:667 704:666 705:666 14551:666 Filtering Routes with Community Lists To use an IP community list or IP extended community list to filter routes, you must apply a match community filter to a route map and then apply that route map to a BGP neighbor or peer group. 1.
To send the COMMUNITY attribute to BGP neighbors, use the following command. • Enable the software to send the router’s COMMUNITY attribute to the BGP neighbor or peer group specified. CONFIG-ROUTER-BGP mode neighbor {ip-address | peer-group-name} send-community To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode.
Origin codes: i - IGP, e - EGP, ? - incomplete Network * i 3.0.0.0/8 *>i 4.2.49.12/30 * i 4.21.132.0/23 *>i 4.24.118.16/30 *>i 4.24.145.0/30 *>i 4.24.187.12/30 *>i 4.24.202.0/30 *>i 4.25.88.0/30 *>i 6.1.0.0/16 *>i 6.2.0.0/22 *>i 6.3.0.0/18 *>i 6.4.0.0/16 *>i 6.5.0.0/19 *>i 6.8.0.0/20 *>i 6.9.0.0/20 *>i 6.10.0.0/15 *>i 6.14.0.0/15 *>i 6.133.0.0/21 *>i 6.151.0.0/16 --More-- Next Hop Metric 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.16 195.171.0.
A more flexible method for manipulating the LOCAL_PREF attribute value is to use a route map. 1. Enter the ROUTE-MAP mode and assign a name to a route map. CONFIGURATION mode route-map map-name [permit | deny] [sequence-number] 2. Change LOCAL_PREF value for routes meeting the criteria of this route map. CONFIG-ROUTE-MAP mode set local-preference value 3. Return to CONFIGURATION mode. CONFIG-ROUTE-MAP mode exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number 5.
• Sets weight for the route. CONFIG-ROUTE-MAP mode set weight weight – weight: the range is from 0 to 65535. To view BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show runningconfig bgp command in EXEC Privilege mode. Enabling Multipath By default, the software allows one path to a destination. You can enable multipath to allow up to 64 parallel paths to a destination.
• ge: minimum prefix length to be matched. • le: maximum prefix length to me matched. For information about configuring prefix lists, refer to Access Control Lists (ACLs). 3. Return to CONFIGURATION mode. CONFIG-PREFIX LIST mode exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number 5. Filter routes based on the criteria in the configured prefix list.
5. Filter routes based on the criteria in the configured route map. CONFIG-ROUTER-BGP mode neighbor {ip-address | peer-group-name} route-map map-name {in | out} Configure the following parameters: • ip-address or peer-group-name: enter the neighbor’s IP address or the peer group’s name. • map-name: enter the name of a configured route map. • in: apply the route map to inbound routes. • out: apply the route map to outbound routes.
With route reflection configured properly, IBGP routers are not fully meshed within a cluster but all receive routing information. Configure clusters of routers where one router is a concentration router and the others are clients who receive their updates from the concentration router. To configure a route reflector, use the following commands. • Assign an ID to a router reflector cluster. CONFIG-ROUTER-BGP mode bgp cluster-id cluster-id • You can have multiple clusters in an AS.
the confederations appear as one AS. Within the confederation sub-AS, the IBGP neighbors are fully meshed and the MED, NEXT_HOP, and LOCAL_PREF attributes are maintained between confederations. To configure BGP confederations, use the following commands. • Specifies the confederation ID. CONFIG-ROUTER-BGP mode bgp confederation identifier as-number – as-number: from 0 to 65535 (2 Byte) or from 1 to 4294967295 (4 Byte). • Specifies which confederation sub-AS are peers.
– half-life: the range is from 1 to 45. Number of minutes after which the Penalty is decreased. After the router assigns a Penalty of 1024 to a route, the Penalty is decreased by half after the half-life period expires. The default is 15 minutes. – reuse: the range is from 1 to 20000. This number is compared to the flapping route’s Penalty value. If the Penalty value is less than the reuse value, the flapping route is once again advertised (or no longer suppressed).
The following example shows how to configure values to reuse or restart a route. In the following example, default = 15 is the set time before the value decrements, bgp dampening 2 ? is the set re-advertise value, bgp dampening 2 2000 ? is the suppress value, and bgp dampening 2 2000 3000 ? is the time to suppress a route. Default values are also shown.
– keepalive: the range is from 1 to 65535. Time interval, in seconds, between keepalive messages sent to the neighbor routers. The default is 60 seconds. – holdtime: the range is from 3 to 65536. Time interval, in seconds, between the last keepalive message and declaring the router dead. The default is 180 seconds. To view non-default values, use the show config command in CONFIGURATION ROUTER BGP mode or the show runningconfig bgp command in EXEC Privilege mode.
Example of Soft-Reconfigration of a BGP Neighbor The example enables inbound soft reconfiguration for the neighbor 10.108.1.1. All updates received from this neighbor are stored unmodified, regardless of the inbound policy. When inbound soft reconfiguration is done later, the stored information is used to generate a new set of inbound updates. Dell>router bgp 100 neighbor 10.108.1.1 remote-as 200 neighbor 10.108.1.
• Exchange of IPv4 multicast route information occurs through the use of two new attributes called MP_REACH_NLRI and MP_UNREACH_NLRI, for feasible and withdrawn routes, respectively. • If the peer has not been activated in any AFI/SAFI, the peer remains in Idle state. Most Dell Networking OS BGP IPv4 unicast commands are extended to support the IPv4 multicast RIB using extra options to the command.
• debug ip bgp [ip-address | peer-group peer-group-name] updates [in | out] [prefix-list name] Enable soft-reconfiguration debug. EXEC Privilege mode debug ip bgp {ip-address | peer-group-name} soft-reconfiguration To enhance debugging of soft reconfig, use the bgp soft-reconfig-backup command only when route-refresh is not negotiated to avoid the peer from resending messages. In-BGP is shown using the show ip protocols command. Dell Networking OS displays debug messages on the console.
'UPDATE error/Missing well-known attr' Sent : 1 Recv: 0 'Connection Reset' Sent : 1 Recv: 0 Last notification (len 21) sent 00:26:02 ago ffffffff ffffffff ffffffff ffffffff 00160303 03010000 Last notification (len 21) received 00:26:20 ago ffffffff ffffffff ffffffff ffffffff 00150306 00000000 Last PDU (len 41) received 00:26:02 ago that caused notification to be issued ffffffff ffffffff ffffffff ffffffff 00290200 00000e01 02040201 00024003 04141414 0218c0a8 01000000 Local host: 1.1.1.
PDU[4] : len 19, captured 00:34:20 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] The following example shows how to view space requirements for storing all the PDUs. With full internet feed (205K) captured, approximately 11.8MB is required to store all of the PDUs. Dell(conf-router_bgp)#do show capture bgp-pdu neighbor 172.30.1.250 Incoming packet capture enabled for BGP neighbor 172.30.1.250 Available buffer size 29165743, 192991 packet(s) captured using 11794257 bytes [. . .
Figure 24. Sample Configurations Example of Enabling BGP (Router 1) R1# conf R1(conf)#int loop 0 R1(conf-if-lo-0)#ip address 192.168.128.1/24 R1(conf-if-lo-0)#no shutdown R1(conf-if-lo-0)#show config ! interface Loopback 0 ip address 192.168.128.1/24 no shutdown R1(conf-if-lo-0)#int te 1/21 R1(conf-if-te-1/21)#ip address 10.0.1.21/24 R1(conf-if-te-1/21)#no shutdown R1(conf-if-te-1/21)#show config ! interface TengigabitEthernet 1/21 ip address 10.0.1.
R1(conf-router_bgp)#neighbor 192.168.128.3 remote 100 R1(conf-router_bgp)#neighbor 192.168.128.3 no shut R1(conf-router_bgp)#neighbor 192.168.128.3 update-source loop 0 R1(conf-router_bgp)#show config ! router bgp 99 network 192.168.128.0/24 neighbor 192.168.128.2 remote-as 99 neighbor 192.168.128.2 update-source Loopback 0 neighbor 192.168.128.2 no shutdown neighbor 192.168.128.3 remote-as 100 neighbor 192.168.128.
R3(conf-if-te-3/11)#show config ! interface TengigabitEthernet 3/11 ip address 10.0.3.33/24 no shutdown R3(conf-if-lo-0)#int te 3/21 R3(conf-if-te-3/21)#ip address 10.0.2.3/24 R3(conf-if-te-3/21)#no shutdown R3(conf-if-te-3/21)#show config ! interface TengigabitEthernet 3/21 ip address 10.0.2.3/24 no shutdown R3(conf-if-te-3/21)# R3(conf-if-te-3/21)#router bgp 100 R3(conf-router_bgp)#show config ! router bgp 100 R3(conf-router_bgp)#network 192.168.128.0/24 R3(conf-router_bgp)#neighbor 192.168.128.
CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Update source set to Loopback 0 Peer active in peer-group outbound optimization For address family: IPv4 Unicast BGP table version 1, neighbor version 1 Prefixes accepted 1 (consume 4 bytes), withdrawn 0 by peer Prefixes advertised 1, denied 0, withdrawn 0 from peer Connections established 2; dropped 1 Last reset 00:00:57, due to user reset Notification History 'Connect
2 BGP path attribute entrie(s) using 128 bytes of memory 2 BGP AS-PATH entrie(s) using 90 bytes of memory 2 neighbor(s) using 9216 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 192.168.128.1 99 140 136 2 0 (0) 00:11:24 1 192.168.128.
Member of peer-group BBB for session parameters BGP version 4, remote router ID 192.168.128.
9 Content Addressable Memory (CAM) CAM is a type of memory that stores information in the form of a lookup table. On Dell Networking systems, CAM stores Layer 2 (L2) and Layer 3 (L3) forwarding information, access-lists (ACLs), flows, and routing policies. CAM Allocation CAM Allocation for Ingress To allocate the space for regions such has L2 ingress ACL, IPV4 ingress ACL, IPV6 ingress ACL, IPV4 QoS, L2 QoS, PBR, VRF ACL, and so forth, use the cam-acl command in CONFIGURATION mode.
NOTE: When you reconfigure CAM allocation, use the nlbclusteracl number command to change the number of NLB ARP entries. The range is from 0 to 2. The default value is 0. At the default value of 0, eight NLB ARP entries are available for use. This platform supports upto 256 CAM entries. Select 1 to configure 128 entries. Select 2 to configure 256 entries.
nlbcluster number ipv4pbr number openflow number | fcoe number iscsioptacl number [vrfv4acl number] NOTE: If you do not enter the allocation values for the CAM regions, the value is 0. 3. Execute write memory and verify that the new settings are written to the CAM on the next boot. EXEC Privilege mode show cam-acl 4. Reload the system. EXEC Privilege mode reload Test CAM Usage To determine whether sufficient CAM space is available to enable a service-policy, use the test-cam-usage command.
NOTE: If you select the CAM profile from CONFIGURATION mode, the output of this command does not reflect any changes until you save the running-configuration and reload the chassis. Example of show running-config cam-profile Command Dell#show running-config cam-profile ! cam-profile default microcode default Dell# View CAM-ACL Settings The show cam-acl command shows the cam-acl setting that will be loaded after the next reload.
The default values for the show cam-acl command are: Dell#show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 -- Stack unit 0 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDu
View CAM Usage View the amount of CAM space available, used, and remaining in each ACL partition using the show cam-usage command from EXEC Privilege mode.
DSA_QOS_CAM_INSTALL_FAILED: Not enough space in L3 Cam(PolicyQos) for class 5 (Te 1/ 22) entries on portpipe 1 for linecard 1 If you exceed the QoS CAM space, follow these steps. 1. Verify that you have configured a CAM profile that allocates 24 K entries to the IPv4 system flow region. 2. Allocate more entries in the IPv4Flow region to QoS. Dell Networking OS supports the ability to view the actual CAM usage before applying a service-policy.
scaled-l3-routes Forwarding table mode for scaling L3 route entries Dell(conf)# Dell(conf)#hardware forwarding-table mode scaled-l3-hosts Hardware forwarding-table mode is changed. Save the configuration and reload to take effect. Dell(conf)#end Dell#write mem ! 01:13:36: %STKUNIT0-M:CP %FILEMGR-5-FILESAVED: Copied running-config to startup-config in flash by default Dell(conf)# Dell(conf)#end Dell#01:13:44: %STKUNIT0-M:CP %SYS-5-CONFIG_I: Configured from console Dell# 2.
10 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. That filter prevents traffic not specifically identified as legitimate from reaching the system control plane, rate-limits, traffic to an acceptable level.
Figure 26. CoPP Implemented Versus CoPP Not Implemented Configure Control Plane Policing The system can process a maximum of 4200 packets per second (PPS). Protocols that share a single queue may experience flaps if one of the protocols receives a high rate of control traffic even though per protocol CoPP is applied. This happens because queuebased rate limiting is applied first.
Configuring CoPP for Protocols This section lists the commands necessary to create and enable the service-policies for CoPP. For complete information about creating ACLs and QoS rules, refer to Access Control Lists (ACLs) and Quality of Service (QoS). The basics for creating a CoPP service policy are to create a Layer 2, Layer 3, and/or an IPv6 ACL rule for the desired protocol type. Then, create a QoS input policy to rate-limit the protocol traffics according to the ACL.
Dell(conf)#mac access-list extended lacp cpu-qos Dell(conf-mac-acl-cpuqos)#permit lacp Dell(conf-mac-acl-cpuqos)#exit Dell(conf)#ipv6 access-list ipv6-icmp cpu-qos Dell(conf-ipv6-acl-cpuqos)#permit icmp Dell(conf-ipv6-acl-cpuqos)#exit Dell(conf)#ipv6 access-list ipv6-vrrp cpu-qos Dell(conf-ipv6-acl-cpuqos)#permit vrrp Dell(conf-ipv6-acl-cpuqos)#exit The following example shows creating the QoS input policy.
The basics for creating a CoPP service policy is to create QoS policies for the desired CPU bound queue and associate it with a particular rate-limit. The QoS policies are assigned to a control-plane service policy for each port-pipe. 1. Create a QoS input policy for the router and assign the policing. CONFIGURATION mode qos-policy-input name cpu-qos 2. Create an input policy-map to assign the QoS policy to the desired service queues.l.
Q6 Q7 Dell# 400 1100 Example of Viewing Queue Mapping To view the queue mapping for each configured protocol, use the show ip protocol-queue-mapping command.
11 Data Center Bridging (DCB) Ethernet Enhancements in Data Center Bridging The following section describes DCB. The device supports the following DCB features: • Data center bridging exchange protocol (DCBx) • Priority-based flow control (PFC) • Enhanced transmission selection (ETS) To configure PFC, ETS, and DCBx for DCB, refer to Sample DCB Configuration for the CLI configurations.
To ensure lossless delivery and latency-sensitive scheduling of storage and service traffic and I/O convergence of LAN, storage, and server traffic over a unified fabric, IEEE data center bridging adds the following extensions to a classical Ethernet network: • 802.1Qbb — Priority-based Flow Control (PFC) • 802.1Qaz — Enhanced Transmission Selection (ETS) • 802.
• If DCBx negotiation is not successful (for example, a version or TLV mismatch), DCBx is disabled and PFC or ETS cannot be enabled. • PFC supports buffering to receive data that continues to arrive on an interface while the remote system reacts to the PFC operation. • PFC uses DCB MIB IEEE 802.1azd2.5 and PFC MIB IEEE 802.1bb-d2.2 • PFC supports buffering to receive data that continues to arrive on an interface while the remote system reacts to the PFC operation. • PFC uses DCB MIB IEEE 802.1azd2.
Table 13. ETS Traffic Groupings Traffic Groupings Description Group ID A 4-bit identifier assigned to each priority group. The range is from 0 to 7 configurable; 8 - 14 reservation and 15.0 - 15.7 is strict priority group.. Group bandwidth Percentage of available bandwidth allocated to a priority group. Group transmission selection algorithm (TSA) Type of queue scheduling a priority group uses. In Dell Networking OS, ETS is implemented as follows: • ETS supports groups of 802.
Data Center Bridging in a Traffic Flow The following figure shows how DCB handles a traffic flow on an interface. Figure 28. DCB PFC and ETS Traffic Handling Enabling Data Center Bridging DCB is automatically configured when you configure FCoE or iSCSI optimization. Data center bridging supports converged enhanced Ethernet (CEE) in a data center network. DCB is disabled by default. It must be enabled to support CEE.
NOTE: To save the pfc buffering configuration changes, save the configuration and reboot the system. NOTE: Dell Networking OS Behavior: DCB is not supported if you enable link-level flow control on one or more interfaces. For more information, refer to Ethernet Pause Frames. DCB Maps and its Attributes This topic contains the following sections that describe how to configure a DCB map, apply the configured DCB map to a port, configure PFC without a DCB map, and configure lossless queues.
The default dot1p priority-queue assignments are applied as follows: Dell(conf)#do show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 7 Queue : 2 0 1 3 4 5 6 7 Dell(conf)# NOTE: In Egress queue assignment (8 queues in S6000 and Z9500, 4 against in S5000 and S4810. PFC is not applied on specific dot1p priorities. ETS: Equal bandwidth is assigned to each port queue and each dot1p priority in a priority group.
Leave a space between each priority group number. For example: priority-pgid 0 0 0 1 2 4 4 4 in which priority group 0 maps to dot1p priorities 0, 1, and 2; priority group 1 maps to dot1p priority 3; priority group 2 maps to dot1p priority 4; priority group 4 maps to dot1p priorities 5, 6, and 7. Dell Networking OS Behavior: As soon as you apply a DCB policy with PFC enabled on an interface, DCBx starts exchanging information with PFC-enabled peers. The IEEE802.
The maximum number of lossless queues globally supported on the switch is two. The range is from 0 to 7. Separate the queue values with a comma; specify a priority range with a dash; for example, pfc nodrop queues 1,7 or pfc no-drop queues 2-7. The default: No lossless queues are configured. NOTE: Dell Networking OS Behavior: By default, no lossless queues are configured on a port. A limit of two lossless queues is supported on a port.
• Traffic may be interrupted when you reconfigure PFC no-drop priorities in a DCB map or re-apply the DCB map to an interface. • For PFC to be applied, the configured priority traffic must be supported by a PFC peer (as detected by DCBx). • If you apply a DCB map with PFC disabled (pfc off), you can enable link-level flow control on the interface using the flowcontrol rx on tx on command. To delete the DCB map, first disable link-level flow control.
Step Task 1. Command Command Mode You cannot configure PFC using the pfc priority command on an interface on which a DCB map has been applied or which is already configured for lossless queues (pfc no-drop queues command). Configuring Lossless Queues DCB also supports the manual configuration of lossless queues on an interface when PFC mode is disabled in a DCB map, apply the map on the interface.
Step Task Command Command Mode fortygigabitEthernet slot/ port} 2 Open a DCB map and enter DCB map configuration mode. dcb-map name INTERFACE 3 Disable PFC. no pfc mode on DCB MAP 4 Return to interface configuration mode. exit DCB MAP 5 Apply the DCB map, created to disable the PFC operation, on the interface dcb-map {name | default} INTERFACE 6 Configure the port queues that still function as no-drop queues for lossless traffic. For the dot1p-queue assignments.
Buffer Sizes for Lossless or PFC Packets You can configure up to a maximum of 4 lossless (PFC) queues. By configuring 4 lossless queues, you can configure 4 different priorities and assign a particular priority to each application that your network is used to process. For example, you can assign a higher priority for time-sensitive applications and a lower priority for other services, such as file transfers.
Configuration Example for DSCP and PFC Priorities Consider a scenario in which the following DSCP and PFC priorities are necessary: DSCP 0 – 5, 10 - 15 Expected PFC Priority 1 20 – 25, 30 – 35 2 To configure the aforementioned DSCP and PFC priority values, perform the following tasks: 1. Create class-maps to group the DSCP subsets class-map match ip ! class-map match ip 2.
• pfcPerPrioTable fpEgrQBuffSnapshot This table fetches the BST statistics at Egress Port for the buffer used. This table displays the Snapshot of Table the Buffer cells used by Unicast and Multicast Data and Control Queues. fpIngPgBuffSnapsho This table fetches the BST statistics at the Ingress Port for the Shared Cells, and the Headroom cells used tTable per Priority Group.
Table 16. Dot1p to Queue Mapping PacketDot1p 0 1 2 3 4 5 6 7 Queue 2 0 1 3 4 5 6 7 PFC and ETS Configuration Examples This section contains examples of how to configure and apply DCB policies on an interface. Using PFC to Manage Converged Ethernet Traffic To use PFC for managing converged Ethernet traffic, use the following command: dcb-map stack-unit all dcb-map-name Operations on Untagged Packets The below is example for enabling PFC for priority 2 for tagged packets.
• Allocating a guaranteed share of bandwidth to each priority group. • Allowing each group to exceed its minimum guaranteed bandwidth if another group is not fully using its allotted bandwidth. ETS Prerequisites and Restrictions The following prerequisites and restrictions apply when you configure ETS bandwidth allocation or queue scheduling.
Leave a space between each priority group number. For example: priority-pgid 0 0 0 1 2 4 4 4 in which priority group 0 maps to dot1p priorities 0, 1, and 2; priority group 1 maps to dot1p priority 3; priority group 2 maps to dot1p priority 4; priority group 4 maps to dot1p priorities 5, 6, and 7. Dell Networking OS Behavior: A priority group consists of 802.1p priority values that are grouped for similar bandwidth allocation and scheduling, and that share latency and loss requirements. All 802.
The maximum 32 alphanumeric characters. 2. Configure the percentage of bandwidth to allocate to the dot1p priority/queue traffic in the associated L2 class map. QoS OUTPUT POLICY mode Dell(conf-qos-policy-out)#bandwidth-percentage 100 The default is none. 3. Repeat Step 2 to configure bandwidth percentages for other priority queues on the port. QoS OUTPUT POLICY mode Dell(conf-qos-policy-out)#bandwidth-percentage 100 4. Exit QoS Output Policy Configuration mode.
• Scheduling of priority traffic: dot1p priority traffic on the switch is scheduled to the current queue mapping. dot1p priorities within the same queue must have the same traffic properties and scheduling method.
Strict-priority groups: • If priority group 3 has free bandwidth, it is distributed as follows: 20% of the free bandwidth to priority group 1 and 30% of the free bandwidth to priority group 2. • If priority group 1 or 2 has free bandwidth, (20 + 30)% of the free bandwidth is distributed to priority group 3. Priority groups 1 and 2 retain whatever free bandwidth remains up to the (20+ 30)%.
• Detects DCB mis-configuration in a peer device; that is, when DCB features are not compatibly configured on a peer device and the local switch. Mis-configuration detection is feature-specific because some DCB features support asymmetric configuration. • Reconfigures a peer device with the DCB configuration from its configuration source if the peer device is willing to accept configuration.
configuration source, all PFC and application priority TLVs are enabled. ETS recommend TLVs are disabled and ETS configuration TLVs are enabled. Manual The port is configured to operate only with administrator-configured settings and does not auto-configure with DCB settings received from a DCBx peer or from an internally propagated configuration from the configuration source.
• If there is no configuration source, a port may elect itself as the configuration source. A port may become the configuration source if the following conditions exist: – No other port is the configuration source. – The port role is auto-upstream. – The port is enabled with link up and DCBx enabled. – The port has performed a DCBx exchange with a DCBx peer. – The switch is capable of supporting the received DCB configuration values through either a symmetric or asymmetric parameter exchange.
DCBx Example The following figure shows how to use DCBx. The external 40GbE 40GbE ports on the base module (ports 33 and 37) of two switches are used for uplinks configured as DCBx auto-upstream ports. The device is connected to third-party, top-of-rack (ToR) switches through 40GbE uplinks. The ToR switches are part of a Fibre Channel storage network. The internal ports (ports 1-32) connected to the 10GbE backplane are configured as auto-downstream ports. Figure 29.
interface type slot/port 2. Enter LLDP Configuration mode to enable DCBx operation. INTERFACE mode [no] protocol lldp 3. Configure the DCBx version used on the interface, where: auto configures the port to operate using the DCBx version received from a peer. PROTOCOL LLDP mode [no] DCBx version {auto | cee | cin | ieee-v2.5} • cee: configures the port to use CEE (Intel 1.01). • cin: configures the port to use Cisco-Intel-Nuova (DCBx 1.0). • ieee-v2.5: configures the port to use IEEE 802.
NOTE: To disable TLV transmission, use the no form of the command; for example, no advertise DCBx-applntlv iscsi. For information about how to use iSCSI, refer to iSCSI Optimization To verify the DCBx configuration on a port, use the show interface DCBx detail command. Configuring DCBx Globally on the Switch To globally configure the DCBx operation on a switch, follow these steps. 1. Enter Global Configuration mode. EXEC PRIVILEGE mode configure 2. Enter LLDP Configuration mode to enable DCBx operation.
NOTE: To disable TLV transmission, use the no form of the command; for example, no advertise DCBx-applntlv iscsi. 6. Configure the FCoE priority advertised for the FCoE protocol in Application Priority TLVs. PROTOCOL LLDP mode [no] fcoe priority-bits priority-bitmap The priority-bitmap range is from 1 to FF. The default is 0x8. 7. Configure the iSCSI priority advertised for the iSCSI protocol in Application Priority TLVs.
– tlv: enables traces for DCBx TLVs. Verifying the DCB Configuration To display DCB configurations, use the following show commands. Table 17. Displaying DCB Configurations Command Output show qos dot1p-queue mapping Displays the current 802.1p priority-queue mapping. show dcb [stack-unit unit-number] Displays the data center bridging status, number of PFC-enabled ports, and number of PFC-enabled queues. On the master switch in a stack, you can specify a stack-unit number. The range is from 0 to 5.
The following example shows the output of the show qos dcb-map test command. Dell#show qos dcb-map test ----------------------State :Complete PfcMode:ON -------------------PG:0 TSA:ETS BW:50 PFC:OFF Priorities:0 1 2 5 6 7 PG:1 TSA:ETS BW:50 Priorities:3 4 PFC:ON The following example shows the show interfaces pfc summary command.
Table 18. show interface pfc summary Command Description Fields Description Interface Interface type with stack-unit and port number. Admin mode is on; Admin is enabled PFC Admin mode is on or off with a list of the configured PFC priorities . When PFC admin mode is on, PFC advertisements are enabled to be sent and received from peers; received PFC configuration takes effect. The admin operational status for a DCBx exchange of PFC configuration is enabled or disabled.
Fields Description PFC TLV Statistics: Output TLV pkts Number of PFC TLVs transmitted. PFC TLV Statistics: Error pkts Number of PFC error packets received. PFC TLV Statistics: Pause Tx pkts Number of PFC pause frames transmitted. PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received The following example shows the show interface pfc statistics command.
Oper status is init ETS DCBx Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Dell(conf)# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled T
Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth 0 0,1,2,3,4,5,6,7 100% 1 0% 2 0% 3 0% 4 0% 5 0% 6 0% 7 0% Priority# Bandwidth TSA 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# 0 0,1,2,3,4,5,6,7 1 2 3 4 5 6 7 TSA ETS ETS ETS ETS ETS ETS ETS ETS 13% 13% 13% 13% 12% 12% 12% 12% ETS ETS ETS ETS ETS ETS ETS
Field Description Admin mode ETS mode: on or off. Admin Parameters ETS configuration on local port, including priority groups, assigned dot1p priorities, and bandwidth allocation. Remote Parameters ETS configuration on remote peer port, including Admin mode (enabled if a valid TLV was received or disabled), priority groups, assigned dot1p priorities, and bandwidth allocation.
Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 Stack unit 1 stack port all Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100%
P-PFC Configuration TLV enabled p-PFC Configuration TLV disabled F-Application priority for FCOE enabled f-Application Priority for FCOE disabled I-Application priority for iSCSI enabled i-Application Priority for iSCSI disabled ----------------------------------------------------------------------Interface TenGigabitEthernet 1/14 Remote Mac Address 00:01:e8:8a:df:a0 Port Role is Auto-Upstream DCBx Operational Status is Enabled Is Configuration Source? FALSE Local DCBx Compatibility mode is CEE Local DCBx C
Field Description Local DCBx Status: DCBx Max Version Supported Highest DCBx version supported in Control TLVs. Local DCBx Status: Sequence Number Sequence number transmitted in Control TLVs. Local DCBx Status: Acknowledgment Number Acknowledgement number transmitted in Control TLVs. Local DCBx Status: Protocol State Current operational state of DCBx protocol: ACK or IN-SYNC. Peer DCBx Status: DCBx Operational Version DCBx version advertised in Control TLVs received from peer device.
dot1p Value in the Incoming Frame Egress Queue Assignment 3 3 4 4 5 5 6 6 7 7 Configuring the Dynamic Buffer Method Priority-based flow control using dynamic buffer spaces is supported on the S6000 platform. To configure the dynamic buffer capability, perform the following steps: 1. Enable the DCB application. By default, DCB is enabled and link-level flow control is disabled on all interfaces. CONFIGURATION mode dcb enable 2. Configure the shared PFC buffer size and the total buffer size.
INTERFACE mode (conf-if-te) dcb-policy buffer-threshold buffer-threshold 8. Configuring Global total buffer size on stack ports. CONFIGURATION mode dcb pfc-total-buffer-size buffer-size stack-unit all port-set {port-pipe |all} Port-set number range is from 0 to 3. Sample DCB Configuration The following shows examples of using PFC and ETS to manage your data center traffic. In the following example: • Incoming SAN traffic is configured for priority-based flow control.
Figure 30. PFC and ETS Applied to LAN, IPC, and SAN Priority Traffic QoS Traffic Classification: The service-class dynamic dot1p command has been used in Global Configuration mode to map ingress dot1p frames to the queues shown in the following table. For more information, refer to QoS dot1p Traffic Classification and Queue Assignment.
dot1p Value in the Incoming Frame Priority Group Assignment 6 LAN 7 LAN The following describes the priority group-bandwidth assignment. Priority Group Bandwidth Assignment IPC 5% SAN 50% LAN 45% PFC and ETS Configuration Command Examples The following examples show PFC and ETS configuration commands to manage your data center traffic. 1. Enabling DCB Dell(conf)#dcb enable 2.
12 Dynamic Host Configuration Protocol (DHCP) DHCP is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network endstations (hosts) based on configuration policies determined by network administrators.
Option Number and Description Domain Name Server Option 6 Domain Name Option 15 Specifies the domain name servers (DNSs) that are available to the client. Specifies the domain name that clients should use when resolving hostnames via DNS. IP Address Lease Time Option 51 DHCP Message Type Option 53 Specifies the amount of time that the client is allowed to use an assigned IP address.
Assign an IP Address using DHCP The following section describes DHCP and the client in a network. When a client joins a network: 1. The client initially broadcasts a DHCPDISCOVER message on the subnet to discover available DHCP servers. This message includes the parameters that the client requires and might include suggested values for those parameters. 2. Servers unicast or broadcast a DHCPOFFER message in response to the DHCPDISCOVER that offers to the client values for the requested parameters.
you configure IP source address validation on a member port of a virtual local area network (VLAN) and then attempt to apply an access list to the VLAN, Dell Networking OS displays the first line in the following message. If you first apply an ACL to a VLAN and then attempt enable IP source address validation on one of its member ports, Dell Networking OS displays the second line in the following message. % Error: Vlan member has access-list configured. % Error: Vlan has an access-list configured.
ip dhcp server 2. Create an address pool and give it a name. DHCP mode pool name 3. Specify the range of IP addresses from which the DHCP server may assign addresses. DHCP mode network network/prefix-length • network: the subnet address. • prefix-length: specifies the number of bits used for the network portion of the address you specify. The prefix-length range is from 17 to 31. 4. Display the current pool configuration.
The default is 24 hours. Specifying a Default Gateway The IP address of the default router should be on the same subnet as the client. To specify a default gateway, follow this step. • Specify default gateway(s) for the clients on the subnet, in order of preference. DHCP default-router address Configure a Method of Hostname Resolution Dell systems are capable of providing DHCP clients with parameters for two methods of hostname resolution—using DNS or NetBIOS WINS.
DHCP mode pool name 2. Specify the client IP address. DHCP host address 3. Specify the client hardware address. DHCP hardware-address hardware-address type • hardware-address: the client MAC address. • type: the protocol of the hardware platform. The default protocol is Ethernet. Debugging the DHCP Server To debug the DHCP server, use the following command. • Display debug information for DHCP server.
• By default, the switch is configured to operate in Jumpstart mode as a DHCP client that sends DHCP requests to a DHCP server to retrieve configuration information (IP address, boot-image filename, and configuration file). All ports and management interfaces are brought up in Layer 3 mode and pre-configured with no shutdown and no ip address. For this reason, you cannot enter configuration commands to set up the switch.
INTERFACE mode ip address dhcp Dynamically assigned IP addresses can be released without removing the DHCP client operation on the interface on a switch configured as a DHCP client. 3. Manually acquire a new IP address from the DHCP server by releasing a dynamically acquired IP address while retaining the DHCP client configuration on the interface. EXEC Privilege mode release dhcp interface type slot/port 4. Acquire a new IP address with renewed lease time from a DHCP server.
DHCP Client Operation with Other Features The DHCP client operates with other Dell Networking OS features, as the following describes. Stacking The DHCP client daemon runs only on the master unit and handles all DHCP packet transactions. It periodically synchronizes the lease file with the standby unit. When a stack failover occurs, the new master requires the same DHCP server-assigned IP address on DHCP client interfaces.
The received stacking configuration is always applied on the master stack unit. option #230 "unit-number:3#priority:2#stack-group:14" Configure Secure DHCP DHCP as defined by RFC 2131 provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks.
When you enable DHCP snooping, the relay agent builds a binding table — using DHCPACK messages — containing the client MAC address, IP addresses, IP address lease time, port, VLAN ID, and binding type. Every time the relay agent receives a DHCPACK on a trusted port, it adds an entry to the table.
ipv6 dhcp snooping trust 3. Enable IPv6 DHCP snooping on a VLAN or range of VLANs. CONFIGURATION mode ipv6 dhcp snooping vlan vlan-id Adding a Static Entry in the Binding Table To add a static entry in the binding table, use the following command. • Add a static entry in the binding table. EXEC Privilege mode ip dhcp snooping binding mac Adding a Static IPV6 DHCP Snooping Binding Table To add a static entry in the snooping database, use the following command.
IP DHCP Relay Information-option IP DHCP Relay Trust Downstream : Disabled. : Disabled.
made. However, DHCP release and decline packets are allowed so that the DHCP snooping table can decrease in size. After the table usage falls below the maximum limit of 4000 entries, new IP address assignments are allowed. To view the number of entries in the table, use the show ip dhcp snooping binding command. This output displays the snooping binding table created using the ACK packets from the trusted port.
NOTE: Dynamic ARP inspection (DAI) uses entries in the L2SysFlow CAM region, a sub-region of SystemFlow. One CAM entry is required for every DAI-enabled VLAN. You can enable DAI on up to 16 VLANs on a system. However, the ExaScale default CAM profile allocates only nine entries to the L2SysFlow region for DAI. You can configure 10 to 16 DAIenabled VLANs by allocating more CAM space to the L2SysFlow region before enabling DAI. SystemFlow has 102 entries by default.
• Specify an interface as trusted so that ARPs are not validated against the binding table. INTERFACE mode arp inspection-trust Dell Networking OS Behavior: Introduced in Dell Networking OS version 8.2.1.0, DAI was available for Layer 3 only. However, Dell Networking OS version 8.2.1.1 extends DAI to Layer 2. Source Address Validation Using the DHCP binding table, Dell Networking OS can perform three types of source address validation (SAV). Table 22.
NOTE: Before enabling SAV With VLAN option, allocate at least one FP block to the ipmacacl CAM region. DHCP MAC Source Address Validation DHCP MAC source address validation (SAV) validates a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Dell Networking OS ensures that the packet’s source MAC address is checked against the CHADDR field in the DHCP header only for packets from snooped VLANs. • Enable DHCP MAC SAV.
Total cam count 1 deny count (0 packets) deny access-list on TenGigabitEthernet 1/2 Total cam count 2 deny vlan 10 count (0 packets) deny vlan 20 count (0 packets) The following output of the show ip dhcp snooping source-address-validation discard-counters interface interface command displays the number of SAV dropped packets on a particular interface.
13 Equal Cost Multi-Path (ECMP) This chapter describes configuring ECMP. ECMP for Flow-Based Affinity Flow-based affinity includes the following: • Link Bundle Monitoring Configuring the Hash Algorithm TeraScale has one algorithm that is used for link aggregation groups (LAGs), ECMP, and NH-ECMP, and ExaScale can use three different algorithms for each of these features. To adjust the ExaScale behavior to match TeraScale, use the following command.
Dell Networking OS provides a command line interface (CLI)-based solution for modifying the hash seed to ensure that on each configured system, the ECMP selection is same. When configured, the same seed is set for ECMP, LAG, and NH, and is used for incoming traffic only. NOTE: While the seed is stored separately on each port-pipe, the same seed is used across all CAMs. NOTE: You cannot separate LAG and ECMP, but you can use different algorithms across the chassis with the same seed.
To configure the maximum number of paths, use the following command. NOTE: For the new settings to take effect, save the new ECMP settings to the startup-config (write-mem) then reload the system. • Configure the maximum number of paths per ECMP group. CONFIGURATION mode. • ip ecmp-group maximum-paths {2-64} Enable ECMP group path management. CONFIGURATION mode.
The range is from 1 to 64. Viewing an ECMP Group NOTE: An ecmp-group index generates automatically for each unique ecmp-group when you configure multipath routes to the same network. The system can generate a maximum of 512 unique ecmp-groups. The ecmp-group indices are generated in even numbers (0, 2, 4, 6... 1022) and are for information only. You can configure ecmp-group with id 2 for link bundle monitoring.
Support for moving /128 IPv6 Prefixes and /32 IPv4 Prefixes The software supports a command to program IPv6 /128 route prefixes in the route table. You can define IPv6 /128 route prefixes in the route table using the ipv6 unicast-host-routecommand. You can also define IPv4 /32 route prefixes in the host table using the ipv4 unicast-host-routecommand.
14 FCoE Transit The Fibre Channel over Ethernet (FCoE) Transit feature is supported on Ethernet interfaces. When you enable the switch for FCoE transit, the switch functions as a FIP snooping bridge. NOTE: FIP snooping is not supported on Fibre Channel interfaces or in a Fibre Channel over Ethernet FCoE provides a converged Ethernet network that allows the combination of storage-area network (SAN) and LAN traffic on a Layer 2 link by encapsulating Fibre Channel data into Ethernet frames.
Table 23. FIP Functions FIP Function Description FIP VLAN discovery FCoE devices (ENodes) discover the FCoE VLANs on which to transmit and receive FIP and FCoE traffic. FIP discovery FCoE end-devices and FCFs are automatically discovered. Initialization FCoE devices learn ENodes from the FLOGI and FDISC to allow immediate login and create a virtual link with an FCoE switch. Maintenance A valid virtual link between an FCoE device and an FCoE switch is maintained and the LOGO functions properly.
Dynamic ACL generation on the switch operating as a FIP snooping bridge function as follows: Port-based ACLs These ACLs are applied on all three port modes: on ports directly connected to an FCF, server-facing ENode ports, and bridge-to-bridge links. Port-based ACLs take precedence over global ACLs. FCoE-generated ACLs These take precedence over user-configured ACLs. A user-configured ACL entry cannot deny FCoE and FIP snooping frames.
• To assign a MAC address to an FCoE end-device (server ENode or storage device) after a server successfully logs in, set the FCoE MAC address prefix (FC-MAP) value an FCF uses. The FC-MAP value is used in the ACLs installed in bridge-to-bridge links on the switch. • To provide more port security on ports that are directly connected to an FCF and have links to other FIP snooping bridges, set the FCF or Bridge-to-Bridge Port modes.
Important Points to Remember • Enable DCBx on the switch before enabling the FIP Snooping feature. • To enable the feature on the switch, configure FIP Snooping. • To allow FIP frames to pass through the switch on all VLANs, enable FIP snooping globally on a switch. • A switch can support a maximum eight VLANs. Configure at least one FCF/bridge-to-bridge port mode interface for any FIP snooping-enabled VLAN. • You can configure multiple FCF-trusted interfaces in a VLAN.
If you disable FCoE transit, FIP and FCoE traffic are handled as normal Ethernet frames and no FIP snooping ACLs are generated. The VLAN-specific and FIP snooping configuration is disabled and stored until you re-enable FCoE transit and the configurations are re-applied. Enable FIP Snooping on VLANs You can enable FIP snooping globally on a switch on all VLANs or on a specified VLAN.
Table 24. Impact of Enabling FIP Snooping Impact Description MAC address learning MAC address learning is not performed on FIP and FCoE frames, which are denied by ACLs dynamically created by FIP snooping on server-facing ports in ENode mode. MTU auto-configuration MTU size is set to mini-jumbo (2500 bytes) when a port is in Switchport mode, the FIP snooping feature is enabled on the switch, and FIP snooping is enabled on all or individual VLANs.
5. Enable FIP snooping on all VLANs or on a specified VLAN. CONFIGURATION mode or VLAN INTERFACE mode. fip-snooping enable 6. Configure the port for bridge-to-FCF links. INTERFACE mode or CONFIGURATION mode fip-snooping port-mode fcf NOTE: To disable the FCoE transit feature or FIP snooping on VLANs, use the no version of a command; for example, no feature fip-snooping or no fip-snooping enable. Displaying FIP Snooping Information Use the following show commands to display information on FIP snooping, .
aa:bb:cc:00:00:00 aa:bb:cc:00:00:00 Te 1/42 Te 1/42 FCoE MAC 0e:fc:00:01:00:01 0e:fc:00:01:00:02 0e:fc:00:01:00:03 0e:fc:00:01:00:04 0e:fc:00:01:00:05 FC-ID 01:00:01 01:00:02 01:00:03 01:00:04 01:00:05 aa:bb:cd:00:00:00 aa:bb:cd:00:00:00 Te 1/43 Te 1/43 Port WWPN 31:00:0e:fc:00:00:00:00 41:00:0e:fc:00:00:00:00 41:00:0e:fc:00:00:00:01 41:00:0e:fc:00:00:00:02 41:00:0e:fc:00:00:00:03 100 100 Port WWNN 21:00:0e:fc:00:00:00:00 21:00:0e:fc:00:00:00:00 21:00:0e:fc:00:00:00:00 21:00:0e:fc:00:00:00:00 21:00:
The following example shows the show fip-snooping fcf command. Dell# show fip-snooping fcf FCF MAC FCF Interface VLAN FC-MAP FKA_ADV_PERIOD No. of Enodes ------------------- ---- ------------------- ------------54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 The following table describes the show fip-snooping fcf command fields. Table 28. show fip-snooping fcf Command Description Field Description FCF MAC MAC address of the FCF.
Number Number Number Number Number Number Number Number Number of of of of of of of of of FLOGI Rejects FDISC Accepts FDISC Rejects FLOGO Accepts FLOGO Rejects CVL FCF Discovery Timeouts VN Port Session Timeouts Session failures due to Hardware Config :0 :0 :0 :0 :0 :0 :0 :0 :0 The following example shows the show fip-snooping statistics port-channel command.
Field Description Number of Multicast Discovery Advertisements Number of FIP-snooped multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snooped unicast discovery advertisements received on the interface. Number of FLOGI Accepts Number of FIP FLOGI accept frames received on the interface. Number of FLOGI Rejects Number of FIP FLOGI reject frames received on the interface.
FCoE Transit Configuration Example The following illustration shows a switch used as a FIP snooping bridge for FCoE traffic between an ENode (server blade) and an FCF (ToR switch). The ToR switch operates as an FCF and FCoE gateway. Figure 35. Configuration Example: FIP Snooping on a Switch In this example, DCBx and PFC are enabled on the FIP snooping bridge and on the FCF ToR switch.
Example of Configuring the ENode Server-Facing Port Dell(conf)# interface tengigabitethernet 1/1 Dell(conf-if-te-1/1)# portmode hybrid Dell(conf-if-te-1/1)# switchport Dell(conf-if-te-1/1)# protocol lldp Dell(conf-if-te-1/1-lldp)# dcbx port-role auto-downstream NOTE: A port is enabled by default for bridge-ENode links.
15 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Flex Hash Capability Overview This functionality is supported on the S6000 platform. The flex hash functionality enables you to configure a packet search key and matches packets based on the search key. When a packet matches the search key, two 16-bit hash fields are extracted from the start of the L4 header and provided as inputs (bins 2 and 3) for RTAG7 hash computation.
CONFIGURATION mode Dell(conf)# load-balance flexhash ipv4/ipv6 ip-proto offset1 [offset2 ] To delete the configured flex hash setting, use the no version of the command. Configuring Fast Boot and LACP Fast Switchover Configure the optimized booting time functionality by performing the following steps. This procedure is supported on the S6000 platform. 1. Enable the system to restart with optimized booting-time functionality enabled.
Networking OS Release 9.3(0.0) or later, or when you perform a planned upgrade (and not an abrupt or unexpected shutdown) from an older release of Dell Networking OS to Release 9.3(0.0) or later. Dell recommends that you do not downgrade your system from Release 9.3(0.0) to an earlier release that does not support the fast boot functionality because the system behavior is unexpected and undefined.
The system saves all dynamic ARP entries to a database on the flash drive. A file is generated to indicate that the system is undergoing a fast boot, which is used after the system comes up.
Cold Boot Caused by Power Cycling the System When you perform a power-cycle operation on a system that is configured with the optimized booting functionality, the system goes through its regular boot sequence even if it is configured for fast boot. When the system comes up, it is expected that there will be no dynamic ARP or ND database to restore.
While the above change will ensure that at least one path to each destination gets into the FIB as quickly as possible, it does prevent additional paths from being used even if they are available. This downside has been deemed to be acceptable. RDMA Over Converged Ethernet (RoCE) Overview This functionality is supported on the S6000 platform.
into multiple, different sub-VLANs, each VLAN is denoted by a unique 8021.Q tag to enable the nodes that receive the traffic frames determine the VLAN for which the frames are destined. Typically, a Layer 3 physical interface processes only untagged or priority-tagged packets. Tagged packets that are received on Layer 3 physical interfaces are dropped.
16 Force10 Resilient Ring Protocol (FRRP) FRRP provides fast network convergence to Layer 2 switches interconnected in a ring topology, such as a metropolitan area network (MAN) or large campuses. FRRP is similar to what can be achieved with the spanning tree protocol (STP), though even with optimizations, STP can take up to 50 seconds to converge (depending on the size of network and node of failure) may require 4 to 5 seconds to reconverge.
Ring Checking At specified intervals, the Master node sends a ring health frame (RHF) through the ring. If the ring is complete, the frame is received on its secondary port and the Master node resets its fail-period timer and continues normal operation. If the Master node does not receive the RHF before the fail-period timer expires (a configurable timer), the Master node moves from the Normal state to the Ring-Fault state and unblocks its Secondary port.
• One Master node per ring — all other nodes are Transit. • Each node has two member interfaces — primary and secondary. • There is no limit to the number of nodes on a ring. • Master node ring port states — blocking, pre-forwarding, forwarding, and disabled. • Transit node ring port states — blocking, pre-forwarding, forwarding, and disabled. • STP disabled on ring interfaces. • Master node secondary port is in blocking state during Normal operation.
Concept Explanation • Hello RHF (HRHF) — These frames are processed only on the Master node’s Secondary port. The Transit nodes pass the HRHF through without processing it. An HRHF is sent at every Hello interval. • Topology Change RHF (TCRHF) — These frames contains ring status, keepalive, and the control and member VLAN hash. The TCRHF is processed at each node of the ring.
Configuring the Control VLAN Control and member VLANS are configured normally for Layer 2. Their status as control or member is determined at the FRRP group commands. For more information about configuring VLANS in Layer 2 mode, refer to Layer 2. Be sure to follow these guidelines: • All VLANS must be in Layer 2 mode. • You can only add ring nodes to the VLAN. • A control VLAN can belong to one FRRP group only. • Tag control VLAN ports.
VLAN-ID, Range: VLAN IDs for the ring’s member VLANS. 6. Enable FRRP. CONFIG-FRRP mode. no disable Configuring and Adding the Member VLANs Control and member VLANS are configured normally for Layer 2. Their status as Control or Member is determined at the FRRP group commands. For more information about configuring VLANS in Layer 2 mode, refer to the Layer 2 chapter. Be sure to follow these guidelines: • All VLANS must be in Layer 2 mode. • Tag control VLAN ports.
VLAN-ID, Range: VLAN IDs for the ring’s Member VLANs. 6. Enable this FRRP group on this switch. CONFIG-FRRP mode. no disable Setting the FRRP Timers To set the FRRP timers, use the following command. NOTE: Set the Dead-Interval time 3 times the Hello-Interval. • Enter the desired intervals for Hello-Interval or Dead-Interval times. CONFIG-FRRP mode. timer {hello-interval|dead-interval} milliseconds – Hello-Interval: the range is from 50 to 2000, in increments of 50 (default is 500).
Ring ID: the range is from 1 to 255. Troubleshooting FRRP To troubleshoot FRRP, use the following information. Configuration Checks • Each Control Ring must use a unique VLAN ID. • Only two interfaces on a switch can be Members of the same control VLAN. • There can be only one Master node for any FRRP group. • You can configure FRRP on Layer 2 interfaces only. • Spanning Tree (if you enable it globally) must be disabled on both Primary and Secondary interfaces when you enable FRRP.
no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! interface Vlan 201 no ip address tagged TenGigabitEthernet 2/14,31 no shutdown ! protocol frrp 101 interface primary TenGigabitEthernet 2/14 secondary TenGigabitEthernet 2/31 control-vlan 101 member-vlan 201 mode transit no disable Example of R3 TRANSIT interface TenGigabitEthernet 3/14 no ip address switchport no shutdown ! interface TenGigabitEthernet 3/21 no ip address switchport no shutdown ! interface Vlan 101 no ip address tagged TenGigabi
17 GARP VLAN Registration Protocol (GVRP) GARP VLAN registration protocol (GVRP) is supported on Dell Networking OS. Typical virtual local area network (VLAN) implementation involves manually configuring each Layer 2 switch that participates in a given VLAN. GVRP, defined by the IEEE 802.1q specification, is a Layer 2 network protocol that provides for automatic VLAN configuration of switches. GVRP-compliant switches use GARP to register and de-register attribute values, such as VLAN IDs, with each other.
Figure 36. Global GVRP Configuration Example Basic GVRP configuration is a two-step process: 1. Enabling GVRP Globally 2. Enabling GVRP on a Layer 2 Interface Related Configuration Tasks • • Configure GVRP Registration Configure a GARP Timer Enabling GVRP Globally To configure GVRP globally, use the following command. • Enable GVRP for the entire switch.
protocol gvrp no disable Dell(config-gvrp)# To inspect the global configuration, use the show gvrp brief command. Enabling GVRP on a Layer 2 Interface To enable GVRP on a Layer 2 interface, use the following command. • Enable GVRP on a Layer 2 interface.
no shutdown Dell(conf-if-te-1/21)# Configure a GARP Timer Set GARP timers to the same values on all devices that are exchanging information using GVRP. There are three GARP timer settings. • Join — A GARP device reliably transmits Join messages to other devices by sending each Join message two times. To define the interval between the two sending operations of each Join message, use this parameter. The Dell Networking OS default is 200ms.
18 Internet Group Management Protocol (IGMP) Internet group management protocol (IGMP) is supported on Dell Networking OS. Multicast is premised on identifying many hosts by a single destination IP address; hosts represented by the same IP address are a multicast group. IGMP is a Layer 3 multicast protocol that hosts use to join or leave a multicast group.
Figure 37. IGMP Messages in IP Packets Join a Multicast Group There are two ways that a host may join a multicast group: it may respond to a general query from its querier or it may send an unsolicited report to its querier. Responding to an IGMP Query The following describes how a host can join a multicast group. 1. One router on a subnet is elected as the querier. The querier periodically multicasts (to all-multicast-systems address 224.0.0.1) a general query to all hosts on the subnet. 2.
• To enable filtering, routers must keep track of more state information, that is, the list of sources that must be filtered. An additional query type, the Group-and-Source-Specific Query, keeps track of state changes, while the Group-Specific and General queries still refresh the existing state.
3. The host’s third message indicates that it is only interested in traffic from sources 10.11.1.1 and 10.11.1.2. Because this request again prevents all other sources from reaching the subnet, the router sends another group-and-source query so that it can satisfy all other hosts. There are no other interested hosts so the request is recorded. Figure 40.
Figure 41. Membership Queries: Leaving and Staying Configure IGMP Configuring IGMP is a two-step process. 1. Enable multicast routing using the ip multicast-routing command. 2. Enable a multicast routing protocol.
Viewing IGMP Enabled Interfaces Interfaces that are enabled with PIM-SM are automatically enabled with IGMP. To view IGMP-enabled interfaces, use the following command. • View IGMP-enabled interfaces. EXEC Privilege mode show ip igmp interface Example of the show ip igmp interface Command Dell#show ip igmp interface TenGigabitEthernet 3/10 Inbound IGMP access group is not set Internet address is 165.87.34.
• View both learned and statically configured IGMP groups. EXEC Privilege mode show ip igmp groups Example of the show ip igmp groups Command Dell# show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface 225.1.1.1 TenGigabitEthernet 1/1 225.1.2.1 TenGigabitEthernet 1/1 Mode IGMPV2 IGMPV2 Uptime 00:11:19 00:10:19 Expires 00:01:50 00:01:50 Last Reporter 165.87.34.100 165.87.31.
the last member query interval (LMQI). The switch waits one LMQI after the second query before removing the group from the state table. • Adjust the period between queries. INTERFACE mode ip igmp query-interval • Adjust the maximum response time. INTERFACE mode ip igmp query-max-resp-time • Adjust the last member query interval.
Configuring IGMP Snooping Configuring IGMP snooping is a one-step process. To enable, view, or disable IGMP snooping, use the following commands. There is no specific configuration needed for IGMP snooping with virtual link trunking (VLT). For information about VLT configurations, refer to Virtual Link Trunking (VLT). • Enable IGMP snooping on a switch. CONFIGURATION mode ip igmp snooping enable • View the configuration. CONFIGURATION mode show running-config • Disable snooping on a VLAN.
Disabling Multicast Flooding If the switch receives a multicast packet that has an IP address of a group it has not learned (unregistered frame), the switch floods that packet out of all ports on the VLAN. When you configure the no ip igmp snooping flood command, the system drops the packets immediately. The system does not forward the frames on mrouter ports, even if they are present. Disable Layer 3 multicast (no ip multicast-routing) in order to disable multicast flooding.
Fast Convergence after MSTP Topology Changes The following describes the fast convergence feature. When a port transitions to the Forwarding state as a result of an STP or MSTP topology change, Dell Networking OS sends a general query out of all ports except the multicast router ports. The host sends a response to the general query and the forwarding database is updated without having to wait for the query interval to expire.
Application Name Port Number Client SNMP 162 for SNMP Traps (client), Supported Server 161 for SNMP MIB response (server) NTP 123 Supported DNS 53 Supported FTP 20/21 Supported Syslog 514 Supported Telnet 23 Supported TFTP 69 Supported Radius 1812,1813 Supported Tacacs 49 Supported HTTP 80 for httpd Supported Supported Supported 443 for secure httpd 8008 HTTP server port for confd application 8888 secure HTTP server port for confd application If you configure a source int
• Applications can be configured or unconfigured as management applications using the application or no application command. All configured applications are considered as management applications and the rest of them as non-management applications. • All the management routes (connected, static and default) are duplicated and added to the management EIS routing table. • Any new management route added is installed to both the EIS routing table and default routing table.
application, then sin_port of destination sockaddr structure is set to Management EIS ID 2 so that route lookup can be done in the management EIS routing table. • To ensure that protocol separation is done only for switch initiated traffic where the application acts as client, only the destination TCP/UDP port is compared and not the source TCP/UDP port. The source TCP/UDP port becomes a known port number when the box acts as server. • TFTP is an exception to the preceding logic.
applications takes a preference for ip1 as source IP and uses the management network to reach the destination. If the management port is down or the route lookup in EIS routing table fails, ip2 is the source IP and the front-panel port is used to reach the destination. The fallback route between the management and data networks is used in such a case. At any given time, end users can access Dell Networking OS applications using either ip1 or ip2.
Switch-Destined Traffic This phenomenon occurs where traffic is terminated on the switch. Traffic has not originated from the switch and is not transiting the switch. The switch accepts all traffic destined to the switch, which is received on management or front-end data port. Response traffic with management port IP address as source IP address is handled in the same manner as switch originated traffic. Switch-Originated Traffic This phenomenon occurs where traffic is originating from the switch. 1.
Protocol Behavior when EIS is Enabled Behavior when EIS is Disabled telnet EIS Behavior Default Behavior tftp EIS Behavior Default Behavior icmp (ping and traceroute) EIS Behavior for ICMP Default Behavior Behavior of Various Applications for Switch-Destined Traffic This section describes the different system behaviors that occur when traffic is terminated on the switch. Traffic has not originated from the switch and is not transiting the switch.
VLT feature is for the front-end port only. Because this feature is specific to the management port, this feature can coexist with VLT and nothing specific needs to be done in this feature to handle VLT scenario. DHCP • If DHCP Client is enabled on the management port, a management default route is installed to the switch. • If management EIS is enabled, this default route is added to the management EIS routing table and the default routing table.
19 Interfaces This chapter describes interface types, both physical and logical, and how to configure them with Dell Networking Operating System (OS). • 10 Gigabit Ethernet / 40 Gigabit Ethernet interfaces are supported on the S6000 platform.
Interface Type Modes Possible Default Mode Requires Creation Default State Port Channel L2, L3 L3 Yes Shutdown (disabled) VLAN L2, L3 L2 Yes (except default) L2 - Shutdown (disabled) L3 - No Shutdown (enabled) Fibre Channel Interface TF, F, EPort TFport No Shutdown View Basic Interface Information To view basic interface information, use the following command. You have several options for viewing interface status and configuration parameters.
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 3 Broadcasts, 0 Unicasts 0 Vlans, 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 00:00:31 Dell# To view which interfaces are enabled for Layer 3 data transmission, use the show ip interfaces brief command in EXEC Privilege mode.
• 2. For the Management interface on the RPM, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. Enable the interface. INTERFACE mode no shutdown To confirm that the interface is enabled, use the show config command in INTERFACE mode. To leave INTERFACE mode, use the exit command or end command. You cannot delete a physical interface.
show interface transceiver QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 0 0 0 0 0 0 0 0 0 0 0 0 Serial ID Base Fields Id Ext Id Connector Transceiver Code Encoding Length(SFM) Km Length(OM3) 2m Length(OM2) 1m Length(OM1) 1m Length(Copper) 1m Vendor Rev = = = = = = = = = = = 0x0d 0x00 0x0c 0x04 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x05 0x00 0x32 0x00 0x00 0x00 0 Overview of Layer Modes On all systems running Dell Networking OS, you can place physical interfaces, port channels, and VLANs in
Configuring Layer 2 (Interface) Mode To configure an interface in Layer 2 mode, use the following commands. • Enable the interface. INTERFACE mode no shutdown • Place the interface in Layer 2 (switching) mode. INTERFACE mode switchport To view the interfaces in Layer 2 mode, use the show interfaces switchport command in EXEC mode. Configuring Layer 3 (Network) Mode When you assign an IP address to a physical interface, you place it in Layer 3 mode.
• Configure a primary IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] The ip-address must be in dotted-decimal format (A.B.C.D) and the mask must be in slash format (/xx). Add the keyword secondary if the IP address is the interface’s backup IP address. Example of the show ip interface Command You can only configure one primary IP address per interface. You can configure up to 255 secondary IP addresses on a single interface.
management egress-interface-selection 2. Configure which applications uses EIS. EIS mode application {all | application-type} NOTE: If you configure SNMP as the management application for EIS and you add a default management route, when you perform an SNMP walk and check the debugging logs for the source and destination IPs, the SNMP agent uses the destination address of incoming SNMP packets as the source address for outgoing SNMP responses for security.
Example of the show interface and show ip route Commands To display the configuration for a given port, use the show interface command in EXEC Privilege mode, as shown in the following example. To display the routing table, use the show ip route command in EXEC Privilege mode.
! tagged TenGigabitEthernet 2/2-13 tagged TenGigabitEthernet 5/1 ip ospf authentication-key force10 ip ospf cost 1 ip ospf dead-interval 60 ip ospf hello-interval 15 no shutdown Loopback Interfaces A Loopback interface is a virtual interface in which the software emulates an interface. Packets routed to it are processed locally. Because this interface is not a physical interface, you can configure routing protocols on this interface to provide protocol stability.
Port Channel Definition and Standards Link aggregation is defined by IEEE 802.3ad as a method of grouping multiple physical interfaces into a single logical interface—a link aggregation group (LAG) or port channel. A LAG is “a group of links that appear to a MAC client as if they were a single link” according to IEEE 802.3ad. In Dell Networking OS, a LAG is referred to as a port channel interface. A port channel provides redundancy by aggregating physical interfaces into one logical interface.
10/100/1000 Mbps Interfaces in Port Channels When both 10/100/1000 interfaces and GigE interfaces are added to a port channel, the interfaces must share a common speed. When interfaces have a configured speed different from the port channel speed, the software disables those interfaces. The common speed is determined when the port channel is first enabled. At that time, the software checks the first interface listed in the port channel configuration.
You can configure a port channel as you would a physical interface by enabling or configuring protocols or assigning access control lists. Adding a Physical Interface to a Port Channel The physical interfaces in a port channel can be on any line card in the chassis, but must be the same physical type.
The following example shows the port channel’s mode (L2 for Layer 2 and L3 for Layer 3 and L2L3 for a Layer 2-port channel assigned to a routed VLAN), the status, and the number of interfaces belonging to the port channel. Dell>show interface port-channel 20 Port-channel 20 is up, line protocol is up Hardware address is 00:01:e8:01:46:fa Internet address is 1.1.120.
INTERFACE PORT-CHANNEL mode interface port-channel id number 3. Add the interface to the second port channel. INTERFACE PORT-CHANNEL mode channel-member interface Example of Moving an Interface to a New Port Channel The following example shows moving the TenGigabitEthernet 1/8 interface from port channel 4 to port channel 3.
Dell(conf-if)#switchport 3. Verify the manually configured VLAN membership (show interfaces switchport interface command).
NOTE: Hash-based load-balancing on multi-protocol label switching (MPLS) does not work when you enable packetbased hashing (load-balance ip-selection packet-based). Load-Balancing Method For LAG hashing on the source IP, destination IP, source transmission control protocol (TCP)/user datagram protocol (UDP) port, and destination TCP/UDP port are used for hash computation by default. For packets without a Layer 3 header, Dell Networking OS automatically uses load-balance mac source-dest-mac.
• Change to another algorithm. CONFIGURATION mode hash-algorithm [ecmp{crc16|crc16cc|crc32LSB|crc32MSB|crc-upper|dest-ip|lsb|xor1|xor2| xor4|xor8|xor16}] Example of the hash-algorithm Command Dell(conf)#hash-algorithm ecmp xor 26 lag crc 26 nh-ecmp checksum 26 Dell(conf)# The hash-algorithm command is specific to ECMP group. The default ECMP hash configuration is crc-lower. This command takes the lower 32 bits of the hash key to compute the egress port.
Bulk Configuration Examples Use the interface range command for bulk configuration. • Create a Single-Range • Create a Multiple-Range • Exclude Duplicate Entries • Exclude a Smaller Port Range • Overlap Port Ranges • Commas • Add Ranges Create a Single-Range The following is an example of a single range.
Commas The following is an example of how to use commas to add different interface types to the range, enabling all TenGigabitEthernet interfaces in the range 5/1 to 5/23 and both Ten Gigabit Ethernet interfaces 1/1 and 1/2.
Monitoring and Maintaining Interfaces Monitor interface statistics with the monitor interface command. This command displays an ongoing list of the interface status (up/down), number of packets, traffic statistics, and so on. To view the interface’s statistics, use the following command. • View the interface’s statistics. EXEC Privilege mode Enter the type of interface and slot/port information: – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
q Dell# Maintenance Using TDR The time domain reflectometer (TDR) is supported on all Dell Networking switch/routers. TDR is an assistance tool to resolve link issues that helps detect obvious open or short conditions within any of the four copper pairs. TDR sends a signal onto the physical cable and examines the reflection of the signal that returns.
Example: stack-unit 0 quad-port-profile[default|list of ports] To display the Fan-out capability profile, use the following show command: show system stack-unit quad-port-profile Example of the show Command The following example shows the system stack-unit quad-port-profile command.
To split a single 40G port into four 10G ports, use the following command. • Split a single 40G port into four 10G ports. CONFIGURATION mode stack-unit stack-unit port number portmode quad – stack-unit: enter the stack member unit identifier of the stack member to reset. The range is from 0 to 11 – number: enter the port number of the 40G port to be split. Important Points to Remember • Splitting a 40G port into four 10G ports is supported on standalone and stacked units.
• Before using the QSA to convert a 40 Gigabit Ethernet port to a 10 Gigabit SFP or SFP+ port, enable 40 G to 4*10 fan-out mode on the device. • When you insert a QSA into a 40 Gigabit port, you can use only the first 10 Gigabit port in the fan-out mode to plug-in SFP or SFP+ cables. The remaining three 10 Gigabit ports are perceived to be in Link Down state and are unusable. • You cannot use QSFP Optical cables on the same port where QSA is used.
SFP+ 0 Serial ID Base Fields SFP+ 0 Id SFP+ 0 Ext Id SFP+ 0 Connector ………………………. = 0x0d = 0x00 = 0x23 Dell#show interfaces tengigabitethernet 0/3 transceiver SFP+ 0 Serial ID Base Fields SFP+ 0 Id = 0x0d SFP+ 0 Ext Id = 0x00 SFP+ 0 Connector = 0x23 ……………………….
QSFP 0 Id = 0x0d QSFP 0 Ext Id = 0x00 QSFP 0 Connector = 0x23 QSFP 0 Transceiver Code = 0x08 0x00 0x00 0x00 0x00 0x00 0x00 0x00 QSFP 0 Encoding = 0x00 ……………… ……………… QSFP 0 Diagnostic Information =================================== QSFP 0 Rx Power measurement type = OMA =================================== QSFP 0 Temp High Alarm threshold = 0.000C QSFP 0 Voltage High Alarm threshold = 0.000V QSFP 0 Bias High Alarm threshold = 0.
Dell#show interfaces tengigabitethernet 0/4 gigabitethernet 0/0 is up, line protocol is up Hardware is DellEth, address is 90:b1:1c:f4:9a:fa Current address is 90:b1:1c:f4:9a:fa Pluggable media present, SFP type is 1GBASE …………………… LineSpeed 1000 Mbit Dell#show interfaces tengigabitethernet 0/5 gigabitethernet 0/0 is up, line protocol is down Hardware is DellEth, address is 90:b1:1c:f4:9a:fa Current address is 90:b1:1c:f4:9a:fa Pluggable media present, SFP type is 1GBASE …………………… LineSpeed 1000 Mbit Dell#sho
Link Dampening Interface state changes occur when interfaces are administratively brought up or down or if an interface state changes. Every time an interface changes a state or flaps, routing protocols are notified of the status of the routes that are affected by the change in state. These protocols go through the momentous task of re-converging. Flapping; therefore, puts the status of entire network at risk of transient loops and black holes.
Te 1/2 Te 3/1 Te 4/2 Dell# Clearing Dampening Counters To clear dampening counters and accumulated penalties, use the following command. • Clear dampening counters.
• Enable link bundle monitoring. ecmp-group • View all LAG link bundles being monitored. show running-config ecmp-group Using Ethernet Pause Frames for Flow Control Ethernet pause frames and threshold settings are supported on the Dell Networking OS. Ethernet Pause Frames allow for a temporary stop in data transmission. A situation may arise where a sending device may transmit data faster than a destination device can accept it.
• Control how the system responds to and generates 802.3x pause frames on 1 and 10 Gig ports. INTERFACE mode flowcontrol rx [off | on] tx [off | on] – rx on: enter the keywords rx on to process the received flow control frames on this port. – rx off: enter the keywords rx off to ignore the received flow control frames on this port. – tx on: enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received.
For example, the VLAN contains tagged members with Link MTU of 1522 and IP MTU of 1500 and untagged members with Link MTU of 1518 and IP MTU of 1500. The VLAN’s Link MTU cannot be higher than 1518 bytes and its IP MTU cannot be higher than 1500 bytes. Port-Pipes A port pipe is a Dell Networking-specific term for the hardware path that packets follow through a system.
6. Optionally, set full- or half-duplex. INTERFACE mode duplex {half | full} 7. Disable auto-negotiation on the port. INTERFACE mode no negotiation auto If the speed was set to 1000, do not disable auto-negotiation. 8. Verify configuration changes. INTERFACE mode show config Example of the show interfaces status Command to View Link Status NOTE: The show interfaces status command displays link status, but not administrative status.
Example of the negotiation auto Command Dell(conf)# int tengigabitethernet 1/1 Dell(conf-if-te-1/1)#neg auto Dell(conf-if-te-1/1-autoneg)# ? end Exit from configuration mode exit Exit from autoneg configuration mode mode Specify autoneg mode no Negate a command or set its defaults show Show autoneg configuration information Dell(conf-if-te-1/1-autoneg)#mode ? forced-master Force port to master mode forced-slave Force port to slave mode Dell(conf-if-te-1/1-autoneg)# For details about the speed, duplex, and n
Name: TenGigabitEthernet 3/2 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 3/3 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 3/4 802.1QTagged: True Vlan membership: Vlan 2 --More-- Configuring the Interface Sampling Size Although you can enter any value between 30 and 299 seconds (the default), software polling is done once every 15 seconds. So, for example, if you enter “19”, you actually get a sample of the past 15 seconds.
Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 10000 Mbit ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1d23h45m Queueing strategy: fifo 0 packets input, 0 bytes Input 0 IP Packets, 0 Vlans 0 MPLS 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 0 packets output, 0 byte
– For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. – For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. – For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. – For a port channel interface, enter the keywords port-channel then a number. – For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
shut shut shut int te 1/1 int te 1/2 int te 1/3 int te 1/4 int te 1/10 int te 1/34 no ip address no ip address no ip address no ip address no ip address ip address 2.1.1.
! no shutdown interface Vlan 2 ! no ip address no shutdown Compressed config size – 27 lines. ! interface Vlan 3 tagged te 1/1 no ip address shutdown ! interface Vlan 4 tagged te 1/1 no ip address shutdown ! interface Vlan 5 tagged te 1/1 no ip address shutdown ! interface Vlan 100 no ip address no shutdown ! interface Vlan 1000 ip address 1.1.1.
config in flash by default copy compressed-config Copy one file, after optimizing and reducing the size of the configuration file, to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field).
20 IPv4 Routing The Dell Networking Operating System (OS) supports various IP addressing features. This chapter describes the basics of domain name service (DNS), address resolution protocol (ARP), and routing principles and their implementation in the Dell Networking OS. IP Feature Default DNS Disabled Directed Broadcast Disabled Proxy ARP Enabled ICMP Unreachable Disabled ICMP Redirect Disabled IP Addresses Dell Networking OS supports IP version 4, as described in RFC 791.
For a complete listing of all commands related to IP addressing, refer to the Dell Networking OS Command Line Interface Reference Guide. Assigning IP Addresses to an Interface Assign primary and secondary IP addresses to physical or logical (for example, [virtual local area network [VLAN] or port channel) interfaces to enable IP communication between the system and hosts connected to that interface.
ip route [vrf vrf-name] ip-address mask {ip-address | interface [ip-address]} [distance] [permanent] [tag tag-value] [vrf vrf-name] Use the following required and optional parameters: – vrf vrf-name : use the VRF option after the ip route keyword to configure a static route on that particular VRF, use the VRF option after the next hop to specify which VRF the next hop belongs to. This will be used in route leaking cases.
S 6.1.2.15/32 S 6.1.2.16/32 S 6.1.2.17/32 S 11.1.1.0/24 Direct, Lo 0 --More-- via 6.1.20.2, Gi 5/1 via 6.1.20.2, Gi 5/1 via 6.1.20.2, Gi 5/1 Direct, Nu 0 Dell#show ip route static Destination Gateway ----------------S 2.1.2.0/24 Direct, Nu 0 S 6.1.2.0/24 via 6.1.20.2, S 6.1.2.2/32 via 6.1.20.2, S 6.1.2.3/32 via 6.1.20.2, S 6.1.2.4/32 via 6.1.20.2, S 6.1.2.5/32 via 6.1.20.2, S 6.1.2.6/32 via 6.1.20.2, S 6.1.2.7/32 via 6.1.20.2, S 6.1.2.8/32 via 6.1.20.2, S 6.1.2.9/32 via 6.1.20.2, S 6.1.2.10/32 via 6.1.20.
----------10.16.0.0/16 172.16.1.0/24 ------ManagementEthernet 1/1 10.16.151.4 ----Connected Active -----------Connected Static Using the Configured Source IP Address in ICMP Messages This feature is supported on the S6000 platform. ICMP error or unreachable messages are now sent with the configured IP address of the source interface instead of the front-end port IP address as the source IP address. Enable the generation of ICMP unreachable messages through the ip unreachable command in Interface mode.
Enabling Directed Broadcast By default, Dell Networking OS drops directed broadcast packets destined for an interface. This default setting provides some protection against denial of service (DoS) attacks. To enable Dell Networking OS to receive directed broadcasts, use the following command. • Enable directed broadcast. INTERFACE mode ip directed-broadcast To view the configuration, use the show config command in INTERFACE mode.
gxr f00-3 Dell> (perm, OK) (perm, OK) - IP IP 192.71.18.2 192.71.23.1 To view the current configuration, use the show running-config resolve command. Specifying the Local System Domain and a List of Domains If you enter a partial domain, Dell Networking OS can search different domains to finish or fully qualify that partial domain. A fully qualified domain name (FQDN) is any name that is terminated with a period/dot. Dell Networking OS searches the host table first to resolve the partial domain.
---------------------------------------------------------------------Tracing the route to www.force10networks.com (10.11.84.18), 30 hops max, 40 byte packets ---------------------------------------------------------------------TTL Hostname Probe1 Probe2 Probe3 1 10.11.199.190 001.000 ms 001.000 ms 002.000 ms 2 gwegress-sjc-02.force10networks.com (10.11.30.126) 005.000 ms 001.000 ms 001.000 ms 3 fw-sjc-01.force10networks.com (10.11.127.254) 000.000 ms 000.000 ms 000.000 ms 4 www.dell.com (10.11.84.18) 000.
Example of the show arp Command These entries do not age and can only be removed manually. To remove a static ARP entry, use the no arp ip-address command. To view the static entries in the ARP cache, use the show arp static command in EXEC privilege mode. Dell#show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU -------------------------------------------------------------------------------Internet 10.1.2.
• update the ARP table of other nodes on the network in case of an address change In the request, the host uses its own IP address in the Sender Protocol Address and Target Protocol Address fields. In Dell Networking OS versions prior to 8.3.1.0, if a gratuitous ARP is received some time after an ARP request is sent, only RP2 installs the ARP information. For example: 1. At time t=0 Dell Networking OS sends an ARP request for IP A.B.C.D 2.
Figure 43. ARP Learning via ARP Request with ARP Learning via Gratuitous ARP Enabled Whether you enable or disable ARP learning via gratuitous ARP, the system does not look up the target IP. It only updates the ARP entry for the Layer 3 interface with the source IP of the request. Configuring ARP Retries In Dell Networking OS versions prior to 8.3.1.0, the number of ARP retries is set to five and is not configurable.
Configuration Tasks for ICMP The following lists the configuration tasks for ICMP. • Enabling ICMP Unreachable Messages For a complete listing of all commands related to ICMP, refer to the Dell Networking OS Command Line Reference Guide. Enabling ICMP Unreachable Messages By default, ICMP unreachable messages are disabled. When enabled, ICMP unreachable messages are created and sent out all interfaces. To disable and re-enable ICMP unreachable messages, use the following commands.
• Enable UPD helper. ip udp-helper udp-ports Example of Enabling UDP Helper and Using the UDP Helper show Command Dell(conf-if-te-1/1)#ip udp-helper udp-port 1000 Dell(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 ip address 2.1.1.1/24 ip udp-helper udp-port 1000 no shutdown To view the interfaces and ports on which you enabled UDP helper, use the show ip udp-helper command from EXEC Privilege mode.
• UDP Helper with Subnet Broadcast Addresses • UDP Helper with Configured Broadcast Addresses • UDP Helper with No Configured Broadcast Addresses UDP Helper with Broadcast-All Addresses When the destination IP address of an incoming packet is the IP broadcast address, Dell Networking OS rewrites the address to match the configured broadcast address. In the following illustration: 1. Packet 1 is dropped at ingress if you did not configure UDP helper address. 2.
Figure 45. UDP Helper with Subnet Broadcast Addresses UDP Helper with Configured Broadcast Addresses Incoming packets with a destination IP address matching the configured broadcast address of any interface are forwarded to the matching interfaces. In the following illustration, Packet 1 has a destination IP address that matches the configured broadcast address of VLAN 100 and 101.
Troubleshooting UDP Helper To display debugging information for troubleshooting, use the debug ip udp-helper command. Example of the debug ip udp-helper Command Dell(conf)# debug ip udp-helper 01:20:22: Pkt rcvd on Te 5/1 with IP DA (0xffffffff) will be sent on Te 5/2 Te 5/3 Vlan 3 01:44:54: Pkt rcvd on Te 7/1 is handed over for DHCP processing. When using the IP helper and UDP helper on the same interface, use the debug ip dhcp command. Example Output from the debug ip dhcp Command Packet 0.0.0.
21 IPv6 Routing Internet protocol version 6 (IPv6) routing is the successor to IPv4. Due to the rapid growth in internet users and IP addresses, IPv4 is reaching its maximum usage. IPv6 will eventually replace IPv4 usage to allow for the constant expansion. This chapter provides a brief description of the differences between IPv4 and IPv6, and the Dell Networking support of IPv6. This chapter is not intended to be a comprehensive description of IPv6.
Dell Networking OS manipulation of IPv6 stateless autoconfiguration supports the router side only. Neighbor discovery (ND) messages are advertised so the neighbor can use this information to auto-configure its address. However, received ND messages are not used to create an IPv6 address. NOTE: Inconsistencies in router advertisement values between routers are logged per RFC 4861.
On the S6000 platform, for IPv6 /65 to /128 will consume the same storage banks which is used by the L3_DEFIP table. Once the IPv6 128 bit is enabled, number of entries in L3_DEFIP will be reduced. LPM partitioning will take effect after reboot of the box. This is because the SDK does the LPM partitioning during the chip initialization. The longest prefix match (LPM) table on the S6000 platform supports different types of prefixes for IPv6 and IPv4.
Flow Label (20 bits) The Flow Label field identifies packets requiring special treatment in order to manage real-time data traffic. The sending router can label sequences of IPv6 packets so that forwarding routers can process packets within the same flow without needing to reprocess each packet’s header separately. NOTE: All packets in the flow must have the same source and destination addresses. Payload Length (16 bits) The Payload Length field specifies the packet payload.
Source Address (128 bits) The Source Address field contains the IPv6 address for the packet originator. Destination Address (128 bits) The Destination Address field contains the intended recipient’s IPv6 address. This can be either the ultimate destination or the address of the next hop router. Extension Header Fields Extension headers are used only when necessary. Due to the streamlined nature of the IPv6 header, adding extension headers do not severely impact performance.
The third byte specifies whether the information can change en route to the destination. The value is 1 if it can change; the value is 0 if it cannot change. Addressing IPv6 addresses are normally written as eight groups of four hexadecimal digits, where each group is separated by a colon (:). For example, 2001:0db8:0000:0000:0000:0000:1428:57ab is a valid IPv6 address. If one or more four-digit group(s) is 0000, the zeros may be omitted and replaced with two colons(::).
Implementing IPv6 with Dell Networking OS Dell Networking OS supports both IPv4 and IPv6 and both may be used simultaneously in your system. The following table lists the Dell Networking OS version in which an IPv6 feature became available for each platform. The sections following the table give greater detail about the feature. Feature and Functionality Dell Networking OS Release Introduction Documentation and Chapter Location S6000 Basic IPv6 Commands 8.3.
Feature and Functionality Dell Networking OS Release Introduction Documentation and Chapter Location S6000 IPv6 IS-IS in the Dell Networking OS Command Line Reference Guide. ISIS for IPv6 support for distribute lists and administrative distance 8.3.11 OSPF for IPv6 (OSPFv3) 8.3.11 Equal Cost Multipath for IPv6 8.3.11 Intermediate System to Intermediate System IPv6 IS-IS in the Dell Networking OS Command Line Reference Guide. OSPFv3 in the Dell Networking OS Command Line Reference Guide.
• Error reporting messages indicate when the forwarding or delivery of the packet failed at the destination or intermediate node. These messages include Destination Unreachable, Packet Too Big, Time Exceeded and Parameter Problem messages. • Informational messages provide diagnostic functions and additional host functions, such as Neighbor Discovery and Multicast Listener Discovery. These messages also include Echo Request and Echo Reply messages.
Figure 49. NDP Router Redirect IPv6 Neighbor Discovery of MTU Packets You can set the MTU advertised through the RA packets to incoming routers, without altering the actual MTU setting on the interface. The ipv6 nd mtu command sets the value advertised to routers. It does not set the actual MTU rate. For example, if you set ipv6 nd mtu to 1280, the interface still passes 1500-byte packets, if that is what is set with the mtu command.
Dell(conf-if-te-1/1)#ipv6 nd dns-server 1000::1 ? <0-4294967295> Max lifetime (sec) which RDNSS address may be used for name resolution infinite Infinite lifetime (sec) which RDNSS address may be used for name resolution Dell(conf-if-te-1/1)#ipv6 nd dns-server 1000::1 1 Debugging IPv6 RDNSS Information Sent to the Host To verify that the IPv6 RDNSS information sent to the host is configured correctly, use the debug ipv6 nd command in EXEC Privilege mode.
ND advertised hop limit is 64 IPv6 hop limit for originated packets ND dns-server address is 1000::1 with ND dns-server address is 3000::1 with ND dns-server address is 2000::1 with is 64 lifetime of 1 seconds lifetime of 1 seconds lifetime of 0 seconds To display IPv6 RDNSS information, use the show configuration command in INTERFACE CONFIG mode. Dell(conf-if-te-1/1)#show configuration The following example uses the show configuration command to display IPv6 RDNSS information.
To have the changes take effect, save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings. • Allocate space for IPV6 ACLs. Enter the CAM profile name then the allocated amount. CONFIGURATION mode cam-acl { ipv6acl } When not selecting the default option, enter all of the profiles listed and a range for each. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. • Show the current CAM settings.
ipv6 route [vrf vrf-name] prefix type {slot/port} forwarding router tag – vrf vrf-name:(OPTIONAL) name of the VRF. – prefix: IPv6 route prefix – type {slot/port}: interface type and slot/port – forwarding router: forwarding router’s address – tag: route tag Enter the keyword interface then the type of interface and slot/port information: – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
Example of show ipv6 Command Options Dell#show ipv6 ? accounting IPv6 accounting information cam IPv6 CAM Entries fib IPv6 FIB Entries interface IPv6 interface information mbgproutes MBGP routing table mld MLD information mroute IPv6 multicast-routing table neighbors IPv6 neighbor information ospf OSPF information pim PIM V6 information prefix-list List IPv6 prefix lists route IPv6 routing information rpf RPF table Dell# Showing an IPv6 Interface To view the IPv6 configuration for a specific interface, use
ND retransmit interval is 1000 milliseconds ND hop limit is 64 Showing IPv6 Routes To view the global IPv6 routing information, use the following command. • Show IPv6 routing information for the specified route type. EXEC mode show ipv6 route [vrf vrf-name] type The following keywords are available: – To display information about a network, enter ipv6 address (X:X:X:X::X). – To display information about a host, enter hostname.
Dell# Direct, Nu 0, 00:34:42 The following example shows the show ipv6 route static command.
Configuring IPv6 RA Guard The IPv6 Router Advertisement (RA) guard allows you to block or reject the unwanted router advertisement guard messages that arrive at the network device platform. To configure the IPv6 RA guard, perform the following steps: 1. Configure the terminal to enter the Global Configuration mode. EXEC Privilege mode configure terminal 2. Enable the IPv6 RA guard. CONFIGURATION mode ipv6 nd ra-guard enable 3. Create the policy.
router—lifetime value The router lifetime range is from 0 to 9,000 seconds. 11. Apply the policy to trusted ports. POLICY LIST CONFIGURATION mode trusted-port 12. Set the maximum transmission unit (MTU) value. POLICY LIST CONFIGURATION mode mtu value The MTU range is from 1,280 to 11,982 bytes. 13. Set the advertised reachability time. POLICY LIST CONFIGURATION mode reachable—time value The reachability time range is from 0 to 3,600,000 milliseconds. 14. Set the advertised retransmission time.
EXEC Privilege mode show ipv6 nd ra-guard policy policy-name The policy name string can be up to 140 characters. Example of the show ipv6 nd ra-guard policy Command Dell#show ipv6 nd ra-guard policy test ipv6 nd ra-guard policy test device-role router hop-limit maximum 1 match ra ipv6-access-list access other-config-flag on router-preference maximum medium trusted-port Interfaces : Te 1/1 Dell# Monitoring IPv6 RA Guard To debug IPv6 RA guard, use the following command.
22 iSCSI Optimization iSCSI optimization is supported on Dell Networking OS. This chapter describes how to configure internet small computer system interface (iSCSI) optimization, which enables quality-ofservice (QoS) treatment for iSCSI traffic.
switch is configured to use dot1p priority-queue assignments to ensure that iSCSI traffic in these sessions receives priority treatment when forwarded on stacked switch hardware. Figure 50. iSCSI Optimization Example Monitoring iSCSI Traffic Flows The switch snoops iSCSI session-establishment and termination packets by installing classifier rules that trap iSCSI protocol packets to the CPU for examination.
You can configure whether the iSCSI optimization feature uses the VLAN priority or IP DSCP mapping to determine the traffic class queue. By default, iSCSI flows are assigned to dot1p priority 4. To map incoming iSCSI traffic on an interface to a dot1p priority-queue other than 4, use the CoS dot1p-priority command (refer to QoS dot1p Traffic Classification and Queue Assignment). Dell Networking recommends setting the CoS dot1p priority-queue to 0 (zero).
The following message displays the first time a Dell EqualLogic array is detected and describes the configuration changes that are automatically performed: %STKUNIT0-M:CP %IFMGR-5-IFM_ISCSI_AUTO_CONFIG: This switch is being configured for optimal conditions to support iSCSI traffic which will cause some automatic configuration to occur including jumbo frames and flow-control on all ports; no storm control and spanning-tree port fast to be enabled on the port of detection.
Enable and Disable iSCSI Optimization The following describes enabling and disabling iSCSI optimizaiton. NOTE: iSCSI monitoring is disabled by default. iSCSI auto-configuration and auto-detection is enabled by default. If you enable iSCSI, flow control is automatically enabled on all interfaces. To disable flow control on all interfaces, use the no flow control rx on tx off command and save the configuration.
iSCSI Optimization Prerequisites The following are iSCSI optimization prerequisites. • iSCSI optimization requires LLDP on the switch. LLDP is enabled by default (refer to Link Layer Discovery Protocol (LLDP)). • iSCSI optimization requires configuring two ingress ACL groups The ACL groups are allocated after iSCSI Optimization is configured. Configuring iSCSI Optimization To configure iSCSI optimization, use the following commands. 1. For a non-DCB environment: Enable session monitoring.
• tcp-port-n is the TCP port number or a list of TCP port numbers on which the iSCSI target listens to requests. You can configure up to 16 target TCP ports on the switch in one command or multiple commands. The default is 860, 3260. Separate port numbers with a comma. If multiple IP addresses are mapped to a single TCP port, use the no iscsi target port tcp-port-n command to remove all IP addresses assigned to the TCP number.
INTERFACE mode [no] iscsi profile-compellent. The default is: Compellent disk arrays are not detected. Displaying iSCSI Optimization Information To display information on iSCSI optimization, use the following show commands. • • • • Display the currently configured iSCSI settings. show iscsi Display information on active iSCSI sessions on the switch. show iscsi sessions Display detailed information on active iSCSI sessions on the switch .
Up Time:00:00:01:28(DD:HH:MM:SS) Time for aging out:00:00:09:34(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.44 33345 10.10.0.101 3260 0 VLT PEER2 Session 0: ------------------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.
23 Intermediate System to Intermediate System Intermediate system to intermediate system (Is-IS) is supported on Dell Networking OS. • • • • IS-IS is supported on the S6000 with Dell Networking OS 9.0(2.0). The IS-IS protocol is an interior gateway protocol (IGP) that uses a shortest-path-first algorithm. Dell Networking supports both IPv4 and IPv6 versions of IS-IS. The IS-IS protocol standards are listed in the Standards Compliance chapter.
Figure 51. ISO Address Format Multi-Topology IS-IS Multi-topology IS-IS (MT IS-IS) allows you to create multiple IS-IS topologies on a single router with separate databases. Use this feature to place a virtual physical topology into logical routing domains, which can each support different routing and security policies. All routers on a LAN or point-to-point must have at least one common supported topology when operating in Multi-Topology IS-IS mode.
neighbor within its LSPs. The local router does not form an adjacency if both routers do not have at least one common MT over the interface. Graceful Restart Both Helper and Restart modes of Graceful restart are supported on the device. Graceful restart is a protocol-based mechanism that preserves the forwarding table of the restarting router and its neighbors for a specified period to minimize the loss of packets.
• MT Reachable IPv6 Prefixes TLV — appears for each IPv6 an IS announces for a given MT ID. Its structure is aligned with the extended IS Reachability TLV Type 236 and add an MT ID. By default, Dell Networking OS supports dynamic host name exchange to assist with troubleshooting and configuration. By assigning a name to an IS-IS NET address, you can track IS-IS information on that address easier. Dell Networking OS does not support ISO CLNS routing; however, the ISO NET format is supported for addressing.
• Controlling Routing Updates • Configuring Authentication Passwords • Setting the Overload Bit • Debuging IS-IS Enabling IS-IS By default, IS-IS is not enabled. The system supports one instance of IS-IS. To enable IS-IS globally, create an IS-IS routing process and assign a NET address. To exchange protocol information with neighbors, enable IS-IS on an interface, instead of on a network as with other routing protocols. In IS-IS, neighbors form adjacencies only when they are same IS type.
ipv6 address ipv6-address mask • • ipv6 address: x:x:x:x::x mask: The prefix length is from 0 to 128. The IPv6 address must be on the same subnet as other IS-IS neighbors, but the IP address does not need to relate to the NET address. 6. Enable IS-IS on the IPv4 interface. ROUTER ISIS mode ip router isis [tag] If you configure a tag variable, it must be the same as the tag variable assigned in step 1. 7. Enable IS-IS on the IPv6 interface.
IS-IS: IS-IS: IS-IS: IS-IS: Dell# Level-1 SPF Calculations : 29 Level-2 SPF Calculations : 29 LSP checksum errors received : 0 LSP authentication failures : 0 You can assign more NET addresses, but the System ID portion of the NET address must remain the same. Dell Networking OS supports up to six area addresses. Some address considerations are: • In order to be neighbors, configure Level 1 routers with at least one common area address.
ROUTER-ISIS mode graceful-restart interval minutes The range is from 1 to 120 minutes. • The default is 5 minutes. Enable the graceful restart maximum wait time before a restarting peer comes up. ROUTER-ISIS mode graceful-restart restart-wait seconds When implementing this command, be sure to set the t3 timer to adjacency on the restarting router. The range is from 1 to 120 minutes. • The default is 30 seconds.
====================== Graceful Restart Interval/Blackout time T3 Timer T3 Timeout Value T2 Timeout Value T1 Timeout Value Adjacency wait time : : : : : : : Operational Timer Value ====================== Current Mode/State : T3 Time left : T2 Time left : Restart ACK rcv count : Restart Req rcv count : Suppress Adj rcv count : Restart CSNP rcv count : Database Sync count : Enabled 1 min Manual 30 30 (level-1), 30 (level-2) 5, retry count: 1 30 Normal/RUNNING 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0
The default is 5 seconds. • The default level is Level 1. Set the LSP size. ROUTER ISIS mode lsp-mtu size – size: the range is from 128 to 9195. • The default is 1497. Set the LSP refresh interval. ROUTER ISIS mode lsp-refresh-interval seconds – seconds: the range is from 1 to 65535. • The default is 900 seconds. Set the maximum time LSPs lifetime. ROUTER ISIS mode max-lsp-lifetime seconds – seconds: the range is from 1 to 65535. The default is 1200 seconds.
Table 35. Metric Styles Metric Style Characteristics Cost Range Supported on IS-IS Interfaces narrow Sends and accepts narrow or old TLVs (Type, Length, Value). 0 to 63 wide Sends and accepts wide or new TLVs. 0 to 16777215 transition Sends both wide (new) and narrow (old) TLVs. 0 to 63 narrow transition Sends narrow (old) TLVs and accepts both narrow (old) and wide (new) TLVs. 0 to 63 wide transition Sends wide (new) TLVs and accepts both narrow (old) and wide (new) TLVs.
– default-metric: the range is from 0 to 63 if the metric-style is narrow, narrow-transition, or transition. • The range is from 0 to 16777215 if the metric style is wide or wide transition. Assign a metric for an IPv6 link or interface. INTERFACE mode isis ipv6 metric default-metric [level-1 | level-2] – default-metric: the range is from 0 to 63 for narrow and transition metric styles. The range is from 0 to 16777215 for wide metric styles. The default is 10. The default level is level-1.
Example of the show isis database Command to View Level 1-2 Link State Databases To view which IS-type is configured, use the show isis protocol command in EXEC Privilege mode. The show config command in ROUTER ISIS mode displays only non-default information. If you do not change the IS-type, the default value (level-1-2) is not displayed. The default is Level 1-2 router. When the IS-type is Level 1-2, the software maintains two Link State databases, one for each level.
Enter the type of interface and slot/port information: – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. – For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. – For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. – For a port channel interface, enter the keywords port-channel then a number. • – For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
– static: for user-configured routes. – bgp: for BGP routes only. • Deny RTM download for pre-existing redistributed IPv6 routes. ROUTER ISIS-AF IPV6 mode distribute-list redistributed-override in Redistributing IPv4 Routes In addition to filtering routes, you can add routes from other routing instances or protocols to the IS-IS process. With the redistribute command syntax, you can include BGP, OSPF, RIP, static, or directly connected routes in the IS-IS process.
redistribute {bgp as-number | connected | rip | static} [level-1 level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] Configure the following parameters: – level-1, level-1-2, or level-2: assign all redistributed routes to a level. The default is level-2. – metric-value: the range is from 0 to 16777215. The default is 0. – metric-type: choose either external or internal. The default is internal. • – map-name: enter the name of a configured route map.
To remove a password, use either the no area-password or no domain-password commands in ROUTER ISIS mode. Setting the Overload Bit Another use for the overload bit is to prevent other routers from using this router as an intermediate hop in their shortest path first (SPF) calculations. For example, if the IS-IS routing database is out of memory and cannot accept new LSPs, Dell Networking OS sets the overload bit and IS-IS traffic continues to transit the system.
To view specific information, enter the following optional parameter: – interface: Enter the type of interface and slot/port information to view IS-IS information on that interface only. • View IS-IS SNP packets, include CSNPs and PSNPs. EXEC Privilege mode debug isis snp-packets [interface] To view specific information, enter the following optional parameter: – interface: Enter the type of interface and slot/port information to view IS-IS information on that interface only.
Metric Style Correct Value Range for the isis metric Command wide 0 to 16777215 narrow 0 to 63 wide transition 0 to 16777215 narrow transition 0 to 63 transition 0 to 63 Maximum Values in the Routing Table IS-IS metric styles support different cost ranges for the route. The cost range for the narrow metric style is 0 to 1023, while all other metric styles support a range of 0 to 0xFE000000. Change the IS-IS Metric Style in One Level Only By default, the IS-IS metric style is narrow.
Beginning Metric Style Final Metric Style Resulting IS-IS Metric Value narrow transition wide original value narrow transition narrow original value narrow transition wide transition original value narrow transition transition original value wide transition wide original value wide transition narrow default value (10) if the original value is greater than 63. A message is sent to the console.
Level-1 Metric Style Level-2 Metric Style Resulting Metric Value wide wide transition original value wide transition truncated value narrow transition wide original value narrow transition narrow original value narrow transition wide transition original value narrow transition transition original value transition wide original value transition narrow original value transition wide transition original value transition narrow transition original value wide transition wide or
Figure 52. IPv6 IS-IS Sample Topography IS-IS Sample Configuration — Congruent Topology IS-IS Sample Configuration — Multi-topology IS-IS Sample Configuration — Multi-topology Transition The following is a sample configuration for enabling IPv6 IS-IS. Dell(conf-if-te-3/17)#show config ! interface TenGigabitEthernet 3/17 ip address 24.3.1.
exit-address-family Dell (conf-router_isis)# Dell (conf-if-te-3/17)#show config ! interface TenGigabitEthernet 3/17 ipv6 address 24:3::1/76 ipv6 router isis no shutdown Dell (conf-if-te-3/17)# Dell (conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.
24 Link Aggregation Control Protocol (LACP) Link aggregation control protocol (LACP) is supported on Dell Networking OS. Introduction to Dynamic LAGs and LACP A link aggregation group (LAG), referred to as a port channel by Dell Networking OS, can provide both load-sharing and port redundancy across line cards. You can enable LAGs as static or dynamic. The benefits and constraints are basically the same, as described in Port Channel Interfaces in the Interfaces chapter.
• You can configure a maximum of 128 port-channels with up to 16 members per channel. LACP Modes Dell Networking OS provides three modes for configuration of LACP — Off, Active, and Passive. • Off — In this state, an interface is not capable of being part of a dynamic LAG. LACP does not run on any port that is configured to be in this state. • Active — In this state, the interface is said to be in the “active negotiating state.” LACP runs on any link that is configured to be in this state.
LACP Configuration Tasks The following are LACP configuration tasks. • Creating a LAG • Configuring the LAG Interfaces as Dynamic • Setting the LACP Long Timeout • Monitoring and Debugging LACP • Configuring Shared LAG State Tracking Creating a LAG To create a dynamic port channel (LAG), use the following command. First you define the LAG and then the LAG interfaces. • Create a dynamic port channel (LAG). CONFIGURATION mode • interface port-channel Create a dynamic port channel (LAG).
Dell(conf)#interface Gigabitethernet 4/16 Dell(conf-if-gi-4/16)#no shutdown Dell(conf-if-gi-4/16)#port-channel-protocol lacp Dell(conf-if-gi-4/16-lacp)#port-channel 32 mode active The port-channel 32 mode active command shown here may be successfully issued as long as there is no existing static channelmember configuration in LAG 32. Setting the LACP Long Timeout PDUs are exchanged between port channel (LAG) interfaces to maintain LACP sessions.
Shared LAG State Tracking Shared LAG state tracking provides the flexibility to bring down a port channel (LAG) based on the operational state of another LAG. At any time, only two LAGs can be a part of a group such that the fate (status) of one LAG depends on the other LAG. As shown in the following illustration, the line-rate traffic from R1 destined for R4 follows the lowest-cost route via R2. Traffic is equally distributed between LAGs 1 and 2.
As shown in the following illustration, LAGs 1 and 2 are members of a failover group. LAG 1 fails and LAG 2 is brought down after the failure. This effect is logged by Message 1, in which a console message declares both LAGs down at the same time. Figure 54.
LACP Basic Configuration Example The screenshots in this section are based on the following example topology. Two routers are named ALPHA and BRAVO, and their hostname prompts reflect those names. Figure 55. LACP Basic Configuration Example Configure a LAG on ALPHA The following example creates a LAG on ALPHA.
0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics 136 packets, 16718 bytes, 0 underruns 0 64-byte pkts, 15 over 64-byte pkts, 121 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 136 Multicasts, 0 Broadcasts, 0 Unicasts 0 Vlans, 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec,0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec,0 packets/sec, 0.
Figure 57.
Figure 58.
Bravo(conf-if-po-10)#switch Bravo(conf-if-po-10)#no shut Bravo(conf-if-po-10)#show config ! interface Port-channel 10 no ip address switchport no shutdown ! Bravo(conf-if-po-10)#exit Bravo(conf)#int gig 3/21 Bravo(conf)#no ip address Bravo(conf)#no switchport Bravo(conf)#shutdown Bravo(conf-if-gi-3/21)#port-channel-protocol lacp Bravo(conf-if-gi-3/21-lacp)#port-channel 10 mode active Bravo(conf-if-gi-3/21-lacp)#no shut Bravo(conf-if-gi-3/21)#end ! interface GigabitEthernet 3/21 no ip address ! port-channel-
Figure 59.
Figure 60.
Figure 61. Inspecting the LAG Status Using the show lacp command The point-to-point protocol (PPP) is a connection-oriented protocol that enables layer two links over various different physical layer connections. It is supported on both synchronous and asynchronous lines, and can operate in Half-Duplex or Full-Duplex mode. It was designed to carry IP traffic but is general enough to allow any type of network layer datagram to be sent over a PPP connection.
25 Layer 2 Layer 2 features are supported on Dell Networking OS. Manage the MAC Address Table Dell Networking OS provides the following management activities for the MAC address table. • Clearing the MAC Address Table • Setting the Aging Time for Dynamic Entries • Configuring a Static MAC Address • Displaying the MAC Address Table Clearing the MAC Address Table You may clear the MAC address table of dynamic entries. To clear a MAC address table, use the following command.
• Create a static MAC address entry in the MAC address table. CONFIGURATION mode mac-address-table static Displaying the MAC Address Table To display the MAC address table, use the following command. • Display the contents of the MAC address table. EXEC Privilege mode show mac-address-table [address | aging-time [vlan vlan-id]| count | dynamic | interface | static | vlan] – address: displays the specified entry. – aging-time: displays the configured aging-time.
Setting the MAC Learning Limit To set a MAC learning limit on an interface, use the following command. • Specify the number of MAC addresses that the system can learn off a Layer 2 interface. INTERFACE mode mac learning-limit address_limit Three options are available with the mac learning-limit command: – dynamic – no-station-move – station-move NOTE: An SNMP trap is available for mac learning-limit station-move. No other SNMP traps are available for MAC Learning Limit, including limit violations.
mac learning-limit no-station-move The no-station-move option, also known as “sticky MAC,” provides additional port security by preventing a station move. When you configure this option, the first entry in the table is maintained instead of creating an entry on the new interface. nostation-move is the default behavior. Entries created before you set this option are not affected. To display a list of all interfaces with a MAC learning limit, use the following command.
station-move-violation shutdown-offending • Shut down both the first and second port to learn the MAC address. INTERFACE mode station-move-violation shutdown-both • Display a list of all of the interfaces configured with MAC learning limit or station move violation. CONFIGURATION mode show mac learning-limit violate-action NOTE: When the MAC learning limit (MLL) is configured as no-station-move, the MLL will be processed as static entries internally.
Figure 62. Redundant NICs with NIC Teaming When you use NIC teaming, consider that the server MAC address is originally learned on Port 0/1 of the switch (shown in the following) and Port 0/5 is the failover port. When the NIC fails, the system automatically sends an ARP request for the gateway or host NIC to resolve the ARP and refresh the egress interface.
(as shown in the following illustration). The redundant pairs feature allows you to create redundant links in networks that do not use STP by configuring backup interfaces for the interfaces on either side of the primary link. NOTE: For more information about STP, refer to Spanning Tree Protocol (STP). Assign a backup interface to an interface using the switchport backup command. The backup interface remains in a Down state until the primary fails, at which point it transitions to Up state.
In a redundant pair, any combination of physical and port-channel interfaces is supported as the two interfaces in a redundant pair. For example, you can configure a static (without LACP) or dynamic (with LACP) port-channel interface as either the primary or backup link in a redundant pair with a physical interface.
LAG Mode Status Uptime Ports 1 L2 up 00:08:33 Te 1/1 (Up) 2 L2 up 00:00:02 Te 2/1 (Up) Dell#configure Dell(conf)#interface port-channel 1 Dell(conf-if-po-1)#switchport backup interface port-channel 2 Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Po 2 Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 2 Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-STATE_ACT_STBY: Changed interface state to standby: Po 2 Dell(conf-if-po-1)# Dell
The report consists of several packets in SNAP format that are sent to the nearest known MAC address. In the event of a far-end failure, the device stops receiving frames and, after the specified time interval, assumes that the far-end is not available. The connecting line protocol is brought down so that upper layer protocols can detect the neighbor unavailability faster. FEFD State Changes FEFD has two operational modes, Normal and Aggressive.
• Enable FEFD globally on all interfaces. CONFIGURATION mode fefd-global To report interval frequency and mode adjustments, use the following commands. 1. Setup two or more connected interfaces for Layer 2 or Layer 3. INTERFACE mode ip address ip address, switchport 2. Activate the necessary ports administratively. INTEFACE mode no shutdown 3. Enable fefd globally.
To set up and activate two or more connected interfaces, use the following commands. 1. Setup two or more connected interfaces for Layer 2 or Layer 3. INTERFACE mode ip address ip address, switchport 2. Activate the necessary ports administratively. INTERFACE mode no shutdown 3.
Sender info -- Mgmt Mac(00:01:e8:14:89:25), Slot-Port(Te 1/1) Peer info -- Mgmt Mac (00:01:e8:14:89:25), Slot-Port(Te 4/1) Sender hold time -- 3 (second) An RPM Failover In the event that an RPM failover occurs, FEFD becomes operationally down on all enabled ports for approximately 8-10 seconds before automatically becoming operational again. 02-05-2009 12:40:38 Local7.Debug 10.16.151.12 Feb 5 07:06:09: %RPM1-S:CP %RAM-6-FAILOVER_REQ: RPM failover request from active peer: User request.
26 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) is supported on Dell Networking OS. 802.1AB (LLDP) Overview LLDP — defined by IEEE 802.1AB — is a protocol that enables a local area network (LAN) device to advertise its configuration and receive configuration information from adjacent LLDP-enabled LAN infrastructure devices.
Type TLV Description 2 Port ID An administratively assigned name that identifies a port through which TLVs are sent and received. 3 Time to Live An administratively assigned name that identifies a port through which TLVs are sent and received. — Optional Includes sub-types of TLVs that advertise specific configuration information. These sub-types are Management TLVs, IEEE 802.1, IEEE 802.3, and TIA-1057 Organizationally Specific TLVs. Figure 67.
IEEE Organizationally Specific TLVs Eight TLV types have been defined by the IEEE 802.1 and 802.3 working groups as a basic part of LLDP; the IEEE OUI is 00-80-C2. You can configure the Dell Networking system to advertise any or all of these TLVs. Table 41. Optional TLV Types Type TLV Description 4 Port description A user-defined alphanumeric string that describes the port. Dell Networking OS does not currently support this TLV.
Type TLV Description 127 Link Aggregation Indicates whether the link is capable of being aggregated, whether it is currently in a LAG, and the port identification of the LAG. Dell Networking OS does not currently support this TLV. 127 Maximum Frame Size Indicates the maximum frame size capability of the MAC and PHY.
Type SubType TLV Description 127 3 Location Identification Indicates that the physical location of the device expressed in one of three possible formats: • • • 127 4 Inventory Management TLVs Implementation of this set of TLVs is optional in LLDP-MED devices. None or all TLVs must be supported. Dell Networking OS does not currently support these TLVs.
Figure 69. LLDP-MED Capabilities TLV Table 43. Dell Networking OS LLDP-MED Capabilities Bit Position TLV Dell Networking OS Support 0 LLDP-MED Capabilities Yes 1 Network Policy Yes 2 Location Identification Yes 3 Extended Power via MDI-PSE Yes 4 Extended Power via MDI-PD No 5 Inventory No 6–15 reserved No Table 44.
Table 45. Network Policy Applications Type Application Description 0 Reserved — 1 Voice Specify this application type for dedicated IP telephony handsets and other appliances supporting interactive voice services. 2 Voice Signaling Specify this application type only if voice control packets use a separate network policy than voice data.
Figure 71. Extended Power via MDI TLV Configure LLDP Configuring LLDP is a two-step process. 1. Enable LLDP globally. 2. Advertise TLVs out of an interface. Related Configuration Tasks • Viewing the LLDP Configuration • Viewing Information Advertised by Adjacent LLDP Agents • Configuring LLDPDU Intervals • Configuring Transmit and Receive Mode • Configuring a Time to Live • Debugging LLDP Important Points to Remember • LLDP is enabled by default.
multiplier no show LLDP multiplier configuration Negate a command or set its defaults Show LLDP configuration Dell(conf-lldp)#exit Dell(conf)#interface tengigabitethernet 1/3 Dell(conf-if-te-1/3)#protocol lldp Dell(conf-if-te-1/3-lldp)#? advertise Advertise TLVs disable Disable LLDP protocol on this interface end Exit from configuration mode exit Exit from LLDP configuration mode hello LLDP hello configuration mode LLDP mode configuration (default = rx and tx) multiplier LLDP multiplier configuration no N
Disabling and Undoing LLDP on Management Ports To disable or undo LLDP on management ports, use the following command. 1. Enter Protocol LLDP mode. CONFIGURATION mode. protocol lldp 2. Enter LLDP management-interface mode. LLDP-MANAGEMENT-INTERFACE mode. management-interface 3. Enter the disable command. LLDP-MANAGEMENT-INTERFACE mode. To undo an LLDP management port configuration, precede the relevant command with the keyword no.
– voice – voice-signaling In the following example, LLDP is enabled globally. R1 and R2 are transmitting periodic LLDPDUs that contain management, 802.1, and 802.3 TLVs. Figure 72. Configuring LLDP Viewing the LLDP Configuration To view the LLDP configuration, use the following command. • Display the LLDP configuration.
Viewing Information Advertised by Adjacent LLDP Agents To view brief information about adjacent devices or to view all the information that neighbors are advertising, use the following commands. • • Display brief information about adjacent devices. show lldp neighbors Display all of the information that neighbors are advertising.
• Configure a non-default transmit interval.
advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)#mode ? rx Rx only tx Tx only R1(conf-lldp)#mode tx R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description mode tx no disable R1(conf-lldp)#no mode R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size adverti
no disable R1(conf-lldp)# Debugging LLDP You can view the TLVs that your system is sending and receiving. To view the TLVs, use the following commands. • View a readable version of the TLVs. debug lldp brief • View a readable version of the TLVs plus a hexadecimal version of the entire LLDPDU. debug lldp detail Figure 73. The debug lldp detail Command — LLDPDU Packet Dissection Relevant Management Objects Dell Networking OS supports all IEEE 802.1AB MIB objects.
Table 46. LLDP Configuration MIB Objects MIB Object Category LLDP Variable LLDP MIB Object Description LLDP Configuration adminStatus lldpPortConfigAdminStatus Whether you enable the local LLDP agent for transmit, receive, or both. msgTxHold lldpMessageTxHoldMultiplier Multiplier value. msgTxInterval lldpMessageTxInterval Transmit Interval value. rxInfoTTL lldpRxInfoTTL Time to live for received TLVs. txInfoTTL lldpTxInfoTTL Time to live for transmitted TLVs.
TLV Type TLV Name TLV Variable System LLDP MIB Object 4 Port Description port description Local lldpLocPortDesc Remote lldpRemPortDesc Local lldpLocSysName Remote lldpRemSysName Local lldpLocSysDesc Remote lldpRemSysDesc Local lldpLocSysCapSupported Remote lldpRemSysCapSupported Local lldpLocSysCapEnabled Remote lldpRemSysCapEnabled Local lldpLocManAddrLen Remote lldpRemManAddrLen Local lldpLocManAddrSubtype Remote lldpRemManAddrSubtype Local lldpLocManAddr Remote lldp
TLV Type 127 TLV Name VLAN Name TLV Variable System LLDP MIB Object PPVID Local lldpXdot1LocProtoVlanId Remote lldpXdot1RemProtoVlanId Local lldpXdot1LocVlanId Remote lldpXdot1RemVlanId Local lldpXdot1LocVlanName Remote lldpXdot1RemVlanName Local lldpXdot1LocVlanName Remote lldpXdot1RemVlanName VID VLAN name length VLAN name Table 49.
TLV Sub-Type TLV Name TLV Variable DSCP Value 3 Location Identifier Location Data Format Location ID Data 4 Extended Power via MDI Power Device Type Power Source System LLDP-MED MIB Object Remote lldpXMedRemMediaPolicy Priority Local lldpXMedLocMediaPolicy Dscp Remote lldpXMedRemMediaPolicy Dscp Local lldpXMedLocLocationSubt ype Remote lldpXMedRemLocationSub type Local lldpXMedLocLocationInfo Remote lldpXMedRemLocationInfo Local lldpXMedLocXPoEDevice Type Remote lldpXMedRemXPo
27 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems (OSs). NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
In Multicast NLB mode, configure a static ARP configuration command to associate the cluster IP address with a multicast cluster MAC address.
Configuring a Switch for NLB To enable a switch for Unicast NLB mode, perform the following steps: Enter the ip vlan-flooding command to specify that all Layer 3 unicast routed data traffic going through a VLAN member port floods across all the member ports of that VLAN. CONFIGURATION mode ip vlan-flooding There might be some ARP table entries that are resolved through ARP packets, which had the Ethernet MAC SA different from the MAC information inside the ARP packet.
28 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) is supported on Dell Networking OS. Protocol Overview MSDP is a Layer 3 protocol that connects IPv4 protocol-independent multicast-sparse mode (PIM-SM) domains. A domain in the context of MSDP is a contiguous set of routers operating PIM within a common boundary defined by an exterior gateway protocol, such as border gateway protocol (BGP).
Figure 75. MSDP SA Message Format Anycast RP Using MSDP, anycast RP provides load sharing and redundancy in PIM-SM networks. Anycast RP allows two or more rendezvous points (RPs) to share the load for source registration and the ability to act as hot backup routers for each other. Anycast RP allows you to configure two or more RPs with the same IP address on Loopback interfaces. The Anycast RP Loopback address are configured with a 32-bit mask, making it a host address.
3. Enable MSDP. 4. Peer the RPs in each routing domain with each other. Refer to Enable MSDP. Related Configuration Tasks The following lists related MSDP configuration tasks.
Figure 76.
Figure 77.
Figure 78.
Figure 79. Configuring MSDP Enable MSDP Enable MSDP by peering RPs in different administrative domains. 1. Enable MSDP. CONFIGURATION mode ip multicast-msdp 2. Peer PIM systems in different administrative domains. CONFIGURATION mode ip msdp peer connect-source Examples of Configuring and Viewing MSDP R3_E600(conf)#ip multicast-msdp R3_E600(conf)#ip msdp peer 192.168.0.
Peer Addr Description Local Addr State Source SA Up/Down To view details about a peer, use the show ip msdp peer command in EXEC privilege mode. Multicast sources in remote domains are stored on the RP in the source-active cache (SA cache). The system does not create entries in the multicast routing table until there is a local receiver for the corresponding multicast group. R3_E600#show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.
If the total number of active sources is already larger than the limit when limiting is applied, the sources that are already in Dell Networking OS are not discarded. To enforce the limit in such a situation, use the clear ip msdp sa-cache command to clear all existing entries. Clearing the Source-Active Cache To clear the source-active cache, use the following command. • Clear the SA cache of all, local, or rejected entries, or entries for a specific group.
Figure 80.
Figure 81.
Figure 82.
Figure 83. MSDP Default Peer, Scenario 4 Specifying Source-Active Messages To specify messages, use the following command. • Specify the forwarding-peer and originating-RP from which all active sources are accepted without regard for the RPF check. CONFIGURATION mode ip msdp default-peer ip-address list If you do not specify an access list, the peer accepts all sources that peer advertises. All sources from RPs that the ACL denies are subject to the normal RPF check.
GroupAddr 229.0.50.2 229.0.50.3 229.0.50.4 SourceAddr 24.0.50.2 24.0.50.3 24.0.50.4 RPAddr 200.0.0.50 200.0.0.50 200.0.0.50 LearnedFrom 10.0.50.2 10.0.50.2 10.0.50.2 Dell#ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 3 rejected SAs received, cache-size 32766 UpTime GroupAddr SourceAddr RPAddr 00:33:18 229.0.50.64 24.0.50.64 200.0.1.50 00:33:18 229.0.50.65 24.0.50.65 200.0.1.50 00:33:18 229.0.50.66 24.0.50.66 200.0.1.50 Expire 73 73 73 UpTime 00:13:49 00:13:49 00:13:49 LearnedFrom 10.0.50.2 10.
seq 10 deny ip any any R1_E600(conf)#do show ip msdp sa-cache R1_E600(conf)#do show ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 1 rejected SAs received, cache-size 1000 UpTime GroupAddr SourceAddr RPAddr LearnedFrom 00:02:20 239.0.0.1 10.11.4.2 192.168.0.1 local Reason Redistribute Preventing MSDP from Caching a Remote Source To prevent MSDP from caching a remote source, use the following commands. 1. OPTIONAL: Cache sources that the SA filter denies in the rejected SA cache.
Example of Verifying the System is not Advertising Local Sources In the following example, R1 stops advertising source 10.11.4.2. Because it is already in the SA cache of R3, the entry remains there until it expires. [Router 1] R1_E600(conf)#do show run msdp ! ip multicast-msdp ip msdp peer 192.168.0.3 connect-source Loopback 0 ip msdp sa-filter out 192.168.0.3 list mylocalfilter R1_E600(conf)#do show run acl ! ip access-list extended mylocalfilter seq 5 deny ip host 239.0.0.1 host 10.11.4.
SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: myremotefilter Output (S,G) filter: none [Router 1] R1_E600(conf)#do show ip msdp peer Peer Addr: 192.168.0.3 Local Addr: 0.0.0.0(0) Connect Source: Lo 0 State: Inactive Up/Down Time: 00:00:03 Timers: KeepAlive 30 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learned from this peer: 0 SA Filtering: Clearing Peer Statistics To clear the peer statistics, use the following command.
03:16:09 : MSDP-0: Peer 192.168.0.3, 03:16:27 : MSDP-0: Peer 192.168.0.3, 03:16:38 : MSDP-0: Peer 192.168.0.3, 03:16:39 : MSDP-0: Peer 192.168.0.3, 03:17:09 : MSDP-0: Peer 192.168.0.3, 03:17:10 : MSDP-0: Peer 192.168.0.3, 03:17:27 : MSDP-0: Peer 192.168.0.
Figure 84. MSDP with Anycast RP Configuring Anycast RP To configure anycast RP, use the following commands. 1. In each routing domain that has multiple RPs serving a group, create a Loopback interface on each RP serving the group with the same IP address. CONFIGURATION mode interface loopback 2. Make this address the RP for the group. CONFIGURATION mode ip pim rp-address 3.
CONFIGURATION mode ip msdp peer 5. Advertise the network of each of the unique Loopback addresses throughout the network. ROUTER OSPF mode network Reducing Source-Active Message Flooding RPs flood source-active messages to all of their peers away from the RP. When multiple RPs exist within a domain, the RPs forward received active source information back to the originating RP, which violates the RFP rule. You can prevent this unnecessary flooding by creating a mesh-group.
network 10.11.1.0/24 area 0 network 10.11.3.0/24 area 0 network 192.168.0.11/32 area 0 ! ip ip ip ip ip multicast-msdp msdp peer 192.168.0.3 connect-source Loopback 1 msdp peer 192.168.0.22 connect-source Loopback 1 msdp mesh-group AS100 192.168.0.22 msdp originator-id Loopback 1! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 The following example shows an R2 configuration for MSDP with Anycast RP. ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.
ip pim sparse-mode ip address 10.11.0.32/24 no shutdown interface TenGigabitEthernet 3/41 ip pim sparse-mode ip address 10.11.6.34/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.3/32 no shutdown ! router ospf 1 network 10.11.6.0/24 area 0 network 192.168.0.3/32 area 0 redistribute static redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.22 remote-as 100 neighbor 192.168.0.22 ebgp-multihop 255 neighbor 192.168.0.
ip ip ip ip ! ip ip ! ip multicast-msdp msdp peer 192.168.0.11 connect-source Loopback 0 msdp peer 192.168.0.22 connect-source Loopback 0 msdp sa-filter out 192.168.0.22 route 192.168.0.1/32 10.11.0.23 route 192.168.0.22/32 10.11.0.23 pim rp-address 192.168.0.3 group-address 224.0.0.0/4 MSDP Sample Configurations The following examples show the running-configurations described in this chapter. For more information, refer to the illustrations in the Related Configuration Tasks section.
interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.0.23/24 no shutdown ! interface Loopback 0 ip address 192.168.0.2/32 no shutdown ! router ospf 1 network 10.11.1.0/24 area 0 network 10.11.4.0/24 area 0 network 192.168.0.2/32 area 0 redistribute static redistribute connected redistribute bgp 100 ! router bgp 100 redistribute ospf 1 neighbor 192.168.0.3 remote-as 200 neighbor 192.168.0.3 ebgp-multihop 255 neighbor 192.168.0.3 update-source Loopback 0 neighbor 192.168.0.
ip multicast-routing ! interface TenGigabitEthernet 4/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown ! interface TenGigabitEthernet 4/22 ip address 10.10.42.1/24 no shutdown ! interface TenGigabitEthernet 4/31 ip pim sparse-mode ip address 10.11.6.43/24 no shutdown ! interface Loopback 0 ip address 192.168.0.4/32 no shutdown ! router ospf 1 network 10.11.5.0/24 area 0 network 10.11.6.0/24 area 0 network 192.168.0.4/32 area 0 ! ip pim rp-address 192.168.0.3 group-address 224.0.0.
29 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP) is supported on Dell Networking OS. Protocol Overview MSTP — specified in IEEE 802.1Q-2003 — is a rapid spanning tree protocol (RSTP)-based spanning tree variation that improves on per-VLAN spanning tree plus (PVST+). MSTP allows multiple spanning tree instances and allows you to map many VLANs to one spanning tree instance to reduce the total number of required instances.
Spanning Tree Variations The Dell Networking OS supports four variations of spanning tree, as shown in the following table. Table 50. Spanning Tree Variations Dell Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .1w Multiple Spanning Tree Protocol (MSTP) 802 .1s Per-VLAN Spanning Tree Plus (PVST+) Third Party Implementation Information The following describes the MSTP implementation information.
Enable Multiple Spanning Tree Globally MSTP is not enabled by default. To enable MSTP globally, use the following commands. When you enable MSTP, all physical, VLAN, and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the MSTI 0. • Within an MSTI, only one path from any bridge to any other bridge is enabled. • Bridges block a redundant path by disabling one of the link ports. 1. Enter PROTOCOL MSTP mode. CONFIGURATION mode protocol spanning-tree mstp 2.
Dell(conf-mstp)#msti 2 vlan 200-300 Dell(conf-mstp)#show config ! protocol spanning-tree mstp no disable MSTI 1 VLAN 100 MSTI 2 VLAN 200-300 All bridges in the MSTP region must have the same VLAN-to-instance mapping. To view which instance a VLAN is mapped to, use the show spanning-tree mst vlan command from EXEC Privilege mode.
The range is from 0 to 61440, in increments of 4096. The default is 32768. Example of Assigning and Verifying the Root Bridge Priority By default, the simple configuration shown previously yields the same forwarding path for both MSTIs. The following example shows how R3 is assigned bridge priority 0 for MSTI 2, which elects a different root bridge than MSTI 2. To view the bridge priority, use the show config command from PROTOCOL MSTP mode.
MST region name: my-mstp-region Revision: 0 MSTI VID 1 100 2 200-300 Modifying Global Parameters The root bridge sets the values for forward-delay, hello-time, max-age, and max-hops and overwrites the values set on other MSTP bridges. • Forward-delay — the amount of time an interface waits in the Listening state and the Learning state before it transitions to the Forwarding state. • Hello-time — the time interval in which the bridge sends MSTP bridge protocol data units (BPDUs).
Example of the forward-delay Parameter To view the current values for MSTP parameters, use the show running-config spanning-tree mstp command from EXEC privilege mode.
To view the current values for these interface parameters, use the show config command from INTERFACE mode. Configuring an EdgePort The EdgePort feature enables interfaces to begin forwarding traffic approximately 30 seconds sooner. In this mode, an interface forwards frames by default until it receives a BPDU that indicates that it should behave otherwise; it does not go through the Learning and Listening states.
To view the enable status of this feature, use the show running-config spanning-tree mstp command from EXEC Privilege mode. MSTP Sample Configurations The running-configurations support the topology shown in the following illustration. The configurations are from Dell Networking OS systems. Figure 86. MSTP with Three VLANs Mapped to Two Spanning Tree Instances Router 1 Running-Configuration This example uses the following steps: 1.
! interface Vlan 200 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown Router 2 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3. Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
MSTI 1 VLAN 100 MSTI 2 VLAN 200,300 ! (Step 2) interface TenGigabitEthernet 3/11 no ip address switchport no shutdown ! interface TenGigabitEthernet 3/21 no ip address switchport no shutdown ! (Step 3) interface Vlan 100 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 3/11,21 no shutdown SFTOS Example Running-Configuration This example uses the following
tagged 1/0/31 tagged 1/0/32 exit interface vlan 300 tagged 1/0/31 tagged 1/0/32 exit Debugging and Verifying MSTP Configurations To debut and verify MSTP configuration, use the following commands. • Display BPDUs. EXEC Privilege mode debug spanning-tree mstp bpdu • Display MSTP-triggered topology change messages.
The following example shows viewing the debug log of a successful MSTP configuration. Dell#debug spanning-tree mstp bpdu MSTP debug bpdu is ON Dell# 4w0d4h : MSTP: Sending BPDU on Te 2/21 : ProtId: 0, Ver: 3, Bpdu Type: MSTP, Flags 0x6e CIST Root Bridge Id: 32768:0001.e806.953e, Ext Path Cost: 0 Regional Bridge Id: 32768:0001.e806.
30 Multicast Features NOTE: Multicast routing is supported on secondary IP addresses; it is not supported on IPv6. NOTE: Multicast routing is supported across default and non-default VRFs. The Dell Networking operating system (OS) supports the following multicast protocols: • PIM Sparse-Mode (PIM-SM) • Internet Group Management Protocol (IGMP) • Multicast Source Discovery Protocol (MSDP) Enabling IP Multicast Prior to enabling any multicast protocols, you must enable multicast routing.
• Multicast is not supported on secondary IP addresses. • If you enable multicast routing, Egress L3 ACL is not applied to multicast data traffic. Multicast Policies Dell Networking OS offers parallel multicast features for IPv4. IPv4 Multicast Policies The following sections describe IPv4 multicast policies.
Preventing a Host from Joining a Group You can prevent a host from joining a particular group by blocking specific IGMP reports. Create an extended access list containing the permissible source-group pairs. NOTE: For rules in IGMP access lists, source is the multicast source, not the source of the IGMP packet. For IGMPv2, use the keyword any for source (as shown in the following example) because the IGMPv2 hosts do not know in advance who the source is for the group in which they are interested.
Figure 87. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 52. Preventing a Host from Joining a Group — Description Location Description 1/21 • • • • Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • • Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Location Description • • ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 • • • • Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
Setting a Threshold for Switching to the SPT The functionality to specify a threshold for switchover to the shortest path trees (SPTs) is available on theS6000 platform. After a receiver receives traffic from the RP, PM-SM switches to SPT to forward multicast traffic. Every multicast group has an RP and a unidirectional shared tree (group-specific shared tree).
Figure 88. Preventing a Source from Transmitting to a Group The following table lists the location and description shown in the previous illustration. Table 54. Preventing a Source from Transmitting to a Group — Description Location Description 1/21 • • • • Interface TenGigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • • Interface TenGigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Location Description • • ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface TenGigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 • • • • Interface TenGigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.
ip pim join-filter NOTE: When you configure a join filter that filter is applicable for both ingress and egress flows. There is no option to specify in or out parameters while configuring a join filter.
31 Object Tracking IPv4/IPv6 object tracking is available on Dell Networking OS. Object tracking allows the Dell Networking Operating System (OS) client processes, such as virtual router redundancy protocol (VRRP), to monitor tracked objects (for example, interface or link status) and take appropriate action when the state of an object changes. NOTE: In Dell Networking OS release version 8.4.1.0, object tracking is supported only on VRRP.
Figure 89. Object Tracking Example When you configure a tracked object, such as an IPv4/IPv6 a route or interface, you specify an object number to identify the object. Optionally, you can also specify: • UP and DOWN thresholds used to report changes in a route metric. • A time delay before changes in a tracked object’s state are reported to a client. Track Layer 2 Interfaces You can create an object to track the line-protocol state of a Layer 2 interface.
A tracked route matches a route in the routing table only if the exact address and prefix length match an entry in the routing table. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact address and prefix length, the tracked route is considered to be DOWN.
If you do not configure a delay, a notification is sent immediately as soon as a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds. VRRP Object Tracking As a client, VRRP can track up to 20 objects (including route entries, and Layer 2 and Layer 3 interfaces) in addition to the 12 tracked interfaces supported for each VRRP group. You can assign a unique priority-cost value from 1 to 254 to each tracked VRRP object or group interface.
Valid delay times are from 0 to 180 seconds. The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status.
Valid object IDs are from 1 to 65535. 2. (Optional) Configure the time delay used before communicating a change in the status of a tracked interface. OBJECT TRACKING mode delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status.
• By the reachability of the route's next-hop router. The UP/DOWN state of the route is determined by the entry of the next-hop address in the ARP cache. A tracked route is considered to be reachable if there is an ARP cache entry for the route's next-hop address. If the next-hop address in the ARP cache ages out for a route tracked for its reachability, an attempt is made to regenerate the ARP cache entry to see if the nexthop address appears before considering the route DOWN.
The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status. EXEC Privilege mode show track object-id Example of the track ip route reachability Command Example of the track ipv6 route reachability Command Dell(conf)#track 104 ip route 10.0.0.
Enter an IPv4 address in dotted decimal format. Valid IPv4 prefix lengths are from /0 to /32. Enter an IPv6 address in X:X:X:X::X format. Valid IPv6 prefix lengths are from /0 to /128. (Optional) E-Series only: For an IPv4 route, you can enter a VRF name. 3. (Optional) Configure the time delay used before communicating a change in the UP and/or DOWN status of a tracked route. OBJECT TRACKING mode delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0. 4.
• • Display the configuration and status of currently tracked Layer 2 or Layer 3 interfaces, IPv4 or IPv6 routes, and a VRF instance. show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] Use the show running-config track command to display the tracking configuration of a specified object or all objects that are currently configured on the router.
Example of Viewing Object Tracking Configuration Dell#show running-config track track 1 ip route 23.0.0.0/8 reachability track 2 ipv6 route 2040::/64 metric threshold delay down 3 delay up 5 threshold metric up 200 track 3 ipv6 route 2050::/64 reachability track 4 interface TenGigabitEthernet 1/4 ip routing track 5 ip route 192.168.0.
32 Open Shortest Path First (OSPFv2 and OSPFv3) Open shortest path first (OSPFv2 for IPv4) and OSPF version 3 (OSPF for IPv6) are supported on Dell Networking OS. This chapter provides a general description of OSPFv2 (OSPF for IPv4) and OSPFv3 (OSPF for IPv6) as supported in the Dell Networking Operating System (OS). NOTE: The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) are the same between OSPFv2 and OSPFv3.
Figure 90. Autonomous System Areas Area Types The backbone of the network is Area 0. It is also called Area 0.0.0.0 and is the core of any AS. All other areas must connect to Area 0. Areas can be defined in such a way that the backbone is not contiguous. In this case, backbone connectivity must be restored through virtual links. Virtual links are configured between any backbone routers that share a link to a non-backbone area and function as if they were direct links.
Networks and Neighbors As a link-state protocol, OSPF sends routing information to other OSPF routers concerning the state of the links between them. The state (up or down) of those links is important. Routers that share a link become neighbors on that segment. OSPF uses the Hello protocol as a neighbor discovery and keep alive mechanism. After two routers are neighbors, they may proceed to exchange and synchronize their databases, which creates an adjacency.
Figure 91. OSPF Routing Examples Backbone Router (BR) A backbone router (BR) is part of the OSPF Backbone, Area 0. This includes all ABRs. It can also include any routers that connect only to the backbone and another ABR, but are only part of Area 0, such as Router I in the previous example. Area Border Router (ABR) Within an AS, an area border router (ABR) connects one or more areas to the backbone.
Autonomous System Border Router (ASBR) The autonomous system border area router (ASBR) connects to more than one AS and exchanges information with the routers in other ASs. Generally, the ASBR connects to a non-interior gate protocol (IGP) such as BGP or uses static routes. Internal Router (IR) The internal router (IR) has adjacencies with ONLY routers in the same area, as Router E, M, and I shown in the previous example.
For all LSA types, there are 20-byte LSA headers. One of the fields of the LSA header is the link-state ID. Each router link is defined as one of four types: type 1, 2, 3, or 4. The LSA includes a link ID field that identifies, by the network number and mask, the object this link connects to. Depending on the type, the link ID has different meanings. • 1: point-to-point connection to another router/neighboring router. • 2: connection to a transit network IP address of the DR.
Figure 92. Priority and Cost Examples OSPF with Dell Networking OS Dell Networking OS supports up to 10,000 OSPF routes for OSPFv2. Within that 10,000 routes, you can designate up to 8,000 routes as external and up to 2,000 as inter/intra area routes. Dell Networking OS version 9.4(0.0) and later support only one OSPFv2 process per VRF. Dell Networking OS version 9.7(0.0) and later support OSPFv3 in VRF. Also, on OSPFv3, Dell Networking OS supports only one OSPFv3 process per VRF.
Graceful Restart When a router goes down without a graceful restart, there is a possibility for loss of access to parts of the network due to ongoing network topology changes. Additionally, LSA flooding and reconvergence can cause substantial delays. It is, therefore, desirable that the network maintains a stable topology if it is possible for data flow to continue uninterrupted.
Fast Convergence (OSPFv2, IPv4 Only) Fast convergence allows you to define the speeds at which LSAs are originated and accepted, and reduce OSPFv2 end-to-end convergence time. Dell Networking OS allows you to accept and originate LSAa as soon as they are available to speed up route information propagation. NOTE: The faster the convergence, the more frequent the route calculations and updates. This impacts CPU utilization and may impact adjacency stability in larger topologies.
LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c 00:10:41 : OSPF(1000:00): Rcv. v:2 t:5(LSAck) l:64 Acks 2 rid:2.2.2.2 aid:1500 chk:0xdbee aut:0 auk: keyid:0 from:Vl 100 LSType:Type-5 AS External id:160.1.1.0 adv:6.1.0.0 seq:0x8000000c LSType:Type-5 AS External id:160.1.2.0 adv:6.1.0.0 seq:0x8000000c 00:10:41 : OSPF(1000:00): Rcv. v:2 t:4(LSUpd) l:100 rid:6.1.0.0 aid:0 chk:0xccbd aut:0 auk: keyid:0 from:Gi 10/21 Number of LSA:2 LSType:Type-5 AS External(5) Age:1 Seq:0x8000000c id:170.1.1.
Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 1.1.1.2, Interface address 30.0.0.1 Backup Designated Router (ID) 1.1.1.1, Interface address 30.0.0.2 Timer intervals configured, Hello 20, Dead 80, Wait 20, Retransmit 5 Hello due in 00:00:04 Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 1.1.1.
timers spf 2 5 Dell(conf-router_ospf-1)# Dell(conf-router_ospf-1)#end Dell# For a complete list of the OSPF commands, refer to the OSPF section in the Dell Networking OS Command Line Reference Guide document. Enabling OSPFv2 To enable Layer 3 routing, assign an IP address to an interface (physical or Loopback). By default, OSPF, similar to all routing protocols, is disabled. You must configure at least one interface for Layer 3 before enabling OSPFv2 globally.
no router ospf process-id • Reset the OSPFv2 process. EXEC Privilege mode clear ip ospf process-id • View the current OSPFv2 status. EXEC mode show ip ospf process-id Example of Viewing the Current OSPFv2 Status Dell#show ip ospf 55555 Routing Process ospf 55555 with ID 10.10.10.
Example of Enabling OSPFv2 and Assigning an Area to an Interface Dell#(conf)#int te 4/14 Dell(conf-if-te-4/14)#ip address 10.10.10.10/24 Dell(conf-if-te-4/14)#no shutdown Dell(conf-if-te-4/14)#ex Dell(conf)#router ospf 1 Dell(conf-router_ospf-1)#network 1.2.3.4/24 area 0 Dell(conf-router_ospf-1)#network 10.10.10.10/24 area 1 Dell(conf-router_ospf-1)#network 20.20.20.
Process ID 1, Router ID 10.168.253.2, Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host. Dell# Configuring Stub Areas OSPF supports different types of LSAs to help reduce the amount of router processing within the areas. Type 5 LSAs are not flooded into stub areas; the ABR advertises a default route into the stub area to which it is attached. Stub area routers use the default route to reach external destinations.
• Specify whether all or some of the interfaces are passive. CONFIG-ROUTEROSPF- id mode passive-interface {default | interface} The default is enabled passive interfaces on ALL interfaces in the OSPF process. Entering the physical interface type, slot, and number enables passive interface on only the identified interface. – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
CONFIG-ROUTEROSPF- id mode fast-convergence {number} The parameter range is from 1 to 4. The higher the number, the faster the convergence. When disabled, the parameter is set at 0. NOTE: A higher convergence level can result in occasional loss of OSPF adjacency. Generally, convergence level 1 meets most convergence requirements. Only select higher convergence levels following consultation with Dell Technical Support.
– seconds: the range is from 1 to 65535 (the default is 40 seconds). The dead interval must be four times the hello interval. • The dead interval must be the same on all routers in the OSPF network. Change the time interval between hello-packet transmission. CONFIG-INTERFACE mode ip ospf hello-interval seconds – seconds: the range is from 1 to 65535 (the default is 10 seconds). • The hello interval must be the same on all routers in the OSPF network.
interface TenGigabitEthernet 1/1 ip address 10.1.2.100 255.255.255.0 no shutdown ip ospf cost 45 Dell(conf-if)#end Dell#show ip ospf 34 interface TenGigabitEthernet 1/1 is up, line protocol is up Internet Address 10.1.2.100/24, Area 2.2.2.2 Process ID 34, Router ID 10.1.2.100, Network Type BROADCAST, Cost: 45 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 10.1.2.100, Interface address 10.1.2.100 Backup Designated Router (ID) 10.1.2.100, Interface address 0.0.0.
CONFIG-ROUTEROSPF- id mode graceful-restart grace-period seconds The seconds range is from 40 and 3000. This setting is the time that an OSPFv2 router’s neighbors advertises it as fully adjacent, regardless of the synchronization state, during a graceful restart. OSPFv2 terminates this process when the grace period ends. 2. Enter the Router ID of the OSPFv2 helper router from which the router does not accept graceful restart assistance.
Creating Filter Routes To filter routes, use prefix lists. OSPF applies prefix lists to incoming or outgoing routes. Incoming routes must meet the conditions of the prefix lists. If they do not, OSPF does not add the route to the routing table. Configure the prefix list in CONFIGURATION PREFIX LIST mode prior to assigning it to the OSPF process. • Create a prefix list and assign it a unique name. CONFIGURATION mode ip prefix-list prefix-name • You are in PREFIX LIST mode.
– tag tag-value: the range is from 0 to 4294967295. Example of Viewing OSPF Configuration after Redistributing Routes To view the current OSPF configuration, use the show running-config ospf command in EXEC mode or the show config command in ROUTER OSPF mode. Dell(conf-router_ospf)#show config ! router ospf 34 network 10.1.2.32 0.0.0.255 area 2.2.2.2 network 10.1.3.24 0.0.0.255 area 3.3.3.
show ip ospf timers rate-limit • View debug messages. EXEC Privilege mode debug ip ospf process-id [event | packet | spf | database-timers rate-limit] To view debug messages for a specific OSPF process ID, use the debug ip ospf process-id command. If you do not enter a process ID, the command applies to the first OSPF process. To view debug messages for a specific operation, enter one of the optional keywords: – event: view OSPF event messages. – packet: view OSPF packet information.
Figure 93. Basic Topology and CLI Commands for OSPFv2 OSPF Area 0 — Te 1/1 and 1/2 router ospf 11111 network 10.0.11.0/24 area 0 network 10.0.12.0/24 area 0 network 192.168.100.0/24 area 0 ! interface TenGigabitEthernet 1/1 ip address 10.1.11.1/24 no shutdown ! interface TenGigabitEthernet 1/2 ip address 10.2.12.2/24 no shutdown ! interface Loopback 10 ip address 192.168.100.100/24 no shutdown OSPF Area 0 — Te 3/1 and 3/2 router ospf 33333 network 192.168.100.0/24 area 0 network 10.0.13.
ip address 192.168.100.20/24 no shutdown ! interface TenGigabitEthernet 2/1 ip address 10.2.21.2/24 no shutdown ! interface TenGigabitEthernet 2/2 ip address 10.2.22.2/24 no shutdown Configuration Task List for OSPFv3 (OSPF for IPv6) The configuration options of OSPFv3 are the same as those options for OSPFv2, but you may configure OSPFv3 with differently labeled commands. Specify process IDs and areas and include interfaces and addresses in the process. Define areas as stub or totally stubby.
Assigning IPv6 Addresses on an Interface To assign IPv6 addresses to an interface, use the following commands. 1. Assign an IPv6 address to the interface. CONF-INT-type slot/port mode ipv6 address ipv6 address IPv6 addresses are normally written as eight groups of four hexadecimal digits; separate each group by a colon (:). The format is A:B:C::F/128. 2. Bring up the interface.
CONFIGURATION mode no ipv6 router ospf process-id • Reset the OSPFv3 process. EXEC Privilege mode clear ipv6 ospf process Assigning OSPFv3 Process ID and Router ID to a VRF To assign, disable, or reset OSPFv3 on a non-default VRF, use the following commands. • Enable the OSPFv3 process on a non-default VRF and enter OSPFv3 mode. CONFIGURATION mode ipv6 router ospf {process ID} vrf {vrf-name} • The process ID range is from 0 to 65535. Assign the router ID for this OSPFv3 process.
passive-interface {interface slot/port} Interface: identifies the specific interface that is passive. – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. – For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. – For a port channel interface, enter the keywords port-channel then a number. – For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA. To enable OSPFv3 graceful restart, enter the ipv6 router ospf process-id command to enter OSPFv3 configuration mode. Then configure a grace period using the graceful-restart grace-period command. The grace period is the time that the OSPFv3 neighbors continue to advertise the restarting router as though it is fully adjacent.
show ipv6 ospf database [vrf vrf-name] database-summary Examples of the Graceful Restart show Commands The following example shows the show run ospf command. Dell#show run ospf ! router ospf 1 router-id 200.1.1.1 log-adjacency-changes graceful-restart grace-period 180 network 20.1.1.0/24 area 0 network 30.1.1.0/24 area 0 ! ipv6 router ospf 1 log-adjacency-changes graceful-restart grace-period 180 The following example shows the show ipv6 ospf database database-summary command.
OSPFv3 Authentication Using IPsec OSPFv3 uses IPsec to provide authentication for OSPFv3 packets. IPsec authentication ensures security in the transmission of OSPFv3 packets between IPsec-enabled routers. IPsec is a set of protocols developed by the internet engineering task force (IETF) to support secure exchange of packets at the IP layer. IPsec supports two encryption modes: transport and tunnel. • Transport mode — encrypts only the data portion (payload) of each packet, but leaves the header untouched.
• In an OSPFv3 authentication policy: – AH is used to authenticate OSPFv3 headers and certain fields in IPv6 headers and extension headers. – MD5 and SHA1 authentication types are supported; encrypted and unencrypted keys are supported. • In an OSPFv3 encryption policy: – Both encryption and authentication are used. – IPsec security associations (SAs) are supported only in Transport mode (Tunnel mode is not supported).
• Display the security associations set up for OSPFv3 interfaces in authentication policies. show crypto ipsec sa ipv6 Configuring IPsec Encryption on an Interface To configure, remove, or display IPsec encryption on an interface, use the following commands.
The configuration of IPSec authentication on an interface-level takes precedence over an area-level configuration. If you remove an interface configuration, an area authentication policy that has been configured is applied to the interface. • Enable IPSec authentication for OSPFv3 packets in an area. CONF-IPV6-ROUTER-OSPF mode area-id authentication ipsec spi number {MD5 | SHA1} [key-encryption-type] key – area area-id: specifies the area for which OSPFv3 traffic is to be authenticated.
– authentication-algorithm: specifies the authentication algorithm to use for encryption. The valid values are MD5 or SHA1. – key: specifies the text string used in authentication. All neighboring OSPFv3 routers must share key to exchange information. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted).
Inbound AH Key Outbound AH Key Transform set : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97e : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97e : ah-md5-hmac Crypto IPSec client security policy data Policy name : OSPFv3-0-501 Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97eb7c0c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9
Troubleshooting OSPFv3 Use the information in this section to troubleshoot OSPFv3 operation on the switch. NOTE: The following tasks are not a comprehensive; they provide some examples of typical troubleshooting checks.
33 Policy-based Routing (PBR) Policy-based Routing (PBR) allows a switch to make routing decisions based on policies applied to an interface. Overview When a router receives a packet, the router normally decides where to forward the packet based on the destination address in the packet, which is used to look up an entry in a routing table. However, in some cases, there may be a need to forward the packet based on other criteria: size, source, protocol type, destination, and so forth.
• Destination port • TCP Flags After a redirect-list is applied to an interface, all traffic passing through it is subjected to the rules defined in the redirect-list. The traffic is forwarded based on the following: • Next-hop addresses are verified. If the specified next hop is reachable, the traffic is forwarded to the specified next-hop. • If the specified next-hops are not reachable, the normal routing table is used to forward the traffic.
• Create a Track-id list. For complete tracking information, refer to Object Tracking chapter. • Apply a Redirect-list to an Interface using a Redirect-group PBR Exceptions (Permit) To create an exception to a redirect list, use the permit command. Use exceptions when a forwarding decision is based on the routing table rather than a routing policy.
• ip-address is the Forwarding router’s address • tunnel is used to configure the tunnel settings • tunnel-id is used to redirect the traffic • track is used to track the object-id • track is to enable the tracking • FORMAT: A.B.C.D • FORMAT: slot/port • ip-protocol-number or protocol-type is the type of protocol to be redirected • FORMAT: 0-255 for IP protocol number, or enter protocol type • source ip-address or any or host ip-address is the Source’s IP address • FORMAT: A.B.
Example: Creating Multiple Rules for a Redirect-List Dell(conf)#ip redirect-list test Dell(conf-redirect-list)#seq 10 redirect Dell(conf-redirect-list)#seq 15 redirect Dell(conf-redirect-list)#seq 20 redirect Dell(conf-redirect-list)#show config ! ip redirect-list test seq 10 redirect 10.1.1.2 ip 20.1.1.0/24 seq 15 redirect 10.1.1.3 ip 20.1.1.0/25 seq 20 redirect 10.1.1.3 ip 20.1.1.0/24 Dell(conf-redirect-list)# 10.1.1.2 ip 20.1.1.0/24 any 10.1.1.3 ip 20.1.1.0/25 any 10.1.1.3 ip 20.1.1.
shutdown Dell(conf-if-te-1/2)# Dell(conf-if-gi-1/1)#ip redirect-group test Dell(conf-if-gi-1/1)#ip redirect-group xyz Dell(conf-if-gi-1/1)#show config ! interface GigabitEthernet 1/1 no ip address ip redirect-group test ip redirect-group xyz shutdown Dell(conf-if-te-1/2)# In addition to supporting multiple redirect-lists in a redirect-group, multiple redirect-groups are supported on a single interface. Dell Networking OS has the capability to support multiple groups on an interface for backup purposes.
Use the show ip redirect-list (without the list name) to display all the redirect-lists configured on the device. Dell#show ip redirect-list IP redirect-list rcl0: Defined as: seq 5 permit ip 200.200.200.200 200.200.200.200 199.199.199.199 199.199.199.199 seq 10 redirect 1.1.1.2 tcp 234.224.234.234 255.234.234.234 222.222.222.
Create the Redirect-List GOLD EDGE_ROUTER(conf-if-Te-2/23)#ip redirect-list GOLD EDGE_ROUTER(conf-redirect-list)#description Route GOLD traffic to ISP_GOLD. EDGE_ROUTER(conf-redirect-list)#direct 10.99.99.254 ip 192.168.1.0/24 any EDGE_ROUTER(conf-redirect-list)#redirect 10.99.99.254 ip 192.168.2.0/24 any EDGE_ROUTER(conf-redirect-list)# seq 15 permit ip any any EDGE_ROUTER(conf-redirect-list)#show config ! ip redirect-list GOLD description Route GOLD traffic to ISP_GOLD. seq 5 redirect 10.99.99.254 ip 192.
IP redirect-list GOLD: Defined as: seq 5 redirect 10.99.99.254 ip 192.168.1.0/24 any, Next-hop reachable (via Te 3/23) seq 10 redirect 10.99.99.254 ip 192.168.2.0/24 any, Next-hop reachable (via Te 3/23) seq 15 permit ip any any Applied interfaces: Te 2/11 EDGE_ROUTER# Configuration Tasks for Creating a PBR list using Explicit Track Objects for Redirect IP's Create Track Objects to track the Redirect IP's: Dell#configure terminal Dell(conf)#track 3 ip host 42.1.1.
Configuration Tasks for Creating a PBR list using Explicit Track Objects for Tunnel Interfaces Creating steps for Tunnel Interfaces: Dell#configure terminal Dell(conf)#interface tunnel 1 Dell(conf-if-tu-1)#tunnel destination 40.1.1.2 Dell(conf-if-tu-1)#tunnel source 40.1.1.1 Dell(conf-if-tu-1)#tunnel mode ipip Dell(conf-if-tu-1)#tunnel keepalive 60.1.1.2 Dell(conf-if-tu-1)#ip address 60.1.1.
IP redirect-list explicit_tunnel: Defined as: seq 5 redirect tunnel 1 track 1 tcp 155.55.2.0/24 222.22.2.0/24, Track 1 [up], Next-hop reachable (via Te 1/32) seq 10 redirect tunnel 1 track 1 tcp any any, Track 1 [up], Next-hop reachable (via Te 1/32) seq 15 redirect tunnel 1 track 1 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Next-hop reachable (via Te 1/32) seq 20 redirect tunnel 2 track 2 tcp 155.55.2.0/24 222.22.2.
34 PIM Sparse-Mode (PIM-SM) Protocol-independent multicast sparse-mode (PIM-SM) is supported on Dell Networking OS. PIM-SM is a multicast protocol that forwards multicast traffic to a subnet only after a request using a PIM Join message; this behavior is the opposite of PIM-Dense mode, which forwards multicast traffic to all subnets until a request to stop. Implementation Information The following information is necessary for implementing PIM-SM.
Refuse Multicast Traffic A host requesting to leave a multicast group sends an IGMP Leave message to the last-hop DR. If the host is the only remaining receiver for that group on the subnet, the last-hop DR is responsible for sending a PIM Prune message up the RPT to prune its branch to the RP. 1. After receiving an IGMP Leave message, the gateway removes the interface on which it is received from the outgoing interface list of the (*,G) entry.
ip multicast-routing Related Configuration Tasks The following are related PIM-SM configuration tasks. • • • • Configuring S,G Expiry Timers Configuring a Static Rendezvous Point Configuring a Designated Router Creating Multicast Boundaries and Domains Enable PIM-SM You must enable PIM-SM on each participating interface. 1. Enable multicast routing on the system. CONFIGURATION mode ip multicast-routing 2. Enable PIM-Sparse mode.
(10.87.31.5, 192.1.2.1), uptime 00:01:24, expires 00:02:26, flags: FT Incoming interface: TenGigabitEthernet 2/11, RPF neighbor 0.0.0.0 Outgoing interface list: TenGigabitEthernet 1/11 TenGigabitEthernet 1/12 TenGigabitEthernet 2/13 --More-- Configuring S,G Expiry Timers By default, S, G entries expire in 210 seconds. You can configure a global expiry time (for all [S,G] entries) or configure an expiry time for a particular entry.
Configuring a Static Rendezvous Point The rendezvous point (RP) is a PIM-enabled interface on a router that acts as the root a group-specific tree; every group must have an RP. • Identify an RP by the IP address of a PIM-enabled or Loopback interface. ip pim rp-address Example of Viewing an RP on a Loopback Interface Dell#sh run int loop0 ! interface Loopback 0 ip address 1.1.1.1/32 ip pim sparse-mode no shutdown Dell#sh run pim ! ip pim rp-address 1.1.1.1 group-address 224.0.0.
• Change the interval at which a router sends hello messages. INTERFACE mode ip pim query-interval seconds • Display the current value of these parameter. EXEC Privilege mode show ip pim interface Creating Multicast Boundaries and Domains A PIM domain is a contiguous set of routers that all implement PIM and are configured to operate within a common boundary defined by PIM multicast border routers (PMBRs). PMBRs connect each PIM domain to the rest of the Internet.
35 PIM Source-Specific Mode (PIM-SSM) PIM source-specific mode (PIM-SSM) is supported on Dell Networking OS. PIM-SSM is a multicast protocol that forwards multicast traffic from a single source to a subnet. In the other versions of protocol independent multicast (PIM), a receiver subscribes to a group only. The receiver receives traffic not just from the source in which it is interested but from all sources sending to that group.
Enabling PIM-SSM To enable PIM-SSM, follow these steps. 1. Create an ACL that uses permit rules to specify what range of addresses should use SSM. CONFIGURATION mode ip access-list standard name 2. Enter the ip pim ssm-range command and specify the ACL you created. CONFIGURATION mode ip pim ssm-range acl-name Enabling PIM-SSM To display address ranges in the PIM-SSM range, use the show ip pim ssm-range command from EXEC Privilege mode. R1(conf)#do show run pim ! ip pim rp-address 10.11.12.
ip pim rp-address 10.11.12.2 group-address 224.0.0.0/4 ip pim ssm-range ssm R1(conf)#do show run acl ! ip access-list standard map seq 5 permit host 239.0.0.2 ! ip access-list standard ssm seq 5 permit host 239.0.0.2 R1(conf)#ip igmp ssm-map map 10.11.5.2 R1(conf)#do show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface Mode Uptime Expires 239.0.0.2 Vlan 300 IGMPv2-Compat 00:00:07 Never Member Ports: Te 1/1 239.0.0.1 Vlan 400 INCLUDE 00:00:10 Never 10.11.4.
Member Ports: Te 1/1/1 R1(conf)#do show ip igmp ssm-map 239.0.0.2 SSM Map Information Group : 239.0.0.2 Source(s) : 10.11.5.2 R1(conf)#do show ip igmp groups detail Interface Group Uptime Expires Router mode Last reporter Last reporter mode Last report Group source Source address 10.11.5.2 00:00:01 Vlan 300 239.0.0.2 00:00:01 Never IGMPv2-Compat 10.11.3.2 IGMPv2 received Join list Uptime Expires Never Interface Vlan 400 Group 239.0.0.1 Uptime 00:00:05 Expires Never Router mode INCLUDE Last reporter 10.11.
36 Port Monitoring Port monitoring is supported on Dell Networking OS. Mirroring is used for monitoring Ingress or Egress or both Ingress and Egress traffic on a specific port(s). This mirrored traffic can be sent to a port where a network sniffer can connect and monitor the traffic.
point to another new destination (for example, 1/4). If you attempt to configure another destination (to create 5 MG port), this message displays: % Error will be thrown in case of RPM and ERPM features.
Figure 94. Port Monitoring Configurations on the S-Series Dell Networking OS Behavior: All monitored frames are tagged if the configured monitoring direction is egress (TX), regardless of whether the monitored port (MD) is a Layer 2 or Layer 3 port. If the MD port is a Layer 2 port, the frames are tagged with the VLAN ID of the VLAN to which the MD belongs. If the MD port is a Layer 3 port, the frames are tagged with VLAN ID 4095.
0 Te 1/1 Te 1/2 rx Port N/A N/A Dell(conf)#monitor session 0 Dell(conf-mon-sess-0)#source po 10 dest ten 1/2 dir rx Dell(conf-mon-sess-0)#do show monitor session SessID Source Destination Dir Mode Source IP ------ ------------------ ---- --------0 Te 1/1 Te 1/2 rx Port N/A 0 Po 10 Te 1/2 rx Port N/A Dest IP -------N/A N/A Dell(conf)#monitor session 1 Dell(conf-mon-sess-1)#source vl 40 dest ten 1/3 dir rx Dell(conf-mon-sess-1)#flow-based enable Dell(conf-mon-sess-1)#exit Dell(conf)#do show monitor s
monitor multicast-queue queue-id Dell(conf)#monitor multicast-queue 7 2. Verify information about monitor configurations. EXEC mode EXEC Privilege mode show run monitor session Dell#show run monitor session ! monitor multicast-queue 7 Dell# Enabling Flow-Based Monitoring Flow-based monitoring is supported only on the S-Series platform. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead of all traffic on the interface.
! Extended Ingress IP access list testflow on TenGigabitEthernet 1/1 Total cam count 4 seq 5 permit icmp any any monitor count bytes (0 packets 0 bytes) seq 10 permit ip 102.1.1.
Configuring Remote Port Mirroring Remote port mirroring requires a source session (monitored ports on different source switches), a reserved tagged VLAN for transporting mirrored traffic (configured on source, intermediate, and destination switches), and a destination session (destination ports connected to analyzers on destination switches).
• MAC address learning in the reserved VLAN is automatically disabled. • The reserved VLAN for remote port mirroring can be automatically configured in intermediate switches by using GVRP. • There is no restriction on the VLAN IDs used for the reserved remote-mirroring VLAN. Valid VLAN IDs are from 2 to 4094. The default VLAN ID is not supported.
To display the currently configured source and destination sessions for remote port mirroring on a switch, enter the show monitor session command in EXEC Privilege mode.
Dell(conf-mon-sess-1)#no disable Dell(conf-mon-sess-1)#exit Dell(conf)#inte vlan 100 Dell(conf-if-vl-100)#tagged te 1/7 Dell(conf-if-vl-100)#exit Dell(conf)#interface vlan 20 Dell(conf-if-vl-20)#mode remote-port-mirroring Dell(conf-if-vl-20)#tagged te 1/6 Dell(conf-if-vl-20)#exit Dell(conf)#monitor session 2 type rpm Dell(conf-mon-sess-2)#source vlan 100 destination remote-vlan 20 dir rx Dell(conf-mon-sess-2)#no disable Dell(conf-mon-sess-2)#flow-based enable Dell(conf-mon-sess-2)#exit Dell(conf)#mac access
Dell(conf)#interface te 1/3 Dell(conf-if-te-1/3)#switchport Dell(conf-if-te-1/3)#no shutdown Dell(conf-if-te-1/3)#exit Dell(conf)#inte vlan 10 Dell(conf-if-vl-10)#mode remote-port-mirroring Dell(conf-if-vl-10)#tagged te 1/1 Dell(conf-if-vl-10)#exit Dell(conf)#inte vlan 20 Dell(conf-if-vl-20)#mode remote-port-mirroring Dell(conf-if-vl-20)#tagged te 1/2 Dell(conf-if-vl-20)#exit Dell(conf)#interface vlan 30 Dell(conf-if-vl-30)#mode remote-port-mirroring Dell(conf-if-vl-30)#tagged te 1/3 Dell(conf-if-vl-30)#exi
5. Show the output for the LACP. Dell#show interfaces port-channel brief Codes: L - LACP Port-channel O - OpenFlow Controller Port-channel LAG L1 L2 Dell# Mode L3 L2 Status up up Uptime 00:01:17 00:00:58 Ports Te 1/4 Te 1/5 (Up) (Up) Configuring the Encapsulated Remote Port Mirroring The ERPM session copies traffic from the source ports/lags or source VLANs and forwards the traffic using routable GREencapsulated packets to the destination ip address specified in the session.
4 direction Specify rx, tx or both in case to monitor ingress/ egress or both ingress and egress packets on the specified port.. 5 erpm source-ip dest-ip Specify the source ip address and the destination ip where the packet needs to be sent. 6 flow-based enable Specify flow-based enable for mirroring on a flow by flow basis and also for vlan as source. 7 no disable No disable command is mandatory in order for a erpm session to be active.
ERPM Behavior on a typical Dell Networking OS The Dell Networking OS is designed to support only the Encapsulation of the data received / transmitted at the specified source port (Port A). An ERPM destination session / decapsulation of the ERPM packets at the destination Switch are not supported. As seen in the above figure, the packets received/transmitted on Port A will be encapsulated with an IP/GRE header plus a new L2 header and sent to the destination ip address (Port D’s ip address) on the sniffer.
b. Using Python script – Either have a Linux server's ethernet port ip as the ERPM destination ip or connect the ingress interface of the server to the ERPM MirrorToPort. The analyzer should listen in the forward/egress interface. If there is only one interface, one can choose the ingress and forward interface to be same and listen in the tx direction of the interface. – Download/ Write a small script (for example: erpm.
37 Per-VLAN Spanning Tree Plus (PVST+) Per-VLAN spanning tree plus (PVST+) is supported on Dell Networking OS. Protocol Overview PVST+ is a variation of spanning tree — developed by a third party — that allows you to configure a separate spanning tree instance for each virtual local area network (VLAN). For more information about spanning tree, refer to the Spanning Tree Protocol (STP) chapter. Figure 96.
Dell Networking Term IEEE Specification Multiple Spanning Tree Protocol (MSTP) 802 .1s Per-VLAN Spanning Tree Plus (PVST+) Third Party Implementation Information • The Dell Networking OS implementation of PVST+ is based on IEEE Standard 802.1w. • The Dell Networking OS implementation of PVST+ uses IEEE 802.1s costs as the default costs (as shown in the following table). Other implementations use IEEE 802.1w costs as the default costs.
PROTOCOL PVST mode disable • Disable PVST+ on an interface, or remove a PVST+ parameter configuration. INTERFACE mode no spanning-tree pvst Example of Viewing PVST+ Configuration To display your PVST+ configuration, use the show config command from PROTOCOL PVST mode.
The bridge with the bridge value for bridge priority is elected root. Because all bridges use the default priority (until configured otherwise), the lowest MAC address is used as a tie-breaker. To increase the likelihood that a bridge is selected as the STP root, assign bridges a low non-default value for bridge priority. To assign a bridge priority, use the following command. • Assign a bridge priority. PROTOCOL PVST mode vlan bridge-priority The range is from 0 to 61440. The default is 32768.
• The default is 15 seconds. Change the hello-time parameter. PROTOCOL PVST mode vlan hello-time NOTE: With large configurations (especially those configurations with more ports), Dell Networking recommends increasing the hello-time. The range is from 1 to 10. • The default is 2 seconds. Change the max-age parameter. PROTOCOL PVST mode vlan max-age The range is from 6 to 40. The default is 20 seconds. The values for global PVST+ parameters are given in the output of the show spanning-tree pvst command.
• Refer to the table for the default values. Change the port priority of an interface. INTERFACE mode spanning-tree pvst vlan priority. The range is from 0 to 240, in increments of 16. The default is 128. The values for interface PVST+ parameters are given in the output of the show spanning-tree pvst command, as previously shown. Configuring an EdgePort The EdgePort feature enables interfaces to begin forwarding traffic approximately 30 seconds sooner.
Networking OS from executing this action, use the no spanning-tree pvst err-disable cause invalid-pvstbpdu command. After you configure this command, if the port receives a PVST+ BPDU, the BPDU is dropped and the port remains operational. Enabling PVST+ Extend System ID In the following example, ports P1 and P2 are untagged members of different VLANs. These ports are untagged because the hub is VLAN unaware.
switchport no shutdown ! interface TenGigabitEthernet 1/32 no ip address switchport no shutdown ! protocol spanning-tree pvst no disable vlan 100 bridge-priority 4096 interface Vlan 100 no ip address tagged TenGigabitEthernet 1/22,32 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 1/22,32 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/22,32 no shutdown ! protocol spanning-tree pvst no disable vlan 100 bridge-priority 4096 Example of PVST+ Configuration (
no shutdown ! interface Vlan 100 no ip address tagged TenGigabitEthernet 3/12,22 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 3/12,22 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 3/12,22 no shutdown ! protocol spanning-tree pvst no disable vlan 300 bridge-priority 4096 Per-VLAN Spanning Tree Plus (PVST+) 633
38 Quality of Service (QoS) Quality of service (QoS) is supported on Dell Networking OS. Differentiated service is accomplished by classifying and queuing traffic, and assigning priorities to those queues. Table 57.
Feature Direction Create Input Policy Maps Ingress Honor DSCP Values on Ingress Packets Ingress Honoring dot1p Values on Ingress Packets Ingress Create Output Policy Maps Egress Specify an Aggregate QoS Policy Egress Create Output Policy Maps Egress Enabling QoS Rate Adjustment Enabling Strict-Priority Queueing Egress Weighted Random Early Detection Create WRED Profiles Egress Figure 99.
• • • • RFC 2474, Definition of the Differentiated Services Field (DS Field) in the IPv4 Headers RFC 2475, An Architecture for Differentiated Services RFC 2597, Assured Forwarding PHB Group RFC 2598, An Expedited Forwarding PHB You cannot configure port-based and policy-based QoS on the same interface. Port-Based QoS Configurations You can configure the following QoS features on an interface.
NOTE: You cannot configure service-policy input and service-class dynamic dot1p on the same interface. • Honor dot1p priorities on ingress traffic. INTERFACE mode service-class dynamic dot1p Example of Configuring an Interface to Honor dot1p Priorities on Ingress Traffic Dell#configure terminal Dell(conf)#interface tengigabitethernet 1/1 Dell(conf-if-te-1/1)#service-class dynamic dot1p Dell(conf-if-te-1/1)#end Priority-Tagged Frames on the Default VLAN Priority-tagged frames are 802.
Example of rate shape Command Dell#configure terminal Dell(conf)#interface tengigabitethernet 1/1 Dell(conf-if-te-1/1)#rate shape 500 50 Dell(conf-if-te-1/1)#end Policy-Based QoS Configurations Policy-based QoS configurations consist of the components shown in the following example. Figure 100. Constructing Policy-Based QoS Configurations Classify Traffic Class maps differentiate traffic so that you can apply separate quality of service policies to different types of traffic.
NOTE: IPv6 and IP-any class maps cannot match on ACLs or VLANs. Use step 1 or step 2 to start creating a Layer 3 class map. 1. Create a match-any class map. CONFIGURATION mode class-map match-any 2. Create a match-all class map. CONFIGURATION mode class-map match-all 3. Specify your match criteria. CLASS MAP mode match {ip | ipv6 | ip-any} After you create a class-map, Dell Networking OS places you in CLASS MAP mode. Match-any class maps allow up to five ACLs. Match-all class-maps allow only one ACL.
Creating a Layer 2 Class Map All class maps are Layer 3 by default; however, you can create a Layer 2 class map by specifying the layer2 option with the class-map command. A Layer 2 class map differentiates traffic according to 802.1p value and/or VLAN and/or characteristics defined in a MAC ACL.. Use Step 1 or Step 2 to start creating a Layer 2 class map. 1. Create a match-any class map. CONFIGURATION mode class-map match-any 2. Create a match-all class map. CONFIGURATION mode class-map match-all 3.
EXEC Privilege mode show qos class-map Examples of Traffic Classifications The following example shows incorrect traffic classifications.
Dot1p to Queue Mapping Requirement The dot1p to queue mapping on the system is global and this is used to configure the PRIO2COS table configuration. For DSCP based PFC feature on untagged packets, this mapping must be the same as the default dot1p to queue mapping and should not be changed (as in TABLE 1). If a custom dot1p to queue mapping is present it should be reconfigured to the default dot1p to queue mapping.
Creating an Input QoS Policy To create an input QoS policy, use the following steps. 1. Create a Layer 3 input QoS policy. CONFIGURATION mode qos-policy-input Create a Layer 2 input QoS policy by specifying the keyword layer2 after the qos-policy-input command. 2.
Allocating Bandwidth to Queue Schedule packets for egress based on Deficit Round Robin (DRR). These strategies both offer a guaranteed data rate. The following table lists the default bandwidth weights for each queue, and their equivalent percentage which is derived by dividing the bandwidth weight by the sum of all queue weights. Table 59. Default Bandwidth Weights Queue Default Weight Equivalent Percentage 0 1 6.67% 1 2 13.33% 2 4 26.67% 3 8 53.33% • Allocate bandwidth to queues.
1. Create the color-aware map QoS DSCP color map. CONFIGURATION mode qos dscp-color-map color-map-name 2. Create the color aware map profile. DSCP-COLOR-MAP dscp {yellow | red} {list-dscp-values} 3. Apply the map profile to the interface. CONFIG-INTERFACE mode qos dscp-color-policy color-map-name Example: Create a DSCP Color Map The following example creates a DSCP color map profile, color-awareness policy, and applies it to interface te 1/11.
interface: Enter the name of the interface that has the color policy configured. Examples for Displaying a DSCP Color Policy Display summary information about a color policy for one or more interfaces. Dell# show qos dscp-color-policy summary Interface dscp-color-map TE 1/10 mapONE TE 1/11 mapTWO Display summary information about a color policy for a specific interface.
POLICY-MAP-IN mode policy-service-queue qos-polcy Honoring DSCP Values on Ingress Packets Dell Networking OS provides the ability to honor DSCP values on ingress packets using Trust DSCP feature. The following table lists the standard DSCP definitions and indicates to which queues Dell Networking OS maps DSCP values. When you configure trust DSCP, the matched packets and matched bytes counters are not incremented in the show qos statistics. Table 60.
Table 62. Default dot1p to Queue Mapping dot1p Queue ID 0 2 1 0 2 1 3 3 4 4 5 5 6 6 7 7 The dot1p value is also honored for frames on the default VLAN. For more information, refer to Priority-Tagged Frames on the Default VLAN. • Enable the trust dot1p feature. POLICY-MAP-IN mode trust dot1p Mapping dot1p Values to Service Queues All traffic is by default mapped to the same queue, Queue 0.
service-policy input Specify the keyword layer2 if the policy map you are applying a Layer 2 policy map. Creating Output Policy Maps 1. Create an output policy map. CONFIGURATION mode policy-map-output 2. After you create an output policy map, do one or more of the following: Applying an Output QoS Policy to a Queue Specifying an Aggregate QoS Policy Applying an Output Policy Map to an Interface 3. Apply the policy map to an interface.
• Payload: (variable) • Cyclic redundancy check (CRC): 4 bytes • Inter-frame gap (IFG): (variable) You can optionally include overhead fields in rate metering calculations by enabling QoS rate adjustment. QoS rate adjustment is disabled by default. • Specify the number of bytes of packet overhead to include in rate limiting, policing, and shaping calculations. CONFIGURATION mode qos-rate-adjust overhead-bytes For example, to include the Preamble and SFD, type qos-rate-adjust 8.
But when queue 1 gets congested on switch B, PFC frames for tagged packets will not be generated as PFC is not enabled on dot1p priority 5. Support for marking dot1p value in L3 Input Qos Policy In case the incoming packet is untagged and the packet which goes out to the peer is tagged, then the dot1p should be marked appropriately using L3 Input Qos Policy. This is required because in the peer switch PFC will be generated based on the dot1p value.
Figure 101. Packet Drop Rate for WRED You can create a custom WRED profile or use one of the five pre-defined profiles. Creating WRED Profiles To create WRED profiles, use the following commands. 1. Create a WRED profile. CONFIGURATION mode wred-profile 2. Specify the minimum and maximum threshold values. WRED mode threshold Applying a WRED Profile to Traffic After you create a WRED profile, you must specify to which traffic Dell Networking OS should apply the profile.
Displaying Default and Configured WRED Profiles To display the default and configured WRED profiles, use the following command. • Display default and configured WRED profiles and their threshold values. EXEC mode show qos wred-profile Displaying WRED Drop Statistics To display WRED drop statistics, use the following command. • Display the number of packets Dell Networking OS the WRED profile drops.
17 Dell# MCAST 0 0 0 0 Pre-Calculating Available QoS CAM Space Before Dell Networking OS version 7.3.1, there was no way to measure the number of CAM entries a policy-map would consume (the number of CAM entries that a rule uses is not predictable; from 1 to 16 entries might be used per rule depending upon its complexity). Therefore, it was possible to apply to an interface a policy-map that requires more entries than are available.
Specifying Policy-Based Rate Shaping in Packets Per Second Configuration of rate shaping in packets per second (pps) for QoS output policies is supported on the S6000 platform. You can configure rate shaping in pps for a QoS output policy, apart from specifying the rate shaping value in bytes. You can also configure the peak rate and the committed rate for packets in kilobits per second (Kbps) or pps.
QOS-POLICY-OUT mode Dell(config-qos-policy-out)# rate shape Kbps peak-rate burst-KB committed Kbps committed-rate burst-KB Configuring Weights and ECN for WRED The feature to configure a weight factor for weighted random early detection (WRED) and Explicit Congestion Notification (ECN) functionality for backplane ports is supported on the Additionally, the feature to configure a weight for WRED and ECN functionality for front-end ports is supported on the S6000 platform.
You can define WRED profiles and weight on each of the global service-pools for both loss-based and lossless (PFC) service- pools. The following events occur when you configure WRED and ECN on global service-pools: • If WRED/ECN is enabled on the global service-pool with threshold values and if it is not enabled on the queues, WRED/ECN are not effective based on global service-pool WRED thresholds.
when the threshold value is exceeded. If you configure ECN for WRED, devices employ this functionality of ECN to mark the packets and reduce the rate of sending packets in a congested, heavily-loaded network. To configure the weight factor for WRED and ECN capabilities, global buffer pools for multiple queues, and associating a service class with ECN marking, perform the following: 1. Configure the weight factor for the computation of average-queue size. This weight value applies to front-end ports.
• If single rate two color policer is configured along with this feature, then by default all packets less than PIR would be considered as “Green” But ‘Green’ packets matching the specific match criteria for which ‘color-marking’ is configured will be over-written and marked as “Yellow”.
As a part of this feature, the 2-bit ECN field of the IPv4 packet will also be available to be configured as one of the match qualifier. This way the entire 8-bit ToS field of the IPv4 header shall be used to classify traffic. The Dell Networking OS Release 9.3(0.0) supports the following QOS actions in the ingress policy based QOS: 1. Rate Policing 2. Queuing 3. Marking For the L3 Routed packets, the DSCP marking is the only marking action supported in the software.
• set the packet color as ‘yellow’ • set the packet color as ‘yellow’ and set a new DSCP for the packet This marking action to set the color of the packet is allowed only on the ‘match-any’ logical operator of the class-map.
! ip access-list standard dscp_40_non_ecn seq 5 permit any dscp 40 ecn 0 ! class-map match-any class_dscp_40 match ip access-group dscp_40_non_ecn set-color yellow match ip access-group dscp_40_ecn ! class-map match-any class_dscp_50 match ip access-group dscp_50_non_ecn set-color yellow match ip access-group dscp_50_ecn ! policy-map-input pmap_dscp_40_50 service-queue 2 class-map class_dscp_40 service-queue 3 class-map class_dscp_50 Applying Layer 2 Match Criteria on a Layer 3 Interface To process Layer 3
the counters, at a particular time, using a triggering utility. The trigger can either be software-based or based on a predetermined threshold event. Software-based triggers are supported, which are the values derived from the show command output in the Max Use count mode. In Dell Networking OS Release 9.3(0.0), only the Max Use count mode of operation is supported for the computation of maximum counter values.
--------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 5 (interface Fo 1/148) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 9 (interface Fo 1/152) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 13 (interface Fo 1/156) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS -------------------------
UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Quality of Service (QoS) 665
39 Routing Information Protocol (RIP) Routing information protocol (RIP) is supported on Dell Networking OS. RIP is based on a distance-vector algorithm; it tracks distances or hop counts to nearby routers when establishing network connections. RIP protocol standards are listed in the Standards Compliance chapter. Protocol Overview RIP is the oldest interior gateway protocol. There are two versions of RIP: RIP version 1 (RIPv1) and RIP version 2 (RIPv2). These versions are documented in RFCs 1058 and 2453.
Table 64. RIP Defaults Feature Default Interfaces running RIP • • Listen to RIPv1 and RIPv2 Transmit RIPv1 RIP timers • • • • update timer = 30 seconds invalid timer = 180 seconds holddown timer = 180 seconds flush timer = 240 seconds Auto summarization Enabled ECMP paths supported 16 Configuration Information By default, RIP is disabled in Dell Networking OS. To configure RIP, you must use commands in two modes: ROUTER RIP and INTERFACE.
Examples of Verifying RIP is Enabled and Viewing RIP Routes After designating networks with which the system is to exchange RIP information, ensure that all devices on that network are configured to exchange RIP information. The Dell Networking OS default is to send RIPv1 and to receive RIPv1 and RIPv2. To change the RIP version globally, use the version command in ROUTER RIP mode.
8.0.0.0/8 auto-summary 12.0.0.0/8 [120/1] via 29.10.10.12, 00:00:26, Fa 12.0.0.0/8 auto-summary 20.0.0.0/8 [120/1] via 29.10.10.12, 00:00:26, Fa 20.0.0.0/8 auto-summary 29.10.10.0/24 directly connected,Fa 1/49 29.0.0.0/8 auto-summary 31.0.0.0/8 [120/1] via 29.10.10.12, 00:00:26, Fa 31.0.0.0/8 auto-summary 192.162.2.0/24 [120/1] via 29.10.10.12, 00:01:21, Fa 192.162.2.0/24 auto-summary 192.161.1.0/24 [120/1] via 29.10.10.12, 00:00:27, Fa 192.161.1.0/24 auto-summary 192.162.3.0/24 [120/1] via 29.10.10.
ROUTER RIP mode • distribute-list prefix-list-name in Assign a configured prefix list to all outgoing RIP routes. ROUTER RIP mode distribute-list prefix-list-name out To view the current RIP configuration, use the show running-config command in EXEC mode or the show config command in ROUTER RIP mode. Adding RIP Routes from Other Instances In addition to filtering routes, you can add routes from other routing instances or protocols to the RIP process.
ip rip send version [1] [2] Examples of the RIP Process To see whether the version command is configured, use the show config command in ROUTER RIP mode. The following example shows the RIP configuration after the ROUTER RIP mode version command is set to RIPv2. When you set the ROUTER RIP mode version command, the interface (TenGigabitEthernet 1/1) participating in the RIP process is also set to send and receive RIPv2 (shown in bold).
Generating a Default Route Traffic is forwarded to the default route when the traffic’s network is not explicitly listed in the routing table. Default routes are not enabled in RIP unless specified. Use the default-information originate command in ROUTER RIP mode to generate a default route into RIP. In Dell Networking OS, default routes received in RIP updates from other routes are advertised if you configure the default-information originate command. • Specify the generation of a default route in RIP.
ROUTER RIP mode offset-list access-list-name {in | out} offset [interface] Configure the following parameters: – prefix-list-name: the name of an established Prefix list to determine which incoming routes are modified – offset: the range is from 0 to 16. – interface: the type, slot, and number of an interface. To view the configuration changes, use the show config command in ROUTER RIP mode. Debugging RIP The debug ip rip command enables RIP debugging.
RIP Configuration on Core2 The following example shows how to configure RIPv2 on a host named Core2. Example of Configuring RIPv2 on Core 2 Core2(conf-if-te-2/3)# Core2(conf-if-te-2/3)#router rip Core2(conf-router_rip)#ver 2 Core2(conf-router_rip)#network 10.200.10.0 Core2(conf-router_rip)#network 10.300.10.0 Core2(conf-router_rip)#network 10.11.10.0 Core2(conf-router_rip)#network 10.11.20.0 Core2(conf-router_rip)#show config ! router rip network 10.0.0.
C 10.11.20.0/24 R 10.11.30.0/24 C 10.200.10.0/24 C 10.300.10.0/24 R 192.168.1.0/24 R 192.168.2.0/24 Core2# R 192.168.1.0/24 R 192.168.2.0/24 Direct, Te 2/3 via 10.11.20.1, Te 2/3 Direct, Te 2/4 Direct, Te 2/5 via 10.11.20.1, Te 2/3 via 10.11.20.1, Te 2/3 0/0 120/1 0/0 0/0 120/1 120/1 00:02:02 00:01:20 00:03:03 00:02:42 00:01:20 00:01:20 via 10.11.20.1, Te 2/3 via 10.11.20.
• To display Core 3 RIP activity, use the show ip protocols command. Examples of the show ip Commands to View Learned RIP Routes on Core 3 The following example shows the show ip rip database command to view the learned RIP routes on Core 3. Core3#show ip rip database Total number of routes in RIP database: 7 10.11.10.0/24 [120/1] via 10.11.20.2, 00:00:13, TenGigabitEthernet 10.200.10.0/24 [120/1] via 10.11.20.2, 00:00:13, TenGigabitEthernet 10.300.10.0/24 [120/1] via 10.11.20.
Routing Information Sources: Gateway Distance Last Update 10.11.20.2 120 00:00:22 Distance: (default is 120) Core3# RIP Configuration Summary Examples of Viewing RIP Configuration on Core 2 and Core 3 The following example shows viewing the RIP configuration on Core 2. ! interface TenGigabitEthernet ip address 10.11.10.1/24 no shutdown ! interface TenGigabitEthernet ip address 10.11.20.2/24 no shutdown ! interface TenGigabitEthernet ip address 10.200.10.
40 Remote Monitoring (RMON) Remote monitoring (RMON) is supported on Dell Networking OS. RMON is an industry-standard implementation that monitors network traffic by sharing network monitoring information. RMON provides both 32-bit and 64-bit monitoring facility and long-term statistics collection on Dell Networking Ethernet interfaces. RMON operates with the simple network management protocol (SNMP) and monitors all nodes on a local area network (LAN) segment.
Setting the rmon Alarm To set an alarm on any MIB object, use the rmon alarm or rmon hc-alarm command in GLOBAL CONFIGURATION mode. • Set an alarm on any MIB object.
– number: assign an event number in integer format from 1 to 65535. The number value must be unique in the RMON event table. – log: (Optional) enter the keyword log to generate an RMON event log, it sets the eventType to either log or log-andsnmptrap in the RMON event table. The default is None. – trap community: (Optional) enter the keyword trap and SNMP community string to generate SNMP traps for an RMON event entry, it sets the eventType to either snmptrap or log-and-snmptrap in the RMON event table.
– integer: a value from 1 to 65,535 that identifies the RMON group of statistics. The value must be a unique index in the RMON History Table. – owner: (Optional) specifies the name of the owner of the RMON group of statistics. The default is a null-terminated string. – ownername: (Optional) records the name of the owner of the RMON group of statistics. – buckets: (Optional) specifies the maximum number of buckets desired for the RMON collection history group of statistics.
41 Rapid Spanning Tree Protocol (RSTP) Rapid spanning tree protocol (RSTP) is supported on Dell Networking OS. Protocol Overview RSTP is a Layer 2 protocol — specified by IEEE 802.1w — that is essentially the same as spanning-tree protocol (STP) but provides faster convergence and interoperability with switches configured with STP and multiple spanning tree protocol (MSTP). The Dell Networking OS supports three other variations of spanning tree, as shown in the following table. Table 65.
• Adding a group of ports to a range of VLANs sends multiple messages to the rapid spanning tree protocol (RSTP) task, avoid using the range command. When using the range command, Dell Networking recommends limiting the range to five ports and 40 VLANs. RSTP and VLT Virtual link trunking (VLT) provides loop-free redundant topologies and does not require RSTP. RSTP can cause temporary port state blocking and may cause topology changes after link or node failures.
• Bridges block a redundant path by disabling one of the link ports. To enable RSTP globally for all Layer 2 interfaces, use the following commands. 1. Enter PROTOCOL SPANNING TREE RSTP mode. CONFIGURATION mode protocol spanning-tree rstp 2. Enable RSTP. PROTOCOL SPANNING TREE RSTP mode no disable Examples of the RSTP show Commands To disable RSTP globally for all Layer 2 interfaces, enter the disable command from PROTOCOL SPANNING TREE RSTP mode.
Configured hello time 2, max age 20, forward delay 15, max hops 0 We are the root Current root has priority 32768, Address 0001.e801.cbb4 Number of topology changes 4, last change occurred 00:02:17 ago on Te 1/26 Port 377 (TenGigabitEthernet 2/1) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.377 Designated root has priority 32768, address 0001.e801.cbb4 Designated bridge has priority 32768, address 0001.e801.cbb4 Designated port id is 128.
Adding and Removing Interfaces To add and remove interfaces, use the following commands. To add an interface to the Rapid Spanning Tree topology, configure it for Layer 2 and it is automatically added. If you previously disabled RSTP on the interface using the command no spanning-tree 0 command, re-enable it using the spanning-tree 0 command. • Remove an interface from the Rapid Spanning Tree topology. no spanning-tree 0 Modifying Global Parameters You can modify RSTP parameters.
PROTOCOL SPANNING TREE RSTP mode hello-time seconds NOTE: With large configurations (especially those configurations with more ports) Dell Networking recommends increasing the hello-time. The range is from 1 to 10. • The default is 2 seconds. Change the max-age parameter. PROTOCOL SPANNING TREE RSTP mode max-age seconds The range is from 6 to 40. The default is 20 seconds. To view the current values for global parameters, use the show spanning-tree rstp command from EXEC privilege mode.
Enabling SNMP Traps for Root Elections and Topology Changes To enable SNMP traps collectively, use this command. Enable SNMP traps for RSTP, MSTP, and PVST+ collectively. snmp-server enable traps xstp Influencing RSTP Root Selection RSTP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it is selected as the root bridge. To change the bridge priority, use the following command.
– Disable the shutdown-on-violation command on the interface (the no spanning-tree stp-id portfast [bpduguard | [shutdown-on-violation]] command). – Disable spanning tree on the interface (the no spanning-tree command in INTERFACE mode). – Disable global spanning tree (the no spanning-tree command in CONFIGURATION mode). To enable EdgePort on an interface, use the following command. • Enable EdgePort on an interface.
42 Software-Defined Networking (SDN) Dell Networking operating software supports Software-Defined Networking (SDN). For more information, refer to the SDN Deployment Guide.
43 Security Security features are supported on Dell Networking OS. This chapter describes several ways to provide security to the Dell Networking system. For details about all the commands described in this chapter, refer to the Security chapter in the Dell Networking OS Command Reference Guide. AAA Accounting Accounting, authentication, and authorization (AAA) accounting is part of the AAA security model.
– suppress: Do not generate accounting records for a specific type of user. – default | name: enter the name of a list of accounting methods. – start-stop: use for more accounting information, to send a start-accounting notice at the beginning of the requested event and a stop-accounting notice at the end. – wait-start: ensures that the TACACS+ security server acknowledges the start notice before granting the user's process request.
Monitoring AAA Accounting Dell Networking OS does not support periodic interim accounting because the periodic command can cause heavy congestion when many users are logged in to the network. No specific show command exists for TACACS+ accounting. To obtain accounting records displaying information about users currently logged in, use the following command. • Step through all active sessions and print all the accounting records for the actively accounted functions.
Configuring AAA Authentication Login Methods To configure an authentication method and method list, use the following commands. Dell Networking OS Behavior: If you use a method list on the console port in which RADIUS or TACACS is the last authentication method, and the server is not reachable, Dell Networking OS allows access even though the username and password credentials cannot be verified.
Enabling AAA Authentication — RADIUS To enable authentication from the RADIUS server, and use TACACS as a backup, use the following commands. 1. Enable RADIUS and set up TACACS as backup. CONFIGURATION mode aaa authentication enable default radius tacacs 2. Establish a host address and password. CONFIGURATION mode radius-server host x.x.x.x key some-password 3. Establish a host address and password. CONFIGURATION mode tacacs-server host x.x.x.
Password obscuring masks the password and keys for display only but does not change the contents of the file. The string of asterisks is the same length as the encrypted string for that line of configuration. To verify that you have successfully obscured passwords and keys, use the show running-config command or show startup-config command. If you are using role-based access control (RBAC), only the system administrator and security administrator roles can enable the service obscure-password command.
Configuration Task List for Privilege Levels The following list has the configuration tasks for privilege levels and passwords.
To view the configuration for the enable secret command, use the show running-config command in EXEC Privilege mode. In custom-configured privilege levels, the enable command is always available. No matter what privilege level you entered Dell Networking OS, you can enter the enable 15 command to access and configure all CLIs.
• reset: return the command to its default privilege mode. Examples of Privilege Level Commands To view the configuration, use the show running-config command in EXEC Privilege mode. The following example shows a configuration to allow a user john to view only EXEC mode commands and all snmp-server commands.
Specifying LINE Mode Password and Privilege You can specify a password authentication of all users on different terminal lines. The user’s privilege level is the same as the privilege level assigned to the terminal line, unless a more specific privilege level is assigned to the user. To specify a password for the terminal line, use the following commands. • Configure a custom privilege level for the terminal lines. LINE mode privilege level level • – level level: The range is from 0 to 15.
Transactions between the RADIUS server and the client are encrypted (the users’ passwords are not sent in plain text). RADIUS uses UDP as the transport protocol between the RADIUS server host and the client. For more information about RADIUS, refer to RFC 2865, Remote Authentication Dial-in User Service.
• Monitoring RADIUS (optional) For a complete listing of all Dell Networking OS commands related to RADIUS, refer to the Security chapter in the Dell Networking OS Command Reference Guide. NOTE: RADIUS authentication and authorization are done in a single step. Hence, authorization cannot be used independent of authentication. However, if you have configured RADIUS authorization and have not configured authentication, a message is logged stating this.
CONFIGURATION mode radius-server host {hostname | ip-address} [auth-port port-number] [retransmit retries] [timeout seconds] [key [encryption-type] key] Configure the optional communication parameters for the specific host: – auth-port port-number: the range is from 0 to 65535. Enter a UDP port number. The default is 1812. – retransmit retries: the range is from 0 to 100. Default is 3. – timeout seconds: the range is from 0 to 1000. Default is 5 seconds.
– seconds: the range is from 0 to 1000. Default is 5 seconds. To view the configuration of RADIUS communication parameters, use the show running-config command in EXEC Privilege mode. Monitoring RADIUS To view information on RADIUS transactions, use the following command. • View RADIUS transactions to troubleshoot problems. EXEC Privilege mode debug radius TACACS+ Dell Networking OS supports terminal access controller access control system (TACACS+ client, including support for login authentication.
4. Assign the method-list to the terminal line. LINE mode login authentication {method-list-name | default} Example of a Failed Authentication To view the configuration, use the show config in LINE mode or the show running-config tacacs+ command in EXEC Privilege mode. If authentication fails using the primary method, Dell Networking OS employs the second method (or third method, if necessary) automatically.
Example of Specifying a TACACS+ Server Host Dell(conf)# Dell(conf)#aaa authentication login tacacsmethod tacacs+ Dell(conf)#aaa authentication exec tacacsauthorization tacacs+ Dell(conf)#tacacs-server host 25.1.1.2 key Force Dell(conf)# Dell(conf)#line vty 0 9 Dell(config-line-vty)#login authentication tacacsmethod Dell(config-line-vty)#end Specifying a TACACS+ Server Host To specify a TACACS+ server host and configure its communication parameters, use the following command.
Protection from TCP Tiny and Overlapping Fragment Attacks Tiny and overlapping fragment attack is a class of attack where configured ACL entries — denying TCP port-specific traffic — is bypassed and traffic is sent to its destination although denied by the ACL. RFC 1858 and 3128 proposes a countermeasure to the problem. This countermeasure is configured into the line cards and enabled by default.
To disable SSH server functions, use the no ip ssh server enable command. Using SCP with SSH to Copy a Software Image To use secure copy (SCP) to copy a software image through an SSH connection from one switch to another, use the following commands. On the chassis, invoke SCP.
Configuring the SSH Server Key Exchange Algorithm To configure the key exchange algorithm for the SSH server, use the ip ssh server kex key-exchange-algorithm command in CONFIGURATION mode. key-exchange-algorithm : Enter a space-delimited list of key exchange algorithms that will be used by the SSH server.
• hmac-sha2-256-96 When FIPS is enabled, the default HMAC algorithm is hmac-sha1-96. Example of Configuring a HMAC Algorithm The following example shows you how to configure a HMAC algorithm list. Dell(conf)# ip ssh server mac hmac-sha1-96 Configuring the SSH Server Cipher List To configure the cipher list supported by the SSH server, use the ip ssh server cipher cipher-list command in CONFIGURATION mode. cipher-list-: Enter a space-delimited list of ciphers the SSH server will support.
SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmac-sha2-256,hmacsha2-256-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffie-hellman-group1sha1,diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled.
no ip ssh password-authentication or no ip ssh rsa-authentication 6. Enable host-based authentication. CONFIGURATION mode ip ssh hostbased-authentication enable 7. Bind shosts and rhosts to host-based authentication. CONFIGURATION mode ip ssh pub-key-file flash://filename or ip ssh rhostsfile flash://filename Examples of Creating shosts and rhosts The following example shows creating shosts. admin@Unix_client# cd /etc/ssh admin@Unix_client# ls moduli sshd_config ssh_host_dsa_key.pub ssh_host_key.
Troubleshooting SSH To troubleshoot SSH, use the following information. You may not bind id_rsa.pub to RSA authentication while logged in via the console. In this case, this message displays:%Error: No username set for this term. Enable host-based authentication on the server (Dell Networking system) and the client (Unix machine). The following message appears if you attempt to log in via SSH and host-based is disabled on the client.
2. Enter a password. 3. Assign an access class. 4. Enter a privilege level. You can assign line authentication on a per-VTY basis; it is a simple password authentication, using an access-class as authorization. Configure local authentication globally and configure access classes on a per-user basis. Dell Networking OS can assign different access classes to different users by username. Until users attempt to log in, Dell Networking OS does not know if they will be assigned a VTY line.
The following example shows how to deny incoming connections from subnet 10.0.0.0 without displaying a login prompt.
A constrained RBAC model provides for separation of duty and as a result, provides greater security than the hierarchical RBAC model. Essentially, a constrained model puts some limitations around each role’s permissions to allow you to partition of tasks. However, some inheritance is possible. Default command permissions are based on CLI mode (such as configure, interface, router), any specific command settings, and the permissions allowed by the privilege and role commands.
If you do not, the following error is displayed when you attempt to enable role-based only AAA authorization. % Error: Exec authorization must be applied to more than one line to be useful, e.g. console and vty lines. Could use default authorization method list as alternative. 5. Verify the configuration has been applied to the console or VTY line.
• Modifying Command Permissions for Roles • Adding and Deleting Users from a Role Creating a New User Role Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you can first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role’s command permissions from scratch. You then restrict commands or add commands to that role.
Modifying Command Permissions for Roles You can modify (add or delete) command permissions for newly created user roles and system defined roles using the role mode { { { addrole | deleterole } role-name } | reset } command command in Configuration mode. NOTE: You cannot modify system administrator command permissions. If you add or delete command permissions using the role command, those changes only apply to the specific user role. They do not apply to other roles that have inheritance from that role.
Dell(conf)#show role mode configure interface Role access: netadmin, secadmin, sysadmin Example: Verify that the Security Administrator Can Access Interface Mode The following example shows that the secadmin role can now access Interface mode (highlighted in bold).
NOTE: If you already have a user ID that exists with a privilege level, you can add the user role to username that has a privilege Dell (conf) #no username john The following example adds a user, to the secadmin user role. Dell (conf)#username john role secadmin password 0 password AAA Authentication and Authorization for Roles This section describes how to configure AAA Authentication and Authorization for Roles.
You can further restrict users’ permissions, using the aaa authorization command command in CONFIGURATION mode. aaa authorization command {method-list-name | default} method [… method4] Examples of Applying a Method List The following configuration example applies a method list: TACACS+, RADIUS and local: ! radius-server host 10.16.150.203 key ! tacacs-server host 10.16.150.
Configuring TACACS+ and RADIUS VSA Attributes for RBAC For RBAC and privilege levels, the Dell Networking OS RADIUS and TACACS+ implementation supports two vendor-specific options: privilege level and roles. The Dell Networking vendor-ID is 6027 and the supported option has attribute of type string, which is titled “Force10-avpair”.
The following example shows you how to configure AAA accounting to monitor commands executed by the users who have a secadmin user role. Dell(conf)#aaa accounting command role secadmin default start-stop tacacs+ Applying an Accounting Method to a Role To apply an accounting method list to a role executed by a user with that user role, use the accounting command in LINE mode.
Displaying Role Permissions Assigned to a Command To display permissions assigned to a command, use the show role command in EXEC Privilege mode. The output displays the user role and or permission level.
44 Service Provider Bridging Service provider bridging is supported on Dell Networking OS. VLAN Stacking VLAN stacking, also called Q-in-Q, is defined in IEEE 802.1ad — Provider Bridges, which is an amendment to IEEE 802.1Q — Virtual Bridged Local Area Networks. It enables service providers to use 802.1Q architecture to offer separate VLANs to customers with no coordination between customers, and minimal coordination between customers and the provider. Using only 802.
Figure 104. VLAN Stacking in a Service Provider Network Important Points to Remember • Interfaces that are members of the Default VLAN and are configured as VLAN-Stack access or trunk ports do not switch untagged traffic. To switch traffic, add these interfaces to a non-default VLAN-Stack-enabled VLAN. • Dell Networking cautions against using the same MAC address on different customer VLANs, on the same VLAN-Stack VLAN.
Related Configuration Tasks • Configuring the Protocol Type Value for the Outer VLAN Tag • Configuring Dell Networking OS Options for Trunk Ports • Debugging VLAN Stacking • VLAN Stacking in Multi-Vendor Networks Creating Access and Trunk Ports To create access and trunk ports, use the following commands. • Access port — a port on the service provider edge that directly connects to the customer. An access port may belong to only one service provider VLAN.
Example of Viewing VLAN Stack Member Status To display the status and members of a VLAN, use the show vlan command from EXEC Privilege mode. Members of a VLANStacking-enabled VLAN are marked with an M in column Q.
switchport vlan-stack trunk shutdown Dell(conf-if-te-1/1)#interface vlan 100 Dell(conf-if-vl-100)#untagged tengigabitethernet 1/1 Dell(conf-if-vl-100)#interface vlan 101 Dell(conf-if-vl-101)#tagged tengigabitethernet 1/1 Dell(conf-if-vl-101)#interface vlan 103 Dell(conf-if-vl-103)#vlan-stack compatible Dell(conf-if-vl-103-stack)#member tengigabitethernet 1/1 Dell(conf-if-vl-103-stack)#do show vlan Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP
VLAN Stacking The default TPID for the outer VLAN tag is 0x9100. The system allows you to configure both bytes of the 2 byte TPID. Previous versions allowed you to configure the first byte only, and thus, the systems did not differentiate between TPIDs with a common first byte. For example, 0x8100 and any other TPID beginning with 0x81 were treated as the same TPID, as shown in the following illustration. Dell Networking OS Versions 8.2.1.
Figure 105.
Figure 106.
Figure 107. Single and Double-Tag TPID Mismatch VLAN Stacking Packet Drop Precedence The drop eligible indicator (DEI) bit in the S-Tag indicates to a service provider bridge which packets it should prefer to drop when congested. Enabling Drop Eligibility Enable drop eligibility globally before you can honor or mark the DEI value. When you enable drop eligibility, DEI mapping or marking takes place according to the defaults. In this case, the CFI is affected according to the following table. Table 68.
Ingress Egress DEI Disabled DEI Enabled Access Port Trunk Port Retain inner tag CFI Retain inner tag CFI Set outer tag CFI to 0 Set outer tag CFI to 0 To enable drop eligibility globally, use the following command. • Make packets eligible for dropping based on their DEI value. CONFIGURATION mode dei enable By default, packets are colored green, and DEI is marked 0 on egress.
Example of Viewing DEI-Marking Configuration To display the DEI-marking configuration, use the show interface dei-mark [interface slot/port | linecard number port-set number] in EXEC Privilege mode.
Examples of QoS Interface Configuration and Rate Policing policy-map-input in layer2 service-queue 3 class-map a qos-policy 3 ! class-map match-any a layer2 match mac access-group a ! mac access-list standard a seq 5 permit any ! qos-policy-input 3 layer2 rate-police 40 Likewise, in the following configuration, packets with dot1p priority 0–3 are marked as dot1p 7 in the outer tag and queued to Queue 3. Rate policing is according to qos-policy-input 3.
vlan-stack dot1p-mapping c-tag-dot1p values sp-tag-dot1p value Separate C-Tag values by commas. Dashed ranges are permitted. Dynamic Mode CoS overrides any Layer 2 QoS configuration in case of conflicts. NOTE: Because dot1p-mapping marks and queues packets, the only remaining applicable QoS configuration is rate metering. You may use Rate Shaping or Rate Policing.
You might need to transport control traffic transparently through the intermediate network to the other region. Layer 2 protocol tunneling enables BPDUs to traverse the intermediate network by identifying frames with the Bridge Group Address, rewriting the destination MAC to a user-configured non-reserved address, and forwarding the frames. Because the frames now use a unique MAC address, BPDUs are treated as normal data frames by the switches in the intermediate network core.
Implementation Information • • • L2PT is available for STP, RSTP, MSTP, and PVST+ BPDUs. No protocol packets are tunneled when you enable VLAN stacking. L2PT requires the default CAM profile. Enabling Layer 2 Protocol Tunneling To enable Layer 2 protocol tunneling, use the following command. 1. Verify that the system is running the default CAM profile. Use this CAM profile for L2PT. EXEC Privilege mode show cam-profile 2. Enable protocol tunneling globally on the system.
4. Set a maximum rate at which the RPM processes BPDUs for L2PT. VLAN STACKING mode protocol-tunnel rate-limit The default is: no rate limiting. The range is from 64 to 320 kbps. Debugging Layer 2 Protocol Tunneling To debug Layer 2 protocol tunneling, use the following command. • Display debugging information for L2PT. EXEC Privilege mode debug protocol-tunnel Provider Backbone Bridging IEEE 802.1ad—Provider Bridges amends 802.
45 sFlow Configuring sFlow is supported on Dell Networking OS. Overview The Dell Networking Operating System (OS) supports sFlow version 5. sFlow is a standard-based sampling technology embedded within switches and routers which is used to monitor network traffic. It is designed to provide traffic monitoring for high-speed networks with many switches and routers. sFlow uses two types of sampling: • Statistical packet-based sampling of switched or routed packet flows.
• Community list and local preference fields are not filled in extended gateway element in the sFlow datagram. • 802.1P source priority field is not filled in extended switch element in sFlow datagram. • Only Destination and Destination Peer AS number are packed in the dst-as-path field in extended gateway element. • If the packet being sampled is redirected using policy-based routing (PBR), the sFlow datagram may contain incorrect extended gateway/router information.
Enabling and Disabling sFlow on an Interface By default, sFlow is disabled on all interfaces. This CLI is supported on physical ports and link aggregation group (LAG) ports. To enable sFlow on a specific interface, use the following command. • Enable sFlow on an interface. INTERFACE mode [no] sflow ingress-enable To disable sFlow on an interface, use the no version of this command.
Example of the show running-config sflow Command Dell#show running-config sflow ! sflow collector 100.1.1.12 agent-addr 100.1.1.1 sflow enable sflow max-header-size extended Dell#show run int tengigabitEthernet 1/10 ! interface TenGigabitEthernet 1/10 no ip address switchport sflow ingress-enable sflow max-header-size extended no shutdown sFlow Show Commands Dell Networking OS includes the following sFlow display commands.
show sflow interface interface-name Examples of the sFlow show Commands The following example shows the show sflow interface command. Dell#show sflow interface tengigabitethernet 1/1 Te 1/1 sFlow type :Ingress Configured sampling rate :16384 Actual sampling rate :16384 Counter polling interval :20 Extended max header size :128 Samples rcvd from h/w :0 The following example shows the show running-config interface command.
Changing the Polling Intervals The sflow polling-interval command configures the polling interval for an interface in the maximum number of seconds between successive samples of counters sent to the collector. This command changes the global default counter polling (20 seconds) interval. You can configure an interface to use a different polling interval. To configure the polling intervals globally (in CONFIGURATION mode) or by interface (in INTERFACE mode), use the following command.
Examples of Verifying Extended sFlow The bold line shows that extended sFlow settings are enabled on all three types. Dell#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header size: 128 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.1, Agent IP addr: 1.1.1.
IP SA IP DA srcAS and srcPeerAS dstAS and dstPeerAS Description IP DA is not learned via BGP. Version 7.8.1.0 allows extended gateway information in cases where the source and destination IP addresses are learned by different routing protocols, and for cases where is source is reachable over ECMP. BGP BGP Exported Exported Extended gateway data is packed.
46 Simple Network Management Protocol (SNMP) Simple network management protocol (SNMP) is supported on Dell Networking OS. NOTE: On Dell Networking routers, standard and private SNMP management information bases (MIBs) are supported, including all Get and a limited number of Set operations (such as set vlan and copy cmd). Protocol Overview Network management stations use SNMP to retrieve or alter management data from network elements.
FIPS Mode Privacy Options Authentication Options Disabled des56 md5 (HMAC-MD5-96) Enabled (DES56-CBC) aes128 (AES128-CFB) sha (HMAC-SHA1-96) aes128 (AES128-CFB) sha (HMAC-SHA1-96) To enable security for SNMP packets transferred between the server and the client, you can use the snmp-server user username group groupname 3 auth authentication-type auth-password priv aes128 priv-password command to specify that AES-CFB 128 encryption algorithm needs to be used.
• Copying Configuration Files via SNMP • Manage VLANs Using SNMP • Enabling and Disabling a Port using SNMP • Fetch Dynamic MAC Entries using SNMP • Deriving Interface Indices • Monitor Port-channels Important Points to Remember • Typically, 5-second timeout and 3-second retry values on an SNMP server are sufficient for both LAN and WAN applications.
Setting Up User-Based Security (SNMPv3) When setting up SNMPv3, you can set users up with one of the following three types of configuration for SNMP read/write operations. Users are typically associated to an SNMP group with permissions provided, such as OID view. • noauth — no password or privacy. Select this option to set up a user with no password or privacy privileges. This setting is the basic configuration. Users must have a group and profile that do not require password privileges.
Select a User-based Security Type Dell(conf)#snmp-server host 1.1.1.1 traps {oid tree} version 3 ? auth Use the SNMPv3 authNoPriv Security Level noauth Use the SNMPv3 noAuthNoPriv Security Level priv Use the SNMPv3 authPriv Security Level Dell(conf)#snmp-server host 1.1.1.1 traps {oid tree} version 3 noauth ? WORD SNMPv3 user name Reading Managed Object Values You may only retrieve (read) managed object values if your management station is a member of the same community as the SNMP agent.
Example of Writing the Value of a Managed Object > snmpset -v 2c -c mycommunity 10.11.131.161 sysName.0 s "R5" SNMPv2-MIB::sysName.0 = STRING: R5 Configuring Contact and Location Information using SNMP You may configure system contact and location information from the Dell Networking system or from the management station using SNMP. To configure system contact and location information from the Dell Networking system and from the management station using SNMP, use the following commands.
• Force10 enterpriseSpecific protocol traps — bgp, ecfm, stp, and xstp. To configure the system to send SNMP notifications, use the following commands. 1. Configure the Dell Networking system to send notifications to an SNMP server. CONFIGURATION mode snmp-server host ip-address [traps | informs] [version 1 | 2c |3] [community-string] To send trap messages, enter the keyword traps. To send informational messages, enter the keyword informs.
Example of Dell Networking Enterprise-specific SNMP Traps envmon STACK_STATE: Stack unit %d is in Active State STACKUNITUP: Stack unit 0 is up envmon CARD_SHUTDOWN: %sLine card %d down - %s CARD_DOWN: %sLine card %d down - %s LINECARDUP: %sLine card %d is up CARD_MISMATCH: Mismatch: line card %d is type %s - type %s required.
%SPANMGR-5-MSTP_TOPOLOGY_CHANGE: Topology change BridgeAddr: 0001.e801.fc35 Mstp Instance Id 0 port Te 1/8 transitioned from forwarding to discarding state.
Table 70. List of Syslog Server MIBS that have read access MIB Object OID Object Values Description dF10SysLogTraps 1.3.6.1.4.1.6027.3.30.1.1 1 = reachable2 = unreachable Specifies whether the syslog server is reachable or unreachable. Following example shows the SNMP trap that is sent when connectivity to the syslog server is lost: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (19738) 0:03:17.38 SNMPv2MIB::snmpTrapOID.0 = OID: SNMPv2SMI::enterprises.6027.3.30.1.1.1 SNMPv2-SMI::enterprises.6027.
MIB Object OID Object Values Description copySrcFileLocation and copySrcFileName. copySrcFileLocation .1.3.6.1.4.1.6027.3.5.1.1.1.1.3 1 = flash 2 = slot0 Specifies the location of source file. • 3 = tftp 4 = ftp If copySrcFileLocation is FTP or SCP, you must specify copyServerAddress, copyUserName, and copyUserPassword. 5 = scp 6 = usbflash copySrcFileName .1.3.6.1.4.1.6027.3.5.1.1.1.1.4 Path (if the file is not in the Specifies name of the file. current directory) and filename.
MIB Object OID Object Values Description copyUserPassword .1.3.6.1.4.1.6027.3.5.1.1.1.1.10 Password for the server. Password for the FTP, TFTP, or SCP server. Copying a Configuration File To copy a configuration file, use the following commands. NOTE: In UNIX, enter the snmpset command for help using the following commands. Place the f10-copy-config.mib file in the directory from which you are executing the snmpset command or in the snmpset tool path. 1.
Examples of Copying Configuration Files The following examples show the command syntax using MIB object names and the same command using the object OIDs. In both cases, a unique index number follows the object. The following example shows copying configuration files using MIB object names. > snmpset -v 2c -r 0 -t 60 -c private -m ./f10-copy-config.mib 10.10.10.10 copySrcFileType. 101 i 2 copyDestFileType.101 i 3 FTOS-COPY-CONFIG-MIB::copySrcFileType.
FTOS-COPY-CONFIG-MIB::copyServerAddress.110 = IpAddress: 11.11.11.11 FTOS-COPY-CONFIG-MIB::copyUserName.110 = STRING: mylogin FTOS-COPY-CONFIG-MIB::copyUserPassword.110 = STRING: mypass Copying the Startup-Config Files to the Server via TFTP To copy the startup-config to the server via TFTP from the UNIX machine, use the following command. NOTE: Verify that the file exists and its permissions are set to 777. Specify the relative path to the TFTP root directory.
MIB Object OID Values Description copyFailCause .1.3.6.1.4.1.6027.3.5.1.1.1.1.14 1 = bad filename Specifies the reason the copy request failed. 2 = copy in progress 3 = disk full 4 = file exists 5 = file not found 6 = timeout 7 = unknown copyEntryRowStatus .1.3.6.1.4.1.6027.3.5.1.1.1.1.15 Row status Specifies the state of the copy operation. Uses CreateAndGo when you are performing the copy. The state is set to active when the copy is completed.
MIB Support to Display the Available Memory Size on Flash Dell Networking provides more MIB objects to display the available memory size on flash memory. The following table lists the MIB object that contains the available memory size on flash memory. Table 73. MIB Objects for Displaying the Available Memory Size on Flash via SNMP MIB Object OID Description chStackUnitFlashUsageUtil 1.3.6.1.4.1.6027.3.10.1.2.9.1.6 Contains flash memory usage in percentage.
• To view the viewing the software core files generated by the system, use the following command. snmpwalk -v2c -c public 192.168.60.120 .1.3.6.1.4.1.6027.3.10.1.2.10 enterprises.6027.3.10.1.2.10.1.1.1.1 = 1 enterprises.6027.3.10.1.2.10.1.1.1.2 = 2 enterprises.6027.3.10.1.2.10.1.1.1.3 = 3 enterprises.6027.3.10.1.2.10.1.1.2.1 = 1 enterprises.6027.3.10.1.2.10.1.2.1.1 = "/CORE_DUMP_DIR/flashmntr.core.gz" enterprises.6027.3.10.1.2.10.1.2.1.2 = "/CORE_DUMP_DIR/FTP_STK_MEMBER/ f10cp_l2mgr_131108080758_Stk1.
Displaying the Ports in a VLAN Dell Networking OS identifies VLAN interfaces using an interface index number that is displayed in the output of the show interface vlan command. Add Tagged and Untagged Ports to a VLAN The value dot1qVlanStaticEgressPorts object is an array of all VLAN members. The dot1qVlanStaticUntaggedPorts object is an array of only untagged VLAN members. All VLAN members that are not in dot1qVlanStaticUntaggedPorts are tagged.
• Set the amount of time after an IS-IS reload is performed before ingress traffic is allowed at startup. set-overload-bit on-startup isis The following OIDs are configurable through the snmpset command. The node OID is 1.3.6.1.4.1.6027.3.
Table 75. MIB Objects for Fetching Dynamic MAC Entries in the Forwarding Database MIB Object OID MIB Description dot1dTpFdbTable .1.3.6.1.2.1.17.4.3 Q-BRIDGE MIB List the learned unicast MAC addresses on the default VLAN. dot1qTpFdbTable .1.3.6.1.2.1.17.7.1.2. 2 Q-BRIDGE MIB List the learned unicast MAC addresses on non-default VLANs. dot3aCurAggFdb Table .1.3.6.1.4.1.6027.3.2. 1.1.5 F10-LINK-AGGREGATION MIB List the learned MAC addresses of aggregated links (LAG).
Deriving Interface Indices Dell Networking OS assigns an interface number to each (configured or unconfigured) physical and logical interface. The interface index is a binary number with bits that indicate the slot number, port number, interface type, and card type of the interface. Dell Networking OS converts this binary index number to decimal, and displays it in the output of the show interface command.
Monitor Port-Channels To check the status of a Layer 2 port-channel, use f10LinkAggMib (.1.3.6.1.4.1.6027.3.2). In the following example, Po 1 is a switchport and Po 2 is in Layer 3 mode. Example of SNMP Trap for Monitored Port-Channels [senthilnathan@lithium ~]$ snmpwalk -v 2c -c public 10.11.1.1 .1.3.6.1.4.1.6027.3.2.1.1 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.1 = INTEGER: 1 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.2 = INTEGER: 2 SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.
SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_UP: Changed interface state to up: Po 1" Troubleshooting SNMP Operation When you use SNMP to retrieve management data from an SNMP agent on a Dell Networking router, take into account the following behavior. • When you query an IPv4 icmpMsgStatsInPkts object in the ICMP table by using the snmpwalk command, the output for echo replies may be incorrectly displayed.
47 Stacking Stacking is supported on the S6000 platform with the Dell Networking Operating System (OS) version 9.7(0.0) NOTE: The S6000 commands accept Unit ID numbers 0-11, though the S6000 supports stacking up to 6 units with Dell Networking OS version 9.7(0.0). Using the Dell Networking OS stacking feature, you can interconnect multiple S-Series switch units with dedicated stacking ports or front end user ports.
Stack Master Election The stack elects a master and standby unit at bootup time based on two criteria. • Unit priority — User-configurable. The range is from 1 to 14. A higher value (14) means a higher priority. The default is 1. By removing the stack-unit priority using the no stack-unit priority command, you can set the priority back to the default value of zero.
2 2 5 5 5 1 2 0 1 2 up up up up up up up up up up 7072 7021 7072 7021 7072 up up up up up 7021 7021 7021 6971 7021 Speed in RPM Dell# Virtual IP You can manage the stack using a single IP, known as a virtual IP, that is retained in the stack even after a failover. The virtual IP address is used to log in to the current master unit of the stack. Both IPv4 and IPv6 addresses are supported as virtual IPs.
[output omitted] Standalone#show system | grep priority Master priority : 0 -----------STACK BEFORE CONNECTION---------------Stack#show system brief Stack MAC : 00:01:e8:d5:f9:6f -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports --------------------------------------------------0 Standby online S6000 1-0 (0-3387) 128 1 Management online S6000 1-0 (0-3387) 128 2 Member not present 3 Member not present 4 Member not present 5 Member not present 6 Member not present 7 Member not present [output om
• Shortest path selection inside the stack: If multiple paths exist between two units in the stack, the shortest path is used. Supported Stacking Topologies The device supports stacking in a ring or a daisy chain topology. Dell Networking recommends the ring topology when stacking the switches to provide redundant connectivity. Figure 111.
Stack-unit SW Version: 1-0(0-3387) -- Stack-unit Redundancy Configuration ------------------------------------------------Primary Stack-unit: mgmt-id 0 Auto Data Sync: Full Failover Type: Hot Failover Auto reboot Stack-unit: Disabled Auto failover limit: 3 times in 60 minutes -- Stack-unit Failover Record ------------------------------------------------Failover Count: 0 Last failover timestamp: None Last failover Reason: None Last failover type: None -- Last Data Block Sync Record: -----------------------
You can connect two units with two or more stacking cables in case of a stacking port or cable failure. Removal of only one of the cables does not trigger a reset. Important Points to Remember • You may stack up to six S6000 systems. • The S6000 cannot be stacked with other system types. • You cannot enable stacking and virtual link trunking (VLT) simultaneously on the device. To convert a stacked unit to VLT, refer to Reconfiguring Stacked Switches as VLT.
When a unit is added to a stack, the management unit performs a system check on the new unit to ensure the hardware type is compatible. A similar check is performed on the Dell Networking OS version. If the stack is running Dell Networking OS version9.7.0.0and the new unit is running an earlier software version, the new unit is put into a card problem state. • If the unit is running Dell Networking OS version 9.7.0.
The new unit synchronizes its running and startup configurations with the stack. 4. After the units are reloaded, the system reboots. The units come up in a stack after the reboot completes. To view the port assignments, use the show system stack-unit command. Creating a New Stack Prior to creating a stack, know which unit will be the management unit and which will be the standby unit. Enable the front ports of the units for stacking. For more information, refer to Enabling Front End Port Stacking.
Example of a Syslog Figure 113. Creating a new stack In the following example, stack unit is the master management unit, stack unit 2is the standby unit. The cables are connected to each unit.
Stack MAC Reload-Type : 90:b1:1c:f4:a7:c7 : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Member not present S6000 1 Member not present 2 Standby online S6000 S6000 1-0(0-3387) 128 3 Member not present S6000 4 Member not present 5 Management online S6000 S6000 1-0(0-3387) 128 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ------------------------
stack-unit [0–5] renumber [0–5] 3. (OPTIONAL) On the new unit, assign a management priority based on whether you want the new unit to be the stack manager. CONFIGURATION mode stack-unit [0–5] priority [1–14] 4. Assign a stack group to each unit. CONFIGURATION mode stack-unitstack-unit-number stack-group stack-group-number 5. Connect the new unit to the stack using stacking cables.
5. • Dell# configure Configure the ports on the added switch for stacking. CONFIGURATION mode stack-unit 0 stack-group group-number 6. • stack-unit 0: defines the default ID unit-number in the initial configuration of a switch. • stack-group group-number: configures a port for stacking. Save the stacking configuration on the ports. EXEC Privilege mode write memory 7. Reload the switch.
• If one of the new stacks receives only the standby unit, it becomes the master unit of the new stack, and Dell Networking OS elects a new standby unit. • If one of the new stacks receives neither the master nor the standby management unit, the stack is reset so that a new election can take place. S-Series Stacking Configuration Tasks The following are configuration tasks for the S-Series.
• Display the same information in show system, but only for the specified unit. EXEC Privilege mode show system stack-unit • Refer to the following example. Display topology and stack link status for the entire stack. EXEC Privilege mode show system stack-ports [status | topology] Refer to the following example. Examples of the show system Commands Display information about an stack using the show system command. The following is an example of the show system command to view the stack details.
POE Capable FIPS Mode Burned In MAC No Of MACs : : : : no disabled 90:b1:1c:f4:a7:c7 3 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------5 0 up AC up 6688 5 1 down UNKNOWN down 0 -- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed -----------------------------------------------------------------------------------5 0 up up 6971 up 7072 5 1 up up 7072 up 6971 5 2 up up 6971 up 7021 Speed in RPM Dell# The following
5/4 5/120 Dell# 2/4 42 42 up up down up Influencing Management Unit Selection on an S-Series Stack Stack priority is the system variable that Dell Networking OS uses to determine which units in the stack are the master and standby management units. If multiple units tie for highest priority, the unit with the highest MAC address prevails. If management was determined by priority only, a change in management occurs when: • the management unit is powered down or a failover occurs.
EXEC Privilege mode • reset stack-unit Reload a member unit, from the unit itself. EXEC Privilege mode • reset-self Reset a stack-unit when the unit is in a problem state. EXEC Privilege mode reset stack-unit {hard} Verify a Stack Configuration The light of the LED status indicator on the front panel of the stack identifies the unit’s role in the stack. • Off indicates the unit is a stack member. • Blinking green indicates the unit is the stack standby.
Jumbo Capable POE Capable FIPS Mode Boot Flash Boot Selector Memory Size Temperature Voltage Serial Number Part Number Vendor Id Date Code Country Code Piece Part ID PPID Revision Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : : : : : : : : : : : : : : : : yes no disabled 3.1.1.3 3.1.0.
Examples of Removing a Stack Member (Before and After) The following examples shows removing a stack member (before).
Recover from Stack Link Flaps S-Series stack link integrity monitoring enables units to monitor their own stack ports and disable any stack port that flaps five times within 10 seconds. Dell Networking OS displays console messages for the local and remote members of a flapping link, and on the primary (master) and standby management units as KERN-2-INT messages if the flapping port belongs to either of these units. In the following example, a stack-port on the master flaps.
-- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed -----------------------------------------------------------------------------------2 0 up up 7072 up 6971 2 1 up up 7021 up 7021 2 2 up up 7021 up 6971 5 0 up up 7021 up 7123 5 1 up up 6971 up 7021 5 2 up up 7021 up 6971 Speed in RPM 794 Stacking
48 Storm Control Storm control is supported on Dell Networking OS. The storm control feature allows you to control unknown-unicast and broadcast traffic on Layer 2 and Layer 3 physical interfaces. Dell Networking Operating System (OS) Behavior: Dell Networking OS supports broadcast control (the storm-control broadcast command) for Layer 2 and Layer 3 traffic. Configure Storm Control Storm control is supported in INTERFACE mode and CONFIGURATION mode.
49 Spanning Tree Protocol (STP) The spanning tree protocol (STP) is supported on Dell Networking OS. Protocol Overview STP is a Layer 2 protocol — specified by IEEE 802.1d — that eliminates loops in a bridged topology by enabling only a single path through the network. By eliminating loops, the protocol improves scalability in a large network and allows you to implement redundant paths, which can be activated after the failure of active paths.
• • To add interfaces to the spanning tree topology after you enable STP, enable the port and configure it for Layer 2 using the switchport command. The IEEE Standard 802.1D allows 8 bits for port ID and 8 bits for priority. The 8 bits for port ID provide port IDs for 256 ports. Configuring Interfaces for Layer 2 Mode All interfaces on all switches that participate in spanning tree must be in Layer 2 mode and enabled. Figure 114.
Example of the show config Command To verify that an interface is in Layer 2 mode and enabled, use the show config command from INTERFACE mode. Dell(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 no ip address switchport no shutdown Dell(conf-if-te-1/1)# Enabling Spanning Tree Protocol Globally Enable the spanning tree protocol globally; it is not enabled by default.
no disable Examples of Verifying Spanning Tree Information To disable STP globally for all Layer 2 interfaces, use the disable command from PROTOCOL SPANNING TREE mode. To verify that STP is enabled, use the show config command from PROTOCOL SPANNING TREE mode.
Te 1/4 Dell# 8.514 8 4 FWD 0 32768 0001.e80d.2462 8.514 Adding an Interface to the Spanning Tree Group To add a Layer 2 interface to the spanning tree topology, use the following command. • Enable spanning tree on a Layer 2 interface. INTERFACE mode spanning-tree 0 Modifying Global Parameters You can modify the spanning tree parameters. The root bridge sets the values for forward-delay, hello-time, and max-age and overwrites the values set on other bridges participating in STP.
• Change the max-age parameter (the refresh interval for configuration information that is generated by recomputing the spanning tree topology). PROTOCOL SPANNING TREE mode max-age seconds The range is from 6 to 40. The default is 20 seconds. To view the current values for global parameters, use the show spanning-tree 0 command from EXEC privilege mode. Refer to the second example in Enabling Spanning Tree Protocol Globally.
• Enable PortFast on an interface. INTERFACE mode spanning-tree stp-id portfast [bpduguard | [shutdown-on-violation]] Example of Verifying PortFast is Enabled on an Interface To verify that PortFast is enabled on a port, use the show spanning-tree command from EXEC Privilege mode or the show config command from INTERFACE mode. Dell Networking recommends using the show config command.
– Disabling global spanning tree (the no spanning-tree in CONFIGURATION mode). Figure 116. Enabling BPDU Guard Dell Networking OS Behavior: BPDU guard and BPDU filtering both block BPDUs, but are two separate features. BPDU guard: • is used on edgeports and blocks all traffic on edgeport if it receives a BPDU. • drops the BPDU after it reaches the RPM and generates a console message.
Te 1/6 Root 128.263 128 20000 FWD 20000 P2P No Te 1/7 ErrDis 128.264 128 20000 EDS 20000 P2P No Dell(conf-if-te-1/7)#do show ip interface brief tengigabitEthernet 1/7 Interface IP-Address OK Method Status Protocol TenGigabitEthernet 1/7 unassigned YES Manual up up Selecting STP Root The STP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it becomes the root bridge. You can also specify that a bridge is the root or the secondary root.
BPDU is ignored and the port on Switch C transitions from a forwarding to a root-inconsistent state (shown by the green X icon). As a result, Switch A becomes the root bridge. Figure 117. STP Root Guard Prevents Bridging Loops Configuring Root Guard Enable STP root guard on a per-port or per-port-channel basis.
– 0: enables root guard on an STP-enabled port assigned to instance 0. – mstp: enables root guard on an MSTP-enabled port. – rstp: enables root guard on an RSTP-enabled port. – pvst: enables root guard on a PVST-enabled port. To disable STP root guard on a port or port-channel interface, use the no spanning-tree 0 rootguard command in an interface configuration mode.
As shown in the following illustration (STP topology 2, upper right), a loop can also be created if the forwarding port on Switch B becomes busy and does not forward BPDUs within the configured forward-delay time. As a result, the blocking port on Switch C transitions to a forwarding state, and both Switch A and Switch C transmit traffic to Switch B (STP topology 2, lower right).
– Spanning Tree Protocol (STP) – Rapid Spanning Tree Protocol (RSTP) – Multiple Spanning Tree Protocol (MSTP) – Per-VLAN Spanning Tree Plus (PVST+) • You cannot enable root guard and loop guard at the same time on an STP port. For example, if you configure loop guard on a port on which root guard is already configured, the following error message is displayed: % Error: RootGuard is configured. Cannot configure LoopGuard.
50 System Time and Date System time and date settings and the network time protocol (NTP) are supported on Dell Networking OS. You can set system times and dates and maintained through the NTP. They are also set through the Dell Networking Operating System (OS) command line interfaces (CLIs) and hardware settings. In the release 9.4.(0.0), support for reaching an NTP server through different VRFs is included. You can configure a maximum of eight logging servers across different VRFs or the same VRF.
Dell Networking OS synchronizes with a time-serving host to get the correct time. You can set Dell Networking OS to poll specific NTP time-serving hosts for the current time. From those time-serving hosts, the system chooses one NTP host with which to synchronize and serve as a client to the NTP host. As soon as a host-client relationship is established, the networking device propagates the time information throughout its local network.
• Specify the NTP server to which the Dell Networking system synchronizes. CONFIGURATION mode ntp server ip-address Examples of Viewing System Clock To display the system clock state with respect to NTP, use the show ntp status command from EXEC Privilege mode. R6_E300(conf)#do show ntp status Clock is synchronized, stratum 2, reference is 192.168.1.1 frequency is -369.623 ppm, stability is 53.319 ppm, precision is 4294967279 reference time is CD63BCC2.0CBBD000 (16:54:26.
• Configure a source IP address for NTP packets. CONFIGURATION mode ntp source interface Enter the following keywords and slot/port or number information: – For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. – For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. – For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
ntp server [vrf] {hostname | ipv4-address |ipv6-address} [ key keyid] [prefer] [version number] Configure the IP address of a server and the following optional parameters: • – vrf-name : Enter the name of the VRF through which the NTP server is reachable. – hostname : Enter the keyword hostname to see the IP address or host name of the remote device. – ipv4-address : Enter an IPv4 address in dotted decimal format (A.B.C.D).
NOTE: • Leap Indicator (sys.leap, peer.leap, pkt.leap) — This is a two-bit code warning of an impending leap second to be inserted in the NTP time scale. The bits are set before 23:59 on the day of insertion and reset after 00:00 on the following day. This causes the number of seconds (rollover interval) in the day of insertion to be increased or decreased by one.
Setting the Time and Date for the Switch Software Clock You can change the order of the month and day parameters to enter the time and date as time day month year. You cannot delete the software clock. The software clock runs only when the software is up. The clock restarts, based on the hardware clock, when the switch reboots. To set the software clock, use the following command. • Set the system software clock to the current time and date.
Setting Daylight Saving Time Once Set a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. To set the clock for daylight savings time once, use the following command. • Set the clock to the appropriate timezone and daylight saving time. CONFIGURATION mode clock summer-time time-zone date start-month start-day start-year start-time end-month end-day end-year end-time [offset] – time-zone: enter the three-letter name for the time zone.
– start-month: Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. – start-day: Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. – start-year: Enter a four-digit number as the year. The range is from 1993 to 2035. – start-time: Enter the time in hours:minutes.
51 Tunneling Tunnel interfaces create a logical tunnel for IPv4 or IPv6 traffic. Tunneling supports RFC 2003, RFC 2473, and 4213. DSCP, hop-limits, flow label values, open shortest path first (OSPF) v2, and OSPFv3 are supported. Internet control message protocol (ICMP) error relay, PATH MTU transmission, and fragmented packets are not supported. Configuring a Tunnel You can configure a tunnel in IPv6 mode, IPv6IP mode, and IPIP mode.
Dell(conf-if-tu-3)#tunnel destination 8::9 Dell(conf-if-tu-3)#tunnel mode ipv6 Dell(conf-if-tu-3)#ip address 3.1.1.1/24 Dell(conf-if-tu-3)#ipv6 address 3::1/64 Dell(conf-if-tu-3)#no shutdown Dell(conf-if-tu-3)#show config ! interface Tunnel 3 ip address 3.1.1.1/24 ipv6 address 3::1/64 tunnel destination 8::9 tunnel source 5::5 tunnel mode ipv6 no shutdown Configuring Tunnel Keepalive Settings You can configure a tunnel keepalive target, keepalive interval, and attempts.
Dell(conf-if-tu-1)#ipv6 unnumbered tengigabitethernet 1/1 Dell(conf-if-tu-1)#tunnel source 40.1.1.1 Dell(conf-if-tu-1)#tunnel mode ipip decapsulate-any Dell(conf-if-tu-1)#no shutdown Dell(conf-if-tu-1)#show config ! interface Tunnel 1 ip unnumbered TenGigabitEthernet 1/1 ipv6 unnumbered TenGigabitEthernet 1/1 tunnel source 40.1.1.
no shutdown Guidelines for Configuring Multipoint Receive-Only Tunnels • Maximum number of allowed remote end-points that can be configured for a single multipoint receive-only tunnel is eight. Maximum number of allowed remote end-points that can be configured for all multipoint receive-only tunnels depends on the hardware table size to setup termination (it is 512 entries in S4810 and S4820T platforms) and the count is tracked across all of the tunnel remote end-points configured in the system.
52 Upgrade Procedures To find the upgrade procedures, go to the Dell Networking OS Release Notes for your system type to see all the requirements needed to upgrade to the desired Dell Networking OS version. To upgrade your system type, follow the procedures in the Dell Networking OS Release Notes. Get Help with Upgrades Direct any questions or concerns about the Dell Networking OS upgrade procedures to the Dell Technical Support Center. You can reach Technical Support: • On the web: http://www.dell.
53 Virtual LANs (VLANs) Virtual LANs (VLANs) are supported on Dell Networking OS. VLANs are a logical broadcast domain or logical grouping of interfaces in a local area network (LAN) in which all data received is kept locally and broadcast to all members of the group. When in Layer 2 mode, VLANs move traffic at wire speed and can span multiple devices. The Dell Networking Operating System (OS) supports up to 4093 port-based VLANs and one default VLAN, as specified in IEEE 802.1Q.
NOTE: You cannot assign an IP address to the Default VLAN. To assign an IP address to a VLAN that is currently the Default VLAN, create another VLAN and assign it to be the Default VLAN. For more information about assigning IP addresses, refer to Assigning an IP Address to a VLAN. • Untagged interfaces must be part of a VLAN. To remove an untagged interface from the Default VLAN, create another VLAN and place the interface into that VLAN.
• The VLAN protocol identifier identifies the frame as tagged according to the IEEE 802.1Q specifications (2 bytes). • Tag control information (TCI) includes the VLAN ID (2 bytes total). The VLAN ID can have 4,096 values, but two are reserved. NOTE: The insertion of the tag header into the Ethernet frame increases the size of the frame to more than the 1,518 bytes as specified in the IEEE 802.3 standard. Some devices that are not compliant with IEEE 802.3 may not support the larger frame size.
Assigning Interfaces to a VLAN You can only assign interfaces in Layer 2 mode to a VLAN using the tagged and untagged commands. To place an interface in Layer 2 mode, use the switchport command. You can further designate these Layer 2 interfaces as tagged or untagged. For more information, refer to the Interfaces chapter and Configuring Layer 2 (Data Link) Mode.
NUM Status Q * 1 Inactive 2 Active T T 3 Active T T 4 Active T Ports Po1(So 0/0-1) Te 1/1 Po1(So 0/0-1) Te 1/2 Po1(So 0/0-1) When you remove a tagged interface from a VLAN (using the no tagged interface command), it remains tagged only if it is a tagged interface in another VLAN. If the tagged interface is removed from the only VLAN to which it belongs, the interface is placed in the Default VLAN as an untagged interface.
* 1 2 3 4 Inactive Active T T Active T T Active U Po1(So 0/0-1) Te 1/3 Po1(So 0/0-1) Te 1/1 Te 1/2 The only way to remove an interface from the Default VLAN is to place the interface in Default mode by using the no switchport command in INTERFACE mode. Assigning an IP Address to a VLAN VLANs are a Layer 2 feature. For two physical interfaces on different VLANs to communicate, you must assign an IP address to the VLANs to route traffic between the two interfaces.
3. Configure the interface for Switchport mode. INTERFACE mode switchport 4. Add the interface to a tagged or untagged VLAN. VLAN INTERFACE mode [tagged | untagged] Enabling Null VLAN as the Default VLAN In a Carrier Ethernet for Metro Service environment, service providers who perform frequent reconfigurations for customers with changing requirements occasionally enable multiple interfaces, each connected to a different customer, before the interfaces are fully configured.
54 VLT Proxy Gateway The Virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, refer to Dell Networking OS Command Line Reference Guide.
Guidelines for Enabling the VLT Proxy Gateway Keep the following points in mind when you enable a VLT proxy gateway: • Proxy gateway is supported only for VLT; for example, across a VLT domain. • You must enable the VLT peer-routing command for the VLT proxy gateway to function. • Asymmetric virtual local area network (VLAN) configuration, such as the same VLAN configured with Layer 2 (L2) mode on one VLT domain and L3 mode on another VLT domain is not supported.
• Dell Networking recommends the vlt-peer-mac transmit command only for square VLTs without diagonal links. • The virtual router redundancy (VRRP) protocol and IPv6 routing is not supported. • Private VLANs (PVLANs) are not supported. • When a Virtual Machine (VM) moves from one VLT domain to the another VLT domain, the VM host sends the gratuitous ARP (GARP) , which in-turn triggers a mac movement from the previous VLT domain to the newer VLT domain.
• You must have at least one link connection to each unit of the VLT domain. Following are the prerequisites for Proxy Gateway LLDP configuration: • You must globally enable LLDP. • You cannot have interface–level LLDP disable commands on the interfaces configured for proxy gateway and you must enable both transmission and reception. • You must connect both units of the remote VLT domain by the port channel member.
• The above figure shows a sample VLT Proxy gateway scenario. There are no diagonal links in the square VLT connection between the C and D in VLT domain 1 and C1 and D1 in the VLT domain 2. This causes sub-optimal routing with the VLT Proxy Gateway LLDP method. For VLT Proxy Gateway to work in this scenario you must configure the VLT-peer-mac transmit command under VLT Domain Proxy Gateway LLDP mode, in both C and D (VLT domain 1) and C1 and D1 (VLT domain 2).
Sample Dynamic Proxy Configuration on C switch or C1 switch Switch_C#conf Switch_C(conf)#vlt domain 1 Switch_C(conf-vlt-domain1)#proxy-gateway lldp Switch_C(conf-vlt-domain1-pxy-gw-lldp)#peer-domain-link port-channel 1....
55 Virtual Link Trunking (VLT) Overview VLT allows physical links between two chassis to appear as a single virtual link to the network core or other switches such as Edge, Access, or top-of-rack (ToR). VLT reduces the role of spanning tree protocols (STPs) by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology. (To prevent the initial loop that may occur prior to VLT being established, use a spanning tree protocol.
Figure 121. VLT on Switches VLT on Core Switches Uplinks from servers to the access layer and from access layer to the aggregation layer are bundled in LAG groups with end-to-end Layer 2 multipathing. This set up requires “horizontal” stacking at the access layer and VLT at the aggregation layer such that all the uplinks from servers to access and access to aggregation are in Active-Active Load Sharing mode.
Figure 122. Enhanced VLT VLT Terminology The following are key VLT terms. • Virtual link trunk (VLT) — The combined port channel between an attached device and the VLT peer switches. • VLT backup link — The backup link monitors the vitality of VLT peer switches. The backup link sends configurable, periodic keep alive messages between the VLT peer switches. • VLT interconnect (VLTi) — The link used to synchronize states between the VLT peer switches.
• If you include PVST on the system, configure it before VLT. Refer to PVST Configuration. • Dell Networking strongly recommends that the VLTi (VLT interconnect) be a static LAG and that you disable LACP on the VLTi. • Ensure that the spanning tree root bridge is at the Aggregation layer. If you enable RSTP on the VLT device, refer to RSTP and VLT for guidelines to avoid traffic loss.
Configuration Notes When you configure VLT, the following conditions apply. • VLT domain – A VLT domain supports two chassis members, which appear as a single logical device to network access devices connected to VLT ports through a port channel. – A VLT domain consists of the two core chassis, the interconnect trunk, backup link, and the LAG members connected to attached devices. – Each VLT domain has a unique MAC address that you create or VLT creates automatically.
NOTE: If you configure the VLT system MAC address or VLT unit-id on only one of the VLT peer switches, the link between the VLT peer switches is not established. Each VLT peer switch must be correctly configured to establish the link between the peers. – If the link between the VLT peer switches is established, changing the VLT system MAC address or the VLT unit-id causes the link between the VLT peer switches to become disabled.
– For detailed information about how to use VRRP in a VLT domain, refer to the following VLT and VRRP interoperability section. – For information about configuring IGMP Snooping in a VLT domain, refer to VLT and IGMP Snooping. – All system management protocols are supported on VLT ports, including SNMP, RMON, AAA, ACL, DNS, FTP, SSH, Syslog, NTP, RADIUS, SCP, TACACS+, Telnet, and LLDP. – Enable Layer 3 VLAN connectivity VLT peers by configuring a VLAN network interface for the same VLAN on both switches.
If the VLTi link fails, the status of the remote VLT Primary Peer is checked using the backup link. If the remote VLT Primary Peer is available, the Secondary Peer disables all VLT ports to prevent loops. If all ports in the VLTi link fail or if the communication between VLTi links fails, VLT checks the backup link to determine the cause of the failure.
• Non-VLT Sync — Entries learned on non-VLT interfaces are synced on both VLT peers. • Tunneling — Control information is associated with tunnel traffic so that the appropriate VLT peer can mirror the ingress port as the VLT interface rather than pointing to the VLT peer’s VLTi link. • Statistics and Counters — Statistical and counter information displays IPv6 information when applicable. • Heartbeat — You can configure an IPv4 or IPv6 address as a backup link destination.
Figure 123. PIM-Sparse Mode Support on VLT On each VLAN where the VLT peer nodes act as the first hop or last hop routers, one of the VLT peer nodes is elected as the PIM designated router. If you configured IGMP snooping along with PIM on the VLT VLANs, you must configure VLTi as the static multicast router port on both VLT peer switches. This ensures that for first hop routers, the packets from the source are redirected to the designated router (DR) if they are incorrectly hashed.
To verify the PIM neighbors on the VLT VLAN and on the multicast port, use the show ip pim neighbor, show ip igmp snooping mrouter, and show running config commands. You can configure virtual link trunking (VLT) peer nodes as rendezvous points (RPs) in a Protocol Independent Multicast (PIM) domain. If the VLT node elected as the designated router fails and you enable VLT Multicast Routing, multicast routes are synced to the other peer for traffic forwarding to ensure minimal traffic loss.
peer-routing 3. Configure the peer-routing timeout. VLT DOMAIN mode peer-routing—timeout value value: Specify a value (in seconds) from 1 to 65535. The default value is infinity (without configuring the timeout). VLT Multicast Routing VLT Multicast Routing provides resiliency to multicast routed traffic during the multicast routing protocol convergence period after a VLT link or VLT peer fails using the least intrusive method (PIM) and does not alter current protocol behavior.
5. Configure a PIM-enabled external neighboring router as a rendezvous point (RP). For more information, refer to Configuring a Static Rendezvous Point. 6. Configure the VLT VLAN routing metrics to prefer VLT VLAN interfaces over non-VLT VLAN interfaces. For more information, refer to Classify Traffic. 7. Configure symmetrical Layer 2 and Layer 3 configurations on both VLT peers for any spanned VLAN.
In the case of a primary VLT switch failure, the secondary switch starts sending BPDUs with its own bridge ID and inherits all the port states from the last synchronization with the primary switch. An access device never detects the change in primary/secondary roles and does not see it as a topology change. The following examples show the RSTP configuration that you must perform on each peer switch to prevent forwarding loops.
channel-member interface interface: specify one of the following interface types: 4. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Ensure that the port channel is active. INTERFACE PORT-CHANNEL mode no shutdown 5. Repeat Steps 1 to 4 on the VLT peer switch to configure the VLT interconnect.
CONFIGURATION mode interface managementethernet slot/ port Enter the slot (0-1) and the port (0). 2. Configure an IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) and mask (/x) on the interface. MANAGEMENT INTERFACE mode {ip address ipv4-address/ mask | ipv6 address ipv6-address/ mask} This is the IP address to be configured on the VLT peer with the back-up destination command. 3. Ensure that the interface is active. MANAGEMENT INTERFACE mode no shutdown 4.
The priority values are from 1 to 65535. The default is 32768. 3. (Optional) When you create a VLT domain on a switch, Dell Networking OS automatically creates a VLT-system MAC address used for internal system operations. VLT DOMAIN CONFIGURATION mode system-mac mac-address mac-address To explicitly configure the default MAC address for the domain by entering a new MAC address, use the system-mac command. The format is aaaa.bbbb.cccc. Also, reconfigure the same MAC address on the VLT peer switch.
no shutdown 6. Associate the port channel to the corresponding port channel in the VLT peer for the VLT connection to an attached device. INTERFACE PORT-CHANNEL mode vlt-peer-lag port-channel id-number The valid port-channel ID numbers are from 1 to 128. 7. Repeat Steps 1 to 6 on the VLT peer switch to configure the same port channel as part of the VLT domain. 8. On an attached switch or server: To connect to the VLT domain and add port channels to it, configure a port channel.
3. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Enter VLT-domain configuration mode for a specified VLT domain. CONFIGURATION mode vlt domain domain-id The range of domain IDs is from 1 to 1000. 4. Enter the port-channel number that acts as the interconnect trunk.
9. Place the interface in Layer 2 mode. INTERFACE PORT-CHANNEL mode switchport 10. Associate the port channel to the corresponding port channel in the VLT peer for the VLT connection to an attached device. INTERFACE PORT-CHANNEL mode vlt-peer-lag port-channel id-number Valid port-channel ID numbers are from 1 to 128. 11. Ensure that the port channel is active. INTERFACE PORT-CHANNEL mode no shutdown 12. Add links to the eVLT port. Configure a range of interfaces to bulk configure.
channel-member 5. Configure the backup link between the VLT peer units (shown in the following example). 6. Configure the peer 2 management ip/ interface ip for which connectivity is present in VLT peer 1. EXEC Privilege mode show running-config vlt 7. Configure the peer 1 management ip/ interface ip for which connectivity is present in VLT peer 1. EXEC mode or EXEC Privilege mode show interfaces interface 8.
Configure the backup link between the VLT peer units. 1. Configure the peer 2 management ip/ interface ip for which connectivity is present in VLT peer 1. 2. Configure the peer 1 management ip/ interface ip for which connectivity is present in VLT peer 2. Dell-2#show running-config vlt ! vlt domain 5 peer-link port-channel 1 back-up destination 10.11.206.58 Dell-2# show interfaces managementethernet 0/0 Internet address is 10.11.206.
port-channel-protocol LACP port-channel 100 mode active no shutdown s60-1#show running-config interface tengigabitethernet 1/30 ! interface TenGigabitEthernet 1/30 no ip address ! port-channel-protocol LACP port-channel 100 mode active no shutdown s60-1#show running-config interface port-channel 100 ! interface Port-channel 100 no ip address switchport no shutdown s60-1#show interfaces port-channel 100 brief Codes: L - LACP Port-channel LAG 100 L Mode L2 Status up Uptime 03:33:48 Ports Te 1/8 (Up) Te 1
PVST+ Configuration PVST+ is supported in a VLT domain. Before you configure VLT on peer switches, configure PVST+ in the network. PVST+ is required for initial loop prevention during the VLT startup phase. You may also use PVST+ for loop prevention in the network outside of the VLT port channel. Run PVST+ on both VLT peer switches. PVST+ instance will be created for every VLAN configured in the system.
eVLT Configuration Example The following example demonstrates the steps to configure enhanced VLT (eVLT) in a network. In this example, you are configuring two domains. Domain 1 consists of Peer 1 and Peer 2; Domain 2 consists of Peer 3 and Peer 4, as shown in the following example. In Domain 1, configure Peer 1 fist, then configure Peer 2. When that is complete, perform the same steps for the peer nodes in Domain 2. The interface used in this example is TenGigabitEthernet. Figure 124.
Next, configure the VLT domain and VLTi on Peer 2. Domain_1_Peer2#configure Domain_1_Peer2(conf)#interface port-channel 1 Domain_1_Peer2(conf-if-po-1)# channel-member TenGigabitEthernet 1/8-9 Domain_1_Peer2(conf) #vlt domain Domain_1_Peer2(conf-vlt-domain)# Domain_1_Peer2(conf-vlt-domain)# Domain_1_Peer2(conf-vlt-domain)# Domain_1_Peer2(conf-vlt-domain)# 1000 peer-link port-channel 1 back-up destination 10.16.130.12 system-mac mac-address 00:0a:00:0a:00:0a unit-id 1 Configure eVLT on Peer 2.
Domain_2_Peer4(conf-vlt-domain)# system-mac mac-address 00:0b:00:0b:00:0b Domain_2_Peer4(conf-vlt-domain)# unit-id 1 Configure eVLT on Peer 4. Domain_2_Peer4(conf)#interface port-channel 100 Domain_2_Peer4(conf-if-po-100)# switchport Domain_2_Peer4(conf-if-po-100)# vlt-peer-lag port-channel 100 Domain_2_Peer4(conf-if-po-100)# no shutdown Add links to the eVLT port-channel on Peer 4.
Verifying a VLT Configuration To monitor the operation or verify the configuration of a VLT domain, use any of the following show commands on the primary and secondary VLT switches. • Display information on backup link operation. EXEC mode • show vlt backup-link Display general status information about VLT domains currently configured on the switch.
HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 3 34998 1026 1025 Dell_VLTpeer2# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.20 Up 1 3 34998 1030 1014 The following example shows the show vlt brief command.
VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 The following example shows the show running-config vlt command. Dell_VLTpeer1# show running-config vlt ! vlt domain 30 peer-link port-channel 60 back-up destination 10.11.200.18 Dell_VLTpeer2# show running-config vlt ! vlt domain 30 peer-link port-channel 60 back-up destination 10.11.200.
Executing IEEE compatible Spanning Tree Protocol Root ID Priority 0, Address 0001.e88a.dff8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 0, Address 0001.e88a.dff8 We are the root Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------- -------- ---- ------- -------- - ------- ------------Po 1 128.2 128 200000 DIS 0 0 0001.e88a.dff8 128.2 Po 3 128.4 128 200000 DIS 0 0 0001.e88a.dff8 128.4 Po 4 128.
Verify that the port channels used in the VLT domain are assigned to the same VLAN.
Verifying a Port-Channel Connection to a VLT Domain (From an Attached Access Switch) On an access device, verify the port-channel connection to a VLT domain. Dell_TORswitch(conf)# show running-config interface port-channel 11 ! interface Port-channel 11 no ip address switchport channel-member fortyGigE 1/48,52 no shutdown Troubleshooting VLT To help troubleshoot different VLT issues that may occur, use the following information.
Description Behavior at Peer Up Behavior During Run Time Action to Take Unit ID mismatch The VLT peer does not boot up. The VLTi is forced to a down state. The VLT peer does not boot up. The VLTi is forced to a down state. A syslog error message is generated. A syslog error message is generated. Verify the unit ID is correct on both VLT peers. Unit ID numbers must be sequential on peer units; for example, if Peer 1 is unit ID “0”, Peer 2 unit ID must be “1’.
You can associate either a VLT VLAN or a VLT LAG to a PVLAN. First configure the VLT interconnect (VLTi) or a VLT LAG by using the peer-link port-channel id-number command or the VLT VLAN by using the peer-link port-channel idnumber peer-down-vlan vlan interface number command and the switchport command.
Whenever a change occurs in the VLAN mode of one of the peers, this modification is synchronized with the other peers. Depending on the validation mechanism that is initiated for MAC synchronization of VLT peers, MAC addresses learned on a particular VLAN are either synchronized with the other peers, or MAC addresses synchronized from the other peers on the same VLAN are deleted. This method of processing occurs when the PVLAN mode of VLT LAGs is modified.
Table 80.
VLT LAG Mode PVLAN Mode of VLT VLAN Peer1 Peer2 Peer1 Peer2 Trunk Access Primary/Normal Secondary ICL VLAN Membership Mac Synchronization No No Configuring a VLT VLAN or LAG in a PVLAN You can configure the VLT peers or nodes in a private VLAN (PVLAN). Because the VLT LAG interfaces are terminated on two different nodes, PVLAN configuration of VLT VLANs and VLT LAGs are symmetrical and identical on both the VLT peers. PVLANs provide Layer 2 isolation between ports within the same VLAN.
The range is from 1 to 128. 8. (Optional) To configure a VLT LAG, enter the VLAN ID number of the VLAN where the VLT forwards packets received on the VLTi from an adjacent peer that is down. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number peer-down-vlan vlan interface number The range is from 1 to 4094. Associating the VLT LAG or VLT VLAN in a PVLAN 1. Access INTERFACE mode for the port that you want to assign to a PVLAN. CONFIGURATION mode interface interface 2. Enable the port.
• Amended by specifying the new secondary VLAN to be added to the list. Proxy ARP Capability on VLT Peer Nodes The proxy ARP functionality is supported on VLT peer nodes. A proxy ARP-enabled device answers the ARP requests that are destined for another host or router. The local host forwards the traffic to the proxy ARP-enabled device, which in turn transmits the packets to the destination. By default, proxy ARP is enabled. To disable proxy ARP, use the no proxy-arp command in the interface mode.
When a VLT node detects peer up, it will not perform proxy ARP for the peer IP addresses. IP address synchronization occurs again between the VLT peers. Proxy ARP is enabled only if peer routing is enabled on both the VLT peers. If you disable peer routing by using the no peerroutingcommand in VLT DOMAIN node, a notification is sent to the VLT peer to disable the proxy ARP.
Configuring VLAN-Stack over VLT To configure VLAN-stack over VLT, follow these steps. 1. Configure the VLT LAG as VLAN-stack access or trunk mode on both the peers. INTERFACE PORT-CHANNEL mode vlan-stack {access | trunk} 2. Configure VLAN as VLAN-stack compatible on both the peers. INTERFACE VLAN mode vlan-stack compatible 3. Add the VLT LAG as a member to the VLAN-stack on both the peers. INTERFACE VLAN mode member port-channel port—channel ID 4. Verify the VLAN-stack configurations.
no shutdown Dell# Dell(conf)#interface port-channel 20 Dell(conf-if-po-20)#switchport Dell(conf-if-po-20)#vlt-peer-lag port-channel 20 Dell(conf-if-po-20)#vlan-stack trunk Dell(conf-if-po-20)#no shutdown Dell#show running-config interface port-channel 20 ! interface Port-channel 20 no ip address switchport vlan-stack trunk vlt-peer-lag port-channel 20 no shutdown Dell# Configure VLAN as VLAN-Stack VLAN and add the VLT LAG as Members to the VLAN Dell(conf)#interface vlan 50 Dell(conf-if-vl-50)#vlan-stack com
back-up destination 10.16.151.
NUM 50 Status Active Description Dell# 880 Virtual Link Trunking (VLT) Q M M V Ports Po10(Te 1/8) Po20(Te 1/20) Po1(Te 1/30-32)
56 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell Networking OS. Overview The switch acts as the VXLAN gateway and performs the VXLAN Tunnel End Point (VTEP) functionality. VXLAN is a technology where in the data traffic from the virtualized servers is transparently transported over an existing legacy network. Components of VXLAN network VXLAN provides a mechanism to extend an L2 network over an L3 network.
• Service Node (SN) • Legacy TOR Network Virtualization Platform (NVP) Controller NVP Controller is the network controller for managing cloud components. The OVSDB protocol is the protocol used for communication between VTEPs and the controller. In the current release, the qualified controller for the VXLAN Gateway function is NSX-from VMWare. The top-level functions of NVP are: • Provide a GUI for creating service gateways. • Manage the VTEPs.
• The VTEP acts according to the TOR schema defined by VMWare. The solution is very specific to VMWare-based orchestration platforms and does not work with other orchestration platforms. VXLAN Frame Format VXLAN provides a mechanism to extend an L2 network over an L3 network. In short, VXLAN is an L2 overlay scheme over an L3 network and this overlay is termed as a VXLAN segment. VMs within the same VXLAN segment communicate with each other through a 24–bit ID called VXLAN Network Identifier (VNI).
VXLAN Header : Frame Check Sequence (FCS): • VXLAN Port : IANA-assigned VXLAN Port (4789). • UDP Checksum: The UDP checksum field is transmitted as zero. When a packet is received with a UDP checksum of zero, it is accepted for decapsulation. • VXLAN Flags : Reserved bits set to zero except bit 3, the first bit, which is set to 1 for a valid VNI • VNI: The 24-bit field that is the VXLAN Network Identifier • Reserved: A set of fields, 24 bits and 8 bits, that are reserved and set to zero .
2. Create Service Node To create service node, the required fields are the IP address and SSL certificate of the server. The Service node is responsible for broadcast/unknown unicast/multicast traffic replication. The following is the snapshot of the user interface for the creation of service node: 3. Create VXLAN Gateway To create a VXLAN L2 Gateway, the IP address of the Gateway is mandatory. The following is the snapshot of the user interface in creating a VXLAN Gateway 4.
5. Create Logical Switch Port A logical switch port provides a logical connection point for a VM interface (VIF) and a L2 gateway connection to an external network. It binds the virtual access ports in the GW to logical network (VXLAN) and VLAN. NOTE: For more details about NVP controller configuration, refer to the NVP user guide from VMWare . Configuring VxLAN Gateway To configure the VxLAN gateway on the switch, follow these steps: 1. Connecting to NVP controller 2.
VxLAN INSTANCE mode gateway-ip IP address 5. max-back off (Optional) VxLAN INSTANCE mode max_backoff time The range is from 1000-180000. The default value is 30000 milliseconds. 6. fail-mode (Optional) VxLAN INSTANCE mode fail-mode secure If the local VTEP loses connectivity with the controller, it will delete all its database and hardware flows/resources. 7.
Port : Fo 0/124 Vlan : 100 Rx Packets : 13 Rx Bytes : 1317 Tx Packets : 13 Tx Bytes : 1321 The following example shows the show vxlan vxlan-instance physical-locator command. Dell#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) The following example shows the show vxlan vxlan-instance unicast-mac-local command.
Total LN count : 1 Name bffc3be0-13e6-4745-9f6b-0bcbc5877f01 VNID 4656 Dell#$n-instance 1 logical-network n 2a8d5d19-8845-4365-ad04-243f0b6df252 Name : 2a8d5d19-8845-4365-ad04-243f0b6df252 Description : Tunnel Key : 2 VFI : 28674 Unknown Multicast MAC Tunnels: 192.168.122.133 : vxlan_over_ipv4 (up) Port Vlan Bindings: Te 0/80: VLAN: 0 (0x80000001), Fo 0/124: VLAN: 0 (0x80000004), The following example shows the show vxlan vxlan-instance statistics interface command.
57 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows a physical router to partition itself into multiple Virtual Routers (VRs). The control and data plane are isolated in each VR so that traffic does NOT flow across VRs.Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist within the same router at the same time. VRF Overview VRF improves functionality by allowing network paths to be segmented without using multiple devices.
Figure 125. VRF Network Example VRF Configuration Notes Although there is no restriction on the number of VLANs that can be assigned to a VRF instance, the total number of routes supported in VRF is limited by the size of the IPv4 CAM. VRF is implemented in a network device by using Forwarding Information Bases (FIBs). A network device may have the ability to configure different virtual routers, where entries in the FIB that belong to one VRF cannot be accessed by another VRF on the same device.
Table 81. Feature/Capability Support Status for Default VRF Support Status for Non-default VRF Configuration rollback for commands introduced or modified Yes No LLDP protocol on the port Yes No 802.
Feature/Capability Support Status for Default VRF Support Status for Non-default VRF sFlow Yes No VRRP on physical and logical interfaces Yes Yes VRRPV3 Yes Yes Secondary IP Addresses Yes No Following IPv6 capabilities No Basic Yes No OSPFv3 Yes Yes IS-IS Yes Yes BGP Yes Yes ACL Yes No Multicast Yes No NDP Yes Yes RAD Yes Yes Ingress/Egress Storm-Control (perinterface/global) Yes No DHCP DHCP requests are not forwarded across VRF instances.
Creating a Non-Default VRF Instance VRF is enabled by default on the switch and supports up to 64 VRF instances: 1 to 63 and the default VRF (0). Task Command Syntax Command Mode Create a non-default VRF instance by specifying a name and VRF ID number, and enter VRF configuration mode.
Task Command Syntax Command Mode instances (including the default VRF 0), do not enter a value for vrf-name. Assigning an OSPF Process to a VRF Instance OSPF routes are supported on all VRF instances. Refer toOpen Shortest Path First (OSPFv2) for complete OSPF configuration information. Assign an OSPF process to a VRF instance . Return to CONFIGURATION mode to enable the OSPF process.
Task Command Syntax Command Mode Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 43, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:0a Virtual IP address: 10.1.1.100 Authentication: (none) Configuring Management VRF You can assign a management interface to a management VRF. Task Command Syntax Command Mode Create a management VRF. ip vrf management CONFIGURATION Assign a management port to a management VRF.
Task Command Syntax Command Mode NOTE: You can also have the management route to point to a front-end port in case of the management VRF. For example: management route 2::/64 te 0/0. To configure a static entry in the IPv6 neighbor discovery, perform the following steps: Task Command Syntax Command Mode Configure a static neighbor.
Figure 127. Setup VRF Interfaces The following example relates to the configuration shown in Figure1 and Figure 2. Router 1 ip vrf blue 1 ! ip vrf orange 2 ! ip vrf green 3 ! interface TenGigabitEthernet no ip address switchport no shutdown ! interface TenGigabitEthernet ip vrf forwarding blue ip address 10.0.0.1/24 no shutdown ! interface TenGigabitEthernet ip vrf forwarding orange ip address 20.0.0.
ip vrf forwarding green ip address 30.0.0.1/24 no shutdown ! interface Vlan 128 ip vrf forwarding blue ip address 1.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 192 ip vrf forwarding orange ip address 2.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.1/24 tagged TenGigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.1 network 1.0.0.0/24 area 0 network 10.0.0.
ip vrf forwarding blue ip address 1.0.0.2/24 tagged TenGigabitEthernet 3/1 no shutdown interface Vlan 192 ip vrf forwarding orange ip address 2.0.0.2/24 tagged TenGigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.2/24 tagged TenGigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.2 network 11.0.0.0/24 area 0 network 1.0.0.0/24 area 0 passive-interface TenGigabitEthernet 2/1 ! router ospf 2 vrf orange router-id 2.0.0.2 network 21.0.0.
E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set C C O Destination ----------1.0.0.0/24 10.0.0.0/24 11.0.0.0/24 Gateway ------Direct, Vl 128 Direct, Te 1/1 via 1.0.0.
Dell#show ip ospf 1 neighbor Neighbor ID Pri 1.0.0.1 1 FULL/BDR ! Dell#sh ip ospf 2 neighbor Neighbor ID Pri 2.0.0.1 1 FULL/BDR ! Dell#show ip route vrf blue State Dead Time 00:00:36 Address 1.0.0.1 Interface Vl 128 Area State Dead Time 00:00:33 Address 2.0.0.
Route Leaking VRFs Static routes can be used to redistribute routes between non-default to default/non-default VRF and vice-versa. You can configure route leaking between two VRFs using the following command: ip route vrf x.x.x.x s.s.s.s nh.nh.nh.nh vrf default. This command indicates that packets that are destined to x.x.x.x/s.s.s.s are reachable through nh.nh.nh.nh in the default VRF table. Meaning, the routes to x.x.x.x/s.s.s.
purpose, routes corresponding VRF-Shared routes are leaked to only VRF-Red and VRF-Blue. And for reply, routes corresponding to VRF-Red and VRF-Blue are leaked to VRF-Shared. For leaking the routes from VRF-Shared to VRF-Red and VRF-Blue, you can configure route-export tag on VRF-shared (source VRF, who is exporting the routes); the same route-export tag value should be configured on VRF-Red and VRF-blue as route-import tag (target VRF, that is importing the routes).
Dell# show ip route vrf VRF-Green O 33.3.3.3/32 via 133.3.3.3 00:00:11 C 133.3.3.0/24 110/0 Direct, Te 1/13 0/0 22:39:61 Dell# show ip route vrf VRF-Shared O 44.4.4.4/32 via 144.4.4.4 110/0 00:00:11 C 144.4.4.0/24 Direct, Te 1/4 0/0 00:32:36 Show routing tables of VRFs( after route-export and route-import tags are configured). Dell# show ip route vrf VRF-Red O C O C 11.1.1.1/32 111.1.1.0/24 44.4.4.4/32 144.4.4.0/24 via 111.1.1.1 110/0 00:00:10 Direct, Te 1/11 0/0 22:39:59 via VRF-shared:144.4.4.
Configuring Route Leaking with Filtering When you initalize route leaking from one VRF to another, all the routes are exposed to the target VRF. If the size of the source VRF's RTM is considerablly large, an import operation results in the duplication of the target VRF's RTM with the source RTM entries. To mitigate this issue, you can use route-maps to filter the routes that are exported and imported into the route targets based on certain matching criteria.
The show run output for the above configuration is as follows: ip vrf vrf-Red ip route-export 1:1 export_ospfbgp_protocol ip route-import 2:2 ! this action exports only the OSPF and BGP routes to other VRFs ! ip vrf vrf-Blue ip route-export 2:2 ip route-import 1:1 import_ospf_protocol !this action accepts only OSPF routes from VRF-red even though both OSPF as well as BGP routes are shared The show VRF commands displays the following output: Dell# show ip route vrf VRF-Blue C 122.2.2.
58 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported on Dell Networking OS. VRRP Overview VRRP is designed to eliminate a single point of failure in a statically routed network. VRRP specifies a MASTER router that owns the next hop IP and MAC address for end stations on a local area network (LAN). The MASTER router is chosen from the virtual routers by an election process and forwards packets sent to the next hop IP address.
Figure 128. Basic VRRP Configuration VRRP Benefits With VRRP configured on a network, end-station connectivity to the network is not subject to a single point-of-failure. End-station connections to the network are redundant and are not dependent on internal gateway protocol (IGP) protocols to converge or update routing tables. VRRP Implementation Within a single VRRP group, up to 12 virtual IP addresses are supported.
Configuration Task List The following list specifies the configuration tasks for VRRP.
• VRRPv3 as defined in RFC 5798, Virtual Router Redundancy Protocol (VRRP) Version 3 for IPv4 and IPv6 You can also migrate a IPv4 group from VRRPv2 to VRRP3. To configure the VRRP version for IPv4, use the version command in INTERFACE mode. Example: Configuring VRRP to Use Version 3 The following example configures the IPv4 VRRP 100 group to use VRRP protocol version 3.
• • – For example, an interface (on which you enable VRRP) contains a primary IP address of 50.1.1.1/24 and a secondary IP address of 60.1.1.1/24. The VRRP group (VRID 1) must contain virtual addresses belonging to either subnet 50.1.1.0/24 or subnet 60.1.1.0/24, but not from both subnets (though Dell Networking OS allows the same). If the virtual IP address and the interface’s primary/secondary IP address are the same, the priority on that VRRP group MUST be set to 255.
TenGigabitEthernet 1/2, VRID: 111, Net: 10.10.2.1 State: Master, Priority: 100, Master: 10.10.2.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 27, Gratuitous ARP sent: 2 Virtual MAC address: 00:00:5e:00:01:6f Virtual IP address: 10.10.2.2 10.10.2.3 Authentication: When the VRRP process completes its initialization, the State field contains either Master or Backup.
NOTE: You must configure all virtual routers in the VRRP group the same: you must enable authentication with the same password or authentication is disabled. To configure simple authentication, use the following command. • Configure a simple text password. INTERFACE-VRID mode authentication-type simple [encryption-type] password Parameters: – encryption-type: 0 indicates unencrypted; 7 indicates encrypted. – password: plain text.
vrrp-group 111 authentication-type simple 7 387a7f2df5969da4 no preempt priority 255 virtual-address 10.10.10.1 virtual-address 10.10.10.2 virtual-address 10.10.10.3 virtual-address 10.10.10.10 Changing the Advertisement Interval By default, the MASTER router transmits a VRRP advertisement to all members of the VRRP group every one second, indicating it is operational and is the MASTER router.
no preempt priority 255 virtual-address virtual-address virtual-address virtual-address 10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10 Track an Interface or Object You can set Dell Networking OS to monitor the state of any interface according to the virtual group. Each VRRP group can track up to 12 interfaces and up to 20 additional objects, which may affect the priority of the VRRP group. If the tracked interface goes down, the VRRP group’s priority decreases by a default value of 10 (also known as cost).
show vrrp • (Optional) Display the configuration of tracked objects in VRRP groups on a specified interface. EXEC mode or EXEC Privilege mode show running-config interface interface Examples of Configuring and Viewing the track Command The following example shows how to configure tracking using the track command. Dell(conf-if-te-1/1)#vrrp-group 111 Dell(conf-if-te-1/1-vrid-111)#track Tengigabitethernet 1/2 The following example shows how to verify tracking using the show conf command.
The following example shows verifying the VRRP configuration on an interface. Dell#show running-config interface tengigabitethernet 1/8 interface TenGigabitEthernet 1/8 no ip address ipv6 address 2007::30/64 vrrp-ipv6-group 1 track 2 priority-cost 20 track 3 priority-cost 30 virtual-address 2007::1 virtual-address fe80::1 no shutdown Setting VRRP Initialization Delay When configured, VRRP is enabled immediately upon system reload or boot.
Sample Configurations Before you set up VRRP, review the following sample configurations. VRRP for an IPv4 Configuration The following configuration shows how to enable IPv4 VRRP. This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes.
R2(conf-if-te-2/31-vrid-99)#priority 200 R2(conf-if-te-2/31-vrid-99)#virtual 10.1.1.3 R2(conf-if-te-2/31-vrid-99)#no shut R2(conf-if-te-2/31)#show conf ! interface TenGigabitEthernet 2/31 ip address 10.1.1.1/24 ! vrrp-group 99 priority 200 virtual-address 10.1.1.3 no shutdown R2(conf-if-te-2/31)#end R2#show vrrp -----------------TenGigabitEthernet 2/31, VRID: 99, Net: 10.1.1.1 State: Master, Priority: 200, Master: 10.1.1.
Figure 130. VRRP for an IPv6 Configuration NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be MASTER even if one of two routers has a higher IP or IPv6 address. The following example shows configuring VRRP for IPv6 Router 2 and Router 3. Configure a virtual link local (fe80) address for each VRRPv3 group created for an interface.
R2(conf-if-te-1/1-vrid-10)#virtual-address fe80::10 R2(conf-if-te-1/1-vrid-10)#virtual-address 1::10 R2(conf-if-te-1/1-vrid-10)#no shutdown R2(conf-if-te-1/1)#show config interface TenGigabitEthernet 1/1 ipv6 address 1::1/64 vrrp-group 10 priority 100 virtual-address fe80::10 virtual-address 1::10 no shutdown R2(conf-if-te-1/1)#end R2#show vrrp -----------------TenGigabitEthernet 1/1, IPv6 VRID: 10, Version: 3, Net:fe80::201:e8ff:fe6a:c59f VRF: 0 default-vrf State: Master, Priority: 100, Master: fe80::201:e
VRRP in a VRF: Non-VLAN Scenario The following example shows how to enable VRRP in a non-VLAN. The following example shows a typical use case in which you create three virtualized overlay networks by configuring three VRFs in two E-Series switches. The default gateway to reach the internet in each VRF is a static route with the next hop being the virtual IP address configured in VRRP. In this scenario, a single VLAN is associated with each VRF.
S1(conf)#interface TenGigabitEthernet 1/1 S1(conf-if-te-1/1)#ip vrf forwarding VRF-1 S1(conf-if-te-1/1)#ip address 10.10.1.5/24 S1(conf-if-te-1/1)#vrrp-group 11 % Info: The VRID used by the VRRP group 11 in VRF 1 will be 177. S1(conf-if-te-1/1-vrid-101)#priority 100 S1(conf-if-te-1/1-vrid-101)#virtual-address 10.10.1.2 S1(conf-if-te-1/1)#no shutdown ! S1(conf)#interface TenGigabitEthernet 1/2 S1(conf-if-te-1/2)#ip vrf forwarding VRF-2 S1(conf-if-te-1/2)#ip address 10.10.1.
S2(conf-if-te-1/3)#ip vrf forwarding VRF-3 S2(conf-if-te-1/3)#ip address 20.1.1.6/24 S2(conf-if-te-1/3)#vrrp-group 15 % Info: The VRID used by the VRRP group 15 in VRF 3 will be 243. S2(conf-if-te-1/3-vrid-105)#priority 100 S2(conf-if-te-1/3-vrid-105)#virtual-address 20.1.1.5 S2(conf-if-te-1/3)#no shutdown VLAN Scenario In another scenario, to connect to the LAN, VRF-1, VRF-2, and VRF-3 use a single physical interface with multiple tagged VLANs (instead of separate physical interfaces).
VRF: 1 vrf1 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 278, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.100 Authentication: (none) Dell#show vrrp vrf vrf2 port-channel 1 -----------------Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 2 vrf2 State: Master, Priority: 100, Master: 10.1.1.
VRF: 1 vrf1 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 278, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.100 Authentication: (none) Vlan 400, IPv4 VRID: 10, Version: 2, Net: 20.1.1.2 VRF: 1 vrf1 State: Backup, Priority: 90, Master: 20.1.1.
Figure 132. VRRP for IPv6 Topology NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be master even if one of two routers has a higher IP or IPv6 address.
NOTE: The virtual IPv6 address you configure should be the same as the IPv6 subnet to which the interface belongs.
Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 Dell#show vrrp tengigabitethernet 2/8 TenGigabitEthernet 2/8, IPv6 VRID: 255, Version: 3, Net: fe80::201:e8ff:fe8a:e9ed VRF: 0 default State: Master, Priority: 110, Master: fe80::201:e8ff:fe8a:e9ed (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 120 Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe
59 S-Series Debugging and Diagnostics This chapter describes debugging and diagnostics for the device. Offline Diagnostics The offline diagnostics test suite is useful for isolating faults and debugging hardware. The diagnostics tests are grouped into three levels: • • • Level 0 — Level 0 diagnostics check for the presence of various components and perform essential path verifications. In addition, Level 0 diagnostics verify the identification registers of the components on the board.
3. Start diagnostics on the unit. diag stack-unit stack-unit-number When the tests are complete, the system displays the following message and automatically reboots the unit. Dell#00:09:42 : Diagnostic test results are stored on file: flash:/TestReport-SU-0.txt Diags completed... Rebooting the system now!!! Mar 12 10:40:35: %S6000:0 %DIAGAGT-6-DA_DIAG_DONE: Diags finished on stack unit 0 Diagnostic results are printed to a file in the flash using the filename format TestReport-SU-.txt.
The following example shows the diag command (standalone unit). Dell#diag stack-unit 1 level0 Warning - diagnostic execution will cause multiple link flaps on the peer side - advisable to shut directly connected ports Proceed with Diags [confirm yes/no]: yes Dell#Dec 15 04:14:07: %S4820:0 %DIAGAGT-6-DA_DIAG_STARTED: Starting diags on stack unit 1 00:12:10 : System may take additional time for Driver Init. 00:12:10 : Approximate time to complete the Diags ...
Test 5.001 - Psu1 Status Monitor Test ............................... NOT PRESENT Test 5 - Psu Status Monitor Test .................................... NOT PRESENT Test 6.000 - Psu0 Fan Speed Monitor Test ............................ PASS diagS6000IsPsuGood[954]: ERROR: Psu:1, Power supply is not present. Test 6.001 - Psu1 Fan Speed Monitor Test ............................ NOT PRESENT Test 6 - Psu Fan Speed Monitor Test ................................. NOT PRESENT Test 7.
Test 18 - CFast Presence Test ....................................... PASS Test 19 - Management Phy Presence Test .............................. PASS Trace Logs In addition to the syslog buffer, Dell Networking OS buffers trace messages which are continuously written by various Dell Networking OS software tasks to report hardware and software events and status information. Each trace message provides the date, time, and name of the Dell Networking OS process. All messages are stored in a ring buffer.
When the system detects a genuine over-temperature condition, it powers off the card. To recognize this condition, look for the following system messages: CHMGR-2-MAJOR_TEMP: Major alarm: chassis temperature high (temperature reaches or exceeds threshold of [value]C) CHMGR-2-TEMP_SHUTDOWN_WARN: WARNING! temperature is [value]C; approaching shutdown threshold of [value]C To view the programmed alarm thresholds levels, including the shutdown value, use the show alarms threshold command.
OID String OID Name Description chSysPortXfpTxPower OID displays the transmitting power of the connected optics. chSysPortXfpRecvTemp OID displays the temperature of the connected optics. Transmitting power .1.3.6.1.4.1.6027.3.10.1.2.5.1.8 Temperature .1.3.6.1.4.1.6027.3.10.1.2.5.1.7 NOTE: These OIDs only generate if you enable the enable opticinfo-update-interval is enabled command. Hardware MIB Buffer Statistics .1.3.6.1.4.1.6027.3.16.1.1.
Physical memory is organized into cells of 128 bytes. The cells are organized into two buffer pools — the dedicated buffer and the dynamic buffer. • • Dedicated buffer — this pool is reserved memory that other interfaces cannot use on the same ASIC or by other queues on the same interface. This buffer is always allocated, and no dynamic re-carving takes place based on changes in interface status. Dedicated buffers introduce a trade-off.
• Reduce the dedicated buffer on all queues/interfaces. • Increase the dynamic buffer on all interfaces. • Increase the cell pointers on a queue that you are expecting will receive the largest number of packets. To define, change, and apply buffers, use the following commands. • Define a buffer profile for the FP queues. CONFIGURATION mode buffer-profile fp fsqueue • Define a buffer profile for the CSF queues.
uplink |csf] linecard port-set buffer-policy from CONFIGURATION mode and no buffer-policy from INTERFACE mode. To display the allocations for any buffer profile, use the show commands. To display the default buffer profile, use the show buffer-profile {summary | detail} command from EXEC Privilege mode. The following example shows viewing the default buffer profile. Dell#show buffer-profile detail interface tengigabitethernet 1/1 Interface Te 1/1 Buffer-profile Dynamic buffer 194.
6 7 3.00 3.00 256 256 Using a Pre-Defined Buffer Profile Dell Networking OS provides two pre-defined buffer profiles, one for single-queue (for example, non-quality-of-service [QoS]) applications, and one for four-queue (for example, QoS) applications. You must reload the system for the global buffer profile to take effect, a message similar to the following displays: % Info: For the global pre-defined buffer profile to take effect, please save the config and reload the system..
interface TenGigabitEthernet 1/10 no ip address Troubleshooting Packet Loss The show hardware stack-unit command is intended primarily to troubleshoot packet loss. To troubleshoot packet loss, use the following commands.
Port# Drops 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 8 0 0 :Ingress Drops :IngMac Drops :Total Mmu Drops :EgMac Drops :Egress 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Example of show hardware drops interface interface Dell#show hardware drops interface tengigabitethernet 2/1 Drops in Interface Te 2/1: --- Ingress Drops --Ingress Drops IBP CBP Full Drops PortSTPnotFwd Drops IPv4 L3 Discards Policy Discards Packets dropped by FP (L2+L3) Drops Port bitmap zero Drops Rx VLAN Drops --- Ingress MAC co
Drops in Interface Te 2/1/1: --- Ingress Drops --Ingress Drops IBP CBP Full Drops PortSTPnotFwd Drops IPv4 L3 Discards Policy Discards Packets dropped by FP (L2+L3) Drops Port bitmap zero Drops Rx VLAN Drops --- Ingress MAC counters--Ingress FCSDrops Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS o
Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS on COS10 HOL DROPS on COS11 HOL DROPS on COS12 HOL DROPS on COS13 HOL DROPS on COS14 HOL DROPS on COS15 HOL DROPS on COS16 HOL DROPS on COS17 TxPurge CellErr Aged Drops --- Egress MAC counters--Egress FCS Drops --- Egress FORWARD PROCESSOR IPv4 L3UC Aged & Drops TTL Threshold Drops INVA
rxPkt(UNIT0) rxPkt(UNIT1) rxPkt(UNIT2) rxPkt(UNIT3) transmitted txRequested noTxDesc txError txReqTooLarge txInternalError txDatapathErr txPkt(COS0) txPkt(COS1) txPkt(COS2) txPkt(COS3) txPkt(COS4) txPkt(COS5) txPkt(COS6) txPkt(COS7) txPkt(UNIT0) :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 Example of Viewing Party Bus Statistics Dell#sh hardware stack-unit 2 cpu party-bus statistics Input Statistics: 27550 packets, 2559298 bytes 0 dropped, 0 errors Output Statistics: 1649566 packets, 193531
RDBGC5.ge0 RDBGC7.ge0 GR64.ge0 GR127.ge0 GR255.ge0 GRPKT.ge0 GRBYT.ge0 GRMCA.ge0 GRBCA.ge0 GT64.ge0 GT127.ge0 GT255.ge0 GT511.ge0 GTPKT.ge0 GTBCA.ge0 GTBYT.ge0 RUC.cpu0 TDBGC6.
TX TX TX TX TX TX TX TX TX - Byte Counter Control frame counter Pause control frame counter Over size packet counter Jabber counter VLAN tag frame counter Double VLAN tag frame counter RUNT frame counter Fragment counter Interface Te 0/1 : Description RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Frame Counter --------------------Interface Fo 0/60 : Description RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Fra
TX TX TX TX TX TX TX - Pause control frame counter Over size packet counter Jabber counter VLAN tag frame counter Double VLAN tag frame counter RUNT frame counter Fragment counter 0 0 0 0 0 0 0 Dell# show hardware stack-unit 1 unit 0 counters Interface Gi 1/1 : Description RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Frame Counter RX - IPV6 L3 routed multicast Packets RX - Unicast Packet Counter RX - 64 Byte Frame Counter RX - 64 to 127 Byte Frame Counter
RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 routed multicast Packets RX - IPV6 L3 Unicast Frame Counter --------------------- 0 0 0 Example of Displaying Counter Information for a Specific Interface Dell#show hardware counters interfac tengigabitethernet 5/1 unit: 0 port: 2 (interface Te 5/1) Description Value RX - IPV4 L3 Unicast Frame Counter RX - IPV4 L3 Routed Multicast Packets RX - IPV6 L3 Unicast Frame Counter RX - IPV6 L3 Routed Multicast Packets RX - Unicast Packet Counter RX - 64 Byte Frame C
• Enable RPM core dumps and specify the Shutdown mode. CONFIGURATION mode logging coredump server To undo this command, use the no logging coredump server command. Mini Core Dumps Dell Networking OS supports mini core dumps on the application and kernel crashes. The mini core dump applies to Master, Standby, and Member units. Application and kernel mini core dumps are always enabled. The mini core dumps contain the stack space and some other minimal information that you can use to debug a crash.
--------------------FREE MEMORY--------------uvmexp.free = 0x2312 Enabling TCP Dumps A TCP dump captures CPU-bound control plane traffic to improve troubleshooting and system manageability. When you enable TCP dump, it captures all the packets on the local CPU, as specified in the CLI. You can save the traffic capture files to flash, FTP, SCP, or TFTP. The files saved on the flash are located in the flash:// TCP_DUMP_DIR/Tcpdump_/ directory and labeled tcpdump_*.pcap.
60 Standards Compliance This chapter describes standards compliance for Dell Networking products. NOTE: Unless noted, when a standard cited here is listed as supported by the Dell Networking Operating System (OS), Dell Networking OS also supports predecessor standards. One way to search for predecessor standards is to use the http://tools.ietf.org/ website. Click “Browse and search IETF documents,” enter an RFC number, and inspect the top of the resulting document for obsolescence citations to related RFCs.
RFC and I-D Compliance Dell Networking OS supports the following standards. The standards are grouped by related protocol. The columns showing support by platform indicate which version of Dell Networking OS first supports the standard. General Internet Protocols The following table lists the Dell Networking OS support per platform for general internet protocols. Table 84. General Internet Protocols RFC# Full Name S-Series 768 User Datagram Protocol 7.6.1 793 Transmission Control Protocol 7.6.
RFC# Full Name S-Series 1042 A Standard for the Transmission of IP Datagrams 7.6.1 over IEEE 802 Networks 1191 Path MTU Discovery 1305 Network Time Protocol (Version 3) Specification, 7.6.1 Implementation and Analysis 1519 Classless Inter-Domain Routing (CIDR): an Address Assignment and Aggregation Strategy 7.6.1 1542 Clarifications and Extensions for the Bootstrap Protocol 7.6.1 1812 Requirements for IP Version 4 Routers 7.6.1 2131 Dynamic Host Configuration Protocol 7.6.
RFC# Full Name S-Series 4862 IPv6 Stateless Address Autoconfiguration 8.3.12.0 5175 IPv6 Router Advertisement Flags Option 8.3.12.0 Border Gateway Protocol (BGP) The following table lists the Dell Networking OS support per platform for BGP protocols. Table 87. Border Gateway Protocol (BGP) RFC# Full Name S-Series/Z-Series 1997 BGP ComAmtturnibituitees 7.8.1 2385 Protection of BGP Sessions via the TCP MD5 Signature Option 7.8.1 2439 BGP Route Flap Damping 7.8.
Intermediate System to Intermediate System (IS-IS) The following table lists the Dell Networking OS support per platform for IS-IS protocol. Table 89.
Multicast The following table lists the Dell Networking OS support per platform for Multicast protocol. Table 91. Multicast RFC# Full Name S-Series 1112 Host Extensions for IP Multicasting 7.8.1 2236 Internet Group Management Protocol, Version 2 7.8.1 2710 Multicast Listener Discovery (MLD) for IPv6 3376 Internet Group Management Protocol, Version 3 7.8.1 3569 An Overview of Source-Specific Multicast (SSM) 7.8.
RFC# Full Name S4810 1850 OSPF Version 2 Management Information Base 7.6.1 1901 Introduction to Communitybased SNMPv2 7.6.1 2011 SNMPv2 Management 7.6.1 Information Base for the Internet Protocol using SMIv2 2012 SNMPv2 Management Information Base for the Transmission Control Protocol using SMIv2 7.6.1 2013 SNMPv2 Management Information Base for the User Datagram Protocol using SMIv2 7.6.1 2024 Definitions of Managed Objects for Data Link Switching using SMIv2 7.6.
RFC# Full Name S4810 2578 Structure of Management Information Version 2 (SMIv2) 7.6.1 2579 Textual Conventions for SMIv2 7.6.1 2580 Conformance Statements for SMIv2 7.6.1 2618 RADIUS Authentication Client MIB, except the following four counters: 7.6.1 S4820T Z-Series 9.5.(0.0) 9.5.(0.0) radiusAuthClientInvalidServerAdd resses radiusAuthClientMalformedAcce ssResponses radiusAuthClientUnknownTypes radiusAuthClientPacketsDropped 2698 A Two Rate Three Color Marker 9.5.(0.
RFC# Full Name S4810 S4820T Z-Series 3418 Management Information Base (MIB) for the Simple Network Management Protocol (SNMP) 7.6.1 3434 Remote Monitoring MIB Extensions for High Capacity Alarms, High-Capacity Alarm Table (64 bits) 7.6.1 3580 IEEE 802.1X Remote Authentication Dial In User Service (RADIUS) Usage Guidelines 7.6.
RFC# Full Name S4810 S4820T Z-Series 9.2.(0.0) 9.2.(0.0) interfaces. Used in the Programmatic Interface RESTAPI feature. IEEE 802.1AB Management Information Base module for LLDP configuration, statistics, local system data and remote systems data components. 7.7.1 IEEE 802.1AB The LLDP Management 7.7.1 Information Base extension module for IEEE 802.1 organizationally defined discovery information. (LLDP DOT1 MIB and LLDP DOT3 MIB) IEEE 802.1AB The LLDP Management 7.7.
RFC# Full Name S4810 FORCE10-LINKAGGMIB Force10 Enterprise Link Aggregation MIB 7.6.1 S4820T Z-Series FORCE10-CHASSIS-MIB Force10 E-Series Enterprise Chassis MIB FORCE10-COPYCONFIG-MIB Force10 File Copy MIB (supporting SNMP SET operation) 7.7.1 FORCE10-MONMIB Force10 Monitoring MIB 7.6.1 FORCE10-PRODUCTSMIB Force10 Product Object Identifier 7.6.1 MIB FORCE10-SS-CHASSIS- Force10 S-Series Enterprise MIB Chassis MIB 7.6.1 FORCE10-SMI Force10 Structure of Management Information 7.6.
