Users Guide

2 drwx 4096 Feb 09 2013 16:07:12 +00:00 ..
3 -rwx 512 Jan 28 2013 10:42:14 +00:00 f10StkUnit9.kcore.mini.txt
4 -rwx 299829760 Jan 22 2013 23:27:46 +00:00 f10StkUnit9.kcore.gz
5 -rwx 471494 Jan 22 2013 23:40:40 +00:00 f10cp_dsm_130122233423_Stk8.acore.gz
6 -rwx 1626169 Jan 22 2013 23:40:46 +00:00 sysdlp_Stk8.acore.gz
7 -rwx 466916 Jan 22 2013 23:49:34 +00:00 f10cp_dsm_130122234622_Stk9.acore.gz
8 -rwx 512 Jan 30 2013 00:41:10 +00:00 f10StkUnit10.kcore.mini.txt
9 -rwx 512 Jan 30 2013 00:49:38 +00:00 f10StkUnit11.kcore.mini.txt
flash: 2143281152 bytes total (1778053120 bytes free)
Dell#
Example of a Mini Core Text File
VALID MAGIC
-----------------PANIC STRING -----------------
panic string is :<null>
---------------STACK TRACE START---------------
0035d60c <f10_save_mmu+0x120>:
00274f8c <panic+0x144>:
0024e2b0 <db_fncall+0x134>:
0024dee8 <db_command+0x258>:
0024d9c4 <db_command_loop+0xc4>:
002522b0 <db_trap+0x158>:
0026a8d0 <mi_switch+0x1b0>:
0026a00c <bpendtsleep>:
----------------STACK TRACE END----------------
--------------------FREE MEMORY---------------
uvmexp.free = 0x2312
Enabling TCP Dumps
A TCP dump captures CPU-bound control plane trac to improve troubleshooting and system manageability. When you enable TCP
dump, it captures all the packets on the local CPU, as specied in the CLI.
You can save the trac capture les to ash, FTP, SCP, or TFTP. The les saved on the ash are located in the ash://
TCP_DUMP_DIR/Tcpdump_<time_stamp_dir>/ directory and labeled tcpdump_*.pcap. There can be up to 20
Tcpdump_<time_stamp_dir> directories. The 21st le overwrites the oldest saved le. The maximum le size for a TCP dump
capture is 1MB. When a le reaches 1MB, a new le is created, up to the specied total number of les.
Maximize the number of packets recorded in a le by specifying the snap-length to capture the le headers only.
The tcpdump command has a nite run process. When you enable the tcpdump command, it runs until the capture-duration timer
and/or the packet-count counter threshold is met. If you do not set a threshold, the system uses a default of a 5 minute capture-
duration and/or a single 1k le as the stopping point for the dump.
You can use the capture-duration timer and the packet-count counter at the same time. The TCP dump stops when the rst of the
thresholds is met. That means that even if the duration timer is 9000 seconds, if the maximum le count parameter is met rst, the
dumps stop.
To enable a TCP dump, use the following command.
• Enable a TCP dump for CPU bound trac.
CONFIGURATION mode
tcpdump cp [capture-duration time | filter expression | max-file-count value | packet-
count value | snap-length value | write-to path]
S5000 Debugging and Diagnostics
1019