Administrator Guide

MIB Object OID Description
dot3adAggPartnerSystemPriority 1.2.840.10006.300.43.1.1.1.1.8 Contains a two octet read–only value that
indicates the priority value associated with
the Partner’s system ID.
dot3adAggPartnerOperKey 1.2.840.10006.300.43.1.1.1.1.9 Contains the current operational value of the
key for the Aggregator’s current protocol
partner.
dot3adAggCollectorMaxDelay 1.2.840.10006.300.43.1.1.1.1.10 Contains a 16–bit read–write attribute
dening the maximum delay, in tens of
microseconds, that may be imposed by the
frame collector between receiving a frame
from an Aggregator Parser, and either
delivering the frame to its MAC Client or
discarding the frame.
dot3adAggPortListTable 1.2.840.10006.300.43.1.1.2 Contains a list of all the ports associated
with each Aggregator. Each LACP channel in
a device occupies an entry in the table.
dot3adAggPortListEntry 1.2.840.10006.300.43.1.1.2.1 Contains a list of ports associated with a
given Aggregator and indexed by the
ifIndex of the Aggregator.
dot3adAggPortListPorts 1.2.840.10006.300.43.1.1.2.1.1 Contains a complete set of ports currently
associated with the Aggregator.
Viewing the LAG MIB
• To view the LAG MIB generated by the system, use the following command.
snmpbulkget -v 2c -c LagMIB 10.16.148.157 1.2.840.10006.300.43.1.1.1.1.1
iso.2.840.10006.300.43.1.1.1.1.1.1258356224 = Hex-STRING: 00 01 E8 8A E8 46
iso.2.840.10006.300.43.1.1.1.1.1.1258356736 = Hex-STRING: 00 01 E8 8A E8 46
iso.2.840.10006.300.43.1.1.1.1.2.1258356224 = INTEGER: 32768
iso.2.840.10006.300.43.1.1.1.1.2.1258356736 = INTEGER: 32768
iso.2.840.10006.300.43.1.1.1.1.3.1258356224 = Hex-STRING: 00 01 E8 8A E8 44
iso.2.840.10006.300.43.1.1.1.1.3.1258356736 = Hex-STRING: 00 01 E8 8A E8 44
iso.2.840.10006.300.43.1.1.1.1.4.1258356224 = INTEGER: 1
iso.2.840.10006.300.43.1.1.1.1.4.1258356736 = INTEGER: 1
iso.2.840.10006.300.43.1.1.1.1.5.1258356224 = INTEGER: 127
iso.2.840.10006.300.43.1.1.1.1.5.1258356736 = INTEGER: 128
Manage VLANs using SNMP
The qBridgeMIB managed objects in Q-BRIDGE-MIB, dened in RFC 2674, allows you to use SNMP to manage VLANs.
Creating a VLAN
To create a VLAN, use the dot1qVlanStaticRowStatus object.
The snmpset operation shown in the following example creates VLAN 10 by specifying a value of 4 for instance 10 of the
dot1qVlanStaticRowStatus object.
Example of Creating a VLAN using SNMP
> snmpset -v2c -c mycommunity 123.45.6.78 .1.3.6.1.2.1.17.7.1.4.3.1.5.10 i 4
SNMPv2-SMI::mib-2.17.7.1.4.3.1.5.10 = INTEGER: 4
872
Simple Network Management Protocol (SNMP)