Users Guide
seq 10 deny ip any any
Dell# show cam layer3-qos interface gigabitethernet 2/4
Cam Port Dscp Proto Tcp Src Dst SrcIp DstIp DSCP Queue
Index Flag Port Port Marking
-----------------------------------------------------------------------
20416 1 18 IP 0x0 0 0 23.64.0.5/32 0.0.0.0/0 20 2
20417 1 18 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 - 0
20418 1 0 IP 0x0 0 0 23.64.0.2/32 0.0.0.0/0 10 1
20419 1 0 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 - 0
20420 1 0 IP 0x0 0 0 23.64.0.3/32 0.0.0.0/0 12 1
20421 1 0 IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 - 0
20422 1 10 0 0x0 0 0 0.0.0.0/0 0.0.0.0/0 14 1
24511 1 0 0 0x0 0 0 0.0.0.0/0 0.0.0.0/0 - 0
In the previous example, the ClassAF1 does not classify traffic as intended. Traffic matching the first match criteria is classified to Queue 1,
but all other traffic is classified to Queue 0 as a result of CAM entry 20419.
When you remove the explicit “deny any” rule from all three ACLs, the CAM reflects exactly the desired classification.
The following example shows correct traffic classifications.
Dell#show cam layer3-qos interface gigabitethernet 2/4
Cam Port Dscp Proto Tcp Src Dst SrcIp DstIp DSCP Queue
Index Flag Port Port Marking
-------------------------------------------------------------------------
20416 1 18 IP 0x0 0 0 23.64.0.5/32 0.0.0.0/0 20 2
20417 1 0 IP 0x0 0 0 23.64.0.2/32 0.0.0.0/0 10 1
20418 1 0 IP 0x0 0 0 23.64.0.3/32 0.0.0.0/0 12 1
20419 1 10 0 0x0 0 0 0.0.0.0/0 0.0.0.0/0 14 1
24511 1 0 0 0x0 0 0 0.0.0.0/0 0.0.0.0/0 - 0
Create a QoS Policy
There are two types of QoS policies — input and output.
Input QoS policies regulate Layer 3 and Layer 2 ingress traffic. The regulation mechanisms for input QoS policies are rate policing and
setting priority values.
• Layer 3 — QoS input policies allow you to rate police and set a DSCP or dot1p value. In addition, you can configure a drop precedence
for incoming packets based on their DSCP value by using a DSCP color map. For more information, see DSCP Color Maps.
• Layer 2 — QoS input policies allow you to rate police and set a dot1p value.
Output QoS policies regulate egress traffic. The regulation mechanisms for output QoS policies are bandwidth percentage, scheduler
strict, rate shaping and WRED.
NOTE:
When changing a "service-queue" configuration in a QoS policy map, all QoS rules are deleted and re-added
automatically to ensure that the order of the rules is maintained. As a result, the Matched Packets value shown in the
show qos statistics command is reset.
NOTE: To avoid issues misconfiguration causes, Dell Networking recommends configuring either DCBX or Egress QoS
features, but not both simultaneously. If you enable both DCBX and Egress QoS at the same time, the DCBX
configuration is applied and unexpected behavior occurs on the Egress QoS.
Creating an Input QoS Policy
To create an input QoS policy, use the following steps.
1. Create a Layer 3 input QoS policy.
CONFIGURATION mode
qos-policy-input
Create a Layer 2 input QoS policy by specifying the keyword layer2 after the qos-policy-input command.
2. After you create an input QoS policy, do one or more of the following:
Configuring Policy-Based Rate Policing
Setting a dot1p Value for Egress Packets
550
Quality of Service (QoS)