Service Manual
• the next 1 bit is 0 for a physical interface and 1 for a logical interface
• the next 1 bit is unused
For example, the index 72925242 is 100010110001100000000111010 in binary. The binary interface index for TeGigabitEthernet 1/21
of a 48-port 10/100/1000Base-T line card with RJ-45 interface. Notice that the physical/logical bit and the nal, unused bit are not
given. The interface is physical, so represent this type of interface by a 0 bit, and the unused bit is always 0. These 2 bits are not
given because they are the most signicant bits, and leading zeros are often omitted.
NOTE: The interface index does not change if the interface reloads or fails over. If the unit is renumbered (for any
reason) the interface index changes during a reload.
To display the interface number, use the following command.
• Display the interface index number.
EXEC Privilege mode
show interface
Example of Deriving the Interface Index Number
To view the system image on Flash Partition A, use the chSysSwInPartitionAImgVers object or, to view the system image on Flash
Partition B, use the chSysSwInPartitionBImgVers object.
Table 64. MIB Objects for Viewing the System Image on Flash Partitions
MIB Object OID Description MIB
chSysSwInPartitionAImgVers 1.3.6.1.4.1.6027.3.10.1.2.8.1.11 List the version string of the
system image in Flash Partition
A.
Chassis MIB
chSysSwInPartitionBImgVers 1.3.6.1.4.1.6027.3.10.1.2.8.1.12 List the version string of the
system image in Flash Partition
B.
Chassis MIB
The system image can also be retrieved by performing an SNMP walk on the following OID: MIB Object is chSysSwModuleTable and
the OID is 1.3.6.1.4.1.6027.3.10.1.2.8.
Dell#show interface Gigabitethernet 1/21
GigabitEthernet 1/21 is up, line protocol is up
Monitor Port-Channels
To check the status of a Layer 2 port-channel, use f10LinkAggMib (.1.3.6.1.4.1.6027.3.2). In the following example, Po 1 is a switchport
and Po 2 is in Layer 3 mode.
Example of SNMP Trap for Monitored Port-Channels
[senthilnathan@lithium ~]$ snmpwalk -v 2c -c public 10.11.1.1 .1.3.6.1.4.1.6027.3.2.1.1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.1 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.2 = INTEGER: 2
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.1 = Hex-STRING: 00 01 E8 13 A5 C7
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.2 = Hex-STRING: 00 01 E8 13 A5 C8
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.1 = INTEGER: 1107755009
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.2 = INTEGER: 1107755010
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.1 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.2 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.1 = Hex-STRING: 00 00
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.2 = Hex-STRING: 00 00
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.1 = STRING: "Gi 5/84 "
<< Channel member for Po1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.2 = STRING: "Gi 5/85 " << Channel member for Po2
dot3aCommonAggFdbIndex
SNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.1.1107755009.1 = INTEGER: 1107755009
Simple Network Management Protocol (SNMP)
723