Users Guide
Field Description
Destination Lists the destination IP address.
Gateway Displays either the word “direct” and an interface for a directly connected route or the
remote IP address used to forward the traffic.
First-Hop Displays the first hop IP address.
Mac-Addr Displays the MAC address.
Port Displays the egress-port information.
VId Displays the VLAN ID. If no VLAN is assigned, zero (0) is listed.
EC Displays the number of ECMP paths.
If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named W-
EC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is
assigned with a weight.
Example
Dell# show ip fib stack-unit 1
Destination Gateway First-Hop Mac-Addr Port VId EC
------------------------------------------------------------------------------------
1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 0
2.1.1.2/32 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 0
0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0
1.1.1.0/24 Direct, Vl 1000 0.0.0.0 00:00:00:00:00:00 CP 1000 0
1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0
2.1.1.0/24 Direct, Vl 20 0.0.0.0 00:00:00:00:00:00 CP 20 0
2.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0
100.1.1.0/24 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 1
100.1.1.0/24 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 1
Dell#
Dell# show ip route
S 10.1.1.0/24 via 1.1.1.2, Vl 10
via 2.1.1.2, Vl 20
S 20.1.1.0/24 via 3.1.1.2, Vl 30
S 100.1.1.0/24 via 10.1.1.0, weight 7
via 20.1.1.0, weight 1
Example (Show
command output
with Weighted
ECMP Enabled)
Dell# show ip fib stack-unit 1
Destination Gateway First-Hop Mac-Addr Port VId EC RC W
------------------------------------------------------------------------------
0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 - -
1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - -
1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 - -
The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp
weighted command.
Related Commands
• clear ip fib stack-unit — clear FIB entries on a specified stack-unit.
• ip ecmp weighted— enable weighted ECMP calculations.
show ip flow
Show how a Layer 3 packet is forwarded when it arrives at a particular interface.
Syntax
show ip flow interface interface {source-ip address destination-ip address}
{protocol number [tcp | udp]} {src-port number destination-port number}
Parameters
interface interface Enter the keyword interface then one of the following interface keywords.
772 IPv4 Routing