Users Guide

58 Dell EMC PowerEdge MX SmartFabric Configuration Guide with Cisco ACI
5.2.6 show interface port channel summary
The show interface port-channel summary command shows the LAG number (VLT port channel 1
in this example), the mode, status and ports used in the port channel.
MX9116n-1# show interface port-channel summary
LAG Mode Status Uptime Ports
1 L2-HYBRID up 00:29:20 Eth 1/1/41 (Up)
Eth 1/1/42 (Up)
5.2.7 show lldp neighbors
The show lldp neighbors command shows information about directly connected devices. Ports 1/1/1,
1/1/5, 1/71/1, and 1/71/3 are connected to the four compute sleds.
Note: Ports 1/71/1 and 1/71/3 are the compute sleds connected to the MX7116n FEM in the other
chassis.
Two instances display for each port connected to a compute sled. One instance is the compute sled iDRAC.
The iDRAC uses connectivity to the mezzanine card to advertise LLDP information. It includes the iDRAC
name in the Rem Host Name column, the sled service tag and mezzanine card number-port-partition in the
Rem Port ID column, and the iDRAC MAC address in the Rem Chassis Id column. The second
instance is the mezzanine card itself and the MAC address of the mezzanine card port is shown.
Ports 1/1/37-1/1/40 are the VLTi interfaces for the SmartFabric. Ports 1/1/43-1/1/44 are the links in
VLT port channel 1 connected to the Cisco ACI leaf switches.
MX9116n-1# show lldp neighbors
Loc PortID Rem Host Name Rem Port Id Rem Chassis Id
--------------------------------------------------------------------------------
ethernet1/1/1 Not Advertised f4:e9:d4:f2:6f:26 f4:e9:d4:f2:6f:26
ethernet1/1/1 MX740c-1-1-idrac ST0000C NIC.Mezzanine.1A-1-1 d0:94:66:2d:b3:f4
ethernet1/1/3 Not Advertised 24:6e:96:9c:e5:da 24:6e:96:9c:e5:da
ethernet1/1/3 MX740c-1-3-idrac 1S34MN2 NIC.Mezzanine.1A-1-1 d0:94:66:29:ff:27
ethernet1/1/37 MX9116n-2 ethernet1/1/37 20:04:0f:00:9d:1e
ethernet1/1/38 MX9116n-2 ethernet1/1/38 20:04:0f:00:9d:1e
ethernet1/1/39 MX9116n-2 ethernet1/1/39 20:04:0f:00:9d:1e
ethernet1/1/40 MX9116n-2 ethernet1/1/40 20:04:0f:00:9d:1e
ethernet1/1/41 Leaf1 Eth1/51 00:be:75:19:40:13
ethernet1/1/42 Leaf2 Eth1/51 4c:77:6d:f1:ee:7d
ethernet1/71/1 Not Advertised f4:e9:d4:f2:6f:da f4:e9:d4:f2:6f:da
ethernet1/71/1 MX840c-2-1-idrac ST00000 NIC.Mezzanine.1A-1-1 d0:94:66:2d:b5:2c
ethernet1/71/3 Not Advertised 24:6e:96:9c:e5:48 24:6e:96:9c:e5:48
ethernet1/71/3 MX740c-2-3-idrac 1S35MN2 NIC.Mezzanine.1A-1-1 d0:94:66:29:fa:f4
5.2.8 show qos system
The show qos system command displays the QoS configuration applied to the system. The command is
useful to verify the service policy created automatically by the SmartFabric deployment.