Owners Manual
Table Of Contents
- Dell EMC PowerEdge MX750c Installation and Service Manual
- Contents
- About this document
- Dell EMC PowerEdge MX750c system overview
- Initial system setup and configuration
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- PowerEdge MX750c sled
- Sled cover
- Air shroud
- Processor and memory module blank
- Drives
- Drive backplane
- Cable routing
- Drive cage
- Control panel
- System memory
- Processor and heat sink module
- PERC card
- Optional IDSDM module
- M.2 BOSS card
- Mezzanine cards
- Optional internal USB memory key
- System battery
- System board
- Trusted Platform Module
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Table 32. PERC H755 MX upgrade kit (continued)
Backplane
configuration
Upgrade from: Upgrade to: Disconnect and
remove card or
cables from the
connector (cable
marking):
Replace with the
card or cables
(cable marking):
Refer to cabling
configurations
with H755 MX + on
board PCIe
H755 MX (NVME
HW RAID)
● H745P MX card
● Jumbo SAS
cable (BP SA1–
CTRL_SA1)
● PCIE1 cable
(MB SL1 – BP
PA1)
● PCIE2 cable
(MB SL2 – BP
PB1)
● H755 MX card
● PCIEA cable
(CTRL_PA1 –
BP PA1 and BP
PB1)
Cable routing
> PCIe cabling
diagram of
configuration 12
- 4 x 2.5-inch
Universal backplane
with H755 MX
X6 SAS/SATA
backplane
Onboard SATA/
SWRAID
H755 MX (SAS
Controller)
● SATA cable
(MB SL6 – BP
SA1)
● H755 MX card
● SAS cable
(CTRL_SA1 –
BP SA1)
Cable routing
> SAS cabling
diagram of
configuration 6 -
6 x 2.5-inch SAS/
SATA backplane
with H755 MX
H745PMX (Jumbo
PERC)
H755 MX (SAS
Controller)
● H745P MX card
● Jumbo SAS
cable (BP SA1 –
CTRL_SA1)
● H755 MX card
● SAS cable
(CTRL_SA1 –
BP SA1)
Cable routing
> SAS cabling
diagram of
configuration 6 -
6 x 2.5-inch SAS/
SATA backplane
with H755 MX
PERC H745P MX Upgrade kit
The below table provides the upgrade kit information about PERC H745P MX available After Point of Sale (APOS):
Table 33. PERC H745P MX upgrade kit
Backplane
configuration
Upgrade from: Upgrade to: Disconnect and
remove card or
cables from the
connector (cable
marking):
Replace with the
card or cables
(cable marking):
Refer to cabling
configurations
X4 Universal
backplane
Onboard SATA/
SWRAID/NVME
H745P MX (Jumbo
PERC)
SATA cable (MB
SL6 – BP SA1)
● H745P MX card
● Jumbo SAS
cable
(CTRL_SA1 –
BP SA1)
Cable routing
> SAS/PCIe
cabling diagram of
configuration 10
- 4 x 2.5-inch
Universal backplane
with H745P MX
(Jumbo PERC) +
on board PCIe
HBA350i (SAS
Controller /Non–
RAID)
H745P MX (Jumbo
PERC)
● HBA350i card
● SAS cable
(CTRL_SA1 –
BP SA1)
● FabC MMZ
card if present
● H745P MX card
● Jumbo SAS
cable
(CTRL_SA1 –
BP SA1)
Cable routing
> SAS/PCIe
cabling diagram of
configuration 10
- 4 x 2.5-inch
Universal backplane
102 Upgrade Kits