Users Guide

– A VLT domain consists of the two core chassis, the interconnect trunk, backup link, and the LAG members connected to
attached devices.
– Each VLT domain has a unique MAC address that you create or VLT creates automatically.
– ARP tables are synchronized between the VLT peer nodes.
– VLT peer switches operate as separate chassis with independent control and data planes for devices attached on non-VLT
ports.
– One chassis in the VLT domain is assigned a primary role; the other chassis takes the secondary role. The primary and
secondary roles are required for scenarios when connectivity between the chassis is lost. VLT assigns the primary chassis
role according to the lowest MAC address. You can congure the primary role.
– In a VLT domain, the peer switches must run the same Dell Networking OS software version.
– Separately congure each VLT peer switch with the same VLT domain ID and the VLT version. If the system detects
mismatches between VLT peer switches in the VLT domain ID or VLT version, the VLT Interconnect (VLTi) does not activate.
To nd the reason for the VLTi being down, use the show vlt statistics command to verify that there are mismatch
errors, then use the show vlt brief command on each VLT peer to view the VLT version on the peer switch. If the VLT
version is more than one release dierent from the current version in use, the VLTi does not activate.
– The chassis members in a VLT domain support connection to orphan hosts and switches that are not connected to both
switches in the VLT core.
• VLT interconnect (VLTi)
– The VLT interconnect supports a maximum of two 10G ports.
– In VLT mode, port 33 and 37 are dedicated to VLT interconnect ports.
– A VLT interconnect over 1G ports is not supported.
– The port channel must be in Default mode (not Switchport mode) to have VLTi recognize it.
– The system automatically includes the required VLANs in VLTi. You do not need to manually select VLANs.
– VLT peer switches operate as separate chassis with independent control and data planes for devices attached to non-VLT
ports.
– Port-channel link aggregation (LAG) across the ports in the VLT interconnect is required; individual ports are not supported.
Dell Networking strongly recommends conguring a static LAG for VLTi.
– The VLT interconnect synchronizes L2 and L3 control-plane information across the two chassis.
– The VLT interconnect is used for data trac only when there is a link failure that requires using VLTi in order for data packets
to reach their nal destination.
– Unknown, multicast, and broadcast trac can be ooded across the VLT interconnect.
– MAC addresses for VLANs congured across VLT peer chassis are synchronized over the VLT interconnect on an egress port
such as a VLT LAG. MAC addresses are the same on both VLT peer nodes.
– ARP entries congured across the VLTi are the same on both VLT peer nodes.
– If you shut down the port channel used in the VLT interconnect on a peer switch in a VLT domain in which you did not
congure a backup link, the switch’s role displays in the show vlt brief command output as Primary instead of
Standalone.
– When you change the default VLAN ID on a VLT peer switch, the VLT interconnect may ap.
– In a VLT domain, the following software features are supported on VLTi: link layer discovery protocol (LLDP), ow control,
port monitoring, jumbo frames, and data center bridging (DCB).
– When you enable the VLTi link, the link between the VLT peer switches is established if the following congured information
is true on both peer switches:
* the VLT system MAC address matches.
* the VLT unit-id is not identical.
NOTE: If you congure the VLT system MAC address or VLT unit-id on only one of the VLT peer switches, the link
between the VLT peer switches is not established. Each VLT peer switch must be correctly congured to establish
the link between the peers.
– If the link between the VLT peer switches is established, changing the VLT system MAC address or the VLT unit-id causes
the link between the VLT peer switches to become disabled. However, removing the VLT system MAC address or the VLT
unit-id may disable the VLT ports if you happen to congure the unit ID or system MAC address on only one VLT peer at any
time.
244
PMUX Mode of the IO Aggregator