Users Guide
Table Of Contents
- Dell PowerEdge Command Line Reference Guide for the M I/O Aggregator 9.14.0.0
- About this Guide
- Before You Start
- CLI Basics
- File Management
- Control and Monitoring
- asset-tag
- clear alarms
- clear command history
- configure
- debug cpu-traffic-stats
- debug ifm trace-flags
- disable
- enable
- end
- exit
- feature unique-name
- ftp-server enable
- ftp-server topdir
- ftp-server username
- hostname
- http-server
- ip telnet server enable
- ip telnet source-interface
- line
- ping
- reload
- service timestamps
- show alarms
- show command-history
- show configuration lock
- show cpu-traffic-stats
- show debugging
- show diag
- show environment
- show inventory
- show memory
- show processes cpu
- show processes ipc flow-control
- show processes memory
- show reset-reason
- show revision
- show server-interfaces
- show system
- show tech-support
- show uplink brief
- show util-threshold cpu
- show util-threshold memory
- ssh-peer-stack-unit
- telnet
- telnet-peer-stack-unit
- terminal length
- terminal monitor
- terminal xml
- trace route
- undebug all
- write
- u-Boot
- boot change
- boot selection
- boot show net config retries
- boot write net config retries
- boot zero
- default gateway
- enable
- help
- ignore enable password
- ignore startup-config
- interface management ethernet ip address
- no default gateway
- no interface management ethernet ip address
- reload
- show boot blc
- show boot selection
- show bootflash
- show bootvar
- show default gateway
- show interface management ethernet
- show interface management port config
- syntax help
- Configuration Cloning
- Data Center Bridging (DCB)
- Fibre Channel over Ethernet for FC Flex IO Modules
- advertise dcbx-appln-tlv
- advertise dcbx-tlv
- bandwidth-percentage
- clear dcbx counters
- clear ets counters
- clear pfc counters
- dcb-enable
- dcb enable pfc-queues
- dcb enable auto-detect on-next-reload
- dcb-map stack-unit all stack-ports all
- dcb pfc-shared-buffer-size
- dcb pfc-total-buffer-size
- dcb-buffer-threshold
- dcb-policy buffer-threshold (Global Configuration)
- service-class buffer shared-threshold-weight
- dcbx-port role
- dcbx version
- debug dcbx
- fc-map
- fcoe-map
- fcoe priority-bits
- iscsi priority-bits
- keepalive
- interface vlan (NPIV proxy gateway)
- pfc mode on
- pfc no-drop queues
- pfc priority
- priority-group
- priority-group bandwidth pfc
- priority-pgid
- qos-policy-output ets
- scheduler
- show dcb
- show interface dcbx detail
- show interface ets
- show interface pfc
- show interface pfc statistics
- show qos dcb-map
- show stack-unit stack-ports ets details
- show stack-unit stack-ports pfc details
- Dynamic Host Configuration Protocol
- FC Flex IO Modules
- FC FLEXIO FPORT
- FIP Snooping
- Internet Group Management Protocol (IGMP)
- IGMP Commands
- IGMP Snooping Commands
- clear ip igmp groups
- debug ip igmp
- ip igmp group-join-limit
- ip igmp querier-timeout
- ip igmp query-interval
- ip igmp query-max-resp-time
- ip igmp snooping enable
- ip igmp snooping fast-leave
- ip igmp snooping flood
- ip igmp snooping last-member-query-interval
- ip igmp snooping mrouter
- ip igmp snooping querier
- ip igmp version
- show ip igmp groups
- show ip igmp interface
- show ip igmp snooping mrouter
- Interfaces
- Port Interface Commands
- Port Channel Commands
- Time Domain Reflectometer (TDR) Commands
- Virtual LAN (VLAN) Commands
- auto vlan
- channel-member
- clear counters
- clear mac-address-table dynamic
- default vlan-id
- description
- feature fc
- flowcontrol
- interface
- interface ManagementEthernet
- interface port-channel
- interface range
- interface vlan
- intf-type cr4 autoneg
- keepalive
- minimum-links
- monitor interface
- mtu
- name
- negotiation auto
- remote-fault-signaling rx
- show config (INTERFACE mode)
- show config (from INTERFACE RANGE mode)
- show config (from INTERFACE VLAN mode)
- show config (from PROTOCOL LLDP mode)
- show interfaces
- show interfaces configured
- show interfaces description
- show interfaces port-channel
- show interfaces stack-unit
- show interfaces status
- show interfaces switchport
- show tdr
- show vlan
- shutdown
- source (port monitoring for 40-Gigabit Ethernet)
- speed (for 1000/10000 interfaces)
- stack-unit portmode
- wavelength
- tdr-cable-test
- vlan tagged (CMC)
- vlan untagged (CMC)
- IPv4 Routing
- iSCSI Optimization
- Isolated Networks
- Link Aggregation Control Protocol (LACP)
- auto-lag enable
- clear lacp counters
- debug lacp
- delay-restore abort-threshold
- io-aggregator auto-lag enable
- lacp link-fallback
- lacp long-timeout
- lacp port-priority
- port-channel mode
- port-channel-protocol lacp
- show interfaces port-channel
- show io-aggregator auto-lag status
- show lacp
- show link-bundle-distribution port-channel
- show port-channel-flow
- Layer 2
- Link Layer Discovery Protocol (LLDP)
- Object Tracking
- Port Monitoring
- Quality of Service (QoS)
- Per-Port QoS Commands
- Policy-Based QoS Commands
- bandwidth-percentage
- description
- dot1p-priority
- policy-aggregate
- policy-map-output
- qos-policy-output
- rate-shape
- service-class bandwidth-percentage
- service-class dot1p-mapping
- service-class dynamic dot1p
- service-policy output
- service-queue
- show qos dcb-map
- show qos dot1p-queue-mapping
- show qos qos-policy-output
- Security
- Simple Network Management Protocol (SNMP) and Syslog
- Stacking Commands
- Storm Control
- SupportAssist
- System Time
- Uplink Failure Detection (UFD)
- Virtual Link Trunking (VLT)
- Debugging and Diagnostics
- Offline Diagnostic Commands
- Hardware Commands
- clear hardware stack-unit
- diag stack-unit
- hardware watchdog
- offline stack-unit
- show diag
- show hardware stack-unit
- show hardware counters interface
- show hardware buffer interface
- show hardware system-flow
- show hardware buffer-stats-snapshot
- show hardware stack-unit buffer-stats-snapshot (Total Buffer Information)
- show hardware drops
- Internet Control Message Protocol (ICMP) Message Types
Defaults None
Command Modes INTERFACE FIBRE_CHANNEL
Supported Modes Programmable-Mux (PMUX)
Command History
Version Description
9.3(0.0) Introduced on the M I/O Aggregator and MXL 10/40GbE Switch with the FC Flex IO
module.
Usage Information
An FCoE map is a template used to map FCoE and FC parameters in a converged fabric. An FCoE map is used to
virtualize upstream FC ports on an M I/O Aggregator with the FC Flex IO module NPIV proxy gateway so that they
appear to downstream server CNA ports as FCoE forwarder (FCF) ports on an FCoE network. When applied to FC
and Ethernet ports on an NPIV proxy gateway, an FCoE map allows the switch to operate as an FCoE-FC bridge
between an FC SAN and an FCoE network by providing FCoE-enabled servers and switches with the necessary
parameters to log in to a SAN fabric. Use the fcoe-map command to create an FCoE map.
On an M I/O Aggregator with the FC Flex IO module NPIV proxy gateway, you cannot apply an FCoE map on
fabric-facing FC ports and server-facing Ethernet ports.
After you apply an FCoE map on an FC interface, when the port is enabled (no shutdown), the NPIV proxy
gateway starts sending FIP multicast advertisements on behalf of the FC port to downstream servers in order to
advertise the availability of a new FCF port on the FCoE VLAN.
To remove an FCoE map from an FC interface, enter the no fabric map-name command in Interface
conguration mode.
Related Commands
fcoe-map — creates an FCoE map which contains the parameters used in the communication between servers
and a SAN fabric.
show fcoe-map— displays the Fibre Channel and FCoE conguration parameters in FCoE maps.
fabric-id vlan
In an FCoE map, congure the association between the dedicated VLAN used to carry FCoE trac between servers and a SAN, and the
fabric where the desired storage arrays are installed.
M I/O Aggregator with the FC Flex IO module
Syntax
fabric-id fabric-num vlan vlan-id
Parameters
fabric-id fabric-num Enter a fabric ID number that is the same as the ID number of the dedicated VLAN used
to carry FCoE storage trac to the fabric specied in the FCoE map. You can enter a
fabric ID in the range 1–4094.
vlanvlan-id Enter the ID number of the dedicated VLAN used to carry FCoE storage trac between
servers and a SAN fabric and specied with the vlan command in the FCoE map.
Defaults None
Command Modes FCOE MAP
FC Flex IO Modules 145