Server Hardware Owner's Manual
Table Of Contents
- About Your System
- Accessing System Features During Startup
- Front-Panel Features and Indicators
- LCD Panel Features (Optional)
- Hard-Drive Status Indicators
- Back-Panel Features and Indicators
- Guidelines for Connecting External Devices
- NIC Indicator Codes
- Power Indicator Codes
- Diagnostic Lights (Optional)
- LCD Status Messages (Optional)
- System Messages
- Warning Messages
- Diagnostics Messages
- Alert Messages
- Using the System Setup Program and UEFI Boot Manager
- Installing System Components
- Recommended Tools
- Inside the System
- Front Bezel (Optional)
- Opening and Closing the System
- Optical Drive (Optional)
- Hard Drives
- Removing a Drive Blank
- Installing a Drive Blank
- Removing a Hard-Drive Carrier
- Installing a Hard-Drive Carrier
- Removing a Hard Drive From a Hard-Drive Carrier
- Installing a Hard Drive Into a Hard-Drive Carrier
- Removing a Cabled Hard Drive
- Installing a Cabled Hard Drive
- Removing a Hard Drive From a Hard-Drive Bracket
- Installing a Hard Drive Into a Hard-Drive Bracket
- Expansion Card
- Expansion-Card Riser
- Internal USB Memory Key
- Cooling Shroud
- Integrated Storage Controller Card
- System Memory
- Cooling Fans
- iDRAC6 Express Card (Optional)
- iDRAC6 Enterprise Card (Optional)
- VFlash Media (Optional)
- Processor
- Power Supplies
- System Battery
- Control Panel Assembly
- SAS Backplane
- Power Distribution Board
- System Board
- Troubleshooting Your System
- Safety First-For You and Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting the Video Subsystem
- Troubleshooting a USB Device
- Troubleshooting a Serial I/O Device
- Troubleshooting a NIC
- Troubleshooting a Wet System
- Troubleshooting a Damaged System
- Troubleshooting the System Battery
- Troubleshooting Power Supply
- Troubleshooting System Cooling Problems
- Troubleshooting a Fan
- Troubleshooting System Memory
- Troubleshooting an Internal USB Key
- Troubleshooting an Optical Drive
- Troubleshooting a Tape Backup Unit
- Troubleshooting a Hard Drive
- Troubleshooting an Expansion Card
- Troubleshooting the Processor
- Running the System Diagnostics
- Jumpers and Connectors
- Getting Help
- Index
About Your System 43
Memory set to
minimum
frequency.
The memory frequency may
be intentionally set lower for
power conservation.
If not an intentional setting,
check any other system
messages for possible causes.
The current memory
configuration may support
only the minimum frequency.
Ensure that your memory
configuration supports the
higher frequency.
See "General Memory
Module Installation
Guidelines" on page 106.
Memory tests
terminated by
keystroke.
POST memory test was
terminated by pressing the
spacebar.
Information only.
MEMTEST lane
failure detected
on
x.
Invalid memory
configuration. Mismatched
memory modules are
installed.
Ensure that the memory
modules are installed in a
valid configuration.
See "General Memory
Module Installation
Guidelines" on page 106.
No boot device
available.
Faulty or missing optical
drive subsystem, hard drive,
or hard drive subsystem, or
no bootable USB key
installed.
Use a bootable USB key,
optical drive, or hard drive.
If the problem persists,
see "Troubleshooting an
Optical Drive" on page 156,
"Troubleshooting a USB
Device" on page 146,
"Troubleshooting an Internal
USB Key" on page 155, and
"Troubleshooting a Hard
Drive" on page 158.
See "Using the System Setup
Program and UEFI Boot
Manager" on page 53 for
information on setting the
order of boot devices.
Table 1-3. System Messages (continued)
Message Causes Corrective Actions
R310HOM.book Page 43 Thursday, March 4, 2010 1:03 AM