Server Hardware Owner's Manual
Table Of Contents
- About Your System
- Accessing System Features During Startup
- Front-Panel Features and Indicators
- LCD Panel Features (Optional)
- Hard-Drive Status Indicators
- Back-Panel Features and Indicators
- Guidelines for Connecting External Devices
- NIC Indicator Codes
- Power Indicator Codes
- Diagnostic Lights (Optional)
- LCD Status Messages (Optional)
- System Messages
- Warning Messages
- Diagnostics Messages
- Alert Messages
- Using the System Setup Program and UEFI Boot Manager
- Installing System Components
- Recommended Tools
- Inside the System
- Front Bezel (Optional)
- Opening and Closing the System
- Optical Drive (Optional)
- Hard Drives
- Removing a Drive Blank
- Installing a Drive Blank
- Removing a Hard-Drive Carrier
- Installing a Hard-Drive Carrier
- Removing a Hard Drive From a Hard-Drive Carrier
- Installing a Hard Drive Into a Hard-Drive Carrier
- Removing a Cabled Hard Drive
- Installing a Cabled Hard Drive
- Removing a Hard Drive From a Hard-Drive Bracket
- Installing a Hard Drive Into a Hard-Drive Bracket
- Expansion Card
- Expansion-Card Riser
- Internal USB Memory Key
- Cooling Shroud
- Integrated Storage Controller Card
- System Memory
- Cooling Fans
- iDRAC6 Express Card (Optional)
- iDRAC6 Enterprise Card (Optional)
- VFlash Media (Optional)
- Processor
- Power Supplies
- System Battery
- Control Panel Assembly
- SAS Backplane
- Power Distribution Board
- System Board
- Troubleshooting Your System
- Safety First-For You and Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting the Video Subsystem
- Troubleshooting a USB Device
- Troubleshooting a Serial I/O Device
- Troubleshooting a NIC
- Troubleshooting a Wet System
- Troubleshooting a Damaged System
- Troubleshooting the System Battery
- Troubleshooting Power Supply
- Troubleshooting System Cooling Problems
- Troubleshooting a Fan
- Troubleshooting System Memory
- Troubleshooting an Internal USB Key
- Troubleshooting an Optical Drive
- Troubleshooting a Tape Backup Unit
- Troubleshooting a Hard Drive
- Troubleshooting an Expansion Card
- Troubleshooting the Processor
- Running the System Diagnostics
- Jumpers and Connectors
- Getting Help
- Index
112 Installing System Components
7
Close the system. See "Closing the System" on page 79.
8
Reconnect the system and peripherals to their power sources, and turn them
on.
Cooling Fans
Your system contains five single-motor fans and provides cooling for the
processor, expansion card, power supplies, and memory modules.
NOTE: Hot-swap removal or installation of the fans is not supported.
NOTE: In the event of a problem with a particular fan, the fan number is referenced
by the system’s management software, allowing you to easily identify and replace
the proper fan by noting the fan numbers on the fan assembly.
Removing a Cooling Fan
WARNING: The cooling fan can continue to spin for some time after the system
has been powered down. Allow time for the fan to stop spinning before removing it
from the system.
WARNING: Do not attempt to operate the system without the cooling fan.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
NOTE: The procedure for removing each individual fan module is the same.
1
Turn off the system, including any attached peripherals, and disconnect
the system from its electrical outlet.
2
Open the system. See "Opening the System" on page 78.
3
Remove the cooling shroud or power distribution board shroud as
applicable. See "Cooling Shroud" on page 101.
4
Disconnect the fan’s power cable from the system board. See Figure 3-16.
5
Grasp the fan and slide it away from the fan assembly. See Figure 3-16.
R310HOM.book Page 112 Thursday, March 4, 2010 1:03 AM