Quick Reference Guide
Table Of Contents
- 6741Utopcover
- 6741Ubk0toc
- 6741Uc10
- 6741Uc20
- 6741Uc30
- 6741Uc40
- 6741Uc50
- 6741Uc60
- 6741Uc70
- Contents
- Checking Inside the Computer
- Safety First—For You and Your Computer
- Opening the Computer Doors
- Removing the Optional Front Bezel
- Removing and Replacing the Expansion- Card Cage
- Removing the Expansion-Card Cage
- Replacing the Expansion-Card Cage
- Inside the Chassis
- Troubleshooting a Wet Computer
- Troubleshooting a Damaged Computer
- Troubleshooting the Battery
- Troubleshooting Redundant Power Supplies
- Removing and Replacing a Power Supply
- Troubleshooting a Cooling Fan
- Troubleshooting Expansion Cards
- Troubleshooting System Memory
- Troubleshooting the Video Subsystem
- Troubleshooting the System Board
- Troubleshooting the Diskette Drive Subsystem
- Troubleshooting a SCSI Tape Drive
- Troubleshooting SCSI Hard-Disk Drives
- Troubleshooting a RAID Controller
- Troubleshooting an Integrated RAID Controller
- Troubleshooting a PERC 2 Card
- 6741Uc80
- Contents
- Installing System Board Options
- Expansion Cards
- Installing an Expansion Card
- Removing an Expansion Card
- Adding Memory
- Memory Upgrade Kits
- DIMM Installation Guidelines
- Performing a Memory Upgrade
- Installing DIMMs
- Removing DIMMs
- Upgrading the Microprocessor or Installing a Secondary Microprocessor
- Removing a Terminator Card
- Installing a Terminator Card
- Removing the SEC Cartridge and Heat Sink Assembly
- Replacing the SEC Cartridge and Heat Sink Assembly
- Activating the Integrated RAID Controller
- Replacing the Battery
- 6741Uc90
- 6741u100
- Contents
- Installing Hard-Disk Drives
- Preparing SCSI Hard-Disk Drives for Installation
- SCSI Hard-Disk Drive Configuration
- Partitioning and Formatting SCSI Hard-Disk Drives
- General Information on Cabling
- Installing SCSI Hard-Disk Drives
- Installing a Dell PowerEdge Expandable RAID Controller Host Adapter Card
- Installing a SCSI Backplane Daughter Card
- Configuring the Boot Device
- 6741u110
- 6741UappendixA
- 6741UsafetyInstructions
- Contents
- Safety Instructions
- Notes, Notices, Cautions, and Warnings
- Safety Caution and Warnings
- Additional Safety Precautions
- General Precautions
- Precautions for Server and Storage Systems
- Precautions for Rack-Mountable Products
- Precautions for Products With Modems, Telecommunications, or Local Area Network Options
- Precautions for Products With Laser Devices
- When Working Inside Your Computer
- Protecting Against Electrostatic Discharge
- Ergonomic Computing Habits
- 6741Upreface
- 6741Ugabbrev
- 6741Ubk0lof
- 6741Ubk0lot
- 6741Ubk0toc
support.dell.com Installing System Board Options 8-9
To remove a DIMM, press down and outward on the ejectors on each end of the
socket until the DIMM pops out of the socket (see Figure 8-6).
()!""
The microprocessor is contained within a single-edge contact (SEC) cartridge and
heat sink assembly. The system board has two guide bracket assemblies, which
hold the SEC cartridge and heat sink assemblies. If your system has only one
microprocessor, the secondary guide bracket assembly connector must contain a ter-
minator card. If you are adding a microprocessor, the secondary microprocessor must
have the same operating frequency as the first. For example, if the system has a
600-MHz primary microprocessor, your secondary microprocessor must also be a
600-MHz microprocessor.
&'(**-++*%
*.,++'*.
,++/%
To remove a terminator card, perform the following steps.
%
!""#$
&'( 0)**(+,*0
*
1. Open the computer doors.
DIMM socket ejectors (2)