Quick Reference Guide
Table Of Contents
- 6741Utopcover
- 6741Ubk0toc
- 6741Uc10
- 6741Uc20
- 6741Uc30
- 6741Uc40
- 6741Uc50
- 6741Uc60
- 6741Uc70
- Contents
- Checking Inside the Computer
- Safety First—For You and Your Computer
- Opening the Computer Doors
- Removing the Optional Front Bezel
- Removing and Replacing the Expansion- Card Cage
- Removing the Expansion-Card Cage
- Replacing the Expansion-Card Cage
- Inside the Chassis
- Troubleshooting a Wet Computer
- Troubleshooting a Damaged Computer
- Troubleshooting the Battery
- Troubleshooting Redundant Power Supplies
- Removing and Replacing a Power Supply
- Troubleshooting a Cooling Fan
- Troubleshooting Expansion Cards
- Troubleshooting System Memory
- Troubleshooting the Video Subsystem
- Troubleshooting the System Board
- Troubleshooting the Diskette Drive Subsystem
- Troubleshooting a SCSI Tape Drive
- Troubleshooting SCSI Hard-Disk Drives
- Troubleshooting a RAID Controller
- Troubleshooting an Integrated RAID Controller
- Troubleshooting a PERC 2 Card
- 6741Uc80
- Contents
- Installing System Board Options
- Expansion Cards
- Installing an Expansion Card
- Removing an Expansion Card
- Adding Memory
- Memory Upgrade Kits
- DIMM Installation Guidelines
- Performing a Memory Upgrade
- Installing DIMMs
- Removing DIMMs
- Upgrading the Microprocessor or Installing a Secondary Microprocessor
- Removing a Terminator Card
- Installing a Terminator Card
- Removing the SEC Cartridge and Heat Sink Assembly
- Replacing the SEC Cartridge and Heat Sink Assembly
- Activating the Integrated RAID Controller
- Replacing the Battery
- 6741Uc90
- 6741u100
- Contents
- Installing Hard-Disk Drives
- Preparing SCSI Hard-Disk Drives for Installation
- SCSI Hard-Disk Drive Configuration
- Partitioning and Formatting SCSI Hard-Disk Drives
- General Information on Cabling
- Installing SCSI Hard-Disk Drives
- Installing a Dell PowerEdge Expandable RAID Controller Host Adapter Card
- Installing a SCSI Backplane Daughter Card
- Configuring the Boot Device
- 6741u110
- 6741UappendixA
- 6741UsafetyInstructions
- Contents
- Safety Instructions
- Notes, Notices, Cautions, and Warnings
- Safety Caution and Warnings
- Additional Safety Precautions
- General Precautions
- Precautions for Server and Storage Systems
- Precautions for Rack-Mountable Products
- Precautions for Products With Modems, Telecommunications, or Local Area Network Options
- Precautions for Products With Laser Devices
- When Working Inside Your Computer
- Protecting Against Electrostatic Discharge
- Ergonomic Computing Habits
- 6741Upreface
- 6741Ugabbrev
- 6741Ubk0lof
- 6741Ubk0lot
- 6741Ubk0toc

support.dell.com Installing System Board Options 8-5
To remove an expansion card, perform the following steps.
%
!""#$
1. Turn off the system, including any attached peripherals, and disconnect the sys-
tem from the electrical outlet.
2. Open the computer doors.
3. Disconnect any cables connected to the card.
4. Remove the expansion-card cage as instructed in “Removing the Expansion-Card
Cage” in Chapter 7.
5. Position the expansion-card cage so that the riser board lies horizontally on your
work surface.
6. To release the expansion card from the card cage, rotate the latch away from the
expansion-card bracket.
7. If the expansion card is a full-length card, release the card's inner end by opening
the tab on the card guide (see Figure 8-3).
8. Grasp the expansion card by its top corners, and carefully remove it from the
expansion-card connector.
9. If you are removing the card permanently, install a metal filler bracket over the
empty card-slot opening.
NOTE: Installing a filler bracket over an empty expansion slot is necessary to
maintain Federal Communications Commission (FCC) certification of the system.
The brackets also keep dust and dirt out of the computer and aid in proper cooling
and airflow inside the computer.
10. Replace the expansion-card cage in the chassis as instructed in “Replacing the
Expansion-Card Cage” in Chapter 7.
11. Close the computer doors, and then reconnect the computer and peripherals to
their AC power sources and turn them on.
The four dual in-line memory module (DIMM) sockets on the system board can
accommodate 64 megabytes (MB) to 2 gigabyte (GB) of registered synchronous
dynamic random-access memory (SDRAM). The DIMM sockets are located near the
front edge of the system board (see Figure 8-1), next to the cooling fan assembly.










