Quick Reference Guide
Table Of Contents
- 6741Utopcover
- 6741Ubk0toc
- 6741Uc10
- 6741Uc20
- 6741Uc30
- 6741Uc40
- 6741Uc50
- 6741Uc60
- 6741Uc70
- Contents
- Checking Inside the Computer
- Safety First—For You and Your Computer
- Opening the Computer Doors
- Removing the Optional Front Bezel
- Removing and Replacing the Expansion- Card Cage
- Removing the Expansion-Card Cage
- Replacing the Expansion-Card Cage
- Inside the Chassis
- Troubleshooting a Wet Computer
- Troubleshooting a Damaged Computer
- Troubleshooting the Battery
- Troubleshooting Redundant Power Supplies
- Removing and Replacing a Power Supply
- Troubleshooting a Cooling Fan
- Troubleshooting Expansion Cards
- Troubleshooting System Memory
- Troubleshooting the Video Subsystem
- Troubleshooting the System Board
- Troubleshooting the Diskette Drive Subsystem
- Troubleshooting a SCSI Tape Drive
- Troubleshooting SCSI Hard-Disk Drives
- Troubleshooting a RAID Controller
- Troubleshooting an Integrated RAID Controller
- Troubleshooting a PERC 2 Card
- 6741Uc80
- Contents
- Installing System Board Options
- Expansion Cards
- Installing an Expansion Card
- Removing an Expansion Card
- Adding Memory
- Memory Upgrade Kits
- DIMM Installation Guidelines
- Performing a Memory Upgrade
- Installing DIMMs
- Removing DIMMs
- Upgrading the Microprocessor or Installing a Secondary Microprocessor
- Removing a Terminator Card
- Installing a Terminator Card
- Removing the SEC Cartridge and Heat Sink Assembly
- Replacing the SEC Cartridge and Heat Sink Assembly
- Activating the Integrated RAID Controller
- Replacing the Battery
- 6741Uc90
- 6741u100
- Contents
- Installing Hard-Disk Drives
- Preparing SCSI Hard-Disk Drives for Installation
- SCSI Hard-Disk Drive Configuration
- Partitioning and Formatting SCSI Hard-Disk Drives
- General Information on Cabling
- Installing SCSI Hard-Disk Drives
- Installing a Dell PowerEdge Expandable RAID Controller Host Adapter Card
- Installing a SCSI Backplane Daughter Card
- Configuring the Boot Device
- 6741u110
- 6741UappendixA
- 6741UsafetyInstructions
- Contents
- Safety Instructions
- Notes, Notices, Cautions, and Warnings
- Safety Caution and Warnings
- Additional Safety Precautions
- General Precautions
- Precautions for Server and Storage Systems
- Precautions for Rack-Mountable Products
- Precautions for Products With Modems, Telecommunications, or Local Area Network Options
- Precautions for Products With Laser Devices
- When Working Inside Your Computer
- Protecting Against Electrostatic Discharge
- Ergonomic Computing Habits
- 6741Upreface
- 6741Ugabbrev
- 6741Ubk0lof
- 6741Ubk0lot
- 6741Ubk0toc
A-6 Dell PowerEdge 2450 Systems Installation and Troubleshooting Guide
Figure A-3 shows the connectors and sockets located on the interposer board.
!
! "
The computer's software security features include a system password and a setup
password, which are discussed in detail in Chapter 4, “Using the System Setup Pro-
gram,” in the
User's Guide
. A password jumper on the system board enables these
password features or disables them and clears any password(s) currently in use.
To disable a forgotten system password or setup password, perform the following
steps.
"#$%!&#
1. Remove the right-side computer cover.
2. Refer to Figure A-1 for the location of the password jumper (labeled “PASSWD”)
on the system board.
3. Remove the jumper plug from the PASSWD jumper.
4. Replace the right-side computer cover, and then reconnect the computer to an
electrical outlet and turn it on.
The existing passwords are not disabled (erased) until the system boots with the
PASSWD jumper plug removed. However, before you assign a new system and/
or setup password, you must install the jumper plug.
NOTE: If you assign a new system and/or setup password with the jumper plug
still removed, the system disables the new password(s) the next time it boots.
system board
interface cable
connector (P1)
interposer board
power cable
connector (P3)
cooling fans
wiring harness
connector (P2)
control panel cable connector
diskette drive/CD-ROM drive interface connector