Release Notes
Table Of Contents
- Dell EMC Z9100–ON System Release Notes, OS Version 9.14(2.9P1)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.9) Features
- Restrictions
- Documentation Corrections
- Changes to the Default Behavior and CLI Syntax
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the sub-components
- Upgrading the ONIE Package for the Z9100-ON System
- Upgrading the DIAG Package for the Z9100-ON System
- Installing Dell EMC Networking OS on the Z9100-ON using ONIE
- Upgrading the Z9100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Uninstalling the Dell EMC Networking operating system
- Installing a Third Party Operating System
- Support Resources
Enter the following command to upgrade DIAG on the Z9100–ON system: onie-nos-install ftp://ftp:ftp@<ftp-
server-adress>/tftpboot/diag-installer-x86_64–z9100_c2538-r0.bin
NOTE: You must copy the diag-installer-x86_64–z9100_c2538-r0.bin file to the /tftpboot folder in the
server.
The DIAG is updated on the system, as shown:
ONIE:/ # onie-nos-install ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-
z9100_c2538-r0.bin
discover: installer mode detected.
Stopping: discover... done.
Info: Fetching ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-z9100_c2538-
r0.bin ...
Connecting to 10.11.227.233 (10.11.227.233:21)
installer 100% |*******************************| 167M 0:00:00 ETA
ONIE: Executing installer: ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-
z9100_c2538-r0.bin
Ignoring Verifying image checksum ... OK.
cur_dir / archive_path /installer tmp_dir /tmp/tmp.nC1CKc
Preparing image archive ...sed -e '1,/^exit_marker$/d' /installer | tar xf - OK.
DiagOS Installer: platform: x86_64_z9100_c2538-r0
EDA-DIAG Partiton not found.
Diag OS Installer Mode : INSTALL
INSTALL mode : would remove existing partitions and create fresh...
Creating new diag-os partition /dev/sda3 with label EDA-DIAG ...
Warning: The kernel is still using the old partition table.
The new table will be used at the next reboot.
The operation has completed successfully.
volume label EDA-DIAG on device /dev/sda3
mke2fs 1.42.8 (15-Dec-2020)
Filesystem label=EDA-DIAG
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
65536 inodes, 262144 blocks
13107 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=268435456
8 block groups
Installing Dell EMC Networking OS on the Z9100-ON
using ONIE
NOTE:
You will need the Dell Networking OS installer package, ONIE-FTOS-Z9100-ON-9.14.2.9.bin to install the Dell
EMC Networking OS on your Z9100-ON system that has only ONIE.
To install the Dell EMC Networking OS version 9.14(2.9) on a new Z9100-ON device, perform the following steps:
1. Reboot the system. During the reboot process, the system displays the following message prompting you to press the Esc
key in order to stop the auto-boot process:
Press Esc to stop autoboot ... 5
Grub 1.99~rc1 (Dell EMC Inc)
Built by build at bsdlab on Tue_Dec_15_07:12:52_UTC_2020
Z9100 Boot Flash Label 3.23.2.13 NetBoot Label 3.23.2.13
2. At this prompt message, press the Esc key. The following menu appears:
GNU GRUB version 1.99~rc1
+----------------------------------------------+
21