Release Notes
Table Of Contents
- Dell EMC Z9100–ON System Release Notes, OS Version 9.14(2.9P1)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.9) Features
- Restrictions
- Documentation Corrections
- Changes to the Default Behavior and CLI Syntax
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the sub-components
- Upgrading the ONIE Package for the Z9100-ON System
- Upgrading the DIAG Package for the Z9100-ON System
- Installing Dell EMC Networking OS on the Z9100-ON using ONIE
- Upgrading the Z9100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Uninstalling the Dell EMC Networking operating system
- Installing a Third Party Operating System
- Support Resources
Restarting system.
machine restart
BIOS (Dell EMC, Inc.) Boot Selector
Z9100 3.23.0.0-9 32 port 100G / 2 port sfp+ mgmt
Booting Primary BIOS
SMF Version 0x12: Last POR=0x11, Reset=0x55
POST Configuration
CPU Signature 406D8
CPU FamilyID=6, Model=4D, SteppingId=8, Processor=0
Microcode Revision 125
Platform ID: 0x10041A57
PMG_CST_CFG_CTL: 0x40006
BBL_CR_CTL3: 0x7E2801FF
Misc EN: 0x840081
Gen PM Con1: 0x203808
Therm Status: 0x88440000
POST Control=0xEA010303, Status=0xE6009F00
BIOS initializations...
CPGC Memtest ................................ PASS
Upgrading the DIAG Package for the Z9100-ON System
To upgrade the DIAG package, use one of the following two processes:
● Zero touch (dynamic): Copy the update ONIE installer for your system to the TFTP/HTTP server. Configure the DHCP
options using the ONIE specifications shown at the following link: https://github.com/opencomputeproject/onie/wiki/
Design-Spec-SW-Updating-ONIE.
● Manual: Copy the image onto the TFTP/HTTP servers and boot ONIE. Update the ONIE using the onie-self-update
command, then download and run an ONIE updater image (diag-installer-x86_64–z9100_c2538–r0.bin). The
supported URL types are: HTTP, FTP, TFTP, and FILE.
NOTE:
If Dell EMC Networking OS is already installed on the Z9100-ON system, before upgrading the DIAG package, you
must first uninstall Dell EMC Networking OS. For more information on uninstalling Dell EMC Networking OS, see Uninstalling
Dell EMC Networking OS on the Z9100-ON.
To upgrade DIAG, perform the following steps:
1. Reboot the system. During the reboot process, the system displays the following message prompting you to press the Esc
key in order to stop the auto-boot process:
Press Esc to stop autoboot ... 5
Grub 1.99~rc1 (Dell EMC)
Built by build at bsdlab on Tue_Dec_15_07:12:52_UTC_2020
Z9100 Boot Flash Label 3.23.2.13 NetBoot Label 3.23.2.13
2. At this prompt message, press the Esc key. The following menu appears:
GNU GRUB version 1.99~rc1
+----------------------------------------------+
|Dell EMC NEtworking OS |
|Dell EMC-Boot Line Interface |
|DIAG-OS |
|ONIE |
| |
+----------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, 'f' to boot FTOS, 'b' to go to
BLI, 'o' to boot ONIE, 'd' to boot DIAG-OS, 'e' to edit the commands
before booting or 'c' for a command-line.
19