Deployment Guide

In S6000, any pfc-dot1p priorities configured on a given interface need not be the same across the system. In other words,
lossless queue limit is applicable on a per-port level and not on the global-config context. For example, one of the interfaces can
have pfc-dot1p priorities as 2 and 3. Whereas, the other interface(s) can have its pfc-dot1p priorities as 4 and 5.
It is the user responsibility to have symmetric PFC configurations on the interfaces involved in a particular PFC-enabled
traffic-flow to obtain lossless behavior.
Configuring PFC in a DCB Map
A switch supports the use of a DCB map in which you configure priority-based flow control (PFC) setting. To configure PFC
parameters, you must apply a DCB map on an interface.
PFC Configuration Notes
PFC provides flow control based on the 802.1p priorities in a converged Ethernet traffic that is received on an interface and
is enabled by default when you enable DCB. As an enhancement to the existing Ethernet pause functionality, PFC stops traffic
transmission for specified priorities (CoS values) without impacting other priority classes. Different traffic types are assigned to
different priority classes.
When traffic congestion occurs, PFC sends a pause frame to a peer device with the CoS priority values of the traffic that
needs to be stopped. DCBx provides the link-level exchange of PFC parameters between peer devices. PFC allows network
administrators to create zero-loss links for SAN traffic that requires no-drop service, while at the same time retaining packet-
drop congestion management for LAN traffic.
On a switch, PFC is enabled by default on Ethernet ports (pfc mode on command). You can configure PFC parameters
using a DCB map or the pfc priority command in Interface configuration mode. For more information, see Configuring
Priority-Based Flow Control.
As soon as you apply a DCB map with PFC enabled on an interface, DCBx starts exchanging information with a peer. The
IEEE802.1Qbb, CEE and CIN versions of PFC TLV are supported. DCBx also validates PFC configurations that are received
in TLVs from peer devices. By applying a DCB map with PFC enabled, you enable PFC operations on ingress port traffic. To
achieve complete lossless handling of traffic, configure PFC priorities on all DCB egress ports.
When you apply or remove a DCB input policy from an interface, one or two CRC errors are expected to be noticed on the
ingress ports for each removal or attachment of the policy. This behavior occurs because the port is brought down when PFC
is configured. When a DCB input policy with PFC profile is configured or unconfigured on an interface or a range of interfaces
not receiving any traffic, interfaces with PFC settings that receive appropriate PFC-enabled traffic (unicast, mixed-frame-size
traffic) display incremental values in the CRC and discards counters. (These ingress interfaces receiving pfc-enabled traffic
have an egress interface that has a compatible PFC configuration).
NOTE: DCB maps are supported only on physical Ethernet interfaces.
● To remove a DCB map, including the PFC configuration it contains, use the no dcb map command in Interface
configuration mode.
● To disable PFC operation on an interface, use the no pfc mode on command in DCB-Map configuration mode.
● Traffic may be interrupted when you reconfigure PFC no-drop priorities in a DCB map or re-apply the DCB map to an
interface.
● For PFC to be applied, the configured priority traffic must be supported by a PFC peer (as detected by DCBx).
● If you apply a DCB map with PFC disabled (pfc off), you can enable link-level flow control on the interface using
the flowcontrol rx on tx on command. To delete the DCB map, first disable link-level flow control. PFC is then
automatically enabled on the interface because an interface is PFC-enabled by default.
● To ensure no-drop handling of lossless traffic, PFC allows you to configure lossless queues on a port (see Configuring
Lossless Queues).
● When you configure a DCB map, an error message is displayed if the PFC dot1p priorities result in more than two lossless
queues.
● When you apply a DCB map, an error message is displayed if link-level flow control is already enabled on an interface. You
cannot enable PFC and link-level flow control at the same time on an interface.
● In a switch stack, configure all stacked ports with the same PFC configuration.
Data Center Bridging (DCB)
245