API Guide

Advertising the Extended Power through MDI
The power device sends the following information in the LLDP-MED extended power-via-MDI TLV.
1. Power Requirement: Dell Networking OS uses it for power allocation
2. Power Priority — Critical, High, or Low: Dell Networking OS uses it for power priority calculation.
3. External Power Source: Dell Networking OS does not use this information. IEEE 802.3at power-via-mdi TLV
To configure the system or an interface to advertise IEEE 802.1ab extended power-via-mdi TLV, use the advertise med power-
via-mdi command.
When you enable the advertise med power-via-mdi command in CONFIGURATION mode, advertisement is enabled for all the
interfaces. To enable advertisement for a specific interface, use INTERFACE Configuration mode.
NOTE: If you also configure LLDP to use the 802.3 TLV format, 802.3 overrides the advertise med power-via-mdi
settings. For more information, see Advertising Extended Power Though dot3–TLVs.
Parameters
power-via-mdi — Enter the keyword power-via-mdi to advertise IEEE 802.1ab MED Extended power-via-mdi TLV.
• Configure the system or an interface to advertise IEEE 802.1ab extended power-via-mdi TLV.
LLDP CONFIGURATION or INTERFACE LLDP CONFIGURATION mode
advertise med power-via-mdi
Example of Advertising the Extender Power through MDI TLVs in LLDP Configuration Mode
The following example configures all the interfaces to advertise IEEE 802.1ab power through MDI.
Dell(conf-lldp)#advertise med power-via-mdi
Example of Advertising the Extender Power through MDI TLVs in Interface LLDP Configuration Mode
The following example configures interface peGigE 0/0/1 to advertise IEEE 802.1ab power through MDI.
Dell(conf)#interface peGigE 0/0/1
Dell(conf-if-pegi-0/0/1)#protocol lldp
Dell(conf-if-pegi-0/0/1-lldp)#advertise med power-via-mdi
Advertising Extended Power Though dot3–TLVs
The power device sends the following information in the IEEE 802.3 power-via-mdi TLV.
1. Power Class — Dell Networking OS honors and displays the power class in the show power inline command in EXEC mode
(the PD-requested power value must be within the class max watts limit).
2. Type — Dell Networking OS uses type only when the type is Type1 or Type2 PD and displays the type in the show power
inline command in EXEC mode. The Dell Networking OS does not use Type1 or Type2 PSE requests.
3. Priority — Dell Networking OS uses priority for priority calculation.
4. PD requested power value — Dell Networking OS uses this value for power allocation.
5. PSE allocated power value — Dell Networking OS uses this value to check whether the PD is in sync with the PSE.
To enable the system or interface to advertise IEEE 802.3 power-via-mdi TLV to advertise its power negotiation capabilities with the
powered devices using LLDP, use the advertise dot3–tlv power—via—mdi command. You can configure this command either on
a specific interface or globally. This command provides advanced power management between LLDP-MED endpoints and network
connected devices. It allows an endpoint to communicate more precise required power requirements and enables the port extender to
allocate less power to the endpoint, while making more power available to other port extender ports.
By default, advertising extended power through dot3–TVLs is disabled.
NOTE:
The port extender performs Layer 2 classification and participates in LLDP power negotiation only when in Class
mode. To use this feature, configure PoE in power management Class mode. For information about Class mode, see
Enabling PoE/PoE+ on a Port.
• Configure the system or an interface to advertise IEEE 802.3 power-via-mdi TLV to advertise its power negotiation capabilities with
the powered devices using LLDP.
LLDP CONFIGURATION or INTERFACE LLDP CONFIGURATION mode
728
Power over Ethernet (PoE)