Release Notes
Table Of Contents
- Dell EMC S5048F–ON System Release Notes, OS Version 9.14(2.10)
- Document Revision History
- Requirements
- New Dell EMC Networking OS Version 9.14(2.10) Features
- Restrictions
- Changes to Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S5048F-ON System
- Upgrading the DIAG Package for the S5048F-ON System
- Installing Dell EMC Networking OS on the S5048F-ON using ONIE
- Upgrading the CPLD
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA
- Upgrading the S5048F-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Support Resources
random: nonblocking pool is initialized
ONIE: Using link-local IPv4 addr: eth0: 169.254.47.74/16
Starting: dropbear ssh daemon... done.
Starting: telnetd... done.
discover: installer mode detected. Running installer.
Starting: discover... done.
Please press Enter to activate this console. Info: eth0: Checking link... up.
Info: Trying DHCPv4 on interface: eth0
To check the install status inspect /var/log/onie.log.
Try this: tail -f /var/log/onie.log
** Installer Mode Enabled **
ONIE:/ #
ONIE:/ # Warning: Unable to configure interface using DHCPv4: eth0
ONIE: Using link-local IPv4 addr: eth0: 169.254.168.149/16
5. At the ONIE prompt, to stop the ONIE discovery process, enter the following command:
ONIE:/ # onie-discovery-stop
The ONIE discovery stops, as shown:
ONIE:/ # onie-discovery-stop
discover: installer mode detected.
Stopping: discover... done.
ONIE:/ #
6. Configure an interface and assign an IP address to that interface using the following command:
ONIE:/ # ifconfig eth0 10.16.129.131/16
7. Enter the following command to begin the installation process:
ONIE:/ # onie-nos-install tftp://<tftp-server-address>/ONIE-FTOS-S5048F-
ON-9.14.2.10.bin
NOTE: You must copy the ONIE-FTOS-S5048F-ON-9.14.2.10.bin file to the /tftpboot folder in the server.
NOTE: After the Dell EMC Networking OS installation completes, the system automatically reboots.
Following is the installation and boot log of Dell EMC Networking OS:
ONIE:/ # onie-nos-install tftp://10.16.127.6/users/admin/ONIE-FTOS-S5048F-O
N-9.14.2.10.bin
discover: installer mode detected.
Stopping: discover... done.
Info: Fetching tftp://10.16.127.6/users/admin/ONIE-FTOS-S5048F-ON-9.14.2.10.bin ...
users/admin/ONI 100% |*******************************| 96983k 0:00:00 ETA
ONIE: Executing installer: tftp://10.16.127.6/users/admin/ONIE-FTOS-S5048F-
ON-9.14.2.10.bin
Verifying image checksum ... OK.
Preparing image archive from /installer ... Done.
Verifying Product Platform...
Product Name : S5048FON
Image Platform : FTOS-S5048F-ON
Image File : FTOS-S5048F-ON-9.14.2.10.bin
Image Compatibility : Verified
Verifying MAC Address...
MAC Address is Configured
Image Platform : FTOS-S5048F-ON
Deleting Extra partitions... Done.
Creating New partitions... Done.
Creating Hybrid MBR... Done.
Mouting /dev/sda4,/dev/sda5 and /dev/sda6... mkfs.fat 3.0.26 (2021-05-18)
mkfs.fat 3.0.26 (2021-05-18)
mkfs.fat 3.0.26 (2021-05-18)
mkfs.fat 3.0.26 (2021-05-18)
mkfs.fat 3.0.26 (2021-05-18)
15