Release Notes
Table Of Contents
- Dell S6100–ON System Release Notes, OS Version 9.14(2.9P1)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.9) Features
- Restrictions
- Changes to the Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6100-ON System
- Upgrading the DIAG Package for the S6100-ON System
- Installing Dell EMC Networking OS on the S6100-ON using ONIE
- Upgrading the S6100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Upgrade the CPLD Images
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA Image
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Contacting Dell EMC
Platform Version Size ReleaseTime
S-Series:S6100-ON 9.14(2.9) 78345374 Dec 15 2020 17:15:23
TARGET IMAGE INFORMATION :
---------------------------------------------------------------------
Type Version Target checksum
runtime 9.14(2.9) Control Processor passed
BOOT IMAGE INFORMATION :
---------------------------------------------------------------------
Type Version Target checksum
boot flash 3.25.2.14 Control Processor passed
BOOTSEL IMAGE INFORMATION :
---------------------------------------------------------------------
Type Version Target checksum
boot selector 3.25.0.0-6 Control Processor passed
FPGA IMAGE INFORMATION :
---------------------------------------------------------------------
Card FPGA Name Version
stack-unit 1 S6100-ON SWITCHCARD CPLD 5
stack-unit 1 S6100-ON IOM CPLD1 5
stack-unit 1 S6100-ON IOM CPLD2 12
stack-unit 1 : --- NO IOM CPLD3 FOUND --- 5
stack-unit 1 S6100-ON IOM CPLD4 4
stack-unit 1 S6100-ON MSS FPGA 1.1
stack-unit 1 S6100-ON MSS IAP 2.4
stack-unit 1 S6100-ON OOB-FPGA 1.0
Upgrading the Switchcard-CPLD Image
The S6100-ON system with Dell EMC Networking OS Version 9.14(2.9) requires switchcard-cpld image 5.
NOTE:
The upgrade fpga-image switchcard-cpld stack-unit 1 booted command is hidden when using the
feature in the CLI. However, it is a supported command. The mod-id option represents the ID of the module slot on the
S6100–ON.
NOTE: Ensure that the BIOS version is 3.25.0.0-6. You can verify this version using the show system stack-unit 1
command.
To upgrade the CPLD image, follow these steps.
1. Upgrade the switchcard-CPLD image.
EXEC Privilege Mode
upgrade fpga-image switchcard-cpld stack-unit <1> booted
Current information for the system:
========================================================================
Card Device Name Current Version New Version
------------------------------------------------------------------------
Unit1 S6100-ON SWITCHCARD CPLD 4 5
***********************************************************************
* Warning - Upgrading FPGA is inherently risky and should *
* only be attempted when necessary. A failure at this upgrade may *
* cause a board RMA. Proceed with caution ! *
***********************************************************************
Upgrade image for stack-unit 1 [yes/no]: yes
Cpld upgrade in progress!!! Please do NOT power off the unit!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Upgrade result :
================
Unit 1 Cpld upgrade successful Unit 1. Please power cycle to take effect.
21