Release Notes
Table Of Contents
- Dell EMC System S6010–ON 9.14(2.9P1) Release Notes
- Document Revision History
- Supported Hardware
- Supported Software
- New Dell Networking OS Version 9.14(2.9) Features
- Restrictions
- Changes to Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6010-ON System
- Upgrading the DIAG Package for the S6010-ON System
- Installing Dell EMC Networking OS on the S6010-ON using ONIE
- Upgrade the S6010-ON Dell EMC Networking OS Image and Boot Code using Dell EMC Networking OS CLI
- Upgrading the CPLD
- Uninstalling Dell EMC Networking OS from the S6010-ON
- Support Resources
ONIE is updated on the system, as shown:
discover: ONIE update mode detected.
Stopping: discover... done.
Info: Fetching tftp://10.16.127.35/onie-updater-x86_64-s6010_c2538-r0 ...
onie-updater-x86_64- 100% |*******************************| 16881k 0:00:00 ETA
ONIE: Executing installer: tftp://10.16.127.35/onie-updater-x86_64-s6010_c2538-r0
Verifying image checksum ... OK.
Preparing image archive ... OK.
ONIE: Version : 3.26.1.0-3
ONIE: Architecture : x86_64
ONIE: Machine : s6010_c2538
ONIE: Machine Rev : 0
ONIE: Config Version: 1
Installing ONIE on: /dev/sda
Rebooting...
ONIE:/ # discover: ONIE update mode detected.
Stopping: discover...start-stop-daemon: warning: killing process 541: No such process
done.
Stopping: dropbear ssh daemon... done.
Stopping: telnetd... done.
Stopping: syslogd... done.
Info: Unmounting kernel filesystems
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL tosd 4:0:0:0: [sda] Synchronizing SCSI cache
Restarting system.
machine restart
BIOS (Dell EMC, Inc.) Boot Selector
S6010 3.26.0.0-4
32 port 40G QSFP
POST Configuration
CPU Signature 406D8
CPU FamilyID=6, Model=4D, SteppingId=8, Processor=0
Microcode Revision 125
Platform ID: 0x10041A48
PMG_CST_CFG_CTL: 0x40006
BBL_CR_CTL3: 0x7E2801FF
Misc EN: 0x840081
Gen PM Con1: 0x203808
Therm Status: 0x884E0000
POST Control=0xEA000303, Status=0xE6009F00
BIOS initializations...
CPGC Memtest ................................ PASS
Upgrading the DIAG Package for the S6010-ON System
To upgrade the DIAG package, use one of the following two processes:
● Zero touch (dynamic): Copy the update ONIE installer for your system to the TFTP/HTTP server. Configure the DHCP
options using the ONIE specifications shown at the following link: https://github.com/opencomputeproject/onie/wiki/
Design-Spec-SW-Updating-ONIE.
● Manual: Copy the image onto the TFTP/HTTP servers and boot ONIE. Update the ONIE using the onie-self-update
command, then download and run an ONIE updater image (diag-installer-x86_64-s6010_c 2538-r0.bin). The
supported URL types are: HTTP, FTP, TFTP, and FILE.
To upgrade DIAG, perform the following steps:
9