Release Notes
Table Of Contents
- Dell EMC System S6010–ON 9.14(2.9P1) Release Notes
- Document Revision History
- Supported Hardware
- Supported Software
- New Dell Networking OS Version 9.14(2.9) Features
- Restrictions
- Changes to Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6010-ON System
- Upgrading the DIAG Package for the S6010-ON System
- Installing Dell EMC Networking OS on the S6010-ON using ONIE
- Upgrade the S6010-ON Dell EMC Networking OS Image and Boot Code using Dell EMC Networking OS CLI
- Upgrading the CPLD
- Uninstalling Dell EMC Networking OS from the S6010-ON
- Support Resources
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/
sda,gpt7,bsd4).
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/
sda,gpt7,bsd12).
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/
sda,gpt7,bsd4).
grub-install: warning: Discarding improperly nested partition (hostdisk//dev/
sda,gpt7,bsd12).
Installation finished. No error reported.
discover: installer mode detected. Running installer.
Starting: discover... done.
Please press Enter to activate this console. To check the install status inspect
/var/log/onie.log.
Try this: tail -f /var/log/onie.log
** Installer Mode Enabled **
ONIE:/ #
ONIE:/ #
5. At the ONIE prompt, to stop the ONIE discovery process, enter the following command:
ONIE:/ # onie-discovery-stop
The ONIE discovery stops, as shown:
ONIE:/ # onie-discovery-stop
discover: installer mode detected.
Stopping: discover... done.
ONIE:/ #
6. Configure an interface and assign an IP address to that interface using the following command:
ONIE:/ # ifconfig eth0 10.16.133.213/16
7. Enter the following command to begin the installation process:
ONIE:/ # onie-nos-install tftp://<tftp-server-address>/ONIE-FTOS-S6010-9.14.2.9.bin
NOTE: You must copy the ONIE-FTOS-S6010-9.14.2.9.bin file to the /tftpboot folder in the server.
NOTE: After the Dell EMC Networking OS installation completes, the system automatically reboots.
Following is the installation and boot log of Dell EMC Networking OS:
ONIE:/ # onie-nos-install tftp://10.16.127.35/ONIE-FTOS-S6010-9.14.2.9.bin
discover: installer mode detected.
Stopping: discover... done.
Info: Fetching tftp://10.16.127.35/ONIE-FTOS-S6010-9.14.2.9.bin ...
ONIE-FTOS-S6010-9-14 100% |*******************************| 105M 0:00:00 ETA
ONIE: Executing installer: tftp://10.16.127.35/ONIE-FTOS-S6010-9.14.2.9.bin
Verifying image checksum ... OK.
Preparing image archive from /var/tmp/installer ... Done.
Verifying Product Platform...
Product Name : S6010-ON
Image Platform : FTOS-S6010
Image File : FTOS-S6010-9.14.2.9.bin
Image Compatibility : Verified
Verifying MAC Address...
MAC Address is Configured
Image Platform : FTOS-S6010
Deleting Extra partitions... Done.
Creating New partitions... Done.
Creating Hybrid MBR... Done.
Mouting /dev/sda4,/dev/sda5 and /dev/sda6... mkfs.fat 3.0.26 (2020-12-15)
mkfs.fat 3.0.26 (2020-12-15)
mkfs.fat 3.0.26 (2020-12-15)
mkfs.fat 3.0.26 (2020-12-15)
Done.
Installing GRUB on /dev/sda4...Done.
14