Release Notes
Table Of Contents
- Dell EMC S5048F–ON System Release Notes, OS Version 9.14(2.9P1)
- Document Revision History
- Requirements
- New Dell EMC Networking OS Version 9.14(2.9) Features
- Restrictions
- Changes to Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S5048F-ON System
- Upgrading the DIAG Package for the S5048F-ON System
- Installing Dell EMC Networking OS on the S5048F-ON using ONIE
- Upgrading the CPLD
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA
- Upgrading the S5048F-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Support Resources
DellEMC#delete flash://confd_cdb.tar.gz
DellEMC#reload
● The following features are not available in Dell EMC Networking OS:
○ Protocol-independent multicast (PIM) equal cost multi path (ECMP)
○ Static Internet group management protocol (IGMP) join (ip igmp static-group)
○ IGMP querier timeout configuration (ip igmp querier-timeout)
○ IGMP group join limit (ip igmp group join-limit)
● When 1024 or more VNI profiles are configured, the system takes more time to load. Dell EMC recommends to restrict the
VNI profiles to be less than 1000.
● If you use the interface range command to select multiple interfaces that are added to the management VRF, the
ipv6 address command does not display the autoconfig option. You can configure the autoconfig command on
individual interfaces.
● If you use the interface range command to select multiple interfaces that are added to the management VRF, the
ipv6 nd command displays the following options but they do not take effect if you use them:
○ dns-server
○ hop-limit
○ managed-config-flag
○ max-ra-interval
○ mtu
○ other-config-flag
○ prefix
○ ra-guard
○ ra-lifetime
○ reachable-time
○ retrans-timer
○ suppress-ra
● When FRRP is enabled in a VLT domain, no flavor of Spanning tree should concurrently be enabled on the nodes of that
specific VLT domain. In essence FRRP and xSTP should not co-exist in a VLT environment.
● On the device, the 48 SFP28 ports are split into 12 port groups; each group constituting four continuous SFP28 ports. Within
a port group, all four ports can run at 25G/10G/1G speed. The port group speed is determined by the first optic inserted in
any one of the four ports. For example, if you insert an SFP+ in port 1/1, the port group speed is set to 1G/10G. If you insert
a 25G optic in port 1/2, the system displays an error message and does not enable the 25G optic. The port group speed
resets to the default speed of 25G when you remove the SFP+ from port 1/1.
Changes to Default Behavior and CLI Syntax
The following behavior and CLI changes are applicable to the S4048T–ON switch with Dell EMC Networking OS version
9.14(2.9):
None.
Documentation Corrections
This section describes the errors identified in the current release of the Dell EMC Networking OS.
None.
Deferred Issues
Issues that appear in this section were reported in Dell EMC Networking OS version 9.14(2.0) as open, but have since been
deferred. Deferred caveats are those that are found to be invalid, not reproducible, or not scheduled for resolution.
Deferred issues are reported using the following definitions.
4