Release Notes
Table Of Contents
- Dell S6100–ON System Release Notes, OS Version 9.14(2.10)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.10) Features
- Restrictions
- Changes to the Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6100-ON System
- Upgrading the DIAG Package for the S6100-ON System
- Installing Dell EMC Networking OS on the S6100-ON using ONIE
- Upgrading the S6100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Upgrade the CPLD Images
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA Image
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Contacting Dell EMC
DellEMC#May 18 11:28:09: %STKUNIT1-M:CP %DOWNLOAD-6-FPGA_UPGRADE: UNIT 1 fpga upgrade
success.
BIOS (Dell EMC) Boot Selector
S6100 3.25.0.0-6 4 IO card / 2 port sfp+ mgmt.
After the SMF MSS-IAP upgrade is successfully completed, the system re-boots automatically.
Upgrading the SmartFusion Microcontroller Subsystem
— SMF MSS-FPGA
The S6100-ON system with Dell EMC Networking OS Version 9.14(2.10) requires mss-fpga image 1.1.
NOTE: Before upgrading the SmartFusion Microcontroller Subsystem SMF MSS-FPGA, you must first upgrade the SMF
MSS-IAP.
To upgrade the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA, follow these steps:
1. Upgrade the SMF MSS-FPGA image.
EXEC Privilege Mode
upgrade mss-fpga-image stack-unit <stack–unit–id> booted
DellEMC#upgrade mss-fpga-image stack-unit 1 booted
Current information for the system:
========================================================================
Card Device Name Current Version New Version
------------------------------------------------------------------------
CP S6100-ON MSS FPGA 1.1 1.1
***********************************************************************
* Warning - Upgrading FPGA is inherently risky and should *
* only be attempted when necessary. A failure at this upgrade may *
* cause a board RMA. Proceed with caution ! *
***********************************************************************
Upgrade image for stack-unit 1 [yes/no]: yes
SMF FPGA upgrade in progress!!! Please do NOT power off the unit!!! Auto Reset will
happen at the end of Upgrade!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Upgrade result :
================
UNIT1 SMF FPGA upgrade successful UNIT1. will go for reboot to complete the upgrade.
DellEMC#May 18 13:49:27: %STKUNIT1-M:CP %DOWNLOAD-6-FPGA_UPGRADE: UNIT 1 fpga upgrade
success.
BIOS (Dell EMC) Boot Selector
S6100 3.25.0.0-6 4 IO card / 2 port sfp+ mgmt.
NOTE:
Although the system displays that the system power cycles automatically after the upgrade, the system may not
power cycle. If the system does not power cycle automatically, wait for at least five minutes and power cycle the system
by switching off and switching on the system.
Upgrading the OOB-FPGA Image
The S6100-ON system with Dell EMC Networking OS Version 9.14(2.10) requires oob-fpga image 1.0.
To upgrade the OOB-FPGA, follow these steps:
1. Upgrade the OOB-FPGA image.
24