Release Notes
Table Of Contents
- Dell S6100–ON System Release Notes, OS Version 9.14(2.10)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.10) Features
- Restrictions
- Changes to the Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6100-ON System
- Upgrading the DIAG Package for the S6100-ON System
- Installing Dell EMC Networking OS on the S6100-ON using ONIE
- Upgrading the S6100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Upgrade the CPLD Images
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA Image
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Contacting Dell EMC
DellEMC#reload
Proceed with reload [confirm yes/no]: y
8. Verify the S6100–ON has been upgraded to the Dell EMC Networking OS version 9.14(2.10).
EXEC Privilege Mode
show version
DellEMC#show version
Dell EMC Real Time Operating System Software
Dell EMC Operating System Version: 2.0
Dell EMC Application Software Version: 9.14(2.10)
Copyright (c) 1999-2021 by Dell EMC Inc. All Rights Reserved.
Build Time: Tue May 18 00:15:13 2021
Build Path: /build/build08/SW/SRC
Dell EMC Networking OS uptime is 1 minute(s)
System image file is "FTOS-S6100.bin"
System Type: S6100-ON
Control Processor: Intel Rangeley with 3 Gbytes (3203289088 bytes) of memory, core(s)
4.
8G bytes of boot flash memory.
1 4 Modules, 16x40G/8x100G ports TE/TF/FO/FI/HU G (S6100-ON)
14 Ten GigabitEthernet/IEEE 802.3 interface(s)
12 Twenty Five GigabitEthernet/IEEE 802.3 interface(s)
2 Hundred GigabitEthernet/IEEE 802.3 interface(s)
DellEMC#
Upgrade the Boot Selector and Boot Flash Images from
Dell EMC Networking OS
To upgrade the Boot Selector and Boot Flash images from Dell EMC Networking OS, perform the following steps:
1. Upgrade the S6100-ON Boot Selector image.
EXEC Privilege Mode
upgrade boot bootselector-image stack-unit [<id> | all] [booted]
To upgrade the Boot Selector image to the image version packed with the loaded Dell EMC Networking OS image, use the
booted option. You can find the Boot Selector image version packed with the loaded Dell EMC Networking OS using the
show os-version command in EXEC Privilege mode.
DellEMC#upgrade boot bootselector-image stack-unit 1 booted
Current Boot information in the system:
========================================================================
Card BootSelector Current Version New Version
------------------------------------------------------------------------
Unit1 Boot Selector 3.25.0.0-5 3.25.0.0-6
***********************************************************************
* Warning - Upgrading boot selectors is inherently risky and should *
* only be attempted when necessary. A failure at this upgrade may *
* cause a board RMA. Proceed with caution ! *
***********************************************************************
Proceed upgrade Boot Selector image for stack-unit 1 [yes/no]: yes
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Bootselector image upgrade for stack-unit 1 completed successfully.
DellEMC#
2. Reload the unit.
17