Release Notes
Table Of Contents
- Dell S6100–ON System Release Notes, OS Version 9.14(2.10)
- Document Revision History
- Requirements
- New Dell Networking OS Version 9.14(2.10) Features
- Restrictions
- Changes to the Default Behavior and CLI Syntax
- Documentation Corrections
- Deferred Issues
- Fixed Issues
- Known Issues
- Upgrading the ONIE Package for the S6100-ON System
- Upgrading the DIAG Package for the S6100-ON System
- Installing Dell EMC Networking OS on the S6100-ON using ONIE
- Upgrading the S6100-ON Dell EMC Networking OS Image using Dell EMC Networking OS CLI
- Upgrade the Boot Selector and Boot Flash Images from Dell EMC Networking OS
- Upgrade the CPLD Images
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-IAP
- Upgrading the SmartFusion Microcontroller Subsystem — SMF MSS-FPGA
- Upgrading the OOB-FPGA Image
- Uninstalling the Dell EMC Networking OS
- Installing a Third Party Operating System
- Contacting Dell EMC
6. Configure an interface and assign an IP address to that interface using the following command:
ONIE:/ # ifconfig eth0 10.16.129.131/16
7. Enter the following command to upgrade DIAG on the S6100–ON system: onie-nos-install ftp://ftp:ftp@<ftp-
server-adress>/tftpboot/ diag-installer-x86_64-dell_s6100_c2538-r0.3.25.4.1.bin
NOTE: Copy the diag-installer-x86_64-dell_s6100_c2538-r0.3.25.4.1.bin file to the /tftpboot
folder in the server.
The DIAG is updated on the system, as shown:
ONIE:/ # onie-nos-install ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-
dell_s6100_c2538-r0.3.25.4.1.bin
discover: installer mode detected.
Stopping: discover... done.
Info: Fetching ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-
dell_s6100_c2538-r0.3.25.4.1.bin ...
Connecting to 10.11.227.233 (10.11.227.233:21)
installer 100% |*******************************| 167M 0:00:00 ETA
ONIE: Executing installer: ftp://ftp:ftp@10.11.227.233/tftpboot/diag-installer-x86_64-
dell_s6100_c2538-r0.3.25.4.1.bin
Ignoring Verifying image checksum ... OK.
cur_dir / archive_path /installer tmp_dir /tmp/tmp.nC1CKc
Preparing image archive ...sed -e '1,/^exit_marker$/d' /installer | tar xf - OK.
DiagOS Installer: platform: x86_64-dell_S6100_c2538-r0
EDA-DIAG Partiton not found.
Diag OS Installer Mode : INSTALL
INSTALL mode : would remove existing partitions and create fresh...
Creating new diag-os partition /dev/sda3 with label EDA-DIAG ...
Warning: The kernel is still using the old partition table.
The new table will be used at the next reboot.
The operation has completed successfully.
volume label EDA-DIAG on device /dev/sda3
mke2fs 1.42.8 (18-May-2021)
Filesystem label=EDA-DIAG
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
Stride=0 blocks, Stripe width=0 blocks
65536 inodes, 262144 blocks
13107 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=268435456
8 block groups
Installing Dell EMC Networking OS on the S6100-ON
using ONIE
NOTE:
You will need the Dell EMC Networking OS installer package, ONIE-FTOS-S6100-ON-9.14.2.10.bin to install
the Dell EMC Networking OS on your S6100-ON system that has only ONIE.
To install the Dell EMC Networking OS version 9.14(2.10) on a new S6100-ON device, perform the following steps:
1. Reboot the system. During the reboot process, the system displays the following message prompting you to press the Esc
key in order to stop the autoboot process:
Grub 1.99~rc1 (Dell EMC)
Built by build at bsdlab on Tue_May_18_10:41:12_UTC_2021
S6100 Boot Flash Label 3.25.2.14 NetBoot Label 3.25.2.14
2. At this prompt message, press the Esc key. The following menu appears:
Grub 1.99~rc1 (Dell EMC)
Built by root at ubuntu on Tue_May_18_10:41:12_UTC_2021
12