Reference Guide
Table Of Contents
- Dell EMC OpenManage SNMP Reference Guide Version 10.1.0.0
- Contents
- Introduction
- What is new in this release
- Supported SNMP Versions
- Managed Object Used in This Document
- Server Administrator Instrumentation MIB
- Server Administrator Baseboard Management Controller, ASF MIB
- Server Administrator Storage Management MIB
- Server Administrator Field Replaceable Unit MIB
- Server Administrator Change Management MIB
- Basic Terminology
- Frequently Used Terms in Variable Names
- Tables
- Section Organization
- Other Documents You May Need
- Introduction to the Server Administrator SNMP Subagent
- System Battery Table
- Amperage Probe Table
- Power Unit Group
- Power Supply Table
- Power Usage Table
- Voltage Probe Table
- System Information Group
- Server Administrator Group
- Instrumentation MIB Version Group
- Systems Management Software Group
- System State Group
- Chassis Information Group
- Operating System Group
- System Resource Group
- Power Group
- Thermal Group
- Remote Flash BIOS Group
- Port Group
- Device Group
- Device Tables
- Pointing Device Table
- Keyboard Device Table
- Processor Device Table
- Processor Device Status Table
- Cache Device Table
- Memory Device Table
- Memory Device Mapped Address Table
- Generic Device Table
- PCI Device Table
- PCI Device Configuration Space Table
- Network Device Table
- Managed System Services Device Table
- SD Card Unit Table
- SD Card Device Table
- Device Group Variable Values
- Device Tables
- Slot Group
- Memory Group
- BIOS Setup Control Group
- Local Response Agent Group
- Cost of Ownership Group
- Cluster Group
- Baseboard Management Controller Group
- Field Replaceable Unit Group
- Storage Management Group
- Storage Management Group
- Storage Management Information Group
- Global Data Group
- Physical Devices Group
- Controller Table
- Channel Table
- Enclosure Table
- Array Disk Table
- Array Disk Enclosure Connection Table
- Array Disk Channel Connection Table
- Fan Table
- Fan Connection Table
- Power Supply Table
- Power Supply Connection Table
- Temperature Probe Table
- Temperature Probe Connection Table
- Enclosure Management Module Table
- Enclosure Management Module Connection Table
- Battery Table
- Battery Connection Table
- Tape Drive Table
- NVME adapter table
- Logical Devices Group
- Storage Management Event Group
- Change Management Group
- SNMP Traps
- Storage Management Alert Reference
- Standard Data Type Definitions
- SNMP Sample Output
Table 336. Hard-Drive Fault LED Control Settings (continued)
enabled(2)
The hard-drive fault LEDs’ state is disabled (offline, a
binary 0 value) or enabled (online, a binary 1 value).
notReady(4)
The hard-drive fault LEDs’ state is not ready.
reset(8)
The hard-drive fault LEDs have been reset.
resetAndEnable(10)
The hard-drive fault LEDs have been reset and enabled.
Table 337. Chassis Identification Control Capabilities
Variable Name : DellChassisIdentifyControlCapabilities
Data Type: Integer
Possible Data Values Meaning of Data Value
none(0)
The LEDs do not have any chassis identification
capabilities.
unknownCapabilitie
s(1)
The chassis identification control’s capabilities are
unknown.
enableCapable(2)
The chassis identification controls can be disabled
(offline, a binary 0 value) or enabled (online, a binary
1 value).
notReadyCapable(4)
The chassis identification control’s capabilities are not
ready.
identifyCapable(8)
The chassis identification control’s LEDs can be made
to identify the chassis.
resetAndEnable(10)
The hard-drive fault LEDs have been reset and enabled.
NOTE: Chassis identification capabilities allow system administrators to set front panel light-emitting diodes (LEDs) to blink
when the chassis has malfunctioning components. When enabled, the blinking lights help administrators locate the problem
chassis.
Table 338. Chassis Identification Control Settings
Variable Name : DellChassisIdentifyControlSettings
Data Type: Integer
Possible Data Values Meaning of Data Value
unknown(1)
The chassis identification control’s state is unknown..
enabled(2)
The chassis identification control’s state is disabled
(offline, a binary 0 value) or enabled (online, a binary
1 value).
notReady(4)
The chassis identification control’s state is not ready.
identifyChassis(8)
The chassis identification control’s LEDs may be
returned to (normal) 0, or (identify chassis) 1.
identifyChassisAnd
Enable (10)
The chassis identification control’s LEDs may be
returned to normal (a binary 0 value), or identify
chassis and enabled (a binary 1 value).
Table 339. Host Control Capabilities
Variable Name : DellHostControlCapabilities
NOTE: An operator can manually enable these actions using SNMP.
Server Administrator Group 83