Release Notes

3. Click Preferences.
4. Click Advanced in the left sidebar.
5. Click Proxies in the left sidebar.
6. Enter the RAC IP address in the No Proxy for: field.
7. Click OK and then close the browser.
● To view the RAC Web-based interface when using Mozilla 1.6, you must configure your cookie settings to Enable all
cookies.
● To enable all cookies, go to the menu options and click Edit > Preferences > Privacy & Security > Cookies, and then
select Enable all cookies. If you do not perform these steps, you cannot log on to the Web interface and a message
appears indicating that your username and password are incorrect.
● DF384362: Redundancy Status displays as Not Applicable in ESXi even when NICs are teamed. On VMware ESXi
systems, NIC teaming status may not display up in the Server Administrator network section. This is an expected behavior
due to the operating system limitation and has no functional impact to the system.
● DF384061: Self-signed certificate does not enable the compatibility listener in Windows 2008 R2 managed node. On a
Windows 2008 R2 managed node, a valid CA signed certificate is required to create compatibility mode WinRM Listener. You
cannot create a compatibility mode listener with a self-signed certificate.
● DF380725: On Internet Explorer or Firefox Web browsers, you cannot attach files to an e- mail if the filename contains
non-ASCII letters. To attach files to an e-mail, rename files to contain ASCII characters.
● On YX2X generation of PowerEdge servers, Server Administrator displays the Embedded Systems Management (ESM) or
hardware logs. However, when the maximum limit for number of logs that can be recorded is reached, the existing oldest
logs are overwritten. But for YX1X generation of PowerEdge servers or prior, when the maximum limit is reached, the
information logging is stopped.
● DF523827: On Citrix XenServer 6.0 or later, if the Alert on Console alert action is configured from the Server Administrator
CLI or GUI, the alert message may not be displayed in a readable format.
● BITS113585: Server Administrator does not log CPU or CMOS Battery Probe Alerts and does not send SNMP traps.
● To resolve this issue, stop the USB arbitration service and run the Inventory Collector. To stop the USB arbitration service:
1. Run the ps aux|grep usb command to check if the USB arbitration service is running.
2. Run the chkconfig usbarbitrator off command to prevent the USB arbitration service from starting during boot.
3. After the USB arbitrator service is stopped, reboot the server to allow the Inventory collector to run.
● DF520449: On all versions of the ESX, the following USB connection error messages are generated. These messages can be
ignored. The following is a typical message:
Table 1. USB connection error message
Vendor: iDRAC Model: MAS022 Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Table 2. USB connection error message
Vendor: iDRAC Model: SECUPD Rev: 0329
Type: Direct-Access ANSI SCSI revision: 02
● DF531509: The setup and/or system password configuration from the Server Administrator GUI or CLI is successful, but the
password is displayed as blank instead of asterisk (*) on the F2 BIOS page.
● BITS086423: After an upgrade to the current version, Server Administrator does not retain the support link information on
the Preferences page.
● BITS091830: Distributed Web Server (DWS) connection does not work if you have installed the sblim-sfcb rpm from SLES11
SP3 operating system DVD. To make the connection work, install sblim-sfcb rpm either from SLES11 SP2 or from OM DVD.
● BITS040184: User in IDRAC user authentication page showing operator privilege(IDRAC user privileges) is displayed as
Custom in Server Administrator.
● With the following wsman rpm versions getting carried in SLES12 OS,OMSA DWS does not work. Update these rpms having
same or later versions from SUSE
openwsman-server-2.4.11-2.18.x86_64.rpm ,libwsman1-2.4.11-2.18.x86_64.rpm,
libwsman_clientpp1-2.4.11-2.18.x86_64.rpm
● On clicking the apply button twice on the BIOS setup page, the Server preference page and SNMP configuration page the
Server Administrator will logout from the current session.
12