CLI Guide

Example to Reset the configuration on controller 1.
Example
omconfig storage controller action=resetconfig controller=1
omconfig Create Virtual Disk
The Dell EMC OpenManage Online Help provides additional information about creating virtual disks.
The omconfig syntax for creating a virtual disk has several parameters. You must specify the following parameters:
• Controller (controller=id)
• RAID level (raid=<c| r0 | r1 | r1c | r5 | r6 | r10 | r50 | r60>
• Size (size=<number | max | min>)>
Physical disk is specified as either:
• For SCSI, SATA, and ATA controllers:
pdisk=connector:enclosureID:targetID
where connector:enclosureID:targetID is the connector number, enclosure number, and slot number.
• For SAS controllers:
pdisk=connector:targetID
where connectorID:targetID is the connector number and the slot number. For example, pdisk=0:2
Storage Management supplies default values for any of the other parameters that you do not specify.
For creating an encrypted virtual disk, specify secureflag=yes. You can create encrypted virtual disks only with SED drives.
Complete Syntax:
omconfig storage controller action=createvdisk controller=id raid=<c| r0 | r1 | r1c | r5 | r6
| r10 | r50 | r60>size=<number | max | min> pdisk=<PDISKID> [stripesize=stripesize=< 2kb|
4kb| 8kb| 16kb| 32kb| 64kb | 128kb>] [cachepolicy=<d | c>] [diskcachepolicy=<disabled |
enabled>][readpolicy=<ra | nra | ara | rc | nrc>] [writepolicy=<wb| wt| wc| nwc | fwb>]
[name=<string>] [spanlength=<n>] | [secureflag=yes][vdpienabled=yes]
NOTE:
If the command-line interface does not support commas (,) as parameter separators, then use double quotation
marks (“) to run the CLI command. Example, use pdisk="0:1:1,0:1:2" instead of pdisk=0:1:1,0:1:2 .
NOTE: If you are configuring RAID for SAS controllers with firmware version 6.1 and later, spanlength is an optional
parameter (default=2). Spanlength is an even number and is lesser than or equal to half the number of physical disks
specified in
size.
NOTE: The vdpienabled is an optional argument and is valid only on PERC9 controllers. If set to yes a T10 Protection
Information (PI) enabled virtual disk is created.
NOTE: For RAID 10 creation, PERC 9 firmware suggests the layout (number of array disks) with uneven span (spans
with unequal number of array disks), though in a span the number of disks remains even. For example, for 32 disks,
RAID 10 gets created with all the disks in one span and for 34 disks, RAID 10 gets created with 16 disks in one span and
18 disks in the other span.
Example Syntax:
You can create a RAID-5 virtual disk of 500 MB with a stripe size of 16 KB on a PERC 3/QC controller. The name of the virtual disk is vd1
and it resides on connector 0 of controller 1. Because the virtual disk is a RAID-5, it requires at least three physical disks. In this example,
you specify four physical disks. These are physical disks 0 through 3. The virtual disk has read-ahead, write–through caching, and cache
I/O policies.
To create a virtual disk:
omconfig storage controller action=createvdisk controller=1 raid=r5 size=500m pdisk=
0:0,0:1,0:2,0:3 stripesize=16kb cachepolicy=c readpolicy=ra writepolicy=wt
154
Omconfig storage commands