Users Guide
omreport Power Supply Status
Table 15-10. omreport Power Supply Commands
omreport EMM Status
Table 15-11. omreport EMM Commands
omreport Physical Disk Status
Table 15-12.omreportPhysicalDiskCommands
where id is the controller number and <ENCLOSUREID> is the enclosure ID.
Example for SCSI controllers: controller=0 enclosure=2 info=fans. Example for SAS
controllers: controller=0 enclosure=1:2 info=fans.
information on specifying enclosures.
controller=id enclosure=<ENCLOSUREID> info=fans index=n
where id is the controller number and <ENCLOSUREID> is the enclosure ID and n
is the number of a fan. Example for SCSI controllers: controller=0 enclosure=2
info=fans index=1. Example for SAS controllers: controller=0 enclosure=1:2
info=fans index=1.
Displays the specified fan. See
"enclosure=<ENCLOSUREID> Parameter" for more
information on specifying enclosures.
Required
Command
Levels (1, 2,
3)
Optional name=value Pairs
Use
omreport
storage
enclosure
Displays property information for all enclosures
attached to the system.
controller=id enclosure=<ENCLOSUREID> info=pwrsupplies
where id is the controller number and <ENCLOSUREID> is the enclosure ID.
Example for SCSI controllers: controller=0 enclosure=2 info=pwrsupplies. Example
for SAS controllers: controller=0 enclosure=1:2 info=pwrsupplies.
Displays the power supplies for the specified
enclosure. See "enclosure=<ENCLOSUREID>
Parameter" for more information on specifying
enclosures.
controller=id enclosure=<ENCLOSUREID> info=pwrsupplies index=n
where id is the controller number and <ENCLOSUREID> is the enclosure ID and n
is the number of a power supply. Example for SCSI controllers: controller=0
enclosure=2 info=pwrsupplies index=1. Example for SAS controllers: controller=0
enclosure=1:2 info=pwrsupplies index=1.
Displays the specified power supply. See
"enclosure=<ENCLOSUREID> Parameter" for more
information on specifying enclosures.
NOTE: The status of the EMMs is displayed as degraded if there is a mismatch between the EMM firmware.
Required
Command
Levels (1, 2,
3)
Optional name=value Pairs
Use
omreport
storage
enclosure
Displays property information for all enclosures attached to
the system.
controller=id enclosure=<ENCLOSUREID> info=emms
where id is the controller number and <ENCLOSUREID> is the enclosure ID.
Example for SCSI controllers: controller=0 enclosure=2 info=emms. Example
for SAS controllers: controller=0 enclosure=1:2 info=emms.
Displays the enclosure management modules (EMMs) for
the specified enclosure. See "enclosure=<ENCLOSUREID>
Parameter" for more information on specifying enclosures.
controller=id enclosure=<ENCLOSUREID> info=emms index=n
where id is the controller number and <ENCLOSUREID> is the enclosure ID
and n is the number of an EMM. Example for SCSI controllers: controller=0
enclosure=2 info=emms index=1. Example for SAS controllers: controller=0
enclosure=1:2 info=emms index=1.
Displays the specified EMM. See
"enclosure=<ENCLOSUREID> Parameter" for more
information on specifying enclosures.
Required Command
Levels (1, 2, 3) and
name=value Pair
Optional name=value Pairs
Use
omreport storage
pdisk controller=id
where id is the
Displays all physical disks attached to the
specified controller.
NOTE: If a physical disk was replaced by