Migration from Dell Lifecycle Controller Integration Version 3.3 for Microsoft System Center Configuration Manager to OpenManage Integration Version 7.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright ©2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Introduction....................................................................................................................................................4 2 Saving user data from DLCI for SCCM...........................................................................................................5 3 Uninstalling DLCI for SCCM...........................................................................................................................6 4 Setting up OMIMSSC....................
1 Introduction This technical document describes how user can migrate from Dell Lifecycle Controller Integration Version 3.3 for Microsoft System Center Configuration Manager (DLCI for SCCM) to OpenManage Integration Version 7.0 for Microsoft System Center (OMIMSSC). OMIMSSC does not support upgrade from DLCI for SCCM, and hence manual migration of data is required.
2 Saving user data from DLCI for SCCM About this task Before migrating from DLCI for SCCM to OMIMSSC, ensure that you capture all the user details from DLCI for SCCM. The details to be captured are listed below. Steps 1 Note down the credentials (user name and password) used to discover servers in DLCI for SCCM. 2 Share path of boot images or supporting files—WIM files can be used in OMIMSSC to re-create boot images. 3 Save a local copy of the purchased license file.
3 Uninstalling DLCI for SCCM Uninstall DLCI for SCCM to proceed further with the migration. For more information, see Uninstalling Dell Lifecycle Controller Integration for Configuration Manager section of Dell Lifecycle Controller Integration Version 3.3 for Microsoft System Center Configuration Manager Installation Guide.
4 Setting up OMIMSSC About this task Once you uninstall DLCI for SCCM, install and launch OMIMSSC. To configure OMIMSSC, perform the following steps. Steps 1 Setting up OMIMSSC Appliance— create and configure a VM for OMIMSSC. 2 Launch admin portal to download OMIMSSC components. 3 Download and install, Integration Gateway and OMIMSCC console extension for SCCM. 4 Enroll SCCM with OMIMSSC. 5 Launch OMIMSSC console extension for SCCM.
5 Recreating data in OMIMSSC About this task This section provides information on how to migrate or re-create the user data captured in Saving user data from DLCI for SCCM. Steps 1 Credential profile for discovery—create a Device Type Credential profile with the saved credential profile to discover servers that were already discovered in DLCI for SCCM. You can discover Dell EMC servers by synchronizing SCCM with OMIMSSC or using their iDRAC IP address.
6 Feature mapping and migration data Feature mapping between DLCI for SCCM and OMIMSSC and data migration information: Table 1.
FC HBA Adapter Comparison Report Configuration and Deployment > Assign Operational Template and Run Compliance Configuration Utility Create New Lifecycle Controller (LC) Boot Media LC Boot Media Creation Hardware Configuration and Operating System Deployment Profiles and Templates > Operational Template > Create Configuration and Deployment > Assign Operational Template and Run Compliance Firmware inventory, compare and update Maintenance Center view Maintenance Center > Run Update Maintenance Center
is stored as Operational Template. Hence, the hardware profile information cannot be re-used. OpenManage Integration for Microsoft System Center User's Guide. Task Sequence Task sequences has references to packages from DLCI for SCCM. Hence, task sequences created in DLCI for SCCM cannot be exported in OMIMSSC. For information about creating a task sequence, see Creating task sequence section in OpenManage Integration for Microsoft System Center User's Guide.
7 Accessing documents from the Dell EMC support site You can access the required documents using the following links: • For Dell EMC Enterprise Systems Management documents — Dell.com/SoftwareSecurityManuals • For Dell EMC OpenManage documents — Dell.com/OpenManageManuals • For Dell EMC Remote Enterprise Systems Management documents — Dell.com/esmmanuals • For iDRAC and Dell EMC Lifecycle Controller documents — Dell.
