White Papers
Table Of Contents
- 1
- 1
- 1
- 1 Introduction
- 2 Bare-metal discovery
- 1
- 1
- 1
- 1
- 1
- 3 Create an ISO Profile
- 4 Best practices for OS deployment
- 4.1 Customized ISO images
- 4.2 Lifecycle Controller busy
- 1.1
- 4.3 Disconnected network interfaces
- 4.4 First boot disk selection
- 4.5 Correct boot sequence
- 4.6 Boot sequence enablement
- 4.7 Virtual Disk should be created for controller (PERC or BOSS)
- 4.8 In Multi-NIC environment, selection of right OMIVV network selection is important
- 4.9 OMIVV does not support software controller
- 1.1
- 4.10 Ensure while providing static network details, valid network details are entered
- 4.11 Minimum requirements for ESXi installation
- 4.12 vCenter license for adding host to vCenter after deployment
- 4.13 OMIVV does not support installation of ESXi on virtual machine
- 4.14 Ensure that OMIVV license for host is available
- 4.15 ESXi password requirements
- 4.16 Port information for ESXi installation
- 1.1
- 1.1
- 4.17 ESXi deployment failure
- 1.1
- 1.1
- 1.1
- 1.1
- 1.1
- 1.1
- 1.1
- 1.1
- 4.18 When NPAR is enabled on target node and disabled in System Profile, ESXi deployment fails
- 1.1
- 4.19 Sometimes MAC address is populated during ESXi deployment
- 1.1
- 1.1
- 4.20 After ESXi deployment, OMIVV fails to add ESXi host to vCenter or failed to add host profile or enter maintenance mode is failed for host
- 1.1
- 4.21 After performing ESXi deployment, host is either disconnected or not responding state
- 1.1
- 1.1
- 1.1
- 4.22 Deployment job times out when network interface card (NIC) of OMIVV is not connected to the ESXi host network
- 1.1
- 1.1
- 4.23 General failure
- 1.1
- 4.24 Inaccessible network shares (OSD47, OSD17)
- 1.1
- 4.25 Auto discovered systems are displayed without model information in Deployment wizard
- 4.26 Server pending reboot
- 4.27 Boot order is not guaranteed in UEFI mode
- 4.28 Host credential profile having AD credentials are not listed in deployment page
- 4.29 Even though ESXi deployment is successful, inventory fails when selected ISO profile has ESXi 6.5 (or earlier version) image and host credential profile have different or no ESXi password other than which is set in deployment wizard
- 4.30 After performing an ESXi deployment, existing iDRAC jobs are not in seen
- 4.31 After performing upgrade to latest version, scheduled ESXi deployment job fails
- 1.1
- 4.32 Discovered user used during bare-metal discovery is disabled after performing ESXi deployment
- 4.33 ESXi deployment is blocked when secure boot is enabled
- 4.34 Deployment fails when other OS (RHEL or WINDOWS) is previously installed
- 5 Conclusion
15 ESXi deployment using Dell EMC OpenManage Integration for VMware vCenter (OMIVV) and deployment best
practices
Notes: VMware supports ESXi installation on SD cards for 6.7 U3 and earlier versions.
Based on the presence of the modules supported, an appropriate target is available for you to select during
deployment.
Figure 9: Installation targets
You can select the multiple servers at a time for an ESXi deployment. Installation target selection is a one-
time operation for all the servers that are selected for the deployment job.
If one or more servers have IDSDM or BOSS module, applicable targets are available for installation target
selection.
In this scenario, if IDSDM or BOSS is selected as installation target, the servers on which the selected target
is not present will be skipped from performing deployment. This is notified in the target selection page.
There is also an option to not to skip the servers which do not have selected target present.
You can force deploy the an ESXi on First boot disk and ensure that ESXi is deployed on all the selected
servers.
Note: OS deployment is blocked from iDRAC firmware version 4.00.00.00 to 4.32.20.00 when secure boot is
enabled.