Users Guide
Table Of Contents
- Dell EMC OpenManage Enterprise-Modular Edition Version 1.00.10 for PowerEdge MX7000 Chassis User's Guide
- Overview
- Updating the management module firmware
- Logging in to OME-Modular
- Logging in to OME–Modular as local, Active Directory, or LDAP user
- OME-Modular home page
- Viewing device health
- Setting up chassis
- Initial configuration
- Configuring chassis settings
- Managing chassis
- Chassis groups
- Controlling chassis power
- Backing up chassis
- Restoring chassis
- Exporting chassis profiles
- Managing chassis failover
- Troubleshooting in chassis
- Blinking LEDs
- Interfaces to access OME-Modular
- Viewing chassis hardware
- Viewing chassis alerts
- Viewing chassis hardware logs
- Configuring OME–Modular
- Managing compute sleds
- Managing Storage
- Managing templates
- Managing identity pools
- Ethernet IO Modules
- MX scalable fabric architecture
- SmartFabric Services
- Managing networks
- Managing Fibre Channel IOMs
- Managing firmware
- Monitoring alerts and logs
- Monitoring audit logs
- Troubleshooting
- Storage
- Firmware update is failing
- Storage assignment is failing
- SAS IOM status is downgraded
- SAS IOM health is downgraded
- Drives on compute sled are not visible
- Storage configuration cannot be applied to SAS IOMs
- Drives in OpenManage are not visible
- iDRAC and OpenManage drive information do not match
- The assignment mode of storage sled is unknown
- Storage
- Recommended slot configurations for IOMs
2. If the host OS is Windows, the LACP timer MUST be set to “slow” (also referred to as “normal”)
For the list of supported operating systems, see Dell EMC PowerEdge MX7000 Enclosure Installation and Service Manual.
NOTE: In the fabric mode, if an LACP team is created with four port and you want to delete two ports from the LACP
team, you must delete the entire LACP team and create a new LACP team with two ports.
For detailed NIC teaming instructions, refer to the network adapter or operating system documentation.
CLI commands available in Fabric mode
When operating in Fabric mode, most of the switch configuration is managed through the OME–Modular GUI. Some OS10
functionality, such as L3 routing, are disabled. Owing to the disabling, a switch operating in Fabric mode supports all OS10 show
commands, but only the below subset of CLI configuration commands:
● clock—Configure clock parameters.
● end—Exit to the EXEC mode.
● exit—Exit from current mode
● help—Display available commands.
● hostname—Set the system host name.
● interface—Configure or select an interface.
● ip name-server—Configure the IP address of up to three name servers
●
logging—Configure system logging.
● management route—Configure the IPv4/IPv6 management route
● no—Delete or disable commands in Configuration mode.
● ntp—Configure Network time protocol.
● snmp-server—Configure SNMP server.
● username—Create or modify user credentials.
● spanning-tree
○ disable— Disable spanning tree globally.
○ mac-flush-timer— Set the time used to flush MAC address entries.
○ mode— Enable a spanning-tree mode, such as RSTP or MST.
○ mst— Configure multiple spanning-tree (MST) mode.
○ rstp— Configure rapid spanning-tree protocol (RSTP) mode.
○ vlan— Configure spanning-tree on a VLAN range.
Viewing fabric details
To view details an existing fabric:
● From the Devices drop down, select Fabric.
● From the fabrics table, select the fabric and click View Details.
The Fabric Details page is displayed.
Adding fabric
To add a fabric:
1. Click Devices > Fabric .
The Fabric page is displayed.
2. Click Add Fabric.
The Create Fabric window is displayed.
3. Enter Name and Description, and then click Next.
4. Select the Design Type from the drop-down.
The available options are:
● 2xMX5108n Ethernet Switches in same chassis
62
SmartFabric Services