Users Guide
Table Of Contents
- Dell EMC OpenManage Enterprise-Modular Edition for PowerEdge MX7000 Chassis User's Guide
- Contents
- Overview
- Updating firmware for PowerEdge MX solution
- MX7000 Solution Baselines
- Upgrading ethernet switch using DUP
- OME-Modular licenses
- Logging in to OME-Modular
- Logging in to OME–Modular as local, Active Directory, or LDAP user
- Logging in to OME-Modular using OpenID Connect
- OME-Modular home page
- Viewing device health
- Setting up chassis
- Initial configuration
- Configuring chassis settings
- Managing chassis
- Chassis groups
- Controlling chassis power
- Backing up chassis
- Restoring chassis
- Exporting chassis profiles
- Managing chassis failover
- Troubleshooting in chassis
- Blinking LEDs
- Interfaces to access OME-Modular
- Viewing chassis hardware
- Viewing chassis alerts
- Viewing chassis hardware logs
- Configuring OME–Modular
- Viewing current configuration
- Configuring users and user settings
- Configuring login security settings
- Configuring alerts
- Managing compute sleds
- Managing Profiles
- Managing storage
- Managing templates
- Managing identity pools
- Ethernet IO Modules
- MX Scalable Fabric architecture
- SmartFabric Services
- Managing networks
- Managing Fibre Channel IOMs
- Managing firmware
- Monitoring alerts and logs
- Monitoring audit logs
- Use case scenarios
- Troubleshooting
- Storage
- Firmware update is failing
- Storage assignment is failing
- SAS IOM status is downgraded
- SAS IOM health is downgraded
- Drives on compute sled are not visible
- Storage configuration cannot be applied to SAS IOMs
- Drives in OpenManage are not visible
- iDRAC and OpenManage drive information do not match
- The assignment mode of storage sled is unknown
- Unable to access OME-Modular using Chassis Direct
- Troubleshooting lead chassis failure
- Storage
- Recommended slot configurations for IOMs
- Upgrading networking switch using different OS10 DUP versions
- Upgrading networking switch using CLI
Configuring IOM synchronization
You can replicate the time and alert destination configuration of the lead chassis in the network and FC IOMs.
To configure the time and alert destination:
1. Click Application Settings > Network > IOM Synchronization Configuration.
2. Select the Replicate Time Configuration from Chassis and Replicate Alert Destination Configuration from Chassis
check boxes.
● MXG610s supports only three SNMP destination unlike OS10 which supports four SNMP destinations.
○ Using SNMP, IPV4 and IPV6 replication is supported from OME-Modular to IOM.
○ Using SNMP, FQND and Host Name is supported only if DNS Address for FC IOM (Pre-requisite for DNS
configuration) is Static management IP Address configuration.
○ Using SNMP, SNMPV2 replication is supported for OS10 and SNMPV1 replication is supported for FC IOM.
● MXG610s supports four Syslog destinations same as MSM.
○ Using Syslog, only 514-port number is supported from MSM to Network IOM.
○ Using Syslog, 10 to 65535-port number is supported from MSM to FC IOM. Port number is configured as a secure
port.
3. Click Apply to save the changes.
In MCM environment, the IOM network synchronization configuration is propagated from the lead to the member chassis
only if the time and alert destination options are selected while creating the chassis group or adding members to the group.
Changing device naming and preference
1. Click Application Settings > Network > Device Name Preference.
2. Select the naming preference.
Ports and protocols supported in OME-Modular
The table below lists the protocols and ports that are supported in OME-Modular.
Table 13. Ports and protocols that are supported in OME-Modular (continued)
Port number Protocol Port type Maximum
encryption
level
Source Direction Destination Usage
22 SSH TCP 256-bit External
application
In OME-Modular Required for
incoming only
if FSD is used.
OME-Modular
administrator
must enable
this port only
while
interacting
with Dell
EMC.
25 SMTP TCP None OME-Modular Out External
Application
To receive
email alerts
from
OpenManage
Enterprise.
53 DNS UDP/TCP None OME-Modular Out External
Application
For DNS
Queries
80 HTTP TCP None External
Application
In OpenManage
Enterprise
Modular
The Web GUI
landing page.
Will redirect a
Logging in to OME-Modular 59