Users Guide
Table Of Contents
- Dell EMC OpenManage Enterprise-Modular Edition for PowerEdge MX7000 Chassis User's Guide
- Contents
- Overview
- Updating firmware for PowerEdge MX solution
- MX7000 Solution Baselines
- Upgrading ethernet switch using DUP
- OME-Modular licenses
- Logging in to OME-Modular
- Logging in to OME–Modular as local, Active Directory, or LDAP user
- Logging in to OME-Modular using OpenID Connect
- OME-Modular home page
- Viewing device health
- Setting up chassis
- Initial configuration
- Configuring chassis settings
- Managing chassis
- Chassis groups
- Controlling chassis power
- Backing up chassis
- Restoring chassis
- Exporting chassis profiles
- Managing chassis failover
- Troubleshooting in chassis
- Blinking LEDs
- Interfaces to access OME-Modular
- Viewing chassis hardware
- Viewing chassis alerts
- Viewing chassis hardware logs
- Configuring OME–Modular
- Viewing current configuration
- Configuring users and user settings
- Configuring login security settings
- Configuring alerts
- Managing compute sleds
- Managing Profiles
- Managing storage
- Managing templates
- Managing identity pools
- Ethernet IO Modules
- MX Scalable Fabric architecture
- SmartFabric Services
- Managing networks
- Managing Fibre Channel IOMs
- Managing firmware
- Monitoring alerts and logs
- Monitoring audit logs
- Use case scenarios
- Troubleshooting
- Storage
- Firmware update is failing
- Storage assignment is failing
- SAS IOM status is downgraded
- SAS IOM health is downgraded
- Drives on compute sled are not visible
- Storage configuration cannot be applied to SAS IOMs
- Drives in OpenManage are not visible
- iDRAC and OpenManage drive information do not match
- The assignment mode of storage sled is unknown
- Unable to access OME-Modular using Chassis Direct
- Troubleshooting lead chassis failure
- Storage
- Recommended slot configurations for IOMs
- Upgrading networking switch using different OS10 DUP versions
- Upgrading networking switch using CLI
2. Reset the active MM manually.
3. After the failover or reset is complete, check the firmware version to verify if the active MM is running the same or a later
version of OME-Modular, as the standby MM. If not, perform a reset on the MM to force failover.
4. Retry the firmware update.
Upgrading ethernet switch using DUP
NOTE: Upgrade the MX9116n and MX5108n switches only after updating the other MX7000 components to their
corresponding PowerEdge MX 1.30.00 baseline versions.
NOTE: The DUP update procedure is recommended for upgrading OS10, firmware, and ONIE on the MX9116n and MX5108n
switches.
NOTE: Upgrade the MX9116n and MX5108n switches to 10.5.1.X and later, only if the switches running are 10.5.0.7 or later.
Upgrading networking OS10 using DUP
To upgrade OS10 using DUP, follow these steps:
1. Download the latest DUP file for the switch from https://www.dell.com/support.
2. On the OME-Modular web interface, go to Devices > I/O Modules.
3. Select the IOM module on which you must carry out the OS10 upgrade.
4. Click Update Firmware.
5. Select the Individual package option, then click Browse and go to the location where the OS10 DUP was downloaded earlier.
Wait for the compliance report, once done, the supported components are displayed.
6. Select the required components and click Update, to start the update.
For upgrading from different versions earlier than 10.5.0.7, see Upgrading networking switch using different DUP versions
section.
7. Go to Monitoring > Jobs page, to view the job status.
Upgrading Firmware and ONIE using DUP
NOTE: ONIE upgrade using DUP method is supported only if all the IOMs in the group are in 10.5.2.3 and later
To upgrade ONIE using DUP, follow these steps:
1. Download the latest ONIE DUP file for the switch from https://www.dell.com/support.
2. On the OME-Modular web interface, go to Devices > I/O Modules.
3. Select the IOM module on which you must carry out the ONIE upgrade.
4. Click Update Firmware.
5. Select the Individual package option, then click Browse and go to the location where the ONIE DUP was downloaded earlier.
Wait for the compliance report, once done, the supported components are displayed.
6. Select the required components and click Update, to start the update.
7. Go to Monitoring > Jobs page, to view the job status.
OS10 firmware update matrix
Table 4. OS10 firmware update matrix
Updating firmware for PowerEdge MX solution 21