Users Guide

used in these scripts are set in the TKENVSET.BAT or tkenvet.sh scripts. You can specify the IP address to congure the RAC as an
optional parameter. The raccfg.ini le is generated with the RACCAP.BAT or raccap.sh sample script. For information about using the
RACCAP.BATor raccap.sh sample script to capture RAC conguration information, see RACCAP.BAT Or raccap.sh.
NOTE: On all PowerEdge systems, racrep.sh and sysrep.sh have duplicate functions. If you run racrep.sh followed by sysrep.sh,
the latter overwrites the settings of the former.
RAIDCFG.BAT or raidcfg.sh
The RAIDCFG.BAT or raidcfg.sh sample script congures RAID controllers detected on the system. User input is optional to run this script.
The input parameter is a name or path to a log le. This parameter is not set to any value by default, and no log le is generated. The
default variable values used in this script are set in the
TKENVSET.BAT or tkenvest.sh scripts. This script uses the RAIDCFG.EXE or
raidcfg.sh utility to automatically congure the detected controllers on your target system. For example, for the rst controller discovered, if
RAIDCFG.EXE or raidcfg.sh discovers only one attached hard drive, the script tries to create RAID 0; if two hard drives are discovered, a
RAID 1 conguration is enabled; if three or more hard drives are discovered, a RAID 5 conguration is enabled.
NOTE: On the detected controller, a RAID virtual disk is created only if the array disks connected to that particular controller
have space available and, where applicable, are not part of existing array group.
SYSREP.BAT or sysrep.sh
The SYSREP.BAT or sysrep.sh sample script applies SYSCFG options to the target system based on conguration information that has
been saved in a conguration le. User input is optional to run this script, depending on the variable settings in the SYSREP.BAT or
sysrep.sh scripts. This script uses the SYSCFG utility to congure the BIOS and BMC in the target system using the conguration le
syscfg.in. The syscfg.in is the rst parameter passed to this script. If this parameter is not passed, the default variables values used in this
script are set in the SYSREP.BAT or sysrep.sh scripts. The syscfg.ini le is generated with the SYSCAP.BAT or syscap.sh sample script. For
information about using the SYSCAP.BAT or syscap.sh sample script to capture BIOS and BMC settings, see SYSCAP.BAT Or syscap.sh.
The second parameter is a name or path to a log le. This parameter is not set to any value by default, and no log le is generated.
NOTE
: If the replication requires a change in the memory redundancy mode, reboot the target server and run the script again
to complete the replication.
NOTE: The racrep.sh and sysrep.sh have duplicate functions. If you run racrep.sh after the command sysrep.sh, the latter
overwrites the former settings.
PARTCFG.BAT or partcfg.sh
In BIOS mode, the PARTCFG.BAT or partcfg.sh sample script creates and populates the Dell utility partition using UPINIT.BAT or upinit.sh
and creates the deployment partition on a specied disk. In UEFI mode, the partcfg.sh sample script creates the deployment partition on a
specied disk. For more information about using the UPINIT.BAT or upinit.sh tool, see UPINIT.BAT Or upinit.sh. User input is not required to
run this script. The default variable values used in this script are set in the TKENVSET.BAT or tkenvset.sh scripts.
NOTE
: Ensure that DT_HD is set to the required disk to be congured before you execute the PARTCFG.BAT or partcfg.sh
script.
Preparing the script les 51