Deployment Guide

6. If the DT_PARTN_UP variable is set to ON, edit the default variable value for the utility partition installation package location

(DT_UP_IMAGE=%DT_SYSTEMS%\UPIMG.BIN for Windows and DT_UP_IMAGE=$dt_systems/upimg.bin for Linux),

if applicable.

NOTE: Edit the UPIMG_BIN variable only if you have changed the name or path of the utility partition installation

package.

Editing DTK task scripts

The task scripts called by the master batch file do not require any edits (with the following exceptions) if the default variable values

are utilized in the TKENVSET.BAT or tkenvset.sh scripts. However, if you make any changes to the default values set by the

TKENVSET.BAT or tkenvset.sh, you must make the same edits to the matching default values set in the appropriate task scripts.

Locate the USER MODIFICATION REQUIRED heading in the task scripts to find the variable values you may need to edit. Each of

the following task scripts can be called by the user-written master batch script during a full deployment:

• RACREP.BAT or racrep.sh

• RAIDCFG.BAT or raidcfg.sh

• SYSREP.BAT or sysrep.sh

• PARTCFG.BAT or partcfg.sh

RACREP.BAT or racrep.sh

The RACREP.BAT or racrep.sh sample script applies RAC options to the target system based on configuration information that has

been saved in the configuration file. User input is optional, depending on the variables set in the RACREP.BAT or racrep.sh sample

script. On systems running Windows, RACREP.BAT script uses RACADM.EXE to configure RAC in the target system. On systems

running Linux the racrep.sh script uses racadm wrapper script or the syscfg utility (depending on the version of RAC on your

system) to configure RAC in the target system. The raccfg.ini is passed as the first parameter to these scripts. If this parameter is

not passed, the default variables values used in these scripts are set in the TKENVSET.BAT or tkenvet.sh scripts. You can specify

the IP address to configure the RAC as an optional parameter. The raccfg.ini file is generated with the RACCAP.BAT or raccap.sh

sample script. For information about using the RACCAP.BATor raccap.sh sample script to capture RAC configuration information,

see RACCAP.BAT Or raccap.sh.

NOTE: On all PowerEdge systems, racrep.sh and sysrep.sh have duplicate functions. If you run racrep.sh followed by

sysrep.sh, the latter overwrites the settings of the former.

RAIDCFG.BAT or raidcfg.sh

The RAIDCFG.BAT or raidcfg.sh sample script configures RAID controllers detected on the system. User input is optional to run this

script. The input parameter is a name or path to a log file. This parameter is not set to any value by default, and no log file is

generated. The default variable values used in this script are set in the TKENVSET.BAT or tkenvest.sh scripts. This script uses the

RAIDCFG.EXE or raidcfg.sh utility to automatically configure the detected controllers on your target system. For example, for the

first controller discovered, if RAIDCFG.EXE or raidcfg.sh discovers only one attached hard drive, the script tries to create RAID 0; if

two hard drives are discovered, a RAID 1 configuration is enabled; if three or more hard drives are discovered, a RAID 5 configuration

is enabled.

NOTE: On the detected controller, a RAID virtual disk is created only if the array disks connected to that particular

controller have space available and, where applicable, are not part of existing array group.

SYSREP.BAT or sysrep.sh

The SYSREP.BAT or sysrep.sh sample script applies SYSCFG options to the target system based on configuration information that

has been saved in a configuration file. User input is optional to run this script, depending on the variable settings in the SYSREP.BAT

or sysrep.sh scripts. This script uses the SYSCFG utility to configure the BIOS and BMC in the target system using the configuration

file syscfg.in. The syscfg.in is the first parameter passed to this script. If this parameter is not passed, the default variables values

used in this script are set in the SYSREP.BAT or sysrep.sh scripts. The syscfg.ini file is generated with the SYSCAP.BAT or

syscap.sh sample script. For information about using the SYSCAP.BAT or syscap.sh sample script to capture BIOS and BMC