Users Guide

• RAIDCFG.BAT or raidcfg.sh

• SYSREP.BAT or sysrep.sh

• PARTCFG.BAT or partcfg.sh

RACREP.BAT or racrep.sh

The RACREP.BAT or racrep.sh sample script applies RAC options to the target system based on

configuration information that has been saved in the configuration file. User input is optional, depending

on the variables set in the RACREP.BAT or racrep.sh sample script. On systems running Windows,

RACREP.BAT script uses RACADM.EXE to configure RAC in the target system. On systems running Linux

the racrep.sh script uses racadm wrapper script or the syscfg utility (depending on the version of RAC on

your system) to configure RAC in the target system. The raccfg.ini is passed as the first parameter to these

scripts. If this parameter is not passed, the default variables values used in these scripts are set in the

TKENVSET.BAT or tkenvet.sh scripts. You can specify the IP address to configure the RAC as an optional

parameter. The raccfg.ini file is generated with the RACCAP.BAT or raccap.sh sample script. For

information about using the RACCAP.BATor raccap.sh sample script to capture RAC configuration

information, see RACCAP.BAT Or raccap.sh.

NOTE: On all PowerEdge systems, racrep.sh and sysrep.sh have duplicate functions. If you run

racrep.sh followed by sysrep.sh, the latter overwrites the settings of the former.

RAIDCFG.BAT or raidcfg.sh

The RAIDCFG.BAT or raidcfg.sh sample script configures RAID controllers detected on the system. User

input is optional to run this script. The input parameter is a name or path to a log file. This parameter is

not set to any value by default, and no log file is generated. The default variable values used in this script

are set in the TKENVSET.BAT or tkenvest.sh scripts. This script uses the RAIDCFG.EXE or raidcfg.sh utility

to automatically configure the detected controllers on your target system. For example, for the first

controller discovered, if RAIDCFG.EXE or raidcfg.sh discovers only one attached hard drive, the script tries

to create RAID 0; if two hard drives are discovered, a RAID 1 configuration is enabled; if three or more

hard drives are discovered, a RAID 5 configuration is enabled.

NOTE: On the detected controller, a RAID virtual disk is created only if the array disks connected to

that particular controller have space available and, where applicable, are not part of already existing

array group.

SYSREP.BAT or sysrep.sh

The SYSREP.BAT or sysrep.sh sample script applies SYSCFG options to the target system based on

configuration information that has been saved in a configuration file. User input is optional to run this

script, depending on the variable settings in the SYSREP.BAT orsysrep.sh scripts. This script uses the

SYSCFG utility to configure the BIOS and BMC in the target system using the configuration file syscfg.in.

Thesyscfg.in is the first parameter passed to this script. If this parameter is not passed, the default

variables values used in this script are set in the SYSREP.BAT or sysrep.sh scripts. The syscfg.ini file is

generated with the SYSCAP.BAT or syscap.sh sample script. For information about using the SYSCAP.BAT

or syscap.sh sample script to capture BIOS and BMC settings, see SYSCAP.BAT Or syscap.sh. The second

parameter is a name or path to a log file. This parameter is not set to any value by default, and no log file

is generated.

NOTE: If the replication requires a change in the memory redundancy mode, reboot the target

server and execute the script again to complete the replication.