Reference Guide
Dell OpenManage Client Instrumentation Reference Guide
file:///T|/htdocs/SOFTWARE/smcliins/cli80/EN/refgd/index.htm[10/19/2012 9:56:27 AM]
IsCurrent
of a SettingData subclass, there is at most one instance of ElementSettingData which references the ManagedElement and an instance of the
SettingData sub-class where there is a specified non-null, non-key property of the SettingData sub-class, and the IsMaximum property on the
referencing ElementSettingData instance has a value of "Is Maximum" or the IsMinimum property on the referencing ElementSettingData
instance has a value of "Is Minimum" and the IsCurrent property on the referencing ElementSettingData instance has a value of "Is Current".
There is at most one instance of ElementSettingData which references a ManagedElement and an instance of a SettingData sub-class where the
IsCurrent property has a value of "Is Current" and the IsMinimum property does not have a value of "Is Minimum" and the IsMaximum property
does not have a value of "Is Maximum".
Possible values are:
0 - Unknown
1 - Is Current
2 - Is Not Current
IsDefault
An enumerated integer that indicates that the referenced setting is a default setting for the element or that this information is unknown.
Possible values are:
0 - Unknown
1 - Is Default
2 - Is Not Default
IsMaximum
This property affects the interpretation of all non-null, non-enumerated, non-binary, numeric, non-key properties of the associated SettingData
instance. All other properties of the associated SettingData instance are not affected by this property.
Note: It is assumed that the semantics of each property of this set are designed to be compared mathematically.
Possible values are:
0 - Unknown - Indicates that the affected property values specified in the associated SettingData instance may correspond to maximum
desired setting values.
1 - Not Applicable - Indicates that the affected property values specified in the associated SettingData instance is not interpreted with respect
to whether each defines a desired maximum.
2 - Is Maximum - Indicates that the affected property values specified in the associated SettingData instance defines desired maximum setting
values. The operational maximum values should be modeled as a properties of the CIM_ManagedElement instance.
3 - Is Not Maximum - Indicates that the affected property values specified in the associated SettingData instance does not define desired
maximum setting values.
IsMinimum
This property affects the interpretation of all non-null, non-enumerated, non-binary, numeric, non-key properties of the associated SettingData
instance. All other properties of the associated SettingData instance are not affected by this property.
Note: It is assumed that the semantics of each property of this set are designed to be compared mathematically.
Possible values are:
0 - Unknown - Indicates that the affected property values specified in the associated SettingData instance may correspond to minimum desired
setting values.
1 - Not Applicable - Indicates that the affected property values specified in the associated SettingData instance is not interpreted with respect
to whether each defines a desired minimum.
2 - Is Minimum - Indicates that the affected property values specified in the associated SettingData instance defines desired minimum setting
values. The operational minimum values should be modeled as a properties of the CIM_ManagedElement instance.
3 - Is Not Minimum - Indicates that the affected property values specified in the associated SettingData instance does not define desired
minimum setting values.
IsNext
An enumerated integer indicating whether or not the referenced setting is the next setting to be applied. For example, the application could take
place on a re-initialization, reset, reconfiguration request. This could be a permanent setting, or a setting used only one time, as indicated by the
flag. If it is a permanent setting then the setting is applied every time the managed element reinitializes, until this flag is manually reset.
However, if it is single use, then the flag is automatically cleared after the settings are applied. Also note that if this flag is specified (that is, set
to value other than "Unknown"), then this takes precedence over any SettingData that may have been specified as Default. For example: If the
managed element is a computer system, and the value of this flag is "Is Next", then the setting will be effective next time the system resets.
And, unless this flag is changed, it will persist for subsequent system resets. However, if this flag is set to "Is Next For Single Use", then this
setting will only be used once and the flag would be reset after that to "Is Not Next". So, in the example, if the system reboots in a quick
succession, the setting will not be used at the second reboot.
Possible values are:
0 - Unknown
1 - Is Next
2 - Is Not Next
3 - Is Next For Single Use
IsPending
An enumerated integer that indicates whether or not the referenced CIM_SettingData instance represents outstanding changes to the
configuration of the referenced CIM_ManagedElement that are known to be pending and are in the process of being applied.
Possible values are:
0 - Unknown - Indicates that the referenced instance of CIM_SettingData may represent the last configuration applied to the referenced
CIM_ManagedElement.
2 - Is Pending - Indicates that the referenced instance of CIM_SettingData represents outstanding changes to the configuration of the
referenced CIM_ManagedElement that are known to be pending.
3 - Is Not Pending - Indicates that the referenced instance of CIM_SettingData does not represent outstanding changes to the configuration of
the referenced CIM_ManagedElement.
.. - DMTF Reserved
32768.. - Vendor Reserved
ManagedElement The managed element.
SettingData The SettingData object that is associated with the element.
DCIM_OrderedMemberOfCollection
AssignedSequence
An unsigned integer 'n' that indicates the relative position of members within a Collection. When 'n' is a positive integer, it indicates a place in
the sequence of members, with smaller integers indicating earlier positions in the sequence. The special value '0' indicates 'don't care'. If two or
more members have the same non-zero sequence number, then the ordering between those members is irrelevant, but they must all be ordered
at the appropriate place in the overall sequence. A series of examples will make ordering of members clearer: If all members have the same
sequence number, regardless of whether it is '0' or non-zero, any order is acceptable. The values are: 1:MEMBER A 2:MEMBER B 1:MEMBER C
3:MEMBER D indicate two acceptable orders: A,C,B,D or C,A,B,D, because A and C can be ordered in either sequence, but only at the '1' position.
Note: The non-zero sequence numbers do not need to start with '1', and they do not need to be consecutive. However, the sequencenumbers
must reflect their relative magnitude.
Collection The Collection that aggregates members.
Member The aggregated member of the Collection.
DCIM_MemberOfCollection
Collection The Collection that aggregates members.
Member The aggregated member of the Collection.
DCIM_OwningCollectionElement
OwnedElement The Collection owned or controlled by the ManagedElement.
OwningElement The ManagedElement acting as the 'owner' or object that isresponsible for the control of the Collection.