Reference Guide

Dell OpenManage Client Instrumentation Reference Guide
file:///T|/htdocs/SOFTWARE/smcliins/cli80/EN/refgd/index.htm[10/19/2012 9:56:27 AM]
16197 - Memory Device
16198 - USB
16199 - Monitor
16200 - SCSI
16201..65535 - Vendor Reserved
PrimaryStatus
Provides a high level status value, intended to align with Red-Yellow-Green type representation of status. It should be used in conjunction with
DetailedStatus to provide high level and detailed health status of the ManagedElement and its subcomponents.
Possible values are:
0 - Unknown - Indicates the implementation is in general capable of returning this property, but is unable to do so at this time.
1 - OK - Indicates the ManagedElement is functioning normally.
2 - Degraded - Indicates the ManagedElement is functioning below normal.
3 - Error - Indicates the ManagedElement is in an Error condition.
.. - DMTF Reserved
0x8000.. - Vendor Reserved
RequestedSpeed The requested bandwidth of the Port in Bits per Second. The actual bandwidth is reported in LogicalPort.Speed.
RequestedState
An integer enumeration that indicates the last requested or desired state for the element, irrespective of the mechanism through which it was
requested. The actual state of the element is represented by EnabledState. This property is provided to compare the last requested and current
enabled or disabled states. Note that when EnabledState is set to 5 ("Not Applicable"), then this property has no meaning. Refer to the
EnabledState property description for explanations of the values in the RequestedState enumeration.
Note: The value "No Change" (5) has been deprecated instead of indicating the last requested state is "Unknown" (0). If the last requested or
desired state is unknown, RequestedState should have the value "Unknown" (0), but may have the value "No Change" (5). There are two new
values in RequestedState that build on the statuses of EnabledState. These are "Reboot" (10) and "Reset" (11).
Shut Down requests an orderly transition to the Disabled state, and may involve removing power, to completely erase any existing state. The
Disabled state requests an immediate disabling of the element, such that it will not execute or accept any commands or processing requests.
This property is set as the result of a method invocation (such as Start or StopService on CIM_Service), or can be overridden and defined as
WRITEable in a subclass. The method approach is considered superior to a WRITEable property, because it allows an explicit invocation of the
operation and the return of a result code. If knowledge of the last RequestedState is not supported for the EnabledLogicalElement, the property
is NULL or has the value 12 "Not Applicable".
Possible values are:
0 - Unknown - Indicates the last requested state for the element is unknown.
2 - Enabled
3 - Disabled
4 - Shut Down
5 - No Change
6 - Offline - Indicates that the element has been requested to transition to the Enabled but Offline EnabledState.
7 - Test
8 - Deferred
9 - Quiesce
10 - Reboot - Indicates a "Shut Down" and then moving to an "Enabled" state.
11 - Reset - Indicates that the element is first "Disabled" and then "Enabled".
12 - Not Applicable
.. - DMTF Reserved
32768..65535 - Vendor Reserved
Security
An enumeration indicating the operational security for the Controller. For example, information that the Device's external interface is locked out
(value=4) or "Boot Bypass" (value=6) can be described using this property.
Possible values are:
1 - Other
2 - Unknown
3 - None
4 - External Interface Locked Out
5 - External Interface Enabled
6 - Boot Bypass
SerialPortCapabilities
The capabilities of this Serial port.
Possible values are:
1 - Other
2 - Unknown
3 - XT/AT compatible
4 - 16450 compatible
5 - 16550 compatible
6 - 16550A compatible
160 - 8251 compatible
161 - 8251FIFO compatible
SystemCreationClassName The CreationClassName of the scoping system.
SystemName The System Name of the scoping system.
TransitioningToState
Indicates the target state to which the instance is transitioning.
Possible values are:
0 - Unknown
2 - Enabled
3 - Disabled
4 - Shut Down
5 - No Change - Indicates that no transition is in progress.
6 - Offline
7 - Test
8 - Defer
9 - Quiesce
10 - Reboot
11 - Reset
12 - Not Applicable - Indicates the implementation does not support representing ongoing transitions.
A value other than 5 or 12 identifies the state to which the element is in the process of transitioning.
DCIM_USBPort
CreationClassName
Indicates the name of the class or the subclass used in the creation of an instance. When used with the other key properties of this class, this
property allows all instances of this class and its subclasses to be uniquely identified.
DeviceID An address or other identifying information used to uniquely name the LogicalDevice.
ElementName
A user-friendly name for the object. This property allows each instance to define a user-friendly name in addition to its key properties, identity
data, and description information.
Note: The Name property of ManagedSystemElement is also defined as a user-friendly name. But, it is often subclassed to be a Key. It is not
reasonable that the same property can convey both identity and a user-friendly name, without inconsistencies. Where Name exists and is not a
Key (such as for instances of LogicalDevice), the same information can be present in both the Name and ElementName properties.
An enumerated value indicating an administrator's default or startup configuration for the Enabled State of an element.
Possible values are:
2 - Enabled
3 - Disabled