Reference Guide

Dell OpenManage Client Instrumentation Reference Guide
file:///T|/htdocs/SOFTWARE/smcliins/cli80/EN/refgd/index.htm[10/19/2012 9:56:27 AM]
4 - LAN
5 - PXE boot enable
6 - LAN or WLAN
7 - WLAN only
Wake-On-LAN
If disabled then the system will not respond to magic packets or other means of wake-on-LAN. The NIC chip
section that looks for packets will not be powered.
If all-in-card then any NIC plugged into an expansion slot will be enabled for Wake-on-LAN. There's only one
small white NIC power connector per riser, so if the user has two or more add-in NICs, whichever one is
plugged into the special power connector is the source of any Wake-on-LAN signal.
If on board then the on-board NIC is enabled for Wake-on-LAN.
Possible values are:
1 - Disable
2 - Add-in-card
3 - Onboard
4 - Enable all
Wake-On-LAN Boot Override
If enabled then when the system powers on due to a Wake-on-LAN event, the NIC boot-ROM is automatically
given the highest boot priority, pre-pending the PXE boot-ROM to the system’s current boot sequence. If the
system powers on due to some other event, this selection does not influence the boot sequence. If disabled
then the boot override feature is disabled and the system boot sequence is in effect for all types of system
power on.
Possible values are:
1 - Disable
2 - Enable
Watchdog Timer
The system will/will not reboot/reset if the watchdog timer expires
Possible values are:
1 - Disable
2 - Enable
Wireless Adapter
Enables or disables Wireless Adapter.
Possible values are:
1 - Disable
2 - Auto
Wireless Device
If disabled then wireless devices are always disabled.
If set to APP then wireless devices can be controlled by an application such as QuickSet
If set to Hotkey then wireless devices can be controlled by an application such as QuickSet
Possible values are:
1 - Disable
2 - APP
3 - Hotkey
WiFi Catcher Changes
Permits or Denies WiFi Catcher changes. If the administrator password is not set, this setting will have no
effect.
Possible values are:
1 - Deny
2 - Permit
WiFi Locator
Enables or disables the WiFi Locator.
Possible values are:
1 - Disable
2 - Enable
Wireless LAN
Enables or disables the wireless LAN module.
Possible values are:
1 - Disable
2 - Enable
Wireless Switch Bluetooth Control
Enables or disables wireless switch Bluetooth control.
Possible values are:
1 - Disable
2 - Enable
Wireless Switch Cellular Control
Enables or disables wireless switch cellular control. This switch has no effect on the state of the cellular radio
for systems with a physical wireless on/off switch.
Possible values are:
1 - Disable
2 - Enable
Wireless Switch Change
Permits or Denies Wireless Switch changes. If the administrator password is not set, this setting will have no
effect.
Possible values are:
1 - Deny
2 - Permit
Wireless Switch Wireless LAN Control
Enables or disables wireless switch wireless LAN control. This switch has no effect on the state of the wireless
LAN radio for systems with a physical wireless on/off switch.
Possible values are:
1 - Disable
2 - Enable
Wireless UWB
Enables or disables UWB card.
Possible values are:
1 - Disable
2 - Enable
WxAN Radio
Possible values are:
1 - Disable
2 - WLAN on
3 - WWAN on
If set to 'disable' then it disables both WLAN and WWAN;
If set to 'WLAN ON' then it toggles between WLAN radio on and WWAN radio off;
If set to 'WWAN ON' then it toggles between WWAN radio on and WLAN radio off.
Alerts in OMCI
Alerts are generated when a system’s state of interest changes. There are two basic types of alerting: local alerting to the current computer user and remote
alerting to a management application. Dell OpenManage Client Instrumentation (OMCI) handles both types of alerting.