Reference Guide

Dell OpenManage Client Instrumentation Reference Guide
file:///T|/htdocs/SOFTWARE/smcliins/cli76/en/refgd/Index.htm[11/16/2012 2:58:47 PM]
SystemName The scoping System's Name.
Tolerance Indicates the tolerance of the Sensor for the measured property. Tolerance, along with Resolution and Accuracy, is used to calculate the actual value of the measured physical property. Tolerance may vary
depending on whether the Device is linear over its dynamic range.
UnitModifier The unit multiplier for the values returned by this Sensor.
UpperThresholdCritical The Sensor's threshold values specify the ranges (min and max values) for determining whether the Sensor is operating under Normal, NonCritical, Critical or Fatal conditions. If the CurrentReading is between
UpperThresholdCritical and UpperThresholdFatal, then the CurrentState is Critical.
UpperThresholdFatal The Sensor's threshold values specify the ranges (min and max values) for determining whether the Sensor is operating under Normal, NonCritical, Critical or Fatal conditions. If the CurrentReading is above
UpperThresholdFatal, then the CurrentState is Fatal.
UpperThresholdNonCritical The Sensor's threshold values specify the ranges (min and max values) for determining whether the Sensor is operating under Normal, NonCritical, Critical or Fatal conditions. If the CurrentReading is between
LowerThresholdNonCritical and UpperThresholdNonCritical, then the Sensor is reporting a normal value. If the CurrentReading is between UpperThresholdNonCritical and UpperThresholdCritical, then the
CurrentState is NonCritical.
CONFIGURATION
This section provides information about configuring boot device, hard disk drive sequence, password, internal speaker, power, and so on. Table 1-6 lists Dell OMCI Configuration classes and properties.
Table 1-6: Dell OpenManage Client Instrumentation Configuration Classes and Properties
Dell_BootDeviceSequence
BootDeviceName The name of this boot device as specified by the BIOS.
BootOrder The order of this device in the boot device priority list.
The following values are defined:
1 = This device is the first in the list
2 = This device is the second in the list, and so on.
DellInstanceID Index used to identify this boot device.
Status Set to Enabled if this device is enabled in the boot sequence, Set to Disabled if this device is disabled in the boot sequence.
The following values are defined:
0 = Disabled
1 = Enabled
Dell_Configuration
ACPowerRecoveryMode This attribute allows the setting of the AC Power Recovery Mode in BIOS. Unsupported means that this system BIOS does not support the setting of the AC Power Recovery Mode.
The following values are defined:
1 = Other
2 = Unsupported
3 = Off
4 = Last
5 = On
BootPassword This property allows Dell OpenManage to keep track of the BIOS boot password for verification purposes. Users need not view or change this property. Only the network administrator should change this
password.
BootPasswordVerification This property indicates the result of the last BIOS boot password verification operation executed by the system. A verification occurs each time Dell OpenManage prompts the user to enter a password.
The following values are defined:
0 = Password not matched
1 = Password matched
2 = Not yet verified
3 = Password disabled by jumper
4 = Password not enabled
Caption The caption of the device.
Description A short description of the device.
EnableDisableBIS This property allows the enabling/disabling of the Boot Integrity Services (BIS) in BIOS. Unsupported means that this system BIOS does not support BIS.
The following values are defined:
1 = Other
2 = Unsupported
3 = Accept
4 = Deny
5 = Reset
ExtensionTokens This property determines the extension tokens that are available in this system.
ForcePXEonNextBoot This attribute allows the enabling/disabling of Force PXE on Next Boot in BIOS. Unsupported means that this system BIOS does not support Force PXE on next boot.
The following values are defined:
1 = Other
2 = Unsupported
3 = Enabled
4 = Disabled
GlobalDisplaySeverityLevel The indication severity level required for display to the local console.
The following values are defined:
0= Unknown
1 = Other
2 = Information