Users Guide
Table Of Contents
- Dell Lifecycle Controller Integration Version 3.0 For Microsoft System Center Configuration Manager User's Guide
- Contents
- Introduction to Dell Lifecycle Controller Integration (DLCI) for Microsoft System Center Configuration Manager
- Use case scenarios
- Common prerequisites
- Editing and exporting the BIOS configuration profile of a system
- Creating, editing, and saving a RAID profile of a system
- Comparing and updating the firmware inventory
- Deploying operating system on collection
- Exporting server profile to iDRAC vFlash card or network share
- Importing server profile from iDRAC vFlash card or network share
- Viewing and exporting Lifecycle Controller logs
- Working With NIC or CNA Profiles
- Using Dell Lifecycle Controller Integration
- Licensing for DLCI
- Configuring Dell Lifecycle Controller Integration with Dell Connections License Manager
- Configuring target systems
- Auto-discovery and handshake
- Applying Drivers from the task sequence
- Creating a task sequence media bootable ISO
- System Viewer utility
- Configuration utility
- Launching the integrated Dell Remote Access Controller console
- Task Viewer
- Additional tasks you can perform with Dell Lifecycle Controller Integration
- Configuring security
- Validating a Dell factory-issued Client Certificate on the Integrated Dell Remote Access Controller for auto-discovery
- Pre-authorizing systems for auto-discovery
- Changing the administrative credentials used by Dell Lifecycle Controller Integration for Configuration Manager
- Using the Graphical User Interface
- Using the Array Builder
- Defining rules with the Array Builder
- Creating a RAID Profile using Array Builder
- About creating Array Builder
- Controllers
- Adding a Controller
- Editing a Controller
- Deleting a Controller
- Variable conditions
- Adding a new variable condition
- Editing a variable condition
- Deleting a variable condition
- Arrays
- Adding a new array
- Editing an array
- Deleting an array
- Logical drives also known as virtual disks
- Adding a new logical drive
- Editing a logical drive
- Deleting a logical drive
- Disks (array disks)
- Adding a new disk
- Changing a disk
- Deleting a disk
- Importing a profile
- Using the Configuration Utility
- Creating a Lifecycle Controller boot media
- Configuring hardware and deploying the operating system
- Comparing and updating firmware inventory for systems in a collection
- Viewing the hardware inventory
- Verifying Communication with Lifecycle Controller
- Modifying credentials on Lifecycle Controllers
- Viewing and exporting Lifecycle Controller logs for a collection
- Platform restore for a collection
- Comparing NIC or CNA profiles against systems in a collection
- Using the Import Server Utility
- Using the System Viewer Utility
- Viewing and editing BIOS configuration
- Viewing and configuring RAID
- Configuring iDRAC profiles for a system
- Configuring NICs and CNAs for a system
- Comparing and updating firmware inventory
- Comparing hardware configuration profile
- Viewing Lifecycle Controller logs
- Viewing the hardware inventory for the system
- Platform restore for a system
- Troubleshooting
- Configuring Dell provisioning web services on IIS
- Dell auto-discovery network setup specification
- Upgrade or repair issues
- Troubleshooting the viewing and exporting of Lifecycle Controller logs
- Issues and resolutions
- Dell Connections License Manager status messages
- ESXi or RHEL deployment on Windows systems moves to ESXi or RHEL collection, but not removed from Windows Managed Collection
- Related documentation and resources
Using Dell Lifecycle Controller Integration
This chapter discusses the various operations that you can perform after you install DLCI on Configuration Manager.
Before you begin using DLCI for Configuration Manager, ensure that the target system is auto-discovered and present in the All
Dell Lifecycle Controller Servers collection on the Configuration Manager console.
DLCI for Configuration Manager enables you to perform the following operations on all Dell systems under a collection:
● Configure the target systems. For more information, see Configuring target systems on page 19.
● Apply drivers on the task sequence. For more information, see Applying Drivers from the task sequence on page 20.
NOTE: Select the Apply Drivers from Lifecycle Controller check box if you want to apply drivers from Lifecycle
Controller while deploying operating systems.
● Create a task sequence media. For more information, see Creating a task sequence media bootable ISO on page 20.
● Use the System Viewer utility on specific systems in a collection. For more information, see System Viewer utility on page
21.
● Use the Config Utility on a collection of Dell systems. For more information, see Configuration utility on page 22.
●
Launch the iDRAC console by right-clicking on any system discovered under All Dell Lifecycle Controller Servers on the
Configuration Manager console, or any system on the Task Viewer. For more information, see Launching the integrated Dell
Remote Access Controller console on page 22.
● Use the Task Viewer to view the status of tasks handled by DLCI for Configuration Manager. For more information, see
Task Viewer on page 23.
Topics:
• Licensing for DLCI
• Configuring Dell Lifecycle Controller Integration with Dell Connections License Manager
• Configuring target systems
• Auto-discovery and handshake
• Applying Drivers from the task sequence
• Creating a task sequence media bootable ISO
• System Viewer utility
• Configuration utility
• Launching the integrated Dell Remote Access Controller console
• Task Viewer
• Additional tasks you can perform with Dell Lifecycle Controller Integration
Licensing for DLCI
This release of DLCI is licensed. For more information on licensing; In Configuration Manager select Assets and Compliance >
Overview > Device Collections > Dell Lifecycle Controller > License Instructions.
Configuring Dell Lifecycle Controller Integration with
Dell Connections License Manager
Confirm that these prerequisites are available:
● Site Server or Configuration Manager console components of Configuration Manager 2012, Configuration Manager 2012 SP1,
or Configuration Manager 2012 R2 are installed and configured.
● Dell Connections License Manager application is installed and configured with a valid license.
To configure Dell Lifecycle Controller Integration with Dell Connections License Manager.
1. In Configuration Manager 2012, under Device Collections, right-click All Dell Lifecycle Controller Servers and select
Dell Lifecycle Controller > Dell Connections License Manager Configuration Utility.
3
18 Using Dell Lifecycle Controller Integration