Dell Latitude E6320 Owner's Manual Regulatory Model: P12S Regulatory Type: P12S001
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2012 Dell Inc.
Contents Notes, Cautions, and Warnings..................................................................2 บทที 1: ่ การทำงานกับส่วนประกอบภายในของคอมพิวเตอร์..................................................9 การดำเนินการกับส่วนประกอบภายในคอมพิวเตอร์....................................................................................9 เครื่องมือที่แนะนำให้ใช้...............................................................................................................10 การปิดคอมพิวเตอร์....................
Installing The Optical Drive.............................................................................................28 บทที่ 8: Base Cover........................................................................................31 Removing The Base Cover..............................................................................................31 Installing The Base Cover...............................................................................................32 บทที่ 9: เมมโมรี่การ์ด..........
Removing The Bluetooth Card.........................................................................................57 Installing The Bluetooth Card..........................................................................................58 บทที 17: ่ แผง LED..............................................................................................61 Removing The LED Board................................................................................................61 Installing The LED Board........
บทที่ 25: ลำโพง...................................................................................................95 Removing The Speakers..................................................................................................95 Installing The Speakers...................................................................................................97 บทที 26: ่ พอร์ต DC-In........................................................................................99 Removing The DC-In Port........
Virtualization Support.............................................................................................129 Wireless..................................................................................................................129 Maintenance...........................................................................................................130 System Logs............................................................................................................
การทำงานกับส่วนประกอบภายในของคอมพิวเตอร์ 1 การดำเนินการกับส่วนประกอบภายในคอมพิวเตอร์ ปฏิบัติตามคำแนะนำต่อไปนี้เพื่อปกป้องคอมพิวเตอร์จากความเสียหาย และเพื่อความปลอดภัยของตัวคุณเอง ขั้นตอนที่แจ้งในเอกสารนี้ แนะนำภายใต้เงื่อนไขดังต่อไปนี้ ยกเว้นมีระบุไว้เป็นอย่างอื่น: • • • คุณได้ปฏิบัติตามขั้นตอนในหัวข้อ การทำงานกับส่วนประกอบภายในคอมพิวเตอร์ คุณได้อ่านข้อมูลด้านความปลอดภัยที่ให้มาพร้อมกับคอมพิวเตอร์ของคุณแล้ว ส่วนประกอบที่สามารถเปลี่ยนใหม่ หรือในกรณีของส่วนประกอบจัดซื้อแยกจะต้องติดตั้งตามขั้นตอนการถอดโดยย้
ข้อควรระวัง: ปลดสายเครือข่ายโดยถอดสายออกจากคอมพิวเตอร์ก่อน แล้วจึงถอดสายจากอุปกรณ์เครือข่าย 4. ถอดสายโทรศัพท์หรือสายเครือข่ายทั้งหมดออกจากคอมพิวเตอร์ 5. ถอดปลั๊กคอมพิวเตอร์และอุปกรณ์ต่าง ๆ ทั้งหมดที่ต่ออยู่กับคอมพิวเตอร์ออกจากเต้ารับไฟฟ้า 6. ปิดฝาจอแสดงผลและพลิกคอมพิวเตอร์คว่ำลงบนพื้นผิวเรียบ หมายเหตุ: คุณต้องถอดแบตเตอรี่หลักออกก่อนทำการดูแลรักษาคอมพิวเตอร์ เพื่อป้องกันไม่ให้เมนบอร์ดเสียหาย 7. ถอดแบตเตอรี่หลักออก 8. พลิกคอมพิวเตอร์ขึ้น 9. เปิดจอแสดงผล 10.
– สำหรับ Windows XP: คลิก Start → Turn Off Computer → Turn Off คอมพิวเตอร์จะปิดทำงานหลังจากระบบปฏิบัติ การปิดการทำงานเสร็จสิ้น 2.
ExpressCard 2 Removing The ExpressCard 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the ExpressCard to release it from the computer. 3. Slide the ExpressCard out of the computer.
Related Links Installing the ExpressCard Installing the ExpressCard 1. Slide the ExpressCard into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer.
การ์ด SD 3 Removing The Secure Digital (SD) Card 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the SD card to release it from the computer. 3. Slide the SD card out of the computer.
Related Links Installing the Secure Digital (SD) Card Installing the Secure Digital (SD) Card 1. Slide the Secure Digital (SD) card into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer.
แบตเตอรี่ 4 Removing The Battery 1. Follow the procedures in Before Working On Your Computer. 2. Slide the battery latches to unlock the battery. 3. Slide the battery out and remove it from the computer.
Related Links Installing The Battery Installing The Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer.
Subscriber Identity Module (SIM) Card 5 Removing The Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Press in on the SIM card to release it from the computer. 4. Slide the SIM card out from the computer.
Related Links Installing the Subscriber Identity Module (SIM) Card Installing the Subscriber Identity Module (SIM) Card 1. Slide the SIM card into its compartment. 2. Install the battery. 3. Follow the procedures in After Working Inside Your Computer.
ฮาร์ดไดร์ฟ 6 Removing The Hard Drive 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the screws that secure the hard drive to the computer. 4. Slide and remove the hard drive out of the computer.
5. Remove the screw that secures the hard-drive caddy to the hard drive. 6. Pull and remove the hard-drive caddy away from the hard drive.
Related Links Installing The Hard Drive Installing The Hard Drive 1. Attach the hard-drive caddy to the hard drive. 2. Tighten the screws to secure the hard-drive caddy to the hard drive. 3. Slide the hard drive into the computer. 4. Replace and tighten the screws that secure the hard drive to the computer. 5. Install the battery. 6. Follow the procedures in After working inside your computer.
ออพติคอลไดร์ฟ 7 Removing The Optical Drive 1. Follow the procedures in Before Working On Your Computer. 2. Press and release the optical drive latch. 3. Pull the optical drive out of the computer. 4. Pull the optical drive door from one side to release it.
5. Pull the other side of the optical drive door to release it completely from the optical drive. 6. Remove the screw that secures the drive latch to the optical drive.
7. Remove the drive latch from the optical drive. 8. Remove the screws that secures the drive latch bracket to the optical drive.
9. Remove the drive latch bracket from the optical drive. Related Links Installing The Optical Drive Installing The Optical Drive 1. Insert the drive latch bracket into the optical drive. 2. Tighten the screws to secure the drive latch bracket to the optical drive. 3. Insert the drive latch into the optical drive. 4. Tighten the screw to secure the drive latch to the optical drive. 5. Push the optical drive door to insert it completely into the optical drive. 6.
Removing The Optical Drive 29
Base Cover 8 Removing The Base Cover 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) Card. 4. Remove the screws that secure the base cover to the computer. 5. Lift the base cover up and away from the computer.
Related Links Installing The Base Cover Installing The Base Cover 1. Place the base cover to align the screw holes correctly with the computer. 2. Replace and tighten the screws to secure the base cover to the computer. 3. Install the Secure Digital (SD) Card. 4. Follow the procedures in After Working Inside Your Computer.
เมมโมรี่การ์ด 9 Removing The Memory 1. Follow the procedures in Before Working On Your Computer 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Pry the retention clips away from the memory module until it pops up. 6. Remove the memory module from the computer.
Related Links Installing The Memory Installing The Memory 1. Insert the memory module into the memory slot. 2. Press the clips to secure the memory module to the system board. 3. Install the base cover. 4. Install the Secure Digital (SD) card. 5. Install the battery 6. Follow the procedures in After Working Inside Your Computer.
ถ่านกระดุม 10 Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the coin-cell battery cable from the system board. 6. Release and remove the coin-cell battery from the computer.
Related Links Installing The Coin-Cell Battery Installing The Coin-Cell Battery 1. Place the coin-cell battery in its location. 2. Connect the coin-cell battery cable to the system board. 3. Install the base cover. 4. Install the Secure Digital (SD) card. 5. Install the battery 6. Follow the procedures in After working inside your computer.
การ์ดเครือข่ายภายในไร้สาย (WLAN) 11 Removing The Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the antenna cables from the WLAN card. 6. Remove the screw that secures the WLAN card to the computer.
7. Remove the WLAN card from its slot on the system board. Related Links Installing The Wireless Local Area Network (WLAN) Card Installing The Wireless Local Area Network (WLAN) Card 1. Insert the WLAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw that secures the WLAN card to the computer. 3. Connect the antenna cables according to the color code on the WLAN card. 4. Install the base cover.
5. Install the Secure Digital (SD) card. 6. Install the battery 7. Follow the procedures in After Working Inside Your Computer.
การ์ดเครือข่ายวงกว้างไร้สาย (WWAN) 12 Removing The Wireless Wide Area Network (WWAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the antenna cables from the WWAN card. 6. Remove the screw that secures the WWAN card to the computer.
7. Remove the WWAN card from the computer. Related Links Installing The Wireless Wide Area Network (WWAN) Card Installing The Wireless Wide Area Network (WWAN) Card 1. Insert the WWAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw to secure the WWAN card to the computer. 3. Connect the antenna cables according to the color code on the WLAN card. 4. Install the base cover.
5. Install the Secure Digital (SD) card. 6. Install the battery 7. Follow the procedures in After Working Inside Your Computer.
Keyboard Trim 13 Removing The Keyboard Trim 1. Follow the procedures in Before Working On Your Computer. 2. Using a plastic scribe, pry under the keyboard trim to release it from the computer. 3. Lift the keyboard trim to release the tabs and remove it from the computer.
Related Links Installing The Keyboard Trim Installing The Keyboard Trim 1. Align the keyboard trim with the keyboard and snap it into place. 2. Follow the procedures in After Working Inside Your Computer.
แป้นพิมพ์ 14 Removing The Keyboard 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the keyboard trim. 4. Remove the screws that secure the keyboard to the computer. 5. Remove the screws that secure the keyboard to the palmrest assembly.
6. Flip the keyboard over and lay it toward the display. 7. Lift the clip to release the keyboard cable and disconnect it from the computer.
8. Remove the keyboard from the computer. 9. Remove the tape securing the keyboard cable from the keyboard.
10. Disconnect and remove the keyboard cable from the keyboard. Related Links Installing The Keyboard Installing The Keyboard 1. Connect the keyboard cable and secure it to the keyboard using the tape. 2. Connect the keyboard cable to its connector on the system board. 3. Turn the keyboard over and lay it on the palmrest. 4. Replace and tighten the screws to secure the keyboard to the palmrest assembly. 5. Replace and tighten the screws to secure the keyboard to the computer.
6. Install the battery. 7. Install the keyboard trim 8. Follow the procedures in After Working Inside Your Computer.
15 ที่พักมือ Removing The Palmrest Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the screws that secure the palmrest assembly to the computer. 11.
– bluetooth – contactless smart card reader – ExpressCard – fingerprint reader 12. Remove the screws to release the palmrest assembly from the system board. 13. Lift the palmrest assembly along the edges to unlock the tabs and remove it away from the computer.
Related Links Installing The Palmrest Assembly Installing The Palmrest Assembly 1. Align the palmrest assembly with the computer and snap it into place. 2. Replace and tighten the screws to secure the palmrest assembly to the system board. 3. Connect the following cables to the system board: – LED board – touchpad – bluetooth – contactless smart card reader – Express Card – fingerprint reader 4. Replace and tighten the screws to secure the palmrest assembly to the computer. 5.
Related Links Removing The Palmrest Assembly 56
การ์ด Bluetooth 16 Removing The Bluetooth Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the screws that secure the bluetooth card to the palmrest assembly. 12.
13. Release and remove the bluetooth cable from the bluetooth card. Related Links Installing The Bluetooth Card Installing The Bluetooth Card 1. Connect the bluetooth cable to the bluetooth card. 2. Place the bluetooth card on the palmrest assembly. 3. Replace and tighten the screw to secure the bluetooth card to the palmrest assembly. 4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard.
9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer.
แผง LED 17 Removing The LED Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Release the LED board cable from the routing channel. 12. Remove the screw that secures the LED board to the palm rest assembly.
13. Remove the LED board from the palm rest assembly. Related Links Installing The LED Board Installing The LED Board 1. Align the LED board on the palmrest. 2. Replace and tighten the screw that secure the LED board to the palmrest. 3. Route the LED board cable to its original position.
4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer.
Smart Card Reader 18 Removing The Smart Card Reader 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly 11. Disconnect the smart card reader cable from the system board. 12.
13. Lift and remove the smart card reader from the computer. Related Links Installing The Smart Card Reader Installing The Smart Card Reader 1. Place the smart card reader to its original position on the computer. 2. Replace and tighten the screws to secure the smart card reader to the computer. 3. Connect the smart card reader cable to the system board. 4. Replace and tighten the screws to secure the palmrest assembly to the computer. 5. Install the palmrest assembly. 6. Install the keyboard.
8. Install the hard drive. 9. Install the ExpressCard. 10. Install the base cover. 11. Install the optical drive. 12. Install the Secure Digital (SD) card. 13. Install the battery. 14. Follow the procedures in After Working Inside Your Computer.
Media Board 19 Removing The Media Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Disconnect the media board cable from the system board. 12. Remove the screws that secures the media board to the computer.
13. Remove the media board from the computer. Related Links Installing The Media Board Installing The Media Board 1. Align the media board to its original position on the computer. 2. Replace and tighten the screws to secure the media board to the computer. 3. Connect the media board cable to the system board. 4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive.
8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer.
Display Hinges 20 Removing The Display Hinge Covers 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the screws that secure the display hinge covers to the computer. 12.
Related Links Installing The Display Hinge Covers Installing The Display Hinge Covers 1. Place the display hinges in the appropriate positions. 2. Replace and tighten the screws to secure the display hinge covers to the computer. 3. Install the palmrest assembly. 4. Install the keyboard. 5. Install the keyboard trim. 6. Install the hard drive. 7. Install the ExpressCard. 8. Install the base cover. 9. Install the optical drive. 10. Install the Secure Digital (SD) card. 11.
ชุดจอแสดงผล 21 Removing The Display Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the display hinge covers. 12. Release the antenna cables from the computer.
13. Remove the screws that secure the display assembly to the computer. 14. Pull out the antenna cables from their routing channels? 15. Remove the screws that secure the display cable bracket to the system board.
16. Remove the display cable bracket from the computer. 17. Pull the display cable to disconnect it from the system board.
18. Remove the screw that secures the display assembly to the computer. 19. Remove the display assembly from the computer. Related Links Installing The Display Assembly Installing The Display Assembly 1. Align the display assembly into its original position on the computer. 2. Replace and tighten the screw to secure the display assembly to the computer. 3. Replace and connect the display cable to the system board. 4. Align the display cable bracket to its original position.
5. Replace and tighten the screws to secure the display cable bracket to the system board. 6. Route the antenna cables through the system board. 7. Replace and tighten the screws to secure the display panel to the computer. 8. Route the antenna cables to their original position. 9. Install the display hinge covers. 10. Install the palmrest assembly. 11. Install the keyboard. 12. Install the keyboard trim. 13. Install the hard drive. 14. Install the ExpressCard. 15. Install the base cover. 16.
เมนบอร์ด 22 Removing The System Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13.
19. Remove the screws that secure the system board to the computer. 20. Lift the system board to locate the power supply cable.
21. Disconnect the power supply cable from the system board. 22. Lift and remove the system board from the computer.
NOTE: Steps 23 and 24 are applicable for computers that shipped in the United States of America. 23. Flip the system over and remove the screw that secures the TAA board. 24. Remove the TAA board from the system.
Related Links Installing The System Board Installing The System Board 1. Place the TAA board to its original position. NOTE: Steps 1 and 2 are applicable for computers that shipped in the United States of America. 2. Replace and tighten the screw to secure the TAA board to the computer. 3. Align the system board into its original position on the computer. 4. Connect the power supply cable. 5. Replace and tighten the screws to secure the system board to the computer. 6.
17. Install the battery. 18. Follow the procedures in After Working Inside Your Computer.
ฮีทซิงค์ 23 Removing The Heat-Sink Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12.
20. Loosen the screws that secure the heat-sink assembly to the system board. 21. Remove the heat-sink assembly from the system board.
Related Links Installing The Heat-Sink Assembly Installing The Heat-Sink Assembly 1. Align the heat-sink assembly to its original position on the system board. 2. Tighten the screws to secure the heat-sink assembly to the system board. 3. Connect the heat-sink cable to the system board. 4. Install the heat-sink assembly. 5. Install the display assembly. 6. Install the display hinge covers. 7. Install the palmrest assembly. 8. Install the keyboard. 9. Install the keyboard trim. 10.
แผง I/O 24 Removing The Input/Output Panel 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card.
19. Remove the I/O panel from the computer. Related Links Installing The Input/Output Panel Installing The Input/Output Panel 1. Replace the I/O panel in the computer 2. Tighten the screw securing the I/O panel to the computer. 3. Install the display assembly. 4. Install the display hinge covers. 5. Install the palmrest assembly.
6. Install the keyboard. 7. Install the keyboard trim. 8. Install the hard drive. 9. Install the ExpressCard. 10. Install the base cover. 11. Install the optical drive. 12. Install the Secure Digital (SD) card. 13. Install the battery. 14. Follow the procedures in After Working Inside Your Computer.
ลำโพง 25 Removing The Speakers 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the base cover. 4. Remove the Secure Digital (SD) card. 5. Remove the optical drive. 6. Remove the subscriber identity module (SIM) card. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13.
20. Remove the screws that secure the speakers to the computer. 21. Remove the speakers from the computer.
Related Links Installing The Speakers Installing The Speakers 1. Replace the speakers to their original position in the computer. 2. Tighten the screws to secure the speakers to the computer. 3. Route and connect the speaker cable. 4. Install the system board 5. Install the display assembly. 6. Install the display hinge covers. 7. Install the palmrest assembly. 8. Install the coin-cell battery. 9. Install the Wireless Local Area Network (WLAN) card 10.
พอร์ต DC-In 26 Removing The DC-In Port 1. Follow the procedures in Before Working on Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13.
20. Remove the DC-In bracket from the system. 21. Remove the DC-In port from the system.
Related Links Installing The DC-In Port Installing The DC-In Port 1. Replace the DC-In port to its original position in the computer. 2. Replace the DC-In bracket to its original position in the computer. 3. Tighten the screw to secure the DC-In bracket to the computer. 4. Install the system board 5. Install the display assembly. 6. Install the display hinge covers. 7. Install the palmrest assembly. 8. Install the media board 9. Install the Wireless Local Area Network (WLAN) card 10.
กรอบจอแสดงผล 27 Removing The Display Bezel 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Starting from the bottom, pry the bezel from inside the display assembly. 4. Remove the bezel from the display assembly.
Related Links Installing The Display Bezel Installing The Display Bezel 1. Place the display bezel onto the display assembly. 2. Work along to the top and bottom edges of the display bezel. 3. Press the left and right edges of the display bezel. 4. Install the battery. 5. Follow the procedures in After Working Inside Your Computer.
แผงจอแสดงผล 28 Removing The Display Panel 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the display bezel 4. Remove the screws that secures the display panel to the display assembly. 5. Flip the display panel over.
6. Disconnect the Low-Voltage Differential Signaling (LVDS) cable from the display panel. 7. Remove the display panel from the display assembly.
Related Links Installing The Display Panel Installing The Display Panel 1. Align the display panel in its original position on the display assembly. 2. Connect the Low-Voltage Differential Signaling (LVDS) cable to the display panel. 3. Tighten the screws to secure the display panel to the display assembly. 4. Install the display bezel 5. Install the battery 6. Follow the procedures in After Working Inside Your Computer.
กล้อง 29 Removing The Camera 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the display bezel. 4. Remove the display panel. 5. Disconnect the cable from the camera module. 6. Remove the screw that secures the camera and microphone to the display assembly.
7. Remove the camera from the display assembly. Related Links Installing The Camera Installing The Camera 1. Place the camera module to its original position in the display assembly. 2. Tighten the screw to secure the camera to the display assembly. 3. Connect the camera cable to the camera. 4. Install the display panel. 5. Install the display bezel. 6. Install the battery. 7. Follow the procedures in After working inside your computer.
Related Links Removing The Camera 111
30 รายละเอียดทางเทคนิค Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer.
Memory Minimum memory 2 GB Maximum memory 8 GB Audio Type four-channel high definition audio Controller IDT 92HD90 Stereo conversion 24-bit (analog-to-digital and digital-to-analog) Interface: Internal high definition audio External microphone-in/stereo headphones/external speakers connector Speakers two Internal speaker amplifier 0.
Ports and Connectors Network adapter one RJ-45 connector USB one 4-pin USB 2.0-compliant connector and one eSATA/USB 2.0-compliant connector Memory card reader one 5-in-1 memory card reader Contactless Smart Card Supported Smart Cards/ Technologies ISO14443A — 106 kbps, 212 kbps, 424 kbps, and 848 kbps ISO14443B — 106 kbps, 212 kbps, 424 kbps, and 848 kbps ISO15693 HID iClass FIPS201 NXP Desfire Display Type white Light Emitting Diode (WLED) display Size 13.
Keyboard Number of keys United States: 86 keys, United Kingdom: 87 keys, Brazil: 87 keys, and Japan: 90 keys Layout QWERTY/AZERTY/Kanji Touchpad Active Area: X-axis 80.00 mm Y-axis 40.70 mm Battery Type • • • 3-cell (30Wh) lithium ion battery with ExpressCharge 6-cell (60Wh) lithium ion battery with ExpressCharge 6-cell (58Wh) lithium ion battery Dimensions: 3-cell Depth 29.97 mm (1.18 inches) Height 19.80 mm (0.78 inch) Width 208.00 mm (8.19 inches) 6-cell Depth 54.10 mm (2.
Battery 3-cell and 6-cell (60Wh) Voltage approximately 1 hour to 80% capacity and 2 hours to 100% capacity 11.10 VDC Temperature range: Operating 0 °C to 35 °C (32 °F to 95 °F) Non-Operating –40 °C to 65 °C (–40 °F to 149 °F) Coin-cell battery 3 V CR2032 lithium coin cell AC Adapter Type 65 W and 90 W Input voltage 100 VAC to 240 VAC Input current (maximum) 1.50 A/1.60 A/1.70 A Input frequency 50 Hz to 60 Hz Output power 65 W and 90 W Output current 3.34 A and 4.
Environmental Temperature: Operating 0 °C to 35 °C (32 °F to 95 °F) Storage –40 °C to 65 °C (–40 °F to 149 °F) Relative humidity (maximum): Operating 10 % to 90 % (noncondensing) Storage 5 % to 95 % (noncondensing) Altitude (maximum): Operating –15.24 m to 3048 m (–50 ft to 10,000 ft) Non-Operating –15.24 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level 118 G1 as defined by ISA-71.
การตั้งค่าระบบ 31 Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password. • read the current amount of memory or set the type of hard drive installed. Before you use System Setup, it is recommended that you write down the System Setup screen information for future reference.
General Option Description System Information This section lists the primary hardware features of your computer. • • • • System Information Memory Information Processor Information Device Information Battery Information Displays the battery status and the type of AC adapter connected to the computer. Boot Sequence Allows you to change the order in which the computer attempts to find an operating system.
System Configuration Option Description NOTE: System Configuration contains options and settings related to integrated system devices. Depending on your computer and installed devices, the items listed in this section may or may not appear. Integrated NIC Allows you to configure the integrated network controller. The options are: • • • Disabled Enabled Enabled w/PXE Default Setting: Enabled w/PXE System Management Allows you to control the systems management mechanism.
Option Description Default Setting: COM1 SATA Operation Allows you to configure the internal SATA hard-drive controller. The options are: • • • • Disabled ATA AHCI RAID On Default Setting: RAID On NOTE: SATA is configured to support RAID mode. USB Controller Allows you to control the USB controller. The options are: • • • Enable USB Controller Diasanle USB Mass Storage Dev Disable USB Controller Default Setting: Enable USB Controller Diskette Drive Allows you to activate the diskette drives.
Option Description Keyboard illumination Allows you to configure the keyboard illumination feature. The options are: • • • • • Disabled Level is 25% Level is 50% Level is 50% Levels is 100% Default Setting: Level is 25% Drives Allows you to configure the SATA drives on board. The options are: • • • • SATA-0 SATA-1 SATA-4 SATA-5 Default Setting: All drives are enabled.
Option Description NOTE: Deleting the admin password automatically deletes the system password and the hard drive password. NOTE: Successful password changes take effect immediately. Default Setting: Not set System Password Allows you to set, change or delete the system password. NOTE: Successful password changes take effect immediately. Default Setting: Not set Internal HDD-0 Password Allows you to set or change the system's internal hard-disk drive.
Option Description OROM Keyboard Access Allows you to set an option to enter the Option ROM Configuration screens using hotkeys during boot. The options are: • • • Enable One Time Enable Disable Default Setting: Enable TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST. Default Setting: The option is disabled.
Option Description Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator password is set. Default Setting: Enable Admin Setup Lockout is not selected. Performance Option Description Multi Core Support Allows you to enable or disable multi-core support for the processor. The options are: • • • All 1 2 Default Setting: All Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature. Default Setting: Enable Intel SpeedStep is selected.
Power Management Option Description AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected. Default Setting: Wake on AC is not selected. Auto On Time Allows you to set the time at which the computer must turn on automatically. The options are: • • • Disabled Every Day Weekdays Default Setting: Disabled USB Wake Support Allows you to enable USB devices to wake the system from Standby.
Option Description ExpressCharge Allows you to enable or disable the ExpressCharge feature. The options are: • • Standard ExpressCharge Default Setting: ExpressCharge POST Behavior Option Description Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power adapters. Default Setting: Enable Adapter Warnings is selected.
Option Description Fn Key Emulation Allows you to set the option where the key is used to simulate the key feature. Default Setting: Enable Fn Key Emulation is selected. POST HotKeys Allows you enable the sign-on screen message display indicating the keystroke sequence to access the System Setup option menu. Default Setting: Enable F12 Boot Option Menu is selected. Fastboot Allows to set the option to speed up the boot process.
Option Description • • • WWAN WLAB Bluetooth Default Setting: All the options are selected. Wireless Device Enable Allows you to enable or disable the wireless devices Default Setting: All the options are selected. Maintenance Option Description Service Tag Displays the Service Tag of your computer. Asset Tag Displays the Asset Tag. SERR Messages Allows you to create a system asset tag.
การวินิจฉัยระบบ 32 Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the computer reads or writes data. Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is enabled.
Appearance Blinkin Solid g Solid Blinkin g Description Solid Solid Processor error Memory is detected but has errors Next Step Replace the system board. 1. Reseat the memory. 2. If two modules are installed remove one and test. Try the other module in the same slot and test. Test the other slot with both modules. 3. Replace the memory. 4. Replace the system board. Blinkin Blinkin Blinkin System board g g g error Replace the system board.
Appearance Off Description Blinkin Blinkin Modem error g g Next Step 1. Reseat the modem. 2. Replace the modem. 3. Replace the system board.
การติดต่อกับ Dell 33 การติดต่อกับ Dell หมายเหตุ: หากไม่สามารถเชื่อมต่ออินเทอร์เน็ต สามารถค้นหาข้อมูลติดต่อได้จากใบแจ้งหนี้ ใบกำกับสินค้า บิล หรือแคตา ล็อกสินค้าของ Dell Dell มีบริการความช่วยเหลือผ่านระบบออนไลน์และทางโทรศัพท์ การจัดหาบริการจะขึ้นอยู่กับประเทศและประเภทผลิตภัณฑ์ บริการบางตัวอาจไม่มีในพื้นที่ของคุณ การติดต่อฝ่ายขายของ Dell ฝ่ายบริการทางเทคนิคหรือฝ่ายบริการลูกค้าเพื่อแจ้งปัญหา: 1. กรุณาเข้าไปที่เว็บไซต์ support.dell.com 2. เลือกประเภทบริการที่เกี่ยวข้อง 3.
