Reference Guide

ManualsBrandsDell ManualsActive System ManageriDRAC7/8 with Lifecycle Controller Version 2.50.50.50

Table Of Contents

iDRAC 8/7 v2.50.50.50 RACADM CLI Guide

September 2017

Rev. A02

Summary of content (447 pages)

PAGE 1
iDRAC 8/7 v2.50.50.50 RACADM CLI Guide September 2017 Rev.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents Chapter 1: Introduction................................................................................................................. 9 New in this release.............................................................................................................................................................. 9 Supported RACADM Interfaces.......................................................................................................................................
PAGE 4
getsvctag............................................................................................................................................................................ 45 getsysinfo............................................................................................................................................................................45 gettracelog...................................................................................................................................
PAGE 5
vmdisconnect.................................................................................................................................................................... 112 Chapter 3: iDRAC Property Database Group and Object Descriptions......................................... 113 Displayable Characters....................................................................................................................................................114 idRacInfo......................................
PAGE 6
System.LCD.QualifierTemp (Read or Write)....................................................................................................... 187 System.LCD.QualifierWatt (Read or Write)........................................................................................................ 187 System.Location.............................................................................................................................................................. 188 System.Power.........................
PAGE 7
iDRAC.ServiceModule.iDRACHardReset (Read or Write)............................................................................... 271 iDRAC.SmartCard............................................................................................................................................................274 iDRAC.SNMP....................................................................................................................................................................274 iDRAC.SNMP.Alert.........
PAGE 8
BIOS.SysSecurity.TpmPpiBypassProvision..........................................................................................................371 BIOS.UefiBootSettings.................................................................................................................................................. 372 FC.FCDevice.....................................................................................................................................................................372 FC.FCTarget.
PAGE 9
1 Introduction This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for the following: ● iDRAC for Blade Servers ● iDRAC on Rack and Tower Servers Most of the commands mentioned in this document are applicable for multi-generation servers. That is, the commands are applicable for iDRAC6, iDRAC7, and iDRAC8.
PAGE 10
● Remote — Supports running RACADM commands from a remote management station such as a laptop or desktop. To run Remote RACADM commands, install the DRAC Tools utility from the OpenManage software on the remote computer. To run Remote RACADM commands: ○ Formulate the command as a SSH or Telnet RACADM command. For more information about the options, see RACADM Subcommand Details. To download the local RACADM tool from dell.com/support, click Servers, Storage & Networking in the General Support section.
PAGE 11
Example racadm get nic.nicconfig NIC.nicconfig.1 [Key=NIC.Integrated.1-1-1#nicconfig] NIC.nicconfig.2 [Key=NIC.Integrated.1-2-1#nicconfig] NIC.nicconfig.3 [Key=NIC.Integrated.1-3-1#nicconfig] NIC.nicconfig.4 [Key=NIC.Integrated.1-4-1#nicconfig] ● To display the object list for the specified group, run: racadm get device.. Example racadm get nic.nicconfig.2 [Key=NIC.Integrated.
PAGE 12
Home key: directs to the starting of the command. End key: directs to the end of the command. ● View the history of the commands that were run in the current session, press up and down arrow key. ● Exit the Autocomplete mode, enter Quit, Exit, or press Ctrl+D key. For example: ● Example 1: racadm> arp autoupdatescheduler clearasrscreen clearpending closessn clrraclog . . . . . . .
PAGE 13
● ● ● ● ● ● System events Storage devices Network devices Configuration Audit Updates You can view and filter logs based on the category and severity level. You can also export and add a work note to a log event. If you initiate configuration jobs using RACADM CLI or iDRAC web interface, the Lifecycle log captures the information about the user, interface used, and the IP address of the system from which you initiate the job.
PAGE 14
Table 2.
PAGE 15
Table 2.
PAGE 16
Accessing support content from the Dell EMC support site Access supporting content related to an array of systems management tools using direct links, going to the Dell EMC support site, or using a search engine. ● Direct links: ○ For Dell EMC Enterprise Systems Management and Dell EMC Remote Enterprise Systems Management—https:// www.dell.com/esmmanuals ○ For Dell EMC Virtualization Solutions—https://www.dell.com/SoftwareManuals ○ For Dell EMC OpenManage—https://www.dell.
PAGE 17
2 RACADM Subcommand Details This section provides detailed description of the RACADM subcommands including the syntax and valid entries. Topics: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Guidelines to Quote Strings Containing Special Characters When Using RACADM Commands help and help subcommand arp autoupdatescheduler cd cd..
PAGE 18
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • racresetcfg remoteimage rollback sensorsettings serveraction set setled setniccfg sshpkauth sslcertdownload sslcertupload sslcertview sslcertdelete sslcsrgen sslkeyupload sslresetcfg storage swinventory systemconfig systemerase systemperfstatistics techsupreport testemail testtrap testalert traceroute traceroute6 update usercertupload usercertview vflashsd vflashpartition vmdisconnect Guidelines to Quote Strings Containing Special Character
PAGE 19
For using double quotation marks: The following characters must be escaped by prepending a backward slash: ● $ (dollar sign) ● " (double quotation mark) ● ` (back quotation mark) help and help subcommand Table 3. help and help subcommand Description Lists all the subcommands available for use with RACADM and provides a short description about each subcommand. You may also type a subcommand, group, object or Fully Qualified Descriptor (FQDD) name after help.
PAGE 20
To run this subcommand, you must have the Server Control privilege. NOTE: ● The autoupdatescheduler subcommand can be enabled or disabled. ● Lifecycle Controller and CSIOR may not be enabled to run this subcommand. ● The autoupdatescheduler can be enabled or disabled. For more information, see LifecycleController.LCAttributes.autoupdate (Read or Write) ● The minimum Lifecycle Controller version required is Lifecycle Controller 1.3.
PAGE 21
● If the-dom option is non-'*', then the schedule repeats by month. ● If the-wom option is non-'*', then the schedule repeats by month. ● If the-dom and -wom options are '*' and the -dow option is non-'*', then the schedule repeats by week. ● If all the three -dom, -wom and -dow options are '*', then the schedule repeats by day. ● -rp — Specifies the repeat parameter. This parameter must be specified. ○ If the-dom option is specified, then the valid values for -rp are 1–12.
PAGE 22
Synopsis Input racadm> cd